- 20 Apr, 2016 5 commits
-
-
Stefan Schmidt authored
Catching up with the stack here and implement CCA mode setting. Signed-off-by:
Stefan Schmidt <stefan@osg.samsung.com> Signed-off-by:
Marcel Holtmann <marcel@holtmann.org>
-
Stefan Schmidt authored
Catching up with the stack here and implement CCA ED level setting. Signed-off-by:
-
Stefan Schmidt authored
Catching up with the stack here and implement CSMA parameter setting. Signed-off-by:
-
Takashi Iwai authored
hci_vhci driver creates a hci device object dynamically upon each HCI_VENDOR_PKT write. Although it checks the already created object and returns an error, it's still racy and may build multiple hci_dev objects concurrently when parallel writes are performed, as the device tracks only a single hci_dev object. This patch introduces a mutex to protect against the concurrent device creations. Cc: <stable@vger.kernel.org> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Alexander Aring authored
I expierenced when setting channel while sleep mode it didn't changed the channel inside the hardware registers. Then I got another report of an user which has similar issues. I increased the sleep to off state change timing, which is according at86rf233 at maximum 1000 us. After this change I got no similar effects again. I tried another option to wait on AWAKE_END irq, which can be used to wait until the transceiver is awaked. I tested it and the IRQ took 4 seconds after starting state change. I don't believe it takes 4 seconds to go into the TRX_OFF state from SLEEP state. The alternative is to increase the timings which seems to work. Cc: Oleg Hahm <oliver.hahm@inria.fr> Signed-off-by:
Alexander Aring <aar@pengutronix.de> Reviewed-by: Stefan Schmidt<stefan@osg.samsung.com> Signed-off-by:
-
- 13 Apr, 2016 24 commits
-
-
Alexander Aring authored
In case of link-layer specific handling for 802.15.4 we need to cast to 802.15.4 sepcific structures. Simple add this header when include the 6lowpan header. Signed-off-by:
Jukka Rissanen <jukka.rissanen@linux.intel.com> Signed-off-by:
-
Alexander Aring authored
This patch adds the lowpan_is_ll function, which can be used to make a special 6lowpan linklayer handling for a specific 6lowpan linklayer type. Signed-off-by:
-
Alexander Aring authored
This function will be use in later functionality in other branches than generic 6lowpan, so we move it to the global 6lowpan header. Signed-off-by:
-
Alexander Aring authored
This patch removes unnecessary zero data for a stack variable. Signed-off-by:
-
Alexander Aring authored
This patch adds a lowpan prefix to each functions which doesn't have such prefix currently. Reviewed-by:
-
Alexander Aring authored
This patch moves the 802.15.4 link layer specific structures to generic 6lowpan. This is necessary for special 802.15.4 6lowpan handling in 6lowpan generic layer. Reviewed-by:
-
Alexander Aring authored
This patch changes the naming for interface private data for lowpan intefaces. The current private data scheme is: ------------------------------------------------- | 6LoWPAN Generic | LinkLayer 6LoWPAN | ------------------------------------------------- the current naming schemes are: - 6LoWPAN Generic: - lowpan_priv - LinkLayer 6LoWPAN: - BTLE - lowpan_dev - 802.15.4: - lowpan_dev_info the new naming scheme with this patch will be: - 6LoWPAN Generic: - lowpan_dev - LinkLayer 6LoWPAN: - BTLE - lowpan_btle_dev - 802.15.4: - lowpan_802154_dev Signed-off-by: -
Alexander Aring authored
The short address is unique in combination with the panid. This patch will add the panid for generating an ieee802154 address hash. Reviewed-by:
-
Alexander Aring authored
The generation of autoconfigured IPv6 link-local addresses starts with a notification on interface up. To handle autoconfiguration according to RFC 4944 requires pan id and short address to generate an autoconfigured link-local address. This patch will avoid changing of these link-layer address configuration while lowpan interface is up. Reviewed-by:
-
Alexander Aring authored
This patch introduce some short address handling functionality into ieee802154 headers. Reviewed-by:
-
Alexander Aring authored
This patch removes some const from non-pointer types and fixes the function name for the ieee802154_is_valid_extended_unicast_addr comment. Reviewed-by:
-
Alexandre Macabies authored
We set the TXNSECEN bit of register TXNCON to on when transmitting a security-enabled frame, as described in section 3.12.2 of the MRF datasheet. Signed-off-by:
Alexandre Macabies <web+oss@zopieux.com> Reviewed-by:
Alan Ott <alan@signal11.us> Signed-off-by:
-
Alexandre Macabies authored
