If ipv4_valdiate_peer() fails during a cached entry lookup,
we'll NULL derer since the loop iterator assumes rth is not
NULL.

Letting this be handled as a failure is just bogus, so just make it
not fail.  If we have trouble getting a non-NULL neighbour for the
redirected gateway, just restore the original gateway and continue.

The very next use of this cached route will try again.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem

__mkroute_output fails to work with the original tos
and uses value with stripped RTO_ONLINK bit. Make sure we put
the original TOS bits into rt_key_tos because it used to match
cached route.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current default watchdog timer is enabled, but we are seeing issues on
legacy devices. So change the default setting of watchdog timer to per
device based. But user still can use the "wd_disable" module parameter
to overwrite the system setting

Cc: stable@vger.kernel.org #3.0+
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The ht40 setting should not change after association unless channel switch

This fix a problem we are seeing which cause uCode assert because driver
sending invalid information and make uCode confuse

Here is the firmware assert message:
kernel: iwlagn 0000:03:00.0: Microcode SW error detected.  Restarting 0x82000000.
kernel: iwlagn 0000:03:00.0: Loaded firmware version: 17.168.5.3 build 42301
kernel: iwlagn 0000:03:00.0: Start IWL Error Log Dump:
kernel: iwlagn 0000:03:00.0: Status: 0x000512E4, count: 6
kernel: iwlagn 0000:03:00.0: 0x00002078 | ADVANCED_SYSASSERT
kernel: iwlagn 0000:03:00.0: 0x00009514 | uPc
kernel: iwlagn 0000:03:00.0: 0x00009496 | branchlink1
kernel: iwlagn 0000:03:00.0: 0x00009496 | branchlink2
kernel: iwlagn 0000:03:00.0: 0x0000D1F2 | interruptlink1
kernel: iwlagn 0000:03:00.0: 0x00000000 | interruptlink2
kernel: iwlagn 0000:03:00.0: 0x01008035 | data1
kernel: iwlagn 0000:03:00.0: 0x0000C90F | data2
kernel: iwlagn 0000:03:00.0: 0x000005A7 | line
kernel: iwlagn 0000:03:00.0: 0x5080B520 | beacon time
kernel: iwlagn 0000:03:00.0: 0xCC515AE0 | tsf low
kernel: iwlagn 0000:03:00.0: 0x00000003 | tsf hi
kernel: iwlagn 0000:03:00.0: 0x00000000 | time gp1
kernel: iwlagn 0000:03:00.0: 0x29703BF0 | time gp2
kernel: iwlagn 0000:03:00.0: 0x00000000 | time gp3
kernel: iwlagn 0000:03:00.0: 0x000111A8 | uCode version
kernel: iwlagn 0000:03:00.0: 0x000000B0 | hw version
kernel: iwlagn 0000:03:00.0: 0x00480303 | board version
kernel: iwlagn 0000:03:00.0: 0x09E8004E | hcmd
kernel: iwlagn 0000:03:00.0: CSR values:
kernel: iwlagn 0000:03:00.0: (2nd byte of CSR_INT_COALESCING is CSR_INT_PERIODIC_REG)
kernel: iwlagn 0000:03:00.0:        CSR_HW_IF_CONFIG_REG: 0X00480303
kernel: iwlagn 0000:03:00.0:          CSR_INT_COALESCING: 0X0000ff40
kernel: iwlagn 0000:03:00.0:                     CSR_INT: 0X00000000
kernel: iwlagn 0000:03:00.0:                CSR_INT_MASK: 0X00000000
kernel: iwlagn 0000:03:00.0:           CSR_FH_INT_STATUS: 0X00000000
