- 17 Jun, 2021 37 commits
-
-
Erik Rosen authored
Add hardware monitoring support for Flex power interface modules PIM4006, PIM4328 and PIM4820. Signed-off-by:
Erik Rosen <erik.rosen@metormote.com> Signed-off-by:
Guenter Roeck <linux@roeck-us.net>
-
Erik Rosen authored
Allow the use of a phase function even if it does not exist on the associated page. Signed-off-by:
-
Erik Rosen authored
Add support for reading and decoding direct format coefficients to the PMBus core driver. If the new flag PMBUS_USE_COEFFICIENTS_CMD is set, the driver will use the COEFFICIENTS register together with the information in the pmbus_sensor_attr structs to initialize relevant coefficients for the direct mode format. Signed-off-by:
-
Erik Rosen authored
Some PMBus chips respond with invalid data when reading the WRITE_PROTECT register. For such chips, this flag should be set so that the PMBus core driver doesn't use the WRITE_PROTECT command to determine its behavior. Signed-off-by:
-
Mauro Carvalho Chehab authored
The :doc:`foo` tag is auto-generated via automarkup.py. So, use the filename at the sources, instead of :doc:`foo`. Signed-off-by:
Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Link: https://lore.kernel.org/r/32b0db7e79a3ed0e817213113c607a1b819e3867.1622898327.git.mchehab+huawei@kernel.orgSigned-off-by:
-
Madhava Reddy Siddareddygari authored
Currently, for Packet Error Checking (PEC) only the controller is checked for support. This causes problems on the cisco-8000 platform where a SMBUS transaction errors are observed. This is because PEC has to be enabled only if both controller and adapter support it. Added code to check PEC capability for adapter and enable it only if both controller and adapter supports PEC. Signed-off-by:
Madhava Reddy Siddareddygari <msiddare@cisco.com> [Upstream from SONiC https://github.com/Azure/sonic-linux-kernel/pull/215] Signed-off-by:
Paul Menzel <pmenzel@molgen.mpg.de> Link: https://lore.kernel.org/r/20210605052700.541455-1-pmenzel@molgen.mpg.de [groeck: Dropped unnecessary continuation line] Signed-off-by:
-
Ninad Malwade authored
As per current logic the wait time per conversion is arouns 430ms for 512 samples and around 860ms for 1024 samples for 3 channels considering 140us as the bus voltage and shunt voltage sampling conversion time. This waiting time is a lot for the continuous mode and even for the single shot mode. For continuous mode when moving average is considered the waiting for CVRF bit is not required and the data from the previous conversion is sufficuent. As mentioned in the datasheet the conversion ready bit is provided to help coordinate single-shot conversions, we can restrict the use to single-shot mode only. Also, the conversion time is for the averaged samples, the wait time for the polling can omit the number of samples consideration. Signed-off-by:
Ninad Malwade <nmalwade@nvidia.com> Link: https://lore.kernel.org/r/1622789683-30931-1-git-send-email-nmalwade@nvidia.comSigned-off-by:
-
Guenter Roeck authored
If a fan is not running or not connected, of if fan monitoring is disabled, the fan count register returns a fixed value of 0xffe0. So far this is then translated to a RPM value larger than 0. Since this is misleading and does not really make much sense, report a fan RPM of 0 in this situation. Cc: Jan Kundrát <jan.kundrat@cesnet.cz> Cc: Václav Kubernát <kubernat@cesnet.cz> Signed-off-by:
Václav Kubernát <kubernat@cesnet.cz> Link: https://lore.kernel.org/r/20210526154022.3223012-7-linux@roeck-us.net
-
Guenter Roeck authored
Fault bits in MAX31790 are sticky and have to be cleared explicitly. A write operation into either the 'Target Duty Cycle' register or the 'Target Count' register is necessary to clear a fault. At the same time, we can never clear cached fault status values before reading them because the companion fault status for any given fan is cleared as well when clearing a fault. Cc: Jan Kundrát <jan.kundrat@cesnet.cz> Cc: Václav Kubernát <kubernat@cesnet.cz> Signed-off-by:
-
Guenter Roeck authored
