- 01 Mar, 2016 40 commits
-
-
Sergei Shtylyov authored
of_mdiobus_register() declares the 'paddr' variable to hold the result of the of_get_property() but only uses it once after that while the function can be called directly from the *if* statement. Remove that variable and switch to calling of_find_property() instead since we don't care about the "reg" property's value anyway... Signed-off-by:
Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Yuval Mintz says: ==================== qed: Attention support patch series Until now we've only enabled attention generation for the sake of management firmware indications [required for link notifications]. This series enables [almost] all the attention sources of the HW, currently for the sake of logging information relating to issues experienced by HW. In future, infrastructure laid here would also be used for the sake of the recovery process. The first patch in the series is a semantic alignemnt of the code. The later 3 patches incremently create said infrastructure and enrich the logged information. Notice #3 contains quite a bit of structures [consisting of ~1K lines] that will eventually be removed and incorporated in the binary fw file. ==================== Signed-off-by: -
Yuval Mintz authored
This patch utilizes the attention infrastructure to log additional information that relates only to specific HW blocks. For some of those HW blocks, it also stops automatically disabling the attention generation as the attention is considered benign and thus should only be logged; No fear of it flooding the system. Signed-off-by:
Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by:
-
Yuval Mintz authored
Each HW block contains common information about attention reasons, raising a bit for each one of the different sub-reasons that caused it to raise an attention. This patch extends the infrastructure by allowing logging of the various reasons causing the HW blocks to generate an attention. Signed-off-by:
-
Yuval Mintz authored
HW is capable of generating attentnions for a multitude of reasons, but current driver is enabling attention generation only for management firmware [required for link notifications]. This patch enables almost all of the possible reasons for HW attentions, logging the HW block generating the attention and preventing further attentions from that source [to prevent possible attention flood]. It also lays the infrastructure for additional exploration of the various attentions. Signed-off-by:
-
Yuval Mintz authored
Signed-off-by:
-
WANG Cong authored
After commit 52bd2d62 ("net: better skb->sender_cpu and skb->napi_id cohabitation") skb_sender_cpu_clear() becomes empty and can be removed. Cc: Eric Dumazet <edumazet@google.com> Signed-off-by:
Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by:
-
David S. Miller authored
Saeed Mahameed says: ==================== mlx5 driver updates This series includes some bug fixes and updates for the mlx5 core and ethernet driver. From Gal, two fixes that protects the update CQ moderation flows when it is not allowed. From Moshe, two fixes for the core and ethernet driver in non-cached(NC) and write combining(WC) buffers mappings, which prevents the driver from double memory mappings. From Or, reduce the firmware command completion timeout. From Tariq, several small trivial fixes. Changes from v0: - "Fix global UAR mapping" commit messages updated to explain ARCH_HAS_IOREMAP_WC usage. - rebased to commit 8d3f2806 'Merge branch ethtool-ksettings' Changes from v1: - Removed ARCH_HAS_IOREMAP_WC config flag from "Fix global UAR mapping" commit, as it was not accurate to use it. - Squashed "Fix global UAR mapping" and "net/mlx5: Avoid double mapping of io mapped memory" - Added more info for "Fix global UAR mapping" in commit message Changes from v2: - None. resubmission per Dave's request due to two parallel submissions to mlx5 driver. ==================== Signed-off-by:
-
Moshe Lazer authored
Avoid double mapping of io mapped memory, Device page may be mapped to non-cached(NC) or to write-combining(WC). The code before this fix tries to map it both to WC and NC contrary to what stated in Intel's software developer manual. Here we remove the global WC mapping of all UARS "dev->priv.bf_mapping", since UAR mapping should be decided per UAR (e.g we want different mappings for EQs, CQs vs QPs). Caller will now have to choose whether to map via write-combining API or not. mlx5e SQs will choose write-combining in order to perform BlueFlame writes. Fixes: 88a85f99 ('TX latency optimization to save DMA reads') Signed-off-by:
Moshe Lazer <moshel@mellanox.com> Reviewed-by:
Achiad Shochat <achiad@mellanox.com> Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com> Signed-off-by:
-
Or Gerlitz authored
The command timeout is terribly long, whole two hours. Make it 60s so if things do go wrong, the user gets feedback in relatively short time, so they can take corrective actions and/or investigate using tools and such. Fixes: e126ba97 ('mlx5: Add driver for Mellanox Connect-IB adapters') Signed-off-by:
Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by:
Leon Romanovsky <leonro@mellanox.com> Signed-off-by:
-
Gal Pressman authored
Calling mlx5e_set_coalesce while the interface is down will result in modifying CQs that don't exist. Fixes: f62b8bb8 ('net/mlx5: Extend mlx5_core to support ConnectX-4 Ethernet functionality') Signed-off-by:
Gal Pressman <galp@mellanox.com> Signed-off-by:
-
Gal Pressman authored
If CQ moderation is not supported by the device, print a warning on netdevice load, and return error when trying to modify/query cq moderation via ethtool. Fixes: f62b8bb8 ('net/mlx5: Extend mlx5_core to support ConnectX-4 Ethernet functionality') Signed-off-by:
-
Tariq Toukan authored
By its role, there is no need to set all the other parameters for the drop RQ. Signed-off-by:
Tariq Toukan <tariqt@mellanox.com> Signed-off-by:
-
Tariq Toukan authored
For data cache locality considerations, we moved the nop and csum_offload_inner within sq_stats struct as they are more commonly accessed in xmit path. Signed-off-by:
-
Tariq Toukan authored
Instead of the pair (channel, tc), we now use a single number that goes over all tx queues of a TC, for all TCs. Signed-off-by:
-
Tariq Toukan authored
More proper to declare carrier state UP only after the channels are ready for traffic. Signed-off-by:
-
Tariq Toukan authored
We only need to flush the irq handler to make sure it does not queue a work into the global work queue after we start to flush it. So using synchronize_irq() is more appropriate than a spin lock. Signed-off-by:
-
David Ahern authored
Commit f1705ec1 allows IPv6 addresses to be retained on a link down. The address can have a cached host route which can point to the wrong FIB table if the L3 enslavement is changed (e.g., route can point to local table instead of VRF table if device is added to an L3 domain). On link up check the table of the cached host route against the FIB table associated with the device and correct if needed. Signed-off-by:
David Ahern <dsa@cumulusnetworks.com> Signed-off-by:
-
David S. Miller authored
Deepa Dinamani says: ==================== Convert network timestamps to be y2038 safe Introduction: The series is aimed at transitioning network timestamps to being y2038 safe. All patches can be reviewed and merged independently. Socket timestamps and ioctl calls will be handled separately. Thanks to Arnd Bergmann for discussing solution options with me. Solution: Data type struct timespec is not y2038 safe. Replace timespec with struct timespec64 which is y2038 safe. Changes v1 -> v2: Move and rename inet_current_time() as discussed Squash patches 1 and 2 Reword commit text for patch 2/3 Carry over review tags ==================== Signed-off-by: -
Deepa Dinamani authored
SCTP probe log timestamps use struct timespec which is not y2038 safe. Use struct timespec64 which is 2038 safe instead. Use monotonic time instead of real time as only time differences are logged. Signed-off-by:
Deepa Dinamani <deepa.kernel@gmail.com> Reviewed-by:
Arnd Bergmann <arnd@arndb.de> Acked-by:
Neil Horman <nhorman@tuxdriver.com> Cc: Vlad Yasevich <vyasevich@gmail.com> Cc: Neil Horman <nhorman@tuxdriver.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: linux-sctp@vger.kernel.org Signed-off-by:
-
Deepa Dinamani authored
TCP probe log timestamps use struct timespec which is not y2038 safe. Even though timespec might be good enough here as it is used to represent delta time, the plan is to get rid of all uses of timespec in the kernel. Replace with struct timespec64 which is y2038 safe. Prints still use unsigned long format and type. Signed-off-by:
YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by:
-
Deepa Dinamani authored
ICMP timestamp messages and IP source route options require timestamps to be in milliseconds modulo 24 hours from midnight UT format. Add inet_current_timestamp() function to support this. The function returns the required timestamp in network byte order. Timestamp calculation is also changed to call ktime_get_real_ts64() which uses struct timespec64. struct timespec64 is y2038 safe. Previously it called getnstimeofday() which uses struct timespec. struct timespec is not y2038 safe. Signed-off-by:
-
David S. Miller authored
Jamal Hadi Salim says: ==================== net_sched: Add support for IFE action As agreed at netconf in Seville, here's the patch finally (1 year was just too long to wait for an ethertype. Now we are just going have the user configure one). Described in netdev01 paper: "Distributing Linux Traffic Control Classifier-Action Subsystem" Authors: Jamal Hadi Salim and Damascene M. Joachimpillai The original motivation and deployment of this work was to horizontally scale packet processing at scope of a chasis or rack. This means one could take a tc policy and split it across machines connected over L2. The paper refers to this as "pipeline stage indexing". Other use cases which evolved out of the original intent include but are not limited to carrying OAM information, carrying exception handling metadata, carrying programmed authentication and authorization information, encapsulating programmed compliance information, service IDs etc. Read the referenced paper for more details. The architecture allows for incremental updates for new metadatum support to cover different use cases. This patch set includes support for basic skb metadatum. Followup patches will have more examples of metadata and other features. v4 changes: Integrate more feedback from Cong v3 changes: Integrate with the new namespace changes Remove skbhash and queue mapping metadata (but keep their claim for ids) Integrate feedback from Cong Integrate feedback from Daniel v2 changes: Remove module option for an upper bound of metadata Integrate feedback from Cong Integrate feedback from Daniel ==================== Signed-off-by: -
Jamal Hadi Salim authored
Example usage: Set the skb priority using skbedit then allow it to be encoded sudo tc qdisc add dev $ETH root handle 1: prio sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \ u32 match ip protocol 1 0xff flowid 1:2 \ action skbedit prio 17 \ action ife encode \ allow prio \ dst 02:15:15:15:15:15 Note: You dont need the skbedit action if you are already encoding the skb priority earlier. A zero skb priority will not be sent Alternative hard code static priority of decimal 33 (unlike skbedit) then mark of 0x12 every time the filter matches sudo $TC filter add dev $ETH parent 1: protocol ip prio 10 \ u32 match ip protocol 1 0xff flowid 1:2 \ action ife encode \ type 0xDEAD \ use prio 33 \ use mark 0x12 \ dst 02:15:15:15:15:15 Signed-off-by:Jamal Hadi Salim <jhs@mojatatu.com> Acked-by:
-
Jamal Hadi Salim authored
Example usage: Set the skb using skbedit then allow it to be encoded sudo tc qdisc add dev $ETH root handle 1: prio sudo tc filter add dev $ETH parent 1: protocol ip prio 10 \ u32 match ip protocol 1 0xff flowid 1:2 \ action skbedit mark 17 \ action ife encode \ allow mark \ dst 02:15:15:15:15:15 Note: You dont need the skbedit action if you are already encoding the skb mark earlier. A zero skb mark, when seen, will not be encoded. Alternative hard code static mark of 0x12 every time the filter matches sudo $TC filter add dev $ETH parent 1: protocol ip prio 10 \ u32 match ip protocol 1 0xff flowid 1:2 \ action ife encode \ type 0xDEAD \ use mark 0x12 \ dst 02:15:15:15:15:15 Signed-off-by:
-
Jamal Hadi Salim authored
