- 16 Sep, 2016 11 commits
-
-
Yonatan Cohen authored
rxe_requester() is sending a pkt with rxe_xmit_packet() and then calls rxe_update() to update the wqe and qp's psn values. But sometimes the response is received before the requester had time to update the wqe in which case the completer acts on errornous wqe values. This fix updates the wqe and qp before actually sending the request and rolls back when xmit fails. Fixes: 8700e3e7 ("Soft RoCE driver") Signed-off-by:
Yonatan Cohen <yonatanc@mellanox.com> Signed-off-by:
Leon Romanovsky <leon@kernel.org> Signed-off-by:
Doug Ledford <dledford@redhat.com>
-
Yonatan Cohen authored
When handling ack for atomic opcodes like "fetch&add" or "cmp&swp", the method send_atomic_ack() saves the ack before sending it, in case it gets lost and never reach the requester. In which case the method duplicate_request() will need to find it using the duplicated request.psn. But send_atomic_ack() used a wrong psn value and thus the above ack was never found. This fix uses the ack.psn to locate the ack in case its needed. This fix also copies the ack packet to the skb's control buffer since duplicate_request() will need it when calling rxe_xmit_packet() Fixes: 8700e3e7 ("Soft RoCE driver") Signed-off-by:
-
Yonatan Cohen authored
Disable creation of a UDP socket for ipv6 when CONFIG_IPV6 is not enabeld. Since udp_sock_create6() returns 0 when CONFIG_IPV6 is not set [ 46.888632] IP: [<c220705a>] setup_udp_tunnel_sock+0x6/0x4f [ 46.891355] *pdpt = 0000000000000000 *pde = f000ff53f000ff53 [ 46.893918] Oops: 0002 [#1] PREEMPT [ 46.896014] CPU: 0 PID: 1 Comm: swapper Not tainted 4.7.0-rc4-00001-g8700e3e7 #1 [ 46.900280] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Debian-1.8.2-1 04/01/2014 [ 46.904905] task: cf06c040 ti: cf05e000 task.ti: cf05e000 [ 46.907854] EIP: 0060:[<c220705a>] EFLAGS: 00210246 CPU: 0 [ 46.911137] EIP is at setup_udp_tunnel_sock+0x6/0x4f [ 46.914070] EAX: 00000044 EBX: 00000001 ECX: cf05fef0 EDX: ca8142e0 [ 46.917236] ESI: c2c4505b EDI: cf05fef0 EBP: cf05fed0 ESP: cf05fed0 [ 46.919836] DS: 007b ES: 007b FS: 0000 GS: 00e0 SS: 0068 [ 46.922046] CR0: 80050033 CR2: 000001fc CR3: 02cec000 CR4: 000006b0 [ 46.924550] Stack: [ 46.926014] cf05ff10 c1fd4657 ca8142e0 0000000a 00000000 00000000 0000b712 00000008 [ 46.931274] 00000000 6bb5bd01 c1fd48de 00000000 00000000 cf05ff1c 00000000 00000000 [ 46.936122] cf05ff1c c1fd4bdf 00000000 cf05ff28 c2c4507b ffffffff cf05ff88 c2bf1c74 [ 46.942350] Call Trace: [ 46.944403] [<c1fd4657>] rxe_setup_udp_tunnel+0x8f/0x99 [ 46.947689] [<c1fd48de>] ? net_to_rxe+0x4e/0x4e [ 46.950567] [<c1fd4bdf>] rxe_net_init+0xe/0xa4 [ 46.953147] [<c2c4507b>] rxe_module_init+0x20/0x4c [ 46.955448] [<c2bf1c74>] do_one_initcall+0x89/0x113 [ 46.957797] [<c2bf15eb>] ? set_debug_rodata+0xf/0xf [ 46.959966] [<c2bf1dbc>] ? kernel_init_freeable+0xbe/0x15b [ 46.962262] [<c2bf1ddc>] kernel_init_freeable+0xde/0x15b [ 46.964418] [<c232eb54>] kernel_init+0x8/0xd0 [ 46.966618] [<c2333122>] ret_from_kernel_thread+0xe/0x24 [ 46.969592] [<c232eb4c>] ? rest_init+0x6f/0x6f Fixes: 8700e3e7 ("Soft RoCE driver") Signed-off-by:
-
Maor Gottlieb authored
Set the source mac address in the FTE when L2 specification is provided. Fixes: 038d2ef8 ('IB/mlx5: Add flow steering support') Signed-off-by:
Maor Gottlieb <maorg@mellanox.com> Signed-off-by:
-
Noa Osherovich authored
MAD_IFC command is supported only for physical functions (PF) and when physical port is IB. The proposed fix enforces it. Fixes: d603c809 ("IB/mlx5: Fix decision on using MAD_IFC") Reported-by:
David Chang <dchang@suse.com> Signed-off-by:
Noa Osherovich <noaos@mellanox.com> Signed-off-by:
-
Kamal Heib authored
Modify the mlx4_ib_diag_counters() to avoid the following error in the hypervisor when the slave tries to query the hardware counters in SR-IOV mode. mlx4_core 0000:81:00.0: Unknown command:0x30 accepted from slave:1 Fixes: 3f85f2aa ("IB/mlx4: Add diagnostic hardware counters") Signed-off-by:
Kamal Heib <kamalh@mellanox.com> Signed-off-by:
-
Jack Morgenstein authored
When sending QP1 MAD packets which use a GRH, the source GID (which consists of the 64-bit subnet prefix, and the 64 bit port GUID) must be included in the packet GRH. For SR-IOV, a GID cache is used, since the source GID needs to be the slave's source GID, and not the Hypervisor's GID. This cache also included a subnet_prefix. Unfortunately, the subnet_prefix field in the cache was never initialized (to the default subnet prefix 0xfe80::0). As a result, this field remained all zeroes. Therefore, when SR-IOV was active, all QP1 packets which included a GRH had a source GID subnet prefix of all-zeroes. However, the subnet-prefix should initially be 0xfe80::0 (the default subnet prefix). In addition, if OpenSM modifies a port's subnet prefix, the new subnet prefix must be used in the GRH when sending QP1 packets. To fix this we now initialize the subnet prefix in the SR-IOV GID cache to the default subnet prefix. We update the cached value if/when OpenSM modifies the port's subnet prefix. We take this cached value when sending QP1 packets when SR-IOV is active. Note that the value is stored as an atomic64. This eliminates any need for locking when the subnet prefix is being updated. Note also that we depend on the FW generating the "port management change" event for tracking subnet-prefix changes performed by OpenSM. If running early FW (before 2.9.4630), subnet prefix changes will not be tracked (but the default subnet prefix still will be stored in the cache; therefore users who do not modify the subnet prefix will not have a problem). IF there is a need for such tracking also for early FW, we will add that capability in a subsequent patch. Fixes: 1ffeb2eb ("IB/mlx4: SR-IOV IB context objects and proxy/tunnel SQP support") Signed-off-by:
Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by:
-
Jack Morgenstein authored
The indentation in the QP1 GRH flow in procedure build_mlx_header is really confusing. Fix it, in preparation for a commit which touches this code. Fixes: 1ffeb2eb ("IB/mlx4: SR-IOV IB context objects and proxy/tunnel SQP support") Signed-off-by:
-
Alex Vesker authored
Because of an incorrect bit-masking done on the join state bits, when handling a join request we failed to detect a difference between the group join state and the request join state when joining as send only full member (0x8). This caused the MC join request not to be sent. This issue is relevant only when SRIOV is enabled and SM supports send only full member. This fix separates scope bits and join states bits a nibble each. Fixes: b9c5d6a6 ('IB/mlx4: Add multicast group (MCG) paravirtualization for SR-IOV') Signed-off-by:
Alex Vesker <valex@mellanox.com> Signed-off-by:
-
Alex Vesker authored
This fix solves a race between light flush and on the fly joins. Light flush doesn't set the device to down and unset IPOIB_OPER_UP flag, this means that if while flushing we have a MC join in progress and the QP was attached to BC MGID we can have a mismatches when re-attaching a QP to the BC MGID. The light flush would set the broadcast group to NULL causing an on the fly join to rejoin and reattach to the BC MCG as well as adding the BC MGID to the multicast list. The flush process would later on remove the BC MGID and detach it from the QP. On the next flush the BC MGID is present in the multicast list but not found when trying to detach it because of the previous double attach and single detach. [18332.714265] ------------[ cut here ]------------ [18332.717775] WARNING: CPU: 6 PID: 3767 at drivers/infiniband/core/verbs.c:280 ib_dealloc_pd+0xff/0x120 [ib_core] ... [18332.775198] Hardware name: Red Hat KVM, BIOS Bochs 01/01/2011 [18332.779411] 0000000000000000 ffff8800b50dfbb0 ffffffff813fed47 0000000000000000 [18332.784960] 0000000000000000 