- 23 May, 2014 40 commits
-
-
Archit Taneja authored
Add selection ioctl ops. For VPE, cropping makes sense only for the input to VPE(or V4L2_BUF_TYPE_VIDEO_OUTPUT/MPLANE buffers) and composing makes sense only for the output of VPE(or V4L2_BUF_TYPE_VIDEO_CAPTURE/MPLANE buffers). For the CAPTURE type, V4L2_SEL_TGT_COMPOSE results in VPE writing the output in a rectangle within the capture buffer. For the OUTPUT type, V4L2_SEL_TGT_CROP results in selecting a rectangle region within the source buffer. Setting the crop/compose rectangles should successfully result in re-configuration of registers which are affected when either source or destination dimensions change, set_srcdst_params() is called for this purpose. Signed-off-by:
Archit Taneja <archit@ti.com> Signed-off-by:
Kamil Debski <k.debski@samsung.com> Signed-off-by:
Mauro Carvalho Chehab <m.chehab@samsung.com>
-
Archit Taneja authored
Some parameters of the VPE descriptors were understood incorrectly. They are now fixed. The fixes are explained as follows: - When adding an inbound data descriptor to the VPDMA descriptor list, we intend to use c_rect as the cropped region fetched by VPDMA. Therefore, c_rect->width shouldn't be used to calculate the line stride, the original image width should be used for that. We add a 'width' argument which gives the buffer width in memory. - frame_width and frame_height describe the complete width and height of the client to which the channel is connected. If there are multiple channels fetching data and providing to the same client, the above 2 arguments should be the width and height of the region covered by all the channels. In the case where there is only one channel providing pixel data to the client (like in VPE), frame_width and frame_height should be the cropped width and cropped height respectively. The calculation of these params is done in the vpe driver now. - start_h and start_v is also used in the case of multiple channels to describe where each channel should start filling pixel data. We don't use this in VPE, and pass 0s to the vpdma_add_in_dtd() helper. - Some minor changes are made to the vpdma_add_out_dtd() helper. The c_rect param is used for specifying the 'composition' target, and 'width' is added to calculate the line stride. Signed-off-by:
-
Mauro Carvalho Chehab authored
Changeset 95d2608b created this function, but declared it as global, by mistake. Signed-off-by:
-
Archit Taneja authored
For OMAP and DRA7x, we generally allocate video and graphics buffers through omapdrm since the corresponding omap-gem driver provides DMM-Tiler backed contiguous buffers. omapdrm is a dma-buf exporter. These buffers are used by other drivers in the video pipeline. Add VB2_DMABUF flag to the io_modes of the vb2 output and capture queues. This allows the driver to import dma shared buffers. Reviewed-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
-
Archit Taneja authored
vpe fops(vpe_open in particular) should be called only when VPDMA firmware is loaded. File operations on the video device are possible the moment it is registered. Currently, we register the video device for VPE at driver probe, after calling a vpdma helper to initialize VPDMA and load firmware. This function is non-blocking(it calls request_firmware_nowait()), and doesn't ensure that the firmware is actually loaded when it returns. We remove the device registration from vpe probe, and move it to a callback provided by the vpe driver to the vpdma library, through vpdma_create(). The ready field in vpdma_data is no longer needed since we always have firmware loaded before the device is registered. A minor problem with this approach is that if the video_register_device fails(which doesn't really happen), the vpe platform device would be registered. however, there won't be any v4l2 device corresponding to it. Signed-off-by:
-
Hans Verkuil authored
If the saa7134 module is loaded with the saa7134_userptr set to 1, then USERPTR support is enabled. A check in buffer_prepare verifies that the pointer is page-aligned. Signed-off-by:
-
Hans Verkuil authored
