- 06 May, 2024 2 commits
-
-
Johannes Berg authored
Given how late we are in the cycle, merge the two fixes from wireless into wireless-next as they don't see that urgent. This way, the wireless tree won't need rebasing later. Signed-off-by:Johannes Berg <johannes.berg@intel.com>
-
https://github.com/pkshih/rtwKalle Valo authored
rtw-next patches for v6.10 Major changes are listed as below rtl8xxxu: - remove rtl8xxxu_ prefix from filename - cleanup includes of header files rtlwifi: - adjust code to share with coming support of rtl8192du rtw89: - complete features of new WiFi 7 chip 8922AE including BT-coexistence and WoWLAN - use BIOS ACPI settings to set TX power and channels
-
- 04 May, 2024 11 commits
-
-
Ping-Ke Shih authored
le32p_replace_bits() only updates partial bits of rate_mask, and GCC warns below. Set initial value to avoid warnings, and prevent random value of missed bits (bit 6 of rate_mask.macid_and_short_gi). In file included from ./include/linux/fortify-string.h:5, from ./include/linux/string.h:369, from ./include/linux/bitmap.h:13, from ./include/linux/cpumask.h:13, from ./include/linux/sched.h:16, from drivers/net/wireless/realtek/rtlwifi/rtl8192d/../wifi.h:9, from drivers/net/wireless/realtek/rtlwifi/rtl8192d/hw_common.c:4: In function 'le32p_replace_bits', inlined from 'rtl92de_update_hal_rate_mask.isra' at drivers/net/wireless/realtek/rtlwifi/rtl8192d/hw_common.c:986:2: ./include/linux/bitfield.h:189:15: warning: 'rate_mask' is used uninitialized [-Wuninitialized] 189 | *p = (*p & ~to(field)) | type##_encode_bits(val, field); \ | ^~ ./include/linux/bitfield.h:196:9: note: in expansion of macro '____MAKE_OP' 196 | ____MAKE_OP(le##size,u##size,cpu_to_le##size,le##size##_to_cpu) \ | ^~~~~~~~~~~ ./include/linux/bitfield.h:201:1: note: in expansion of macro '__MAKE_OP' 201 | __MAKE_OP(32) | ^~~~~~~~~ drivers/net/wireless/realtek/rtlwifi/rtl8192d/hw_common.c: In function 'rtl92de_update_hal_rate_mask.isra': drivers/net/wireless/realtek/rtlwifi/rtl8192d/hw_common.c:863:37: note: 'rate_mask' declared here 863 | struct rtl92d_rate_mask_h2c rate_mask; | ^~~~~~~~~ Compile tested only. Fixes: 014bba73 ("wifi: rtlwifi: Adjust rtl8192d-common for USB") Cc: Bitterblue Smith <rtl8821cerfe2@gmail.com> Signed-off-by:Ping-Ke Shih <pkshih@realtek.com> Link: https://msgid.link/20240504111916.31445-1-pkshih@realtek.com
-
Gustavo A. R. Silva authored
Wflex-array-member-not-at-end is coming in GCC-14, and we are getting ready to enable it globally. So, remove unused structs and fix the following -Wflex-array-member-not-at-end warnings: drivers/net/wireless/realtek/rtlwifi/btcoexist/../wifi.h:1063:30: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end] drivers/net/wireless/realtek/rtlwifi/rtl8188ee/../wifi.h:1063:30: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end] drivers/net/wireless/realtek/rtlwifi/rtl8192c/../wifi.h:1063:30: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end] drivers/net/wireless/realtek/rtlwifi/rtl8192ce/../wifi.h:1063:30: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end] drivers/net/wireless/realtek/rtlwifi/rtl8192cu/../wifi.h:1063:30: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end] drivers/net/wireless/realtek/rtlwifi/rtl8192de/../wifi.h:1063:30: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end] drivers/net/wireless/realtek/rtlwifi/rtl8192ee/../wifi.h:1063:30: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end] drivers/net/wireless/realtek/rtlwifi/rtl8192se/../wifi.h:1063:30: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end] drivers/net/wireless/realtek/rtlwifi/rtl8723ae/../wifi.h:1063:30: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end] drivers/net/wireless/realtek/rtlwifi/rtl8723be/../wifi.h:1063:30: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end] drivers/net/wireless/realtek/rtlwifi/rtl8723com/../wifi.h:1063:30: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end] drivers/net/wireless/realtek/rtlwifi/rtl8821ae/../wifi.h:1063:30: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end] drivers/net/wireless/realtek/rtlwifi/wifi.h:1063:30: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end] Signed-off-by:
Gustavo A. R. Silva <gustavoars@kernel.org> Reviewed-by:
Kees Cook <keescook@chromium.org> Acked-by:
-
Ping-Ke Shih authored
aSIFSTime is 10us for 2GHz band and 16us for 5GHz and 6GHz bands. Originally, it doesn't consider 6GHz band and use wrong value, so correct it accordingly. Cc: stable@vger.kernel.org Signed-off-by:
-
Chin-Yen Lee authored
Add H2C command and offload template packet to allow firmware send ARP response in WoWLAN mode. Then, firmware in WoWLAN mode can interactive with peer that issue ARP request to query MAC address. Signed-off-by:
Chin-Yen Lee <timlee@realtek.com> Signed-off-by:
-
Chih-Kang Chang authored
When using the WEP cipher, we need to add the address cam type as all unicast mode to let firmware to work. Although WEP only set GTK in mac80211, but we need to set both PTK and GTK information to firmware. Signed-off-by:
Chih-Kang Chang <gary.chang@realtek.com> Signed-off-by:
-
Chih-Kang Chang authored
Once we connect to AP with 802.11w enabled, IGTK rekey happen during GTK happen. We get IGTK IPN from mac80211 and set to firmware, and get latest IGTK IPN from AOAC report then update to mac80211 after resume. When rekey happen, also update new IGTK key info to mac80211. Furthermore, We construct SA query reply packet to firmware. If firmware received SA query request from AP can transmit reply back when suspend. Signed-off-by:
-
Chih-Kang Chang authored
When resume we parse AOAC report from firmware using H2C and C2H registers before enable interrupt, then update PTK RX PN and GTK RX PN. After enable interrupt, we parse AOAC report using H2C and C2H commands, then update PTK TX PN and update new GTK key info if GTK rekey during suspend. Furthermore, We update pattern match index if wakeup by pattern. Signed-off-by:
-
Chih-Kang Chang authored
Add PTK TRX IV, GTK RX IV, key encryption algorithm to H2C command to enable GTK rekey feature. Signed-off-by:
-
Chih-Kang Chang authored
We construct EAPoL packet with various encryption method, and download to firmware. Also we add Key Encryption Key (KEK) and Key Confirmation Key (KCK) to H2C command. Once firmware received EAPoL group rekey packet(1/2) can TX EAPoL group rekey packet(2/2) when suspend. Signed-off-by:
-
Chih-Kang Chang authored
This H2C command is used to set WoWLAN global config, and we correct the H2C format by enlarging the H2C size to fill GTK and PTK info. This fix is compatible with old firmware. Signed-off-by:
-
Chih-Kang Chang authored
This H2C command set key information into security CAM including key index, entry index and valid map. No logic is changed. Signed-off-by:
-
- 03 May, 2024 13 commits
-
-
Chih-Kang Chang authored
Get the PTK and PTK TRX PN value and transfer to IV value, these values will used by firmware to generate packets with correct IV value. Signed-off-by:
-
Chih-Kang Chang authored
Need Auth Key Management(AKM) to let firmware to generate appropriate EAPoL packet for GTK rekey. The AKM is present in the association request RSN IE to indicate which cipher that station selected. Signed-off-by:
-
Chih-Kang Chang authored
After enabling packet offload, the TX will be stuck after resume from WoWLAN mode. And the 8852c gets error messages like rtw89_8852ce 0000:04:00.0: No busy txwd pages available rtw89_8852ce 0000:04:00.0: queue 0 txwd 100 is not idle rtw89_8852ce 0000:04:00.0: queue 0 txwd 101 is not idle rtw89_8852ce 0000:04:00.0: queue 0 txwd 102 is not idle rtw89_8852ce 0000:04:00.0: queue 0 txwd 103 is not idle If suspend/resume many times that firmware will download failed and disconnection. To fix these issues, We removed the rtw89_hci_disable_intr() and rtw89_hci_enable_intr() during rtw89_wow_swap_fw() to prevent add packet offload can't receive c2h back due to interrupt disable. Only 8852C and 8922A needs to disable interrupt before downloading fw. Furthermore, we avoid using low power HCI mode on WoWLAN mode, to prevent interrupt enabled, then get interrupt and calculate RXBD mismatched due to software RXBD index already reset but hardware RXBD index not yet. Fixes: 5c12bb66 ("wifi: rtw89: refine packet offload flow") Signed-off-by:
-
Chin-Yen Lee authored
802.11be WiFi chips need a RFK (RF calibration) notify H2C command after downloading WoWLAN firmware to make sure RF TX/RX work fine when leaving power save mode, so add it to correct RF TX/RX in WoWLAN mode. Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/athKalle Valo authored
ath.git patches for v6.10 ath12k * debugfs support * dfs_simulate_radar debugfs file * disable Wireless Extensions * suspend and hibernation support * ACPI support * refactoring in preparation of multi-link support ath11k * support hibernation (required changes in qrtr and MHI subsystems) * ieee80211-freq-limit Device Tree property support ath10k * firmware-name Device Tree property support
-
https://github.com/nbd168/wirelessKalle Valo authored
mt76 patches for 6.10 - fixes - mt7603 stability improvements - mt7921 LED control - mt7925 EHT radiotap support
-
Aditya Kumar Singh authored
Advertise support for BSS color and then once the countdown reaches 0, call color change finish. Signed-off-by:
Aditya Kumar Singh <quic_adisi@quicinc.com> Link: https://msgid.link/20240422053412.2024075-8-quic_adisi@quicinc.comSigned-off-by:
-
Aditya Kumar Singh authored
In order to support color change with MLO, handle the link ID now passed from cfg80211, adjust the code to do everything per link and call the notifications to cfg80211 correctly. Signed-off-by:
-
Aditya Kumar Singh authored
Currently, during color change, no link id information is passed down. In order to support color change during Multi Link Operation, it is required to pass link id as well. Additionally, update notification APIs to allow drivers/mac80211 to pass the link ID. Signed-off-by:
-
Xin Deng authored
wdev->valid_links is not cleared when upper layer disconnect from a wdev->AP MLD. It has been observed that this would prevent offchannel operations like remain-on-channel which would be needed for user space operations with Public Action frame. Clear the wdev->valid_links when STA disconnects. Signed-off-by:
Xin Deng <quic_deng@quicinc.com> Link: https://msgid.link/20240426092501.8592-1-quic_deng@quicinc.comSigned-off-by:
-
Breno Leitao authored
struct net_device shouldn't be embedded into any structure, instead, the owner should use the priv space to embed their state into net_device. Embedding net_device into structures prohibits the usage of flexible arrays in the net_device structure. For more details, see the discussion at [1]. Un-embed the net_device from struct iwl_trans_pcie by converting it into a pointer. Then use the leverage alloc_netdev() to allocate the net_device object at iwl_trans_pcie_alloc. The private data of net_device becomes a pointer for the struct iwl_trans_pcie, so, it is easy to get back to the iwl_trans_pcie parent given the net_device object. [1] https://lore.kernel.org/all/20240229225910.79e224cf@kernel.org/Reviewed-by:
Breno Leitao <leitao@debian.org> Link: https://msgid.link/20240501165417.3406039-1-leitao@debian.orgSigned-off-by:
-
Kees Cook authored
Before request->channels[] can be used, request->n_channels must be set. Additionally, address calculations for memory after the "channels" array need to be calculated from the allocation base ("request") rather than via the first "out of bounds" index of "channels", otherwise run-time bounds checking will throw a warning. Reported-by:Nathan Chancellor <nathan@kernel.org> Fixes: e3eac9f3 ("wifi: cfg80211: Annotate struct cfg80211_scan_request with __counted_by") Signed-off-by:
-
Ben Greear authored
This appears to work around a deadlock regression that came in with the LED merge in 6.9. The deadlock happens on my system with 24 iwlwifi radios, so maybe it something like all worker threads are busy and some work that needs to complete cannot complete. Link: https://lore.kernel.org/linux-kernel/20240411070718.GD6194@google.com/ Fixes: f5c31bcf ("Merge tag 'leds-next-6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds") Signed-off-by:
Ben Greear <greearb@candelatech.com> Link: https://msgid.link/20240430234212.2132958-1-greearb@candelatech.com [also remove unnecessary "load_module" var and now-wrong comment] Signed-off-by:
-
- 02 May, 2024 14 commits
-
-
Felix Fietkau authored
It is supported by all drivers Signed-off-by:Felix Fietkau <nbd@nbd.name>
-
Deren Wu authored
Add IEEE80211_RADIOTAP_EHT and IEEE80211_RADIOTAP_EHT_USIG radiotap to fill in EHT information, such as MCS, NSS, GI and bandwidth. Co-developed-by:
Ming Yen Hsieh <mingyen.hsieh@mediatek.com> Signed-off-by:
Deren Wu <deren.wu@mediatek.com> Signed-off-by:
-
Hao Zhang authored
Introduce wifi LED switch control, add flow to Control a wifi gpio pin based on the status of WIFI radio, if the pin is connected to an LED, the LED will indicate the status of the WiFi radio. Signed-off-by:
Hao Zhang <hao.zhang@mediatek.com> Co-developed-by:
Quan Zhou <quan.zhou@mediatek.com> Signed-off-by:
Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by:
-
Michael-CY Lee authored
The firmware support for management frame protection has limitations: - do not support cipher BIP-GMAC-128 and BIP-GMAC-256 - support cipher BIP-CMAC-128 and BIP-CMAC-256, except action frame with action type 'not robust'. Therefore, to simplify the logic, do not set the IGTK to firmware and let the encryption of management frames be handled by upper layer. Signed-off-by:
Michael-CY Lee <michael-cy.lee@mediatek.com> Signed-off-by:
Shayne Chen <shayne.chen@mediatek.com> Signed-off-by:
-
Rong Yan authored
The implementation amounts to setting the driver flag IEEE80211_VIF_SUPPORTS_CQM_RSSI, and then providing mechanisms for continuously updating enough information to be able to provide notifications to userspace when RSSI drops below a certain threshold Signed-off-by:
Rong Yan <rong.yan@mediatek.com> Signed-off-by:
-
Felix Fietkau authored
Reduces size by avoiding duplicates Signed-off-by: -
Felix Fietkau authored
This is expected by the firmware of older chipsets as well, though it may not have been as strongly required as on mt799x Fixes: 098428c4 ("wifi: mt76: connac: set correct muar_idx for mt799x chipsets") Signed-off-by:
-
StanleyYP Wang authored
Check if background radar is enabled or not before manually triggering it, and also add more checks in radar detected event. Signed-off-by:
StanleyYP Wang <StanleyYP.Wang@mediatek.com> Signed-off-by:
-
Howard Hsu authored
For mt7992 chipsets, critical packet mode should be properly configured to let the HW SDO module correctly fill the AC queue in TX descriptors of some higher priority packets such as ARP and ICMP. Without this patch, HW queues may hang when running MU traffic. Signed-off-by:
Howard Hsu <howard-yh.hsu@mediatek.com> Signed-off-by:
-
Howard Hsu authored
Without this commit, reading chip temperature will cause memory leakage. Fixes: 6879b2e9 ("wifi: mt76: mt7996: add thermal sensor device support") Reported-by:
Ryder Lee <ryder.lee@mediatek.com> Signed-off-by:
-
Henry Yen authored
Do not add UNI_BSS_INFO_11V_MBSSID tag when bssid_indicator is not set to avoid abnormal beaconing behavior in non-11v MBSS scenario. Signed-off-by:
Henry Yen <henry.yen@mediatek.com> Signed-off-by:
-
Howard Hsu authored
For mt7996 chipsets, the HW CSO module can help to identify TCP traffic, which assists the firmware in adjusting algorithms to improve overall performance. Signed-off-by:
-
Peter Chiu authored
Set RCPI values in mt7996_mcu_sta_rate_ctrl_tlv(), which can make the FW rate control algorithm be initialized with a better MCS selection table. Signed-off-by:
Peter Chiu <chui-hao.chiu@mediatek.com> Signed-off-by:
-
Shayne Chen authored
Set peer address and aid for the BMC wtbl of station interface. For some functions such as parsing MU_EDCA parameters from beacon, firmware will need the peer address to do correct parsing. Without this patch, MU uplink traffic would get suffered. Reported-by:
-