This action allows for a sending side to encapsulate arbitrary metadata which is decapsulated by the receiving end. The sender runs in encoding mode and the receiver in decode mode. Both sender and receiver must specify the same ethertype. At some point we hope to have a registered ethertype and we'll then provide a default so the user doesnt have to specify it. For now we enforce the user specify it. Lets show example usage where we encode icmp from a sender towards a receiver with an skbmark of 17; both sender and receiver use ethertype of 0xdead to interop. YYYY: Lets start with Receiver-side policy config: xxx: add an ingress qdisc sudo tc qdisc add dev $ETH ingress xxx: any packets with ethertype 0xdead will be subjected to ife decoding xxx: we then restart the classification so we can match on icmp at prio 3 sudo $TC filter add dev $ETH parent ffff: prio 2 protocol 0xdead \ u32 match u32 0 0 flowid 1:1 \ action ife decode reclassify xxx: on restarting the classification from above if it was an icmp xxx: packet, then match it here and continue to the next rule at prio 4 xxx: which will match based on skb mark of 17 sudo tc filter add dev $ETH parent ffff: prio 3 protocol ip \ u32 match ip protocol 1 0xff flowid 1:1 \ action continue xxx: match on skbmark of 0x11 (decimal 17) and accept sudo tc filter add dev $ETH parent ffff: prio 4 protocol ip \ handle 0x11 fw flowid 1:1 \ action ok xxx: Lets show the decoding policy sudo tc -s filter ls dev $ETH parent ffff: protocol 0xdead xxx: filter pref 2 u32 filter pref 2 u32 fh 800: ht divisor 1 filter pref 2 u32 fh 800::800 order 2048 key ht 800 bkt 0 flowid 1:1 (rule hit 0 success 0) match 00000000/00000000 at 0 (success 0 ) action order 1: ife decode action reclassify index 1 ref 1 bind 1 installed 14 sec used 14 sec type: 0x0 Metadata: allow mark allow hash allow prio allow qmap Action statistics: Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0) backlog 0b 0p requeues 0 xxx: Observe that above lists all metadatum it can decode. Typically these submodules will already be compiled into a monolithic kernel or loaded as modules YYYY: Lets show the sender side now .. xxx: Add an egress qdisc on the sender netdev sudo tc qdisc add dev $ETH root handle 1: prio xxx: xxx: Match all icmp packets to 192.168.122.237/24, then xxx: tag the packet with skb mark of decimal 17, then xxx: Encode it with: xxx: ethertype 0xdead xxx: add skb->mark to whitelist of metadatum to send xxx: rewrite target dst MAC address to 02:15:15:15:15:15 xxx: sudo $TC filter add dev $ETH parent 1: protocol ip prio 10 u32 \ match ip dst 192.168.122.237/24 \ match ip protocol 1 0xff \ flowid 1:2 \ action skbedit mark 17 \ action ife encode \ type 0xDEAD \ allow mark \ dst 02:15:15:15:15:15 xxx: Lets show the encoding policy sudo tc -s filter ls dev $ETH parent 1: protocol ip xxx: filter pref 10 u32 filter pref 10 u32 fh 800: ht divisor 1 filter pref 10 u32 fh 800::800 order 2048 key ht 800 bkt 0 flowid 1:2 (rule hit 0 success 0) match c0a87aed/ffffffff at 16 (success 0 ) match 00010000/00ff0000 at 8 (success 0 ) action order 1: skbedit mark 17 index 6 ref 1 bind 1 Action statistics: Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0) backlog 0b 0p requeues 0 action order 2: ife encode action pipe index 3 ref 1 bind 1 dst MAC: 02:15:15:15:15:15 type: 0xDEAD Metadata: allow mark Action statistics: Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0) backlog 0b 0p requeues 0 xxx: test by sending ping from sender to destination Signed-off-by: -
David S. Miller authored
Merge tag 'mac80211-next-for-davem-2016-02-26' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next Johannes Berg says: ==================== Here's another round of updates for -next: * big A-MSDU RX performance improvement (avoid linearize of paged RX) * rfkill changes: cleanups, documentation, platform properties * basic PBSS support in cfg80211 * MU-MIMO action frame processing support * BlockAck reordering & duplicate detection offload support * various cleanups & little fixes ==================== Signed-off-by:
-
David S. Miller authored
Nikolay Aleksandrov says: ==================== bridge: mcast: add support for temp router port This set adds support for temporary router port which doesn't depend only on the incoming queries. It can be refreshed by setting multicast_router to the same value (3). The first two patches are minor changes that prepare the code for the third which adds this new type of router port. In order to be able to dump its information the mdb router port format is changed in patch 04 and extended similar to how mdb entries format was done recently. The related iproute2 changes will be posted if this is accepted. v2: set val first and adjust router type later in patch 01, patch 03 was split in 2 ==================== Signed-off-by: -