Convert the saa7134 driver to vb2. Note that while this uses the vb2-dma-sg version, the VB2_USERPTR mode is disabled. The DMA hardware only supports DMAing full pages, and in the USERPTR memory model the first and last scatter-gather buffer is almost never a full page. In practice this means that we can't use the VB2_USERPTR mode. This has been tested with raw video, compressed video, VBI, radio, DVB and video overlays. Unfortunately, a vb2 conversion is one of those things you cannot split up in smaller patches, it's all or nothing. This patch switches the whole driver over to vb2, using the vb2 ioctl and fop helper functions. Signed-off-by:
-
Hans Verkuil authored
All dmaqueue's use saa7134_pgtable, so move it into struct saa7134_dmaqueue. The videobuf_queue priv_data field now points to the dmaqueue struct. Signed-off-by:
-
Hans Verkuil authored
Use consistent _vbq suffix for videobuf_queue fields. Signed-off-by:
-
Philipp Zabel authored
num_buffers can't be bigger than VIDEO_MAX_FRAME. This is assured by: num_buffers = min_t(unsigned int, req->count, VIDEO_MAX_FRAME); However, this value is overriden by: num_buffers = max_t(unsigned int, req->count, q->min_buffers_needed); It should, instead, use the previously calculated value as an input to max_t: num_buffers = max_t(unsigned int, num_buffers, q->min_buffers_needed); Signed-off-by:
Philipp Zabel <p.zabel@pengutronix.de> Reviewed-by:
-
Laurent Pinchart authored
The __vb2_queue_cancel function marks the queue as not streaming and then WARNs when buffers are still owned by the driver. It proceeds to complete all active buffers by calling vb2_buffer_done with the new buffer state set to VB2_BUF_STATE_ERROR in that case. This triggers another WARN_ON due to as new state not being VB2_BUF_STATE_QUEUED while the queue is not streaming. Check buffer ownership and complete all active buffers before marking the queue as not streaming to avoid the double WARN_on. Signed-off-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by:
-
Frank Schaefer authored
[media] em28xx: move fields wq_trigger and streaming_started from struct em28xx to struct em28xx_audio Both wq_trigger and stream_started are used only to control the em28xx alsa streaming. They don't belong to em28xx common struct. Signed-off-by:
Frank Schäfer <fschaefer.oss@googlemail.com> Signed-off-by:
-
Frank Schaefer authored
The tuner address is only used by the v4l submodule and at tuner setup and can be obtained from the board data directly (if specified). Signed-off-by:
-
Frank Schaefer authored
The tda9887 chipset is part of the analog tuner. Move it out of em28xx-cards. Also, it is used only one time by the v4l2 sub-module at tuner setup. With that, we can get rid of an additional data inside the em28xx common structure. Signed-off-by:
-
Frank Schaefer authored
Move V4L2-specific frequency cache to struct em28xx_v4l2. Signed-off-by:
-
Frank Schaefer authored
Despite being at the common em28xx struct, those two fields are actually taking into account only the usage inside em28xx v4l2 submodule. So, move them out of the common struct. Signed-off-by:
-
Frank Schaefer authored
Move some temporary capture tracking date to the em28xx_v4l2 struct, as those info are used only by em28xx v4l2 submodule. Signed-off-by:
-
Frank Schaefer authored
Move camera sensor resolution and xtal out of em28xx common struct, as thore are used only by the em28xx v4l2 submodule. Signed-off-by:
-
Frank Schaefer authored
The video progressive data fields belong to analog TV. Move them out of the common em28xx struct. Signed-off-by:
-
Frank Schaefer authored
The analog format struct belongs to analog TV. Move it out of the common em28xx struct. Signed-off-by:
-
Frank Schaefer authored
TV norm is specific to analog TV reception. move it out of the common em28xx struct. Signed-off-by:
-
Frank Schaefer authored
The video input mode and control data also belong only to the analog side. move them to struct em28xx_v4l. Signed-off-by:
-
Frank Schaefer authored
The em28xx scaler data are used only for analog video. Move them to struct em28xx_v4l2. Signed-off-by:
-
Frank Schaefer authored