When receiving a security-enabled IEEE 802.15.4 frame, the MRF24J40 triggers a SECIF interrupt that needs to be handled for RX processing to keep functioning properly. This patch enables the SECIF interrupt and makes the MRF ignores all hardware processing of security-enabled frames, that is handled by the ieee802154 stack instead. Signed-off-by:
-
Alexandre Macabies authored
ieee802154_is_secen checks if the 802.15.4 security bit is set in the frame control field. Signed-off-by:
-
David S. Miller authored
John Crispin says: ==================== net: mediatek: make the driver pass stress tests While testing the driver we managed to get the TX path to stall and fail to recover. When dual MAC support was added to the driver, the whole queue stop/wake code was not properly adapted. There was also a regression in the locking of the xmit function. The fact that watchdog_timeo was not set and that the tx_timeout code failed to properly reset the dma, irq and queue just made the mess complete. This series make the driver pass stress testing. With this series applied the testbed has been running for several days and still has not locked up. We have a second setup that has a small hack patch applied to randomly stop irqs and/or one of the queues and successfully manages to recover from these simulated tx stalls. ==================== Signed-off-by:David S. Miller <davem@davemloft.net>
-
John Crispin authored
The QID field gets set to the mac id. This made the DMA linked list queue the traffic of each MAC on a different internal queue. However during long term testing we found that this will cause traffic stalls as the multi queue setup requires a more complete initialisation which is not part of the upstream driver yet. This patch removes the code setting the QID field, resulting in all traffic ending up in queue 0 which works without any special setup. Signed-off-by:
John Crispin <blogic@openwrt.org> Signed-off-by:
-
John Crispin authored
The worker always touches both netdevs. It is ethernet core and not MAC specific. We only need one worker, which belongs into the ethernets core struct. Signed-off-by:
-
John Crispin authored
The driver supports 2 MACs. Both run on the same DMA ring. If we hit a TX timeout we need to stop both netdevs before restarting them again. If we don't do this, mtk_stop() wont shutdown DMA and the consecutive call to mtk_open() wont restart DMA and enable IRQs. Signed-off-by:
-
John Crispin authored
Inside the TX path there is a lock inside the tx_map function. This is however too late. The patch moves the lock to the start of the xmit function right before the free count check of the DMA ring happens. If we do not do this, the code becomes racy leading to TX stalls and dropped packets. This happens as there are 2 netdevs running on the same physical DMA ring. Signed-off-by:
-
John Crispin authored
The driver supports 2 MACs. Both run on the same DMA ring. If we go above/below the TX rings threshold value, we always need to wake/stop the queue of both devices. Not doing to can cause TX stalls and packet drops on one of the devices. Signed-off-by:
-
John Crispin authored
HW reset is triggered in the mtk_hw_init() function. There is no need to also reset the core during probe. Signed-off-by:
-
John Crispin authored
The code used to also support the PDMA engine, which had 2 packet pointers per descriptor. Because of this we had to divide the result by 2 and round it up. This is no longer needed as the code only supports QDMA. Signed-off-by:
-
John Crispin authored
The original commit failed to set watchdog_timeo. This patch sets watchdog_timeo to HZ. Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf-nextDavid S. Miller authored
Pablo Neira Ayuso says: ==================== Netfilter updates for net-next The following patchset contains the first batch of Netfilter updates for your net-next tree. 1) Define pr_fmt() in nf_conntrack, from Weongyo Jeong. 2) Define and register netfilter's afinfo for the bridge family, this comes in preparation for native nfqueue's bridge for nft, from Stephane Bryant. 3) Add new attributes to store layer 2 and VLAN headers to nfqueue, also from Stephane Bryant. 4) Parse new NFQA_VLAN and NFQA_L2HDR nfqueue netlink attributes coming from userspace, from Stephane Bryant. 5) Use net->ipv6.devconf_all->hop_limit instead of hardcoded hop_limit in IPv6 SYNPROXY, from Liping Zhang. 6) Remove unnecessary check for dst == NULL in nf_reject_ipv6, from Haishuang Yan. 7) Deinline ctnetlink event report functions, from Florian Westphal. ==================== Signed-off-by:
-
- 12 Apr, 2016 4 commits
-
-
Florian Westphal authored
