fdo#92761
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Each GPCCS unit was reading the mask from GPC0, which causes problems on
boards where some GPCs are missing PPCs.

Part of the fix for fdo#92761.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

There's a few places where we need to access a GPC register from ucode,
but outside of the falcon's io address space.  To do this we need to
calculate the offset based on which GPC we're executing on.

This used to be done manually, but we've since found a "base" offset
that can be added by the hardware.  To use this, an extra bit needs to
be set in the register address, which is what this macro achieves.

There should be no functional change from this commit.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Fixes detection of a failed attempt at fetching the entire ROM image
in one-shot (a violation of the spec, that works a lot of the time).

Tested on a HP Zbook 15 G2.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

No locking is required for the traversal of this list, as it only
happens during suspend/resume where nothing else can be executing.

Fixes some of the issues noticed during parallel piglit runs.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

fdo#70354 - comment #88.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

this is needed for my gpu
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

USIF already takes the client mutex, but will need access to ABI16 data
in order to provide some limited interoperability.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91557Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=70354#c75Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

This patch uses an approach closer to the nvidia driver to configure
both PLLs for high gddr5 memory clocks (usually above 2400MHz)

Previously nouveau used the one PLL as it was used for the lower clocks
and just adjusted the second PLL to get as close as possible to the
requested clock.  This means for my card, that I got a 4050 MHz clock
although 4008 MHz was requested.

Now the driver iterates over a list of PLL configuration also used by
the nvidia driver and then adjust the second PLL to get near the
requested clock.  Also it hold to some restriction I found while
analyzing the PLL configurations

This won't fix all gddr5 high clock issues itself, but it should be
fine on hybrid gpu systems as found on many laptops these days.  Also
switching while normal desktop usage should be a lot more stable than
before.

v2: move the pll code into ramgk104
Signed-off-by: Karol Herbst <nouveau@karolherbst.de>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Your milage may vary, as it's only been tested on a single G94 and one G96.
Signed-off-by: Roy Spliet <rspliet@eclipso.eu>
Tested-by: Pierre Moreau <pierre.morrow@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Avoids waiting for VBLANKS that never arrive on headless or otherwise
unconventional set-ups. Strategy taken from MEMX.
Signed-off-by: Roy Spliet <rspliet@eclipso.eu>
Tested-by: Pierre Moreau <pierre.morrow@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

10053c is not even read on some cards, and I have no idea exactly what the
criteria are. Likely NVIDIA pre-scans the VBIOS and in their driver disables
all features that are never used. The practical effect should be the same
as this implementation though.
Signed-off-by: Roy Spliet <rspliet@eclipso.eu>
Tested-by: Pierre Moreau <pierre.morrow@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Like Pierre's G94. We might want to structure Kepler similarly in a follow-up.
Signed-off-by: Roy Spliet <rspliet@eclipso.eu>
Tested-by: Pierre Moreau <pierre.morrow@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Does not seem to be necessary for NVA0, hence untested by me.
Signed-off-by: Roy Spliet <rspliet@eclipso.eu>
Tested-by: Pierre Moreau <pierre.morrow@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Seems to be mostly equal to DDR3 on < GT218, should improve stability for
DDR2 reclocks.
Signed-off-by: Roy Spliet <rspliet@eclipso.eu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Signed-off-by: Roy Spliet <rspliet@eclipso.eu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

In preparation of changing FBVDDQ, as observed on at least one GDDR3 card.
While at it, adhere to func.log[1] properly for consistency.
Signed-off-by: Roy Spliet <rspliet@eclipso.eu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Signed-off-by: Roy Spliet <rspliet@eclipso.eu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

If the hardware supports extended tag field (8-bit ones), then enable it.

This is usually done by the VBIOS, but not on some MBPs (see fdo#86537).

In case extended tag field is not supported, 5-bit tag field is used which
limits the possible number of requests to 32. Apparently bits 7:0 of
0x08841c stores some number of outstanding requests, so cap it to 32 if
extended tag is unsupported.

Fixes: fdo#86537

v2: Restrict changes to chipsets >= 0x84
v3:
  * Add nvkm_pci_mask to pci.h
  * Mask bit 8 before setting it
v4:
  * Rename `add` argument of nvkm_pci_mask to `value`
  * Move code from nvkm_pci_init to g84_pci_init and remove PCIe and chipset
    checks
v5:
  * Rebase code on latest PCI structure
  * Restore PCIe check
  * Fix namings in nvkm_pci_mask
  * Rephrase part of the commit message
Signed-off-by: Pierre Moreau <pierre.morrow@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

These nvkm_object_func structures are never modified.  All other
nvkm_object_func structures are declared as const.

Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

GF110+ supports both the A and B compute classes, make sure to accept
both.
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

NVIDIA provided the documentation for mp error 0x10, INVALID_ADDR_SPACE,
which apparently happens when trying to use an atomic operation on
local or shared memory (instead of global memory).
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

If pm_runtime_get_sync() we were going to "out" but we missed freeing
vma.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

coverity.com reported that memset was using a buffer of size 0, on
checking the code it turned out that the function was not being used. So
remove it.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Reviewed-by: Samuel Pitoiset <samuel.pitoiset@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Reported to be needed as per fdo#70354 comment #61.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Not 100% confirmed, but seems to match from the few boards I've looked
at so far.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Was not able to obtain a trace of NVRM due to kernel version annoyances,
however, experimentally confirmed that the WAR we use on NV50/G8x boards
works here too.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

An upcoming patch will implement functionality that we don't use on any
NV40 chipset.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

An upcoming patch will implement functionality that we don't use on the
original NV50.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Increase clock timeout of some unknown engines in order to avoid failure
at high gpcclk rate.

This fixes IBUS read faults on my GF119 when reclocking is manually
enabled. Note that memory reclocking is completely broken and NvMemExec
has to be disabled to allow core clock reclocking only.
Signed-off-by: Samuel Pitoiset <samuel.pitoiset@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

I got confirmation that we can read and change the voltage with the same code.
The divider is also computed correctly on the gm204 we got our hands on.

Thanks to Yoshimo on IRC for executing the tests on his gm204!
Signed-off-by: Martin Peres <martin.peres@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Let's ignore the other desktop Maxwells until I get my hands on one and confirm
that we still can change the voltage.
Signed-off-by: Martin Peres <martin.peres@free.fr>

Most Keplers actually use the GPIO-based voltage management instead of the new
PWM-based one. Use the GPIO mode as a fallback as it already gracefully handles
the case where no GPIOs exist.

All the Maxwells seem to use the PWM method though.

v2:
 - Do not forget to commit the PWM configuration change!
Signed-off-by: Martin Peres <martin.peres@free.fr>

This patch is not ideal but it definitely beats a rewrite of the current
interface and is very self-contained.
Signed-off-by: Martin Peres <martin.peres@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>