The video and VBI-specific VB2 queue and mutexes are used only by the v4l2 sub-driver. Move them to the V4L2 struct, preventing wasting memory if this sub-driver is not used. Signed-off-by:
-
Frank Schaefer authored
There are 3 struct video_device at the em28xx common struct, for video, VBI and radio. They all are used only by the V4L2 driver. So, move them to the v4l2-specific struct. Signed-off-by:
-
Frank Schaefer authored
The current clock definition applies only to the V4L2 side of the driver. Move its struct pointer to the v4l2_dev, where it belongs. Signed-off-by:
-
Frank Schaefer authored
Controls are only applicable to V4L2 module. Move the corresponding data structs to the proper place. Signed-off-by:
-
Frank Schaefer authored
That reduces a little bit the memory footprint when em28xx-video is not loaded. Signed-off-by:
-
Frank Schaefer authored
[media] em28xx-video: simplify usage of the pointer to struct v4l2_ctrl_handler in em28xx_v4l2_init() The local var hdl is already pointing to &dev->ctrl_handler. Use it, instead of dereferencing it all the time. Code cleanup. No functional changes. Signed-off-by:
-
Frank Schaefer authored
Just a cleanup. No functional changes. Signed-off-by:
-
Frank Schaefer authored
It is no longer needed since nobody is calling i2c_get_adapdata() anymore. Signed-off-by:
-
Mikhail Domrachev authored
Signed-off-by:
Mikhail Domrachev <mihail.domrychev@comexp.ru> Signed-off-by:
-
Hans Verkuil authored
The message logged by v4l_print_cropcap should be a single line withouti linebreaks, just like all the other v4l_print_<ioctl> functions. Signed-off-by:
-
Vitaly Osipov authored
tcm825x.c: changed printk to pr_info Signed-off-by:
Vitaly Osipov <vitaly.osipov@gmail.com> Signed-off-by:
-
Vitaly Osipov authored
tcm825x.c: fixing ERROR: Macros with complex values should be enclosed in parenthesis Signed-off-by:
-
Ma Haijun authored
The second argument should be physical address rather than virtual address. Signed-off-by:
Ma Haijun <mahaijuns@gmail.com> Signed-off-by:
-
Takashi Iwai authored
When ivtv PCM device is accessed at the state where no firmware is loaded, it oopses like: BUG: unable to handle kernel NULL pointer dereference at 0000000000000050 IP: [<ffffffffa049a881>] try_mailbox.isra.0+0x11/0x50 [ivtv] Call Trace: [<ffffffffa049aa20>] ivtv_api_call+0x160/0x6b0 [ivtv] [<ffffffffa049af86>] ivtv_api+0x16/0x40 [ivtv] [<ffffffffa049b10c>] ivtv_vapi+0xac/0xc0 [ivtv] [<ffffffffa049d40d>] ivtv_start_v4l2_encode_stream+0x19d/0x630 [ivtv] [<ffffffffa0530653>] snd_ivtv_pcm_capture_open+0x173/0x1c0 [ivtv_alsa] [<ffffffffa04526f1>] snd_pcm_open_substream+0x51/0x100 [snd_pcm] [<ffffffffa0452853>] snd_pcm_open+0xb3/0x260 [snd_pcm] [<ffffffffa0452a37>] snd_pcm_capture_open+0x37/0x50 [snd_pcm] [<ffffffffa033f557>] snd_open+0xa7/0x1e0 [snd] [<ffffffff8118a628>] chrdev_open+0x88/0x1d0 [<ffffffff811840be>] do_dentry_open+0x1de/0x270 [<ffffffff81193a73>] do_last+0x1c3/0xec0 [<ffffffff81194826>] path_openat+0xb6/0x670 [<ffffffff81195b65>] do_filp_open+0x35/0x80 [<ffffffff81185449>] do_sys_open+0x129/0x210 [<ffffffff815b782d>] system_call_fastpath+0x1a/0x1f This patch adds the check of firmware at PCM open callback like other open callbacks of this driver. Bugzilla: https://apibugzilla.novell.com/show_bug.cgi?id=875440 Cc: <stable@vger.kernel.org> Signed-off-by:Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Alexander Shiyan authored
This will help to debug driver, allows us to see the full name of the device through /proc/interrupts. CPU0 ... 69: 0 mxc-avic 53 10023000.coda ... Signed-off-by:Alexander Shiyan <shc_work@mail.ru> Acked-by:
-
Lad, Prabhakar authored
this patch adds support to release the buffer by calling vb2_buffer_done(), with state marked as VB2_BUF_STATE_QUEUED if start_streaming() call back fails. Signed-off-by:
Lad, Prabhakar <prabhakar.csengg@gmail.com> Signed-off-by:
-
Daeseok Youn authored
smatch says: drivers/media/usb/s2255/s2255drv.c:2246 s2255_probe() warn: possible memory leak of 'dev' Signed-off-by:
Daeseok Youn <daeseok.youn@gmail.com> Acked-by:
Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by:
-
