- 23 Feb, 2022 30 commits
-
-
Charlene Liu authored
[Why&How] add debug option to bypass ssinfo from bios. Reviewed-by:
Chris Park <Chris.Park@amd.com> Acked-by:
Solomon Chiu <solomon.chiu@amd.com> Signed-off-by:
Charlene Liu <Charlene.Liu@amd.com> Tested-by:
Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com>
-
George Shen authored
[Why] All fixed VS/PE link training sequence should be refactored into a separate function outside of the standard link training sequence. This includes the sequence for non-transparent mode. [How] Isolate link training sequence for fixed VS/PE non-transparent mode into a separate function. Reviewed-by:
Wenjing Liu <Wenjing.Liu@amd.com> Acked-by:
George Shen <George.Shen@amd.com> Tested-by:
-
Wenjing Liu authored
[how] Call to DMUB to retrieve usb c cable ID data from PD firmware. If cable id is retrieved from DMUB, skip reading cable ID from RX. Reviewed-by:
-
Wayne Lin authored
[Why] Currently, we don't have code path to release remote dc_sink when unplug MST hub from the system. After few times hotplug, we hit the limition of maximum number of remote dc_sink and can't light up new connected monitor anymore. [How] Releasing all remote dc_sink at dm_helpers_dp_mst_stop_top_mgr() was removed by previous patch. Restore it. Reviewed-by:
Jerry Zuo <Jerry.Zuo@amd.com> Acked-by:
Wayne Lin <Wayne.Lin@amd.com> Tested-by:
-
Fangzhi Zuo authored
[Why] When hotplug or unplug happens, each stream disabled one by one, and then enable any alived streams. Link phy and payload table is cleared when 1st stream is disabled. That causes the error message pops up when disable 2nd stream. There is no active stream after link_rate is cleared. After all streams are disabled, link will be trained again and link rate is assigned to any alived streams. Therefore there is no harm for the error message that represents invalid link rate value in the atomic reset transitional time period. [How] Downgrade the log level from ERROR to DEBUG. Reviewed-by:
-
Ilya authored
[Why] Hotplugging the VGA side of some DP/VGA adapters caused the display to light up with the wrong (non-native) resolution. This is caused by the adapter misbehaving by reporting the wrong number of downstream ports when the VGA side is unplugged (reports 1 instead of 0), but only if the SINK_COUNT DPCD register is read more than once. [How] To work around the adapter behavior, remove the sink if link is detected, but EDID cannot be read. Reviewed-by:
Ilya <Ilya.Bakoulin@amd.com> Tested-by:
-
Po Ting Chen authored
[Why] To move the PSR DPCD caps detection into detect_edp_sink_caps() Reviewed-by:
Anthony Koo <Anthony.Koo@amd.com> Acked-by:
Po Ting Chen <robin.chen@amd.com> Tested-by:
-
Duncan Ma authored
[Why] Detbuffer size is dynamically set for dcn31x. At certain moment, compbuf+(def size * num pipes) > config return buffer size causing flickering. This is easily reproducible when MPO is enabled with two displays. [How] At prepare BW, use the min comp buffer size. When it is to optimize BW, set compbuf size back to maximum possible size. Reviewed-by:
Duncan Ma <duncanma@amd.com> Tested-by:
-
Paul Hsieh authored
[Why] When system resume from sleep, the cursor lock will be reset to default(lock status). And the cursor programming sequence doesn't consider about odm pipe split cause cursor can't be enabled. [How] If odm pipe split has been used, lock/un-lock on each pipes. Reviewed-by:
Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com> Acked-by:
Paul Hsieh <paul.hsieh@amd.com> Tested-by:
-
Maíra Canal authored
Turn previously global functions into static functions to avoid -Wmissing-prototype warnings, such as: drivers/gpu/drm/amd/amdgpu/../display/dc/irq/dcn30/irq_service_dcn30.c:50:20: warning: no previous prototype for function 'to_dal_irq_source_dcn30' [-Wmissing-prototypes] enum dc_irq_source to_dal_irq_source_dcn30( ^ drivers/gpu/drm/amd/amdgpu/../display/dc/irq/dcn30/irq_service_dcn30.c:50:1: note: declare 'static' if the function is not intended to be used outside of this translation unit enum dc_irq_source to_dal_irq_source_dcn30( ^ static 1 warning generated. drivers/gpu/drm/amd/amdgpu/../display/dc/clk_mgr/dcn316/dcn316_clk_mgr.c:488:6: warning: no previous prototype for function 'dcn316_clk_mgr_helper_populate_bw_params' [-Wmissing-prototypes] void dcn316_clk_mgr_helper_populate_bw_params( ^ drivers/gpu/drm/amd/amdgpu/../display/dc/clk_mgr/dcn316/dcn316_clk_mgr.c:488:1: note: declare 'static' if the function is not intended to be used outside of this translation unit void dcn316_clk_mgr_helper_populate_bw_params( ^ static 1 warning generated. v2: drop is_timing_changed hunk (Alex) Signed-off-by:Maíra Canal <maira.canal@usp.br> Signed-off-by:
-
Maíra Canal authored
Include the header with the prototype to silence the following clang warning: drivers/gpu/drm/amd/amdgpu/../display/dc/dcn201/dcn201_init.c:127:6: warning: no previous prototype for function 'dcn201_hw_sequencer_construct' [-Wmissing-prototypes] void dcn201_hw_sequencer_construct(struct dc *dc) ^ Signed-off-by: -
Maíra Canal authored
Remove the variable clamshell_closed from the function dcn10_align_pixel_clocks. This was pointed by clang with the following warning: drivers/gpu/drm/amd/amdgpu/../display/dc/dcn10/dcn10_hw_sequencer.c:2063:7: warning: variable 'clamshell_closed' set but not used [-Wunused-but-set-variable] bool clamshell_closed = false; ^ Signed-off-by: -
Maíra Canal authored
Remove the unused struct irq_source_info_funcs dmub_outbox_irq_info_funcs from the file, which was declared but never hooked up. This was pointed by clang with the following warning: drivers/gpu/drm/amd/amdgpu/../display/dc/irq/dcn201/irq_service_dcn201.c:141:43: warning: unused variable 'dmub_outbox_irq_info_funcs' [-Wunused-const-variable] static const struct irq_source_info_funcs dmub_outbox_irq_info_funcs = { ^ Signed-off-by: -
Maíra Canal authored
Remove the vupdate_int_entry definition and utilization to avoid the following warning by Clang: drivers/gpu/drm/amd/amdgpu/../display/dc/irq/dcn21/irq_service_dcn21.c:410:2: warning: initializer overrides prior initialization of this subobject [-Winitializer-overrides] vupdate_no_lock_int_entry(0), ^~~~~~~~~~~~~~~~~~~~~~~~~~~~ drivers/gpu/drm/amd/amdgpu/../display/dc/irq/dcn21/irq_service_dcn21.c:280:39: note: expanded from macro 'vupdate_no_lock_int_entry' [DC_IRQ_SOURCE_VUPDATE1 + reg_num] = {\ ^~ drivers/gpu/drm/amd/amdgpu/../display/dc/irq/dcn21/irq_service_dcn21.c:404:2: note: previous initialization is here vupdate_int_entry(0), ^~~~~~~~~~~~~~~~~~~~ drivers/gpu/drm/amd/amdgpu/../display/dc/irq/dcn21/irq_service_dcn21.c:269:39: note: expanded from macro 'vupdate_int_entry' [DC_IRQ_SOURCE_VUPDATE1 + reg_num] = {\ ^~ drivers/gpu/drm/amd/amdgpu/../display/dc/irq/dcn21/irq_service_dcn21.c:411:2: warning: initializer overrides prior initialization of this subobject [-Winitializer-overrides] vupdate_no_lock_int_entry(1), ^~~~~~~~~~~~~~~~~~~~~~~~~~~~ drivers/gpu/drm/amd/amdgpu/../display/dc/irq/dcn21/irq_service_dcn21.c:280:39: note: expanded from macro 'vupdate_no_lock_int_entry' [DC_IRQ_SOURCE_VUPDATE1 + reg_num] = {\ ^~ drivers/gpu/drm/amd/amdgpu/../display/dc/irq/dcn21/irq_service_dcn21.c:405:2: note: previous initialization is here vupdate_int_entry(1), ^~~~~~~~~~~~~~~~~~~~ drivers/gpu/drm/amd/amdgpu/../display/dc/irq/dcn21/irq_service_dcn21.c:269:39: note: expanded from macro 'vupdate_int_entry' [DC_IRQ_SOURCE_VUPDATE1 + reg_num] = {\ ^~ drivers/gpu/drm/amd/amdgpu/../display/dc/irq/dcn21/irq_service_dcn21.c:412:2: warning: initializer overrides prior initialization of this subobject [-Winitializer-overrides] vupdate_no_lock_int_entry(2), ^~~~~~~~~~~~~~~~~~~~~~~~~~~~ drivers/gpu/drm/amd/amdgpu/../display/dc/irq/dcn21/irq_service_dcn21.c:280:39: note: expanded from macro 'vupdate_no_lock_int_entry' [DC_IRQ_SOURCE_VUPDATE1 + reg_num] = {\ ^~ drivers/gpu/drm/amd/amdgpu/../display/dc/irq/dcn21/irq_service_dcn21.c:406:2: note: previous initialization is here vupdate_int_entry(2), ^~~~~~~~~~~~~~~~~~~~ drivers/gpu/drm/amd/amdgpu/../display/dc/irq/dcn21/irq_service_dcn21.c:269:39: note: expanded from macro 'vupdate_int_entry' [DC_IRQ_SOURCE_VUPDATE1 + reg_num] = {\ ^~ drivers/gpu/drm/amd/amdgpu/../display/dc/irq/dcn21/irq_service_dcn21.c:413:2: warning: initializer overrides prior initialization of this subobject [-Winitializer-overrides] vupdate_no_lock_int_entry(3), ^~~~~~~~~~~~~~~~~~~~~~~~~~~~ drivers/gpu/drm/amd/amdgpu/../display/dc/irq/dcn21/irq_service_dcn21.c:280:39: note: expanded from macro 'vupdate_no_lock_int_entry' [DC_IRQ_SOURCE_VUPDATE1 + reg_num] = {\ ^~ drivers/gpu/drm/amd/amdgpu/../display/dc/irq/dcn21/irq_service_dcn21.c:407:2: note: previous initialization is here vupdate_int_entry(3), ^~~~~~~~~~~~~~~~~~~~ drivers/gpu/drm/amd/amdgpu/../display/dc/irq/dcn21/irq_service_dcn21.c:269:39: note: expanded from macro 'vupdate_int_entry' [DC_IRQ_SOURCE_VUPDATE1 + reg_num] = {\ ^~ drivers/gpu/drm/amd/amdgpu/../display/dc/irq/dcn21/irq_service_dcn21.c:414:2: warning: initializer overrides prior initialization of this subobject [-Winitializer-overrides] vupdate_no_lock_int_entry(4), ^~~~~~~~~~~~~~~~~~~~~~~~~~~~ drivers/gpu/drm/amd/amdgpu/../display/dc/irq/dcn21/irq_service_dcn21.c:280:39: note: expanded from macro 'vupdate_no_lock_int_entry' [DC_IRQ_SOURCE_VUPDATE1 + reg_num] = {\ ^~ drivers/gpu/drm/amd/amdgpu/../display/dc/irq/dcn21/irq_service_dcn21.c:408:2: note: previous initialization is here vupdate_int_entry(4), ^~~~~~~~~~~~~~~~~~~~ drivers/gpu/drm/amd/amdgpu/../display/dc/irq/dcn21/irq_service_dcn21.c:269:39: note: expanded from macro 'vupdate_int_entry' [DC_IRQ_SOURCE_VUPDATE1 + reg_num] = {\ ^~ drivers/gpu/drm/amd/amdgpu/../display/dc/irq/dcn21/irq_service_dcn21.c:415:2: warning: initializer overrides prior initialization of this subobject [-Winitializer-overrides] vupdate_no_lock_int_entry(5), ^~~~~~~~~~~~~~~~~~~~~~~~~~~~ drivers/gpu/drm/amd/amdgpu/../display/dc/irq/dcn21/irq_service_dcn21.c:280:39: note: expanded from macro 'vupdate_no_lock_int_entry' [DC_IRQ_SOURCE_VUPDATE1 + reg_num] = {\ ^~ drivers/gpu/drm/amd/amdgpu/../display/dc/irq/dcn21/irq_service_dcn21.c:409:2: note: previous initialization is here vupdate_int_entry(5), ^~~~~~~~~~~~~~~~~~~~ drivers/gpu/drm/amd/amdgpu/../display/dc/irq/dcn21/irq_service_dcn21.c:269:39: note: expanded from macro 'vupdate_int_entry' [DC_IRQ_SOURCE_VUPDATE1 + reg_num] = {\ ^~ 6 warnings generated. Fixes: 688f97ed ("drm/amd/display: Add vupdate_no_lock interrupts for DCN2.1") Signed-off-by: -