Nikolay Aleksandrov authored
Allow for more multicast router port information to be dumped such as timer and type attributes. For that that purpose we need to extend the MDBA_ROUTER_PORT attribute similar to how it was done for the mdb entries recently. The new format is thus: [MDBA_ROUTER_PORT] = { <- nested attribute u32 ifindex <- router port ifindex for user-space compatibility [MDBA_ROUTER_PATTR attributes] } This way it remains compatible with older users (they'll simply retrieve the u32 in the beginning) and new users can parse the remaining attributes. It would also allow to add future extensions to the router port without breaking compatibility. Signed-off-by:Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by:
-
Nikolay Aleksandrov authored
Add support for a temporary router port which doesn't depend only on the incoming query. It can be refreshed if set to the same value, which is a no-op for the rest. Signed-off-by:
-
Nikolay Aleksandrov authored
This is needed for the upcoming temporary port router. There's no point to go through the logic if the value is the same. Signed-off-by:
-
Nikolay Aleksandrov authored
Using raw values makes it difficult to extend and also understand the code, give them names and do explicit per-option manipulation in br_multicast_set_port_router. Signed-off-by:
-
David S. Miller authored
Vivien Didelot says: ==================== net: dsa: mv88e6xxx: implement VLAN filtering This patchset fixes hardware bridging for non 802.1Q aware systems. The mv88e6xxx DSA driver currently depends on CONFIG_VLAN_8021Q and CONFIG_BRIDGE_VLAN_FILTERING enabled for correct bridging between switch ports. Patch 1/9 adds support for the VLAN filtering switchdev attribute in DSA. Patchs 2/9 and 3/9 add helper functions for the following patches. Patchs 4/9 to 6/9 assign dynamic address databases to VLANs, ports, and bridge groups (the lowest available FID is cleared and assigned), and thus restore support for per-port FDB operations. Patchs 7/9 to 9/9 refine ports isolation and setup 802.1Q on user demand. With this patchset, ports get correctly bridged and the driver behaves as expected, with or without 802.1Q support. With CONFIG_VLAN_8021Q enabled, setting a default PVID to the bridge correctly propagates the corresponding VLAN, in addition to the hardware bridging: # echo 42 > /sys/class/net/<bridge>/bridge/default_pvid But considering CONFIG_BRIDGE_VLAN_FILTERING enabled, the hardware VLAN filtering is enabled on all bridge members only when the user requests it: # echo 1 > /sys/class/net/<bridge>/bridge/vlan_filtering ==================== Signed-off-by: -
Vivien Didelot authored
Implement port_vlan_filtering in the driver to toggle the related port 802.1Q mode between DISABLED and SECURE, on user request. Signed-off-by:
Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by:
-
Vivien Didelot authored
Now that ports isolation is correctly configured when joining or leaving a bridge, there is no need to rely on reserved VLANs to isolate unbridged ports anymore. Thus remove them, and disable 802.1Q on setup. This restores the expected behavior of hardware bridging for systems without 802.1Q or VLAN filtering enabled. Signed-off-by:
-
Vivien Didelot authored
The In Chip Port Based VLAN Table contains bits used to restrict which output ports this input port can send frames to. With the VLAN filtering enabled, these tables work in conjunction with the VLAN Table Unit to allow egressing frames. In order to remove the current dependency to BRIDGE_VLAN_FILTERING for basic hardware bridging to work, it is necessary to restore a fine control of each port's VLANTable, on setup and when a port joins or leaves a bridge. Signed-off-by:
-
Vivien Didelot authored
Give a new bridge a fresh FDB, assign it to its members, and restore a fresh FDB to a port leaving a bridge. Signed-off-by:
-
Vivien Didelot authored
Restore per-port FDB. Assign them on setup, allow adding and deleting addresses into them, and dump them. Signed-off-by:
-
Vivien Didelot authored
Add a _mv88e6xxx_fid_new function which gives and flushes the lowest FID available. Call it when preparing a new VTU entry. Signed-off-by:
-
Vivien Didelot authored
Move out the code which dumps a single FDB to its own function. Signed-off-by:
-
