- 21 May, 2021 23 commits
-
-
Ioana Ciornei authored
Name the debugfs directory after the DPNI object instead of the netdev name since this can be changed after probe by udev rules. Signed-off-by:
Ioana Ciornei <ioana.ciornei@nxp.com> Reviewed-by:
Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Ioana Ciornei authored
When the DPNI object is connected to a DPMAC, setup the of_node to point to the DTS device node of that specific MAC. This enables other drivers, for example the DSA subsystem, to find the net_device by its device node. Signed-off-by:
-
David S. Miller authored
Vladimir Oltean says: ==================== Ethtool statistics counters cleanup for SJA1105 DSA driver This series removes some reported data from ethtool -S which were not counters at all, and reorganizes the code such that counters can be read individually and not just all at once. ==================== Signed-off-by: -
Vladimir Oltean authored
The current internal sja1105 driver API is optimized for retrieving many statistics counters at once. But the switch does not do atomic snapshotting for them anyway. In case we start reporting the hardware port counters through ndo_get_stats64 as well, not just ethtool, it would be good to be able to read individual port counters and not all of them. Additionally, since Arnd Bergmann's commit ae1804de ("dsa: sja1105: dynamically allocate stats structure"), sja1105_get_ethtool_stats allocates memory dynamically, since struct sja1105_port_status was deemed to consume too much stack memory. That is not ideal. The large structure is only needed because of the burst read. If we read statistics one by one, we can consume less memory, and we can avoid dynamic allocation. Additionally, latency-sensitive interfaces such as PTP operations (for phc2sys) might suffer if the SPI mutex is being held for too long, which happens in the case of SPI burst reads. By reading counters one by one, we give a chance for higher priority processes to preempt and take the SPI bus mutex for accessing the PTP clock. Signed-off-by:
-
Vladimir Oltean authored
The queue levels are not counters, but instead they represent the occupancy of the MAC TX queues. Having these in ethtool port counters is not helpful, so remove them. Signed-off-by:
-
Colin Ian King authored
In the unlikely event that rule_cnt is zero the variable ret is not assigned a value and function hclge_dbg_dump_fd_tcam can end up returning an unitialized value in ret. Fix this by explicitly setting ret to zero before the for-loop. Addresses-Coverity: ("Uninitialized scalar variable") Fixes: b5a0b70d ("net: hns3: refactor dump fd tcam of debugfs") Signed-off-by:Colin Ian King <colin.king@canonical.com> Signed-off-by:
-
zuoqilin authored
Change 'contol' to 'control'. Signed-off-by:
zuoqilin <zuoqilin@yulong.com> Signed-off-by:
-
Jiapeng Chong authored
Eliminate the follow smatch warning: drivers/net/phy/phy_device.c:2886 phy_probe() warn: inconsistent indenting. Reported-by:
Abaci Robot <abaci@linux.alibaba.com> Signed-off-by:
Jiapeng Chong <jiapeng.chong@linux.alibaba.com> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
-
Yang Yingliang authored
Fix the following kernel build warning when CONFIG_SFC_SRIOV is disabled: drivers/net/ethernet/sfc/farch.c: In function ‘efx_farch_dimension_resources’: drivers/net/ethernet/sfc/farch.c:1671:21: warning: variable ‘buftbl_min’ set but not used [-Wunused-but-set-variable] unsigned vi_count, buftbl_min, total_tx_channels; Signed-off-by:Yang Yingliang <yangyingliang@huawei.com> Signed-off-by:
-
Wang Hai authored
s/becase/because/ s/reqeusts/requests/ s/funcions/functions/ s/addreses/addresses/ Signed-off-by:
Wang Hai <wanghai38@huawei.com> Signed-off-by:
-
Wang Hai authored
s/patckets/packets/ s/avilable/available/ s/tbe/the/ Signed-off-by:
-
David S. Miller authored
Guangbin Huang says: ==================== net: wan: clean up some code style issues This patchset clean up some code style issues. ==================== Signed-off-by: -
Peng Li authored
Macro argument 'card' and 'port' may be better as '(card)' and '(port)' to avoid precedence issues. Signed-off-by:
Peng Li <lipeng321@huawei.com> Signed-off-by:
Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by:
-
Peng Li authored
Braces {} should be used on all arms of this statement. Signed-off-by: -
Peng Li authored
This patch removes some redundant blank lines. Signed-off-by:
-
Peng Li authored
Trailing statements should be on next line. Signed-off-by:
-
Peng Li authored
Add space required after that close brace '}'. Add space required before the open parenthesis '('. Signed-off-by: -
Peng Li authored
Fix the checkpatch error as "foo* bar" should be "foo *bar". Signed-off-by:
-
David S. Miller authored
Vladimir Oltean says: ==================== Adapt the sja1105 DSA driver to the SPI controller's transfer limits This series changes the SPI transfer procedure in sja1105 to take into consideration the buffer size limitations that the SPI controller driver might have. Changes in v2: Remove the driver's use of cs_change and send multiple, smaller SPI messages instead of a single large one. ==================== Signed-off-by: -
Vladimir Oltean authored
The static config of the sja1105 switch is a long stream of bytes which is programmed to the hardware in chunks (portions with the chip select continuously asserted) of max 256 bytes each. Each chunk is a spi_message composed of 2 spi_transfers: the buffer with the data and a preceding buffer with the SPI access header. Only that certain SPI controllers, such as the spi-sc18is602 I2C-to-SPI bridge, cannot keep the chip select asserted for that long. The spi_max_transfer_size() and spi_max_message_size() functions are how the controller can impose its hardware limitations upon the SPI peripheral driver. For the sja1105 driver to work with these controllers, both buffers must be smaller than the transfer limit, and their sum must be smaller than the message limit. Regression-tested on a switch connected to a controller with no limitations (spi-fsl-dspi) as well as with one with caps for both max_transfer_size and max_message_size (spi-sc18is602). Signed-off-by:
-
Vladimir Oltean authored
The sja1105 driver has been described by Mark Brown as "not using the [ SPI ] API at all idiomatically" due to the use of cs_change: https://patchwork.kernel.org/project/netdevbpf/patch/20210520135031.2969183-1-olteanv@gmail.com/ According to include/linux/spi/spi.h, the chip select is supposed to be asserted for the entire length of a SPI message, as long as cs_change is false for all member transfers. The cs_change flag changes the following: (i) When a non-final SPI transfer has cs_change = true, the chip select should temporarily deassert and then reassert starting with the next transfer. (ii) When a final SPI transfer has cs_change = true, the chip select should remain asserted until the following SPI message. The sja1105 driver only uses cs_change for its first property, to form a single SPI message whose layout can be seen below: this is an entire, single spi_message _______________________________________________________________________________________________ / \ +-------------+---------------+-------------+---------------+ ... +-------------+---------------+ | hdr_xfer[0] | chunk_xfer[0] | hdr_xfer[1] | chunk_xfer[1] | | hdr_xfer[n] | chunk_xfer[n] | +-------------+---------------+-------------+---------------+ ... +-------------+---------------+ cs_change false true false true false false ____________________________ _____________________________ _____________________________ CS line __/ \/ \ ... / \__ The fact of the matter is that spi_max_message_size() has an ambiguous meaning if any non-final transfer has cs_change = true. If the SPI master has a limitation in that it cannot keep the chip select asserted for more than, say, 200 bytes (like the spi-sc18is602), the normal thing for it to do is to implement .max_transfer_size and .max_message_size, and limit both to 200: in the "worst case" where cs_change is always false, then the controller can, indeed, not send messages larger than 200 bytes. But the fact that the SPI controller's max_message_size does not necessarily mean that we cannot send messages larger than that. Notably, if the SPI master special-cases the transfers with cs_change and treats every chip