Maíra Canal authored
Remove dcn316_smu_set_voltage_via_phyclk function, which is not used in the codebase. This was pointed by clang with the following warning: drivers/gpu/drm/amd/amdgpu/../display/dc/clk_mgr/dcn316/dcn316_smu.c:171:5: warning: no previous prototype for function 'dcn316_smu_set_voltage_via_phyclk' [-Wmissing-prototypes] int dcn316_smu_set_voltage_via_phyclk(struct clk_mgr_internal *clk_mgr, int requested_phyclk_khz) ^ Signed-off-by: -
Maíra Canal authored
Remove unused temp variable from the dmub_rb_flush_pending function by using arithmetic to remove the loop. The -Wunused-but-set-variable warning was pointed out by Clang with the following warning: drivers/gpu/drm/amd/amdgpu/../display/dmub/inc/dmub_cmd.h:2921:12: warning: variable 'temp' set but not used [-Wunused-but-set-variable] uint64_t temp; ^ v2: squash in revert and comment update (Alex) Signed-off-by: -
Maíra Canal authored
Remove get_umc_v8_7_channel_index function, which is not used in the codebase. This was pointed by clang with the following warning: drivers/gpu/drm/amd/amdgpu/umc_v8_7.c:50:24: warning: unused function 'get_umc_v8_7_channel_index' [-Wunused-function] static inline uint32_t get_umc_v8_7_channel_index(struct amdgpu_device *adev, ^ Signed-off-by: -
Maíra Canal authored
Turn previously global function into a static function to avoid the following Clang warning: drivers/gpu/drm/amd/amdgpu/amdgpu_ras.c:2459:5: warning: no previous prototype for function 'amdgpu_ras_block_late_init_default' [-Wmissing-prototypes] int amdgpu_ras_block_late_init_default(struct amdgpu_device *adev, ^ drivers/gpu/drm/amd/amdgpu/amdgpu_ras.c:2459:1: note: declare 'static' if the function is not intended to be used outside of this translation unit int amdgpu_ras_block_late_init_default(struct amdgpu_device *adev, ^ static Signed-off-by: -
Alex Deucher authored
To protect against wraparounds. Reviewed-by:
Christian König <christian.koenig@amd.com> Signed-off-by:
-
Alex Deucher authored
Simplifies the code quite a bit. Reviewed-by:
-
Alex Deucher authored
Rather than duplicating the logic in two places, consolidate the logic in the display manager. Acked-by:
Yifan Zhang <yifan1.zhang@amd.com> Signed-off-by:
-
Alex Deucher authored
Separate the logic for each of these features to make the code easier to understand and update in the future. Acked-by:
-
Alex Deucher authored
This test is not particularly useful now that GTT and GART are decoupled in the driver. Reviewed-by:
-
Alex Deucher authored
Now that we expose the benchmarks via debugfs, there is no longer a need for the module parameter. Reviewed-by:
-
Alex Deucher authored
They provide a nice smoke test of transfer performance using SDMA. Allow the user to run these at runtime rather than only at init time. v2: fix permissions (Alex) Reviewed-by:
-
Felix Kuehling authored
kfd_chardev() doesn't provide much useful information in dev_... messages on multi-GPU systems because there is only one KFD device, which doesn't correspond to any particular GPU. Use the actual GPU device to indicate the GPU that caused a message. Signed-off-by:
Felix Kuehling <Felix.Kuehling@amd.com> Reviewed-by:
-
David Yat Sin authored
Fix for possible integer overflow when doing addition. Reported-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
David Yat Sin <david.yatsin@amd.com> Reviewed-by:
-
Alex Deucher authored
To avoid multiple runs in parallel to avoid mixing results. Reviewed-by:
-
Alex Deucher authored