ffff8800b50dfbf0 ffffffff8109add1 0000011832f58300 [18332.790547] ffff880226a596c0 ffff880032482000 ffff880032482830 ffff880226a59280 [18332.796199] Call Trace: [18332.798015] [<ffffffff813fed47>] dump_stack+0x63/0x8c [18332.801831] [<ffffffff8109add1>] __warn+0xd1/0xf0 [18332.805403] [<ffffffff8109aebd>] warn_slowpath_null+0x1d/0x20 [18332.809706] [<ffffffffa025d90f>] ib_dealloc_pd+0xff/0x120 [ib_core] [18332.814384] [<ffffffffa04f3d7c>] ipoib_transport_dev_cleanup+0xfc/0x1d0 [ib_ipoib] [18332.820031] [<ffffffffa04ed648>] ipoib_ib_dev_cleanup+0x98/0x110 [ib_ipoib] [18332.825220] [<ffffffffa04e62c8>] ipoib_dev_cleanup+0x2d8/0x550 [ib_ipoib] [18332.830290] [<ffffffffa04e656f>] ipoib_uninit+0x2f/0x40 [ib_ipoib] [18332.834911] [<ffffffff81772a8a>] rollback_registered_many+0x1aa/0x2c0 [18332.839741] [<ffffffff81772bd1>] rollback_registered+0x31/0x40 [18332.844091] [<ffffffff81773b18>] unregister_netdevice_queue+0x48/0x80 [18332.848880] [<ffffffffa04f489b>] ipoib_vlan_delete+0x1fb/0x290 [ib_ipoib] [18332.853848] [<ffffffffa04df1cd>] delete_child+0x7d/0xf0 [ib_ipoib] [18332.858474] [<ffffffff81520c08>] dev_attr_store+0x18/0x30 [18332.862510] [<ffffffff8127fe4a>] sysfs_kf_write+0x3a/0x50 [18332.866349] [<ffffffff8127f4e0>] kernfs_fop_write+0x120/0x170 [18332.870471] [<ffffffff81207198>] __vfs_write+0x28/0xe0 [18332.874152] [<ffffffff810e09bf>] ? percpu_down_read+0x1f/0x50 [18332.878274] [<ffffffff81208062>] vfs_write+0xa2/0x1a0 [18332.881896] [<ffffffff812093a6>] SyS_write+0x46/0xa0 [18332.885632] [<ffffffff810039b7>] do_syscall_64+0x57/0xb0 [18332.889709] [<ffffffff81883321>] entry_SYSCALL64_slow_path+0x25/0x25 [18332.894727] ---[ end trace 09ebbe31f831ef17 ]--- Fixes: ee1e2c82 ("IPoIB: Refresh paths instead of flushing them on SM change events") Signed-off-by:
-
Alexey Khoroshilov authored
There is skb_clone(skb, GFP_KERNEL) in spinlock context in rxe_rcv_mcast_pkt(). Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by:
Alexey Khoroshilov <khoroshilov@ispras.ru> Acked-by:
Moni Shoua <monis@mellanox.com> Signed-off-by:
-
- 02 Sep, 2016 17 commits
-
-
Mike Marciniszyn authored
The debugfs RCU trips many debug kernel warnings because of potential sleeps with an RCU read lock held. This includes both user copy calls and slab allocations throughout the file. This patch switches the RCU to use SRCU for file remove/access race protection. In one case, the SRCU is implicit in the use of the raw debugfs file object and just works. In the seq_file case, a wrapper around seq_read() and seq_lseek() is used to enforce the SRCU using the debugfs supplied functions debugfs_use_file_start() and debugfs_use_file_stop(). The sychronize_rcu() is deleted since the SRCU prevents the remove access race. The RCU locking is kept for qp_stats since the QP hash list is protected using the non-sleepable RCU. Reviewed-by:
Sebastian Sanchez <sebastian.sanchez@intel.com> Signed-off-by:
Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by:
Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by:
-
Harish Chegondi authored
The global variable n_krcvqs stores the sum of the number of kernel receive queues of VLs 0-7 which the user can pass to the driver through the module parameter array krcvqs which is of type unsigned integer. If the user passes large value(s) into krcvqs parameter array, it can cause an arithmetic overflow while calculating n_krcvqs which is also of type unsigned int. The overflow results in an incorrect value of n_krcvqs which can lead to kernel crash while loading the driver. Fix by changing the data type of n_krcvqs to unsigned long. This patch also changes the data type of other variables that get their values from n_krcvqs. Reviewed-by:
Harish Chegondi <harish.chegondi@intel.com> Signed-off-by:
-
Dean Luick authored
Sometimes a QSFP device does not respond in the expected time after a power-on. Add a read pre-check/retry when starting the link on driver load. Reviewed-by:
Easwar Hariharan <easwar.hariharan@intel.com> Signed-off-by:
Dean Luick <dean.luick@intel.com> Signed-off-by:
-
Jubin John authored
In the set_txreq_header_ahg(), The KDETH Intr bit is obtained from the header in the user sdma request using a KDETH_GET shift and mask macro. This value is then futher right shifted by 16 causing us to lose the value i.e it is shifted to zero, leading to the following smatch warning: drivers/infiniband/hw/hfi1/user_sdma.c:1482 set_txreq_header_ahg() warn: mask and shift to zero The Intr bit should be left shifted into its correct position in the KDETH header before the AHG update. Reported-by:
Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by:
Mitko Haralanov <mitko.haralanov@intel.com> Reviewed-by:
Jubin John <jubin.john@intel.com> Signed-off-by:
-
Sebastian Sanchez authored
When trying to align the source pointer and there's a byte carry in an SGE copy, bytes are borrowed from the next quad-word X to complete the required quad-word copy. Then, the SGE length is reduced by the number of borrowed bytes. After this, if the remaining number of bytes from quad-word X (extra bytes) is greater than the new SGE length, the number of extra bytes needs to be updated to the new SGE length. Otherwise, when the SGE length gets updated again after the extra bytes are read to create the new byte carry, it goes negative, which then becomes a very large number as the SGE length is an unsigned integer. This causes SGE buffer to be over-read. Reviewed-by:
-
Leon Romanovsky authored
Remove returning errors from mlx5 poll_cq function. Polling CQ operation in kernel never fails by Mellanox HCA architecture and respective driver design. Signed-off-by:
Leon Romanovsky <leonro@mellanox.com> Signed-off-by:
-
Yishai Hadas authored
Use TIR number based on selector, it should be done to differentiate between RSS QP to RAW one. Reported-by:
Sagi Grimberg <sagi@grimberg.me> Signed-off-by:
Yishai Hadas <yishaih@mellanox.com> Signed-off-by:
-
Leon Romanovsky authored
Return variable was set in a line before the actual return was called in begin_wqe function. This patch removes such variable and simplifies the code. Signed-off-by:
-
Chuck Lever authored
The returned value should be EINVAL, because it is caused by wrong caller and not by internal overflow event. Signed-off-by:
Chuck Lever <chuck.lever@oracle.com> Signed-off-by:
-
Leon Romanovsky authored
Remove returning errors from mlx4 poll_cq function. Polling CQ operation in kernel never fails by Mellanox HCA architecture and respective driver design. Signed-off-by:
-
Leon Romanovsky authored
By Mellanox HW design and SW implementation, poll_cq never fails and returns errors, so all these printks are to catch ULP bugs. In case of such bug, the reverted patch will cause reentry of the function, resulting in a printk storm. This reverts commit 5412352f ("IB/mlx4: Return EAGAIN for any error in mlx4_ib_poll_one") Signed-off-by:
-
Erez Shitrit authored
When a new CM connection is being requested, ipoib driver copies data from the path pointer in the CM/tx object, the path object might be invalid at the point and memory corruption will happened later when now the CM driver will try using that data. The next scenario demonstrates it: neigh_add_path --> ipoib_cm_create_tx --> queue_work (pointer to path is in the cm/tx struct) #while the work is still in the queue, #the port goes down and causes the ipoib_flush_paths: ipoib_flush_paths --> path_free --> kfree(path) #at this point the work scheduled starts. ipoib_cm_tx_start --> copy from the (invalid)path pointer: (memcpy(&pathrec, &p->path->pathrec, sizeof pathrec);) -> memory corruption. To fix that the driver now starts the CM/tx connection only if that specific path exists in the general paths database. This check is protected with the relevant locks, and uses the gid from the neigh member in the CM/tx object which is valid according to the ref count that was taken by the CM/tx. Fixes: 839fcaba ('IPoIB: Connected mode experimental support') Signed-off-by:
Erez Shitrit <erezsh@mellanox.com> Signed-off-by:
-
Erez Shitrit authored
The function send_leave sets the member: group->query_id (group->query_id = ret) after calling the sa_query, but leave_handler can be executed before the setting and it might delete the group object, and will get a memory corruption. Additionally, this patch gets rid of group->query_id variable which is not used. Fixes: faec2f7b ('IB/sa: Track multicast join/leave requests') Signed-off-by:
-
Baoyou Xie authored
We get 1 warning when build kernel with W=1: drivers/infiniband/hw/cxgb4/qp.c:686:6: warning: no previous prototype for '_free_qp' [-Wmissing-prototypes] In fact, this function is only used in the file in which it is declared and don't need a declaration, but can be made static. so this patch marks it 'static'. Signed-off-by:
Baoyou Xie <baoyou.xie@linaro.org> Reviewed-by:
Yuval Shaia <yuval.shaia@oracle.com> Reviewed-by:
Steve Wise <swise@opengridcomputing.com> Signed-off-by:
-
Raju Rangoju authored
When the low level driver exercises the hot unplug they would call rdma_cm cma_remove_one which would fire DEVICE_REMOVAL event to all cma consumers. Now, if consumer doesn't make sure they destroy all IB objects created on that IB device instance prior to finalizing all processing of DEVICE_REMOVAL callback, rdma_cm will let the lld to de-register with IB core and destroy the IB device instance. And if the consumer calls (say) ib_dereg_mr(), it will crash since that dev object is NULL. In the current implementation, iser-target just initiates the cleanup and returns from DEVICE_REMOVAL callback. This deferred work creates a race between iser-target cleaning IB objects(say MR) and lld destroying IB device instance. This patch includes the following fixes -> make sure that consumer frees all IB objects associated with device instance -> return non-zero from the callback to destroy the rdma_cm id Signed-off-by:Raju Rangoju <rajur@chelsio.com> Acked-by:
-
Christophe Jaillet authored
The 2nd parameter of 'find_first_bit' is the number of bits to search. In this case, we are passing 'sizeof(u64)' which is 8. It is likely that the number of bits of 'port_mask' was expected here. Use sizeof() * 8 to get the correct number. It has been spotted by the following coccinelle script: @@ expression ret, x; @@ * ret = \(find_first_bit \| find_first_zero_bit\) (x, sizeof(...)); Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by:
-
Christophe Jaillet authored
The 2nd parameter of 'find_first_bit' is the number of bits to search. In this case, we are passing 'sizeof(tmp)' which is likely to be 4 or 8 because 'tmp' is an 'unsigned long'. It is likely that the number of bits of 'tmp' was expected here. So use BITS_PER_LONG instead. It has been spotted by the following coccinelle script: @@ expression ret, x; @@ * ret = \(find_first_bit \| find_first_zero_bit\) (x, sizeof(...)); Signed-off-by:
Majd Dibbiny <majd@mellanox.com> Acked-by:
-
- 26 Aug, 2016 3 commits
-
-
Christophe Jaillet authored
In all other places in this file where 'find_first_bit' is called, port_num is defined as a 'u8' and no casting is done. Do the same here in order to be more consistent. Signed-off-by:
-
Shiraz Saleem authored
Device notifications are not received after the first interface is closed; since there is an unregister for notifications on every interface close. Correct this by unregistering for device notifications only when the last interface is closed. Also, make all operations on the i40iw_notifiers_registered atomic as it can be read/modified concurrently. Fixes: 8e06af71 ("i40iw: add main, hdr, status") Signed-off-by:
Mustafa Ismail <mustafa.ismail@intel.com> Signed-off-by:
Shiraz Saleem <shiraz.saleem@intel.com> Signed-off-by:
-
Mustafa Ismail authored