select toggling as an entirely new transaction, then a SPI message can easily exceed that limit. So there is a temptation to ignore the controller's reported max_message_size when using cs_change = true in non-final transfers. But that can lead to false conclusions. As Mark points out, the SPI controller might have a different kind of limitation with the max message size, that has nothing at all to do with how long it can keep the chip select asserted. For example, that might be the case if the device is able to offload the chip select changes to the hardware as part of the data stream, and it packs the entire stream of commands+data (corresponding to a SPI message) into a single DMA transfer that is itself limited in size. So the only thing we can do is avoid ambiguity by not using cs_change at all. Instead of sending a single spi_message, we now send multiple SPI messages as follows: spi_message 0 spi_message 1 spi_message n ____________________________ ___________________________ _____________________________ / \ / \ / \ +-------------+---------------+-------------+---------------+ ... +-------------+---------------+ | hdr_xfer[0] | chunk_xfer[0] | hdr_xfer[1] | chunk_xfer[1] | | hdr_xfer[n] | chunk_xfer[n] | +-------------+---------------+-------------+---------------+ ... +-------------+---------------+ cs_change false true false true false false ____________________________ _____________________________ _____________________________ CS line __/ \/ \ ... / \__ which is clearer because the max_message_size limit is now easier to enforce. What is transmitted on the wire stays, of course, the same. Additionally, because we send no more than 2 transfers at a time, we now avoid dynamic memory allocation too, which might be seen as an improvement by some. Signed-off-by:
-
Peter Geis authored
Add a driver for the Motorcomm yt8511 phy that will be used in the production Pine64 rk3566-quartz64 development board. It supports gigabit transfer speeds, rgmii, and 125mhz clk output. Signed-off-by:
Peter Geis <pgwipeout@gmail.com> Signed-off-by:
-
YueHaibing authored
Printing kernel pointers is discouraged because they might leak kernel memory layout. This fixes smatch warning: drivers/net/ethernet/xilinx/xilinx_emaclite.c:1191 xemaclite_of_probe() warn: argument 4 to %08lX specifier is cast from pointer Signed-off-by:
YueHaibing <yuehaibing@huawei.com> Signed-off-by:
-
- 20 May, 2021 17 commits
-
-
YueHaibing authored
Use DEVICE_ATTR_RW helper instead of plain DEVICE_ATTR, which makes the code a bit shorter and easier to read. Signed-off-by:
-
YueHaibing authored
Use DEVICE_ATTR_RO helper instead of plain DEVICE_ATTR, which makes the code a bit shorter and easier to read. Signed-off-by:
-
YueHaibing authored
Use DEVICE_ATTR_RO helper instead of plain DEVICE_ATTR, which makes the code a bit shorter and easier to read. Signed-off-by:
-
Po-Hsu Lin authored
When there is no devlink device, the following command will return: $ devlink -j dev show {dev:{}} This will cause IndexError when trying to access the first element in dev of this json dataset. Use the kselftest framework skip code to skip this test in this case. Example output with this change: # selftests: net: devlink_port_split.py # no devlink device was found, test skipped ok 7 selftests: net: devlink_port_split.py # SKIP Link: https://bugs.launchpad.net/bugs/1928889Signed-off-by:Po-Hsu Lin <po-hsu.lin@canonical.com> Signed-off-by:
-
Michal Suchanek authored
This way the compiler warns when a new value is added to the enum but not to the string translation like: drivers/net/ethernet/ibm/ibmvnic.c: In function 'adapter_state_to_string': drivers/net/ethernet/ibm/ibmvnic.c:832:2: warning: enumeration value 'VNIC_FOOBAR' not handled in switch [-Wswitch] switch (state) { ^~~~~~ drivers/net/ethernet/ibm/ibmvnic.c: In function 'reset_reason_to_string': drivers/net/ethernet/ibm/ibmvnic.c:1935:2: warning: enumeration value 'VNIC_RESET_FOOBAR' not handled in switch [-Wswitch] switch (reason) { ^~~~~~ Signed-off-by:Michal Suchanek <msuchanek@suse.de> Acked-by:
Lijun Pan <lijunp213@gmail.com> Link: https://lore.kernel.org/netdev/CAOhMmr701LecfuNM+EozqbiTxFvDiXjFdY2aYeKJYaXq9kqVDg@mail.gmail.com/Signed-off-by:
-
wengjianfeng authored
assign vlue (EIO/EPROTO) to variable r, and goto exit label, but just return r follow exit label, so we delete exit label, and just replace with return sentence. Signed-off-by:
wengjianfeng <wengjianfeng@yulong.com> Signed-off-by:
-
David S. Miller authored
Guangbin Huang says: ==================== net: bonding: clean up some code style issues This patchset cleans up some code style issues. ==================== Signed-off-by: -
Yufeng Mo authored
Code indent should use tabs where possible, so use tabs instead of space for code indent. Signed-off-by:
Yufeng Mo <moyufeng@huawei.com> Signed-off-by:
-
Yufeng Mo authored
Braces {} are not necessary for single statement blocks, so remove these braces {}. Signed-off-by: -
Yufeng Mo authored
Fix incorrect code indent for conditional statements. Signed-off-by:
-
Yufeng Mo authored
Add some blank lines after declarations as required. Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queueDavid S. Miller authored
Tony Nguyen says: ==================== 1GbE Intel Wired LAN Driver Updates 2021-05-20 This series contains updates to igc driver only. Andre Guedes says: This series adds AF_XDP zero-copy feature to igc driver. The initial patches do some code refactoring, preparing the code base to land the AF_XDP zero-copy feature, avoiding code duplications. The last patches of the series are the ones implementing the feature. The last patch which indeed implements AF_XDP zero-copy support was originally way too lengthy so, for the sake of code review, I broke it up into two patches: one adding support for the RX functionality and the other one adding TX support. --- v2: Patch 8/9 - "igc: Enable RX via AF_XDP zero-copy" * In XDP_PASS flow, copy metadata too into the skb. * When HW timestamp is added by the NIC, after copying it into a local variable, update xdp_buff->data_meta so that metadata length when XDP program is called 0. * In igc_xdp_enable_pool(), call xsk_pool_dma_unmap() on failure. Known issues: When an XDP application is running in Tx-Only mode with Zero-Copy enabled, it is not expected to add the frames to the fill-queue. I have noticed the following two issues in this scenario: - If XDP_USE_NEED_WAKEUP flag is not set by application, igc_poll() will go into infinite loop because the buffer allocation resulting in igc_clean_rx_irq_zc() indicating that all work is not done and NAPI should keep polling. This does not occur if XDP_USE_NEED_WAKEUP flag is set. - Since there are no buffers allocated by userspace for the fill queue, there is no memory allocated for the NIC to copy the data to. If the packet received is destined to the hardware queue where XDP application is running, no packets are received even on other queues. Both these issues can be mitigated by adding a few frames to the fill queue. The second issue can also be mitigated by making sure no packets are being received on the hardware queue where Rx is running. ==================== Signed-off-by: -
David S. Miller authored
Hui Tang says: ==================== net: remove leading spaces before tabs There are a few leading spaces before tabs and remove it by running the following commard: $ find . -name '*.[ch]' | xargs sed -r -i 's/^[ ]+\t/\t/' ==================== Signed-off-by: -
Hui Tang authored
There are a few leading spaces before tabs and remove it by running the following commard: $ find . -name '*.[ch]' | xargs sed -r -i 's/^[ ]+\t/\t/' Signed-off-by:Hui Tang <tanghui20@huawei.com> Signed-off-by:
-
Hui Tang authored
There are a few leading spaces before tabs and remove it by running the following commard: $ find . -name '*.[ch]' | xargs sed -r -i 's/^[ ]+\t/\t/' Signed-off-by: -
Hui Tang authored
There are a few leading spaces before tabs and remove it by running the following commard: $ find . -name '*.[ch]' | xargs sed -r -i 's/^[ ]+\t/\t/' Cc: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: -
Hui Tang authored
There are a few leading spaces before tabs and remove it by running the following commard: $ find . -name '*.[ch]' | xargs sed -r -i 's/^[ ]+\t/\t/' Cc: Lee Jones <lee.jones@linaro.org> Signed-off-by:
-