pwmX_enable supports three possible values: 0: Fan control disabled. Duty cycle is fixed to 0% 1: Fan control enabled, pwm mode. Duty cycle is determined by values written into Target Duty Cycle registers. 2: Fan control enabled, rpm mode Duty cycle is adjusted such that fan speed matches the values in Target Count registers The current code does not do this; instead, it mixes pwm control configuration with fan speed monitoring configuration. Worse, it reports that pwm control would be disabled (pwmX_enable==0) when it is in fact enabled in pwm mode. Part of the problem may be that the chip sets the "TACH input enable" bit on its own whenever the mode bit is set to RPM mode, but that doesn't mean that "TACH input enable" accurately reflects the pwm mode. Fix it up and only handle pwm control with the pwmX_enable attributes. In the documentation, clarify that disabling pwm control (pwmX_enable=0) sets the pwm duty cycle to 0%. In the code, explain why TACH_INPUT_EN is set together with RPM_MODE. While at it, only update the configuration register if the configuration has changed, and only update the cached configuration if updating the chip configuration was successful. Cc: Jan Kundrát <jan.kundrat@cesnet.cz> Cc: Václav Kubernát <kubernat@cesnet.cz> Signed-off-by:
Jan Kundrát <jan.kundrat@cesnet.cz> Link: https://lore.kernel.org/r/20210526154022.3223012-4-linux@roeck-us.net
-
Guenter Roeck authored
The MAX31790 has two sets of registers for pwm duty cycles, one to request a duty cycle and one to read the actual current duty cycle. Both do not have to be the same. When reporting the pwm duty cycle to the user, the actual pwm duty cycle from pwm duty cycle registers needs to be reported. When setting it, the pwm target duty cycle needs to be written. Since we don't know the actual pwm duty cycle after a target pwm duty cycle has been written, set the valid flag to false to indicate that actual pwm duty cycle should be read from the chip instead of using cached values. Cc: Jan Kundrát <jan.kundrat@cesnet.cz> Cc: Václav Kubernát <kubernat@cesnet.cz> Signed-off-by:
Václav Kubernát <kubernat@ceesnet.cz> Reviewed-by:
-
Guenter Roeck authored
Fans 7..12 do not have their own set of configuration registers. So far the code ignored that and read beyond the end of the configuration register range to get the tachometer period. This resulted in more or less random fan speed values for those fans. The datasheet is quite vague when it comes to defining the tachometer period for fans 7..12. Experiments confirm that the period is the same for both fans associated with a given set of configuration registers. Fixes: 54187ff9 ("hwmon: (max31790) Convert to use new hwmon registration API") Fixes: 195a4b42 ("hwmon: Driver for Maxim MAX31790") Cc: Jan Kundrát <jan.kundrat@cesnet.cz> Reviewed-by:
-
Joe Perches authored
Kernel doc for sht4x_read_values() shows 0 on success, 1 on failure but the return value on success is actually always positive as it is set to SHT4X_RESPONSE_LENGTH by a successful call to i2c_master_recv(). Miscellanea: o Update the kernel doc for sht4x_read_values to 0 for success or -ERRNO o Remove incorrectly used kernel doc /** header for other _read functions o Typo fix succesfull->successful o Reverse a test to unindent a block and use goto unlock o Declare cmd[SHT4X_CMD_LEN] rather than cmd[] At least for gcc 10.2, object size is reduced a tiny bit. $ size drivers/hwmon/sht4x.o* text data bss dec hex filename 1752 404 256 2412 96c drivers/hwmon/sht4x.o.new 1825 404 256 2485 9b5 drivers/hwmon/sht4x.o.old Signed-off-by:
Joe Perches <joe@perches.com> Link: https://lore.kernel.org/r/60eedce497137eb34448c0c77e01ec9d9c972ad7.camel@perches.com Reviewed by: Navin Sankar Velliangiri <navin@linumiz.com> Signed-off-by:
-
Navin Sankar Velliangiri authored
This patch adds a hwmon driver for the SHT4x Temperature and Humidity sensor. Signed-off-by:
Navin Sankar Velliangiri <navin@linumiz.com> [groeck: dropped unnecessary empty line and continuation lines] Signed-off-by:
-
Fabio Estevam authored
The entry for mp2888 is missing and it causes the following 'make htmldocs' build warning: Documentation/hwmon/mp2888.rst: WARNING: document isn't included in any toctree Add the mp2888 entry. Signed-off-by:
Fabio Estevam <festevam@gmail.com> Link: https://lore.kernel.org/r/20210521172218.37592-1-festevam@gmail.comSigned-off-by:
-
Chu Lin authored
adm1272 supports temperature reporting but it is disabled by default. Tested: ls temp1_* temp1_crit temp1_highest temp1_max temp1_crit_alarm temp1_input temp1_max_alarm cat temp1_input 26642 Signed-off-by:
Chu Lin <linchuyuan@google.com> Link: https://lore.kernel.org/r/20210512171043.2433694-1-linchuyuan@google.com [groeck: Updated subject to reflect correct driver] Signed-off-by:
-
Vadim Pasternak authored
Monolithic Power Systems, Inc. (MPS) dual-loop, digital, multi-phase controller. Signed-off-by:
Vadim Pasternak <vadimp@nvidia.com> Acked-by:
Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/20210511055619.118104-4-vadimp@nvidia.comSigned-off-by:
-
Vadim Pasternak authored
Add support for mp2888 device from Monolithic Power Systems, Inc. (MPS) vendor. This is a digital, multi-phase, pulse-width modulation controller. This device supports: - One power rail. - Programmable Multi-Phase up to 10 Phases. - PWM-VID Interface - One pages 0 for telemetry. - Programmable pins for PMBus Address. - Built-In EEPROM to Store Custom Configurations. - Can configured VOUT readout in direct or VID format and allows setting of different formats on rails 1 and 2. For VID the following protocols are available: VR13 mode with 5-mV DAC; VR13 mode with 10-mV DAC, IMVP9 mode with 5-mV DAC. Signed-off-by:
kernel test robot <lkp@intel.com> Link: https://lore.kernel.org/r/20210511055619.118104-3-vadimp@nvidia.com [groeck: Add MODULE_IMPORT_NS] Signed-off-by:
-
Vadim Pasternak authored
Increase maximum number of phases from 8 to 10 to support multi-phase devices allowing up to 10 phases. Signed-off-by:
-
Zhen Lei authored
When devm_ioremap_resource() fails, a clear enough error message will be printed by its subfunction __devm_ioremap_resource(). The error information contains the device name, failure cause, and possibly resource information. Therefore, remove the error printing here to simplify code and reduce the binary size. Reported-by:
Hulk Robot <hulkci@huawei.com> Signed-off-by:
Zhen Lei <thunder.leizhen@huawei.com> Link: https://lore.kernel.org/r/20210511091843.4561-1-thunder.leizhen@huawei.comSigned-off-by:
-
Erik Rosen authored
Add support for Flex BMR310, BMR456, BMR457, BMR458, BMR480, BMR490, BMR491 and BMR492 to the pmbus driver Signed-off-by:
-
Erik Rosen authored
Add documentation for the new pmbus flags PMBUS_WRITE_PROTECTED, PMBUS_NO_CAPABILITY and PMBUS_READ_STATUS_AFTER_FAILED_CHECK Signed-off-by:
-
Erik Rosen authored
Some PMBus chips end up in an undefined state when trying to read an unsupported register. For such chips, it is necessary to reset the chip pmbus controller to a known state after a failed register check. This can be done by reading a known register. By setting this flag the driver will try to read the STATUS register after each failed register check. This read may fail, but it will put the chip into a known state. Signed-off-by:
-
Armin Wolf authored
Use platform_device_register_simple() instead of manually calling platform_device_alloc()/platform_device_add(). Signed-off-by:
Armin Wolf <W_Armin@gmx.de> Link: https://lore.kernel.org/r/20210508131457.12780-5-W_Armin@gmx.deReviewed-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
-
Armin Wolf authored
Use watchdog_set_nowayout() to process param setting and change param type to bool. Signed-off-by:
-
Armin Wolf authored
strlcpy is considered deprecated. Replace it with strscpy. Signed-off-by:
-
Armin Wolf authored
Use devm_kzalloc()/devm_watchdog_register() for watchdog registration since it allows us to remove the sch56xx_watchdog_data struct from the drivers own data structs. Remove sch56xx_watchdog_unregister since devres takes care of that now. Signed-off-by:
-
Andy Shevchenko authored
Use SPI_MODE_X_MASK instead of open coded variant. Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20210510141331.56736-1-andriy.shevchenko@linux.intel.comSigned-off-by:
-
Guenter Roeck authored