Update iwqp->hw_iwarp_state to reflect the new state of the CQP modify QP operation. This avoids reissuing a CQP operation to modify a QP to a state that it is already in. Fixes: 4e9042e6 ("i40iw: add hw and utils files") Reported-by:
Stefan Assmann <sassmann@redhat.com> Signed-off-by:
-
- 25 Aug, 2016 2 commits
-
-
Doug Ledford authored
-
Tatyana Nikolova authored
Send a zero length last streaming mode message for loopback connections to synchronize between accepting QP and connecting QP. This avoids data transfer to start on the accepting QP before the connecting QP is in RTS. Also remove function i40iw_loopback_nop() as it is no longer used. Fixes: f27b4746 ("i40iw: add connection management code") Signed-off-by:
Tatyana Nikolova <tatyana.e.nikolova@intel.com> Signed-off-by:
-
- 24 Aug, 2016 7 commits
-
-
Doug Ledford authored
If port_guid is set with the default subnet_prefix, then we get a change event and run a port refresh, we don't update the port_guid. As a result, attempts to create a target device that uses the new subnet_prefix in the wwn will fail to find a match and be rejected by the ib_srpt driver. This makes it impossible to configure a port if it was initialized with a default subnet_prefix and later changed to any non-default subnet-prefix. Updating the port refresh task to always update the wwn based upon the current subnext_prefix solves this problem. Cc: Bart Van Assche <bart.vanassche@sandisk.com> Cc: nab@linux-iscsi.org Signed-off-by: -
Selvin Xavier authored
Current driver is reporting wrong values for max_sge and max_sge_rd in query_device. This breaks the nfs rdma and iser in some device profiles. Fixing the driver to report correct values from FW. Signed-off-by:
Selvin Xavier <selvin.xavier@broadcom.com> Signed-off-by:
Devesh Sharma <devesh.sharma@broadcom.com> Signed-off-by:
-
Mustafa Ismail authored
iwpbl->iwmr points to the structure that contains iwpbl, which is iwmr. Setting this to NULL would result in writing to freed memory. So just free iwmr, and return. Fixes: d3749841 ("i40iw: add files for iwarp interface") Reported-by:
-
Mustafa Ismail authored
Memory allocated for iwqp; iwqp->allocated_buffer is freed twice in the create_qp error path. Correct this by having it freed only once in i40iw_free_qp_resources(). Fixes: d3749841 ("i40iw: add files for iwarp interface") Signed-off-by:
-
Chris Wilson authored
This file does not use any structs or functions defined by io-mapping.h (nor does it directly use iomap, ioremap, iounamp or friends). Remove it to simplify verification of changes to io-mapping.h The include existed since its inception in commit e126ba97 Author: Eli Cohen <eli@mellanox.com> Date: Sun Jul 7 17:25:49 2013 +0300 mlx5: Add driver for Mellanox Connect-IB adapters which looks like a copy across from the Mellanox ethernet driver. Signed-off-by:
Chris Wilson <chris@chris-wilson.co.uk> Cc: Eli Cohen <eli@mellanox.com> Cc: Jack Morgenstein <jackm@dev.mellanox.co.il> Cc: Or Gerlitz <ogerlitz@mellanox.com> Cc: Matan Barak <matanb@mellanox.com> Cc: Leon Romanovsky <leonro@mellanox.com> Cc: Doug Ledford <dledford@redhat.com> Cc: Sean Hefty <sean.hefty@intel.com> Cc: Hal Rosenstock <hal.rosenstock@gmail.com> Cc: linux-rdma@vger.kernel.org Reviewed-by:
Laurence Oberman <loberman@redhat.com> Tested-by:
-
Mustafa Ismail authored
In i40iw_free_virt_mem(), do not set mem->va to NULL after freeing it as mem->va is a self-referencing pointer to mem. Fixes: 4e9042e6 ("i40iw: add hw and utils files") Reported-by:
-
Shiraz Saleem authored
Add NULL check for pdata and pdata->addr before the memcpy in i40iw_form_cm_frame(). This fixes a NULL pointer de-reference which occurs when the MPA private data pointer is NULL. Also only copy pdata->size bytes in the memcpy to prevent reading past the length of the private data buffer provided by upper layer. Fixes: f27b4746 ("i40iw: add connection management code") Reported-by:
-