Not performance critical, it is only invoked when an expectation is added/destroyed. While at it, kill unused nf_ct_expect_event() wrapper. Signed-off-by:
Florian Westphal <fw@strlen.de> Signed-off-by:
Pablo Neira Ayuso <pablo@netfilter.org>
-
Florian Westphal authored
Way too large; move it to nf_conntrack_ecache.c. Reduces total object size by 1216 byte on my machine. Signed-off-by:
-
David S. Miller authored
Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next Johan Hedberg says: ==================== pull request: bluetooth-next 2016-04-12 Here's a set of Bluetooth & 802.15.4 patches intended for the 4.7 kernel: - Fix for race condition in vhci driver - Memory leak fix for ieee802154/adf7242 driver - Improvements to deal with single-mode (LE-only) Bluetooth controllers - Fix for allowing the BT_SECURITY_FIPS security level - New BCM2E71 ACPI ID - NULL pointer dereference fix fox hci_ldisc driver Let me know if there are any issues pulling. Thanks. ==================== Signed-off-by:
-
Andrew Lunn authored
MDIO devices can be stacked upon each other. The current code supports two levels, which until recently has been enough for a DSA mdio bus on top of another bus. Now we have hardware which has an MDIO mux in the middle. Define an MDIO MUTEX class with three levels. Signed-off-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
-
- 11 Apr, 2016 7 commits
-
-
David S. Miller authored
David Howells says: ==================== RxRPC: 2nd rewrite part 1 Okay, I'm in the process of rewriting the RxRPC rewrite. The primary aim of this second rewrite is to strictly control the number of active connections we know about and to get rid of connections we don't need much more quickly. On top of this, there are fixes to the protocol handling which will all occur in later parts. Here's the first set of patches from the second go, aimed at net-next. These are all fixes and cleanups preparatory to the main event. Notable parts of this set include: (1) A fix for the AFS filesystem to wait for outstanding calls to complete before closing the RxRPC socket. (2) Differentiation of local and remote abort codes. At a future point userspace will get to see this via control message data on recvmsg(). (3) Absorb the rxkad module into the af_rxrpc module to prevent a dependency loop. (4) Create a null security module and unconditionalise calls into the security module that's in force (there will always be a security module applied to a connection, even if it's just the null one). ==================== Signed-off-by: -
David Howells authored
Create a null security type for security index 0 and get rid of all conditional calls to the security operations. We expect normally to be using security, so this should be of little negative impact. Signed-off-by:
David Howells <dhowells@redhat.com> Signed-off-by:
-
David Howells authored
Absorb the rxkad security module into the af_rxrpc module so that there's only one module file. This avoids a circular dependency whereby rxkad pins af_rxrpc and cached connections pin rxkad but can't be manually evicted (they will expire eventually and cease pinning). With this change, af_rxrpc can just be unloaded, despite having cached connections. Signed-off-by:
-
David Howells authored
Don't assume transport address family and size when using the peer address to send a packet. Instead, use the start of the transport address rather than any particular element of the union and use the transport address length noted inside the sockaddr_rxrpc struct. This will be necessary when IPv6 support is introduced. Signed-off-by:
-
David Howells authored
Don't pass gfp around in incoming call handling functions, but rather hard code it at the points where we actually need it since the value comes from within the rxrpc driver and is always the same. Signed-off-by:
-
David Howells authored
In the rxrpc_connection and rxrpc_call structs, there's one field to hold the abort code, no matter whether that value was generated locally to be sent or was received from the peer via an abort packet. Split the abort code fields in two for cleanliness sake and add an error field to hold the Linux error number to the rxrpc_call struct too (sometimes this is generated in a context where we can't return it to userspace directly). Furthermore, add a skb mark to indicate a packet that caused a local abort to be generated so that recvmsg() can pick up the correct abort code. A future addition will need to be to indicate to userspace the difference between aborts via a control message. Signed-off-by:
-
David Howells authored
Static arrays of strings should be const char *const[]. Signed-off-by:
-