Valid Maxim Integrated ACPI device IDs would start with MXIM, not with MAX1. On top of that, ACPI device IDs reflecting chip names are almost always invalid. Remove the invalid ACPI IDs. Fixes: 04e1e70a ("hwmon: (max31722) Add support for MAX31722/MAX31723 temperature sensors") Signed-off-by:
-
Guenter Roeck authored
This reverts commit b58bd4c6. None of the ACPI IDs introduced with the reverted patch is a valid ACPI device ID. Any ACPI users of this driver are advised to use PRP0001 and a devicetree-compatible device identification. Fixes: b58bd4c6 ("hwmon: (lm70) Add support for ACPI") Cc: Andrej Picej <andpicej@gmail.com> Signed-off-by:
-
Mauro Carvalho Chehab authored
While UTF-8 characters can be used at the Linux documentation, the best is to use them only when ASCII doesn't offer a good replacement. So, replace the occurences of the following UTF-8 characters: - U+2010 ('‐'): HYPHEN - U+2013 ('–'): EN DASH - U+2019 ('’'): RIGHT SINGLE QUOTATION MARK Signed-off-by: -
Mauro Carvalho Chehab authored
The conversion tools used during DocBook/LaTeX/html/Markdown->ReST conversion and some cut-and-pasted text contain some characters that aren't easily reachable on standard keyboards and/or could cause troubles when parsed by the documentation build system. Replace the occurences of the following characters: - U+2010 ('‐'): HYPHEN as ASCII HYPHEN is preferred over U+2010 Signed-off-by: -
Robert Marko authored
Document the DT compatible for TI TMP1075 which is a LM75 compatible sensor. Signed-off-by:
Robert Marko <robert.marko@sartura.hr> Link: https://lore.kernel.org/r/20210429121150.106804-2-robert.marko@sartura.hrAcked-by:
-
Robert Marko authored
TI TMP1075 is a LM75 compatible sensor, so lets add support for it. Signed-off-by:
-
Erik Rosen authored
Update documentation for zl6100 driver and fix dead links to technical specifications Signed-off-by:
-
Erik Rosen authored
Add support for Renesas ZL8802 Dual Channel/Dual Phase PMBus DC/DC Digital Controller as well as ZLS1003 and ZLS4009 custom DC/DC controller chips. Signed-off-by:
-
Chris Packham authored
The BPA-RS600 doesn't follow the PMBus spec for linear data. Specifically it treats the mantissa as an unsigned 11-bit value instead of a two's complement 11-bit value. At this point it's unclear whether this only affects Vin or if Pin/Pout1 are affected as well. Erring on the side of caution only Vin is dealt with here. Fixes: 15b2703e ("hwmon: (pmbus) Add driver for BluTek BPA-RS600") Signed-off-by:
Chris Packham <chris.packham@alliedtelesis.co.nz> Link: https://lore.kernel.org/r/20210616034218.25821-1-chris.packham@alliedtelesis.co.nzSigned-off-by:
-
- 13 Jun, 2021 3 commits
-
-
Linus Torvalds authored
-
Linus Torvalds authored
Merge tag 'perf-tools-fixes-for-v5.13-2021-06-13' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux Pull perf tools fixes from Arnaldo Carvalho de Melo: - Correct buffer copying when peeking events - Sync cpufeatures/disabled-features.h header with the kernel sources * tag 'perf-tools-fixes-for-v5.13-2021-06-13' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux: tools headers cpufeatures: Sync with the kernel sources perf session: Correct buffer copying when peeking events
-
git://git.linux-nfs.org/projects/trondmy/linux-nfsLinus Torvalds authored
Pull NFS client bugfixes from Trond Myklebust: "Highlights include: Stable fixes: - Fix use-after-free in nfs4_init_client() Bugfixes: - Fix deadlock between nfs4_evict_inode() and nfs4_opendata_get_inode() - Fix second deadlock in nfs4_evict_inode() - nfs4_proc_set_acl should not change the value of NFS_CAP_UIDGID_NOMAP - Fix setting of the NFS_CAP_SECURITY_LABEL capability" * tag 'nfs-for-5.13-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: NFSv4: Fix second deadlock in nfs4_evict_inode() NFSv4: Fix deadlock between nfs4_evict_inode() and nfs4_opendata_get_inode() NFS: FMODE_READ and friends are C macros, not enum types NFS: Fix a potential NULL dereference in nfs_get_client() NFS: Fix use-after-free in nfs4_init_client() NFS: Ensure the NFS_CAP_SECURITY_LABEL capability is set when appropriate NFSv4: nfs4_proc_set_acl needs to restore NFS_CAP_UIDGID_NOMAP on error.
-