So you can tell which benchmark was run. v2: print the test description as well Reviewed-by:
-
Alex Deucher authored
So we can tell when this function fails. v2: squash in error handling fix (Alex) Reviewed-by:
-
- 22 Feb, 2022 10 commits
-
-
Alex Deucher authored
So we can tell which output goes to which device when multiple GPUs are present. Also while we are here, convert DRM_ERROR to dev_info. The error cases are not critical. Reviewed-by:
-
Alex Deucher authored
The driver has a fallback so make the message informational rather than a warning. The driver has a fallback if the Component Resource Association Table (CRAT) is missing, so make this informational now. Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1906Reviewed-by:
-
Paul Menzel authored
Signed-off-by:
Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by:
-
Guchun Chen authored
Based on firmware team's input, harvest table in VBIOS does not apply well to legacy products like Navi1x, so seperate harvest mask configuration retrieve from different places. On legacy GPUs, scan harvest bit per IP data stuctures, while for newer ones, still read IP harvest info from harvest table. v2: squash in fix to limit it to specific skus (Guchun) Signed-off-by:
Guchun Chen <guchun.chen@amd.com> Reviewed-by:
-
Prike Liang authored
There's always miss the SMU feature enabled checked in the NPI phase, so let validate the SMU feature enable message directly rather than add more and more MP1 version check. Signed-off-by:
Prike Liang <Prike.Liang@amd.com> Signed-off-by:
Lijo Lazar <Lijo.Lazar@amd.com> Reviewed-by:
-
Prike Liang authored
The TMZ is disabled by default and enable TMZ option for the IP discovery based asic will help on the TMZ function verification. Signed-off-by:
Aaron Liu <aaron.liu@amd.com> Acked-by:
-
Guchun Chen authored
vkms leverages common amdgpu framebuffer creation, and also as it does not support FB modifier, there is no need to check tiling flags when initing framebuffer when virtual display is enabled. This can fix below calltrace: amdgpu 0000:00:08.0: GFX9+ requires FB check based on format modifier WARNING: CPU: 0 PID: 1023 at drivers/gpu/drm/amd/amdgpu/amdgpu_display.c:1150 amdgpu_display_framebuffer_init+0x8e7/0xb40 [amdgpu] v2: check adev->enable_virtual_display instead as vkms can be enabled in bare metal as well. Signed-off-by:
Leslie Shi <Yuliang.Shi@amd.com> Signed-off-by:
-
Guchun Chen authored
This reverts commit 4046afce. No need to support modifier in virtual kms, otherwise, in SRIOV mode, when lanuching X server, set crtc will fail due to mismatch between primary plane modifier and framebuffer modifier. Signed-off-by:
-
Felix Kuehling authored
Clang static analysis reports this problem kfd_chardev.c:2327:2: warning: 1st function call argument is an uninitialized value kvfree(bo_privs); ^~~~~~~~~~~~~~~~ Make sure bo_buckets and bo_privs are initialized so freeing them in the error handling code path will never result in undefined behaviour. Fixes: 73fa13b6 ("drm/amdkfd: CRIU Implement KFD restore ioctl") Reported-by:
Tom Rix <trix@redhat.com> Signed-off-by:
Rajneesh Bhardwaj <rajneesh.bhardwaj@amd.com> Signed-off-by:
-
Kent Russell authored
When this was first implemented, overflows weren't expected in regular operations, and tests weren't in place to cause said overflow. Now there are cases where overflows occur with real workloads, but we know that the kernel can handle this robustly, so move the message to a debug message. Signed-off-by:
Kent Russell <kent.russell@amd.com> Reviewed-by:
-