kernel: iwlagn 0000:03:00.0:                 CSR_GPIO_IN: 0X00000030
kernel: iwlagn 0000:03:00.0:                   CSR_RESET: 0X00000000
kernel: iwlagn 0000:03:00.0:                CSR_GP_CNTRL: 0X080403c5
kernel: iwlagn 0000:03:00.0:                  CSR_HW_REV: 0X000000b0
kernel: iwlagn 0000:03:00.0:              CSR_EEPROM_REG: 0X07d60ffd
kernel: iwlagn 0000:03:00.0:               CSR_EEPROM_GP: 0X90000001
kernel: iwlagn 0000:03:00.0:              CSR_OTP_GP_REG: 0X00030001
kernel: iwlagn 0000:03:00.0:                 CSR_GIO_REG: 0X00080044
kernel: iwlagn 0000:03:00.0:            CSR_GP_UCODE_REG: 0X000093bb
kernel: iwlagn 0000:03:00.0:           CSR_GP_DRIVER_REG: 0X00000000
kernel: iwlagn 0000:03:00.0:           CSR_UCODE_DRV_GP1: 0X00000000
kernel: iwlagn 0000:03:00.0:           CSR_UCODE_DRV_GP2: 0X00000000
kernel: iwlagn 0000:03:00.0:                 CSR_LED_REG: 0X00000078
kernel: iwlagn 0000:03:00.0:        CSR_DRAM_INT_TBL_REG: 0X88214dd2
kernel: iwlagn 0000:03:00.0:        CSR_GIO_CHICKEN_BITS: 0X27800200
kernel: iwlagn 0000:03:00.0:             CSR_ANA_PLL_CFG: 0X00000000
kernel: iwlagn 0000:03:00.0:           CSR_HW_REV_WA_REG: 0X0001001a
kernel: iwlagn 0000:03:00.0:        CSR_DBG_HPET_MEM_REG: 0Xffff0010
kernel: iwlagn 0000:03:00.0: FH register values:
kernel: iwlagn 0000:03:00.0:         FH_RSCSR_CHNL0_STTS_WPTR_REG: 0X21316d00
kernel: iwlagn 0000:03:00.0:        FH_RSCSR_CHNL0_RBDCB_BASE_REG: 0X021479c0
kernel: iwlagn 0000:03:00.0:                  FH_RSCSR_CHNL0_WPTR: 0X00000060
kernel: iwlagn 0000:03:00.0:         FH_MEM_RCSR_CHNL0_CONFIG_REG: 0X80819104
kernel: iwlagn 0000:03:00.0:          FH_MEM_RSSR_SHARED_CTRL_REG: 0X000000fc
kernel: iwlagn 0000:03:00.0:            FH_MEM_RSSR_RX_STATUS_REG: 0X07030000
kernel: iwlagn 0000:03:00.0:    FH_MEM_RSSR_RX_ENABLE_ERR_IRQ2DRV: 0X00000000
kernel: iwlagn 0000:03:00.0:                FH_TSSR_TX_STATUS_REG: 0X07ff0001
kernel: iwlagn 0000:03:00.0:                 FH_TSSR_TX_ERROR_REG: 0X00000000
kernel: iwlagn 0000:03:00.0: Start IWL Event Log Dump: display last 20 entries
kernel: ------------[ cut here ]------------
WARNING: at net/mac80211/util.c:1208 ieee80211_reconfig+0x1f1/0x407()
kernel: Hardware name: 4290W4H
kernel: Pid: 1896, comm: kworker/0:0 Not tainted 3.1.0 #2
kernel: Call Trace:
kernel:  [<ffffffff81036558>] ? warn_slowpath_common+0x73/0x87
kernel:  [<ffffffff813b8966>] ? ieee80211_reconfig+0x1f1/0x407
kernel:  [<ffffffff8139e8dc>] ? ieee80211_recalc_smps_work+0x32/0x32
kernel:  [<ffffffff8139e95a>] ? ieee80211_restart_work+0x7e/0x87
kernel:  [<ffffffff810472fa>] ? process_one_work+0x1c8/0x2e3
kernel:  [<ffffffff810480c9>] ? worker_thread+0x17a/0x23a
kernel:  [<ffffffff81047f4f>] ? manage_workers.clone.18+0x15b/0x15b
kernel:  [<ffffffff81047f4f>] ? manage_workers.clone.18+0x15b/0x15b
kernel:  [<ffffffff8104ba97>] ? kthread+0x7a/0x82
kernel:  [<ffffffff813d21b4>] ? kernel_thread_helper+0x4/0x10
kernel:  [<ffffffff8104ba1d>] ? kthread_flush_work_fn+0x11/0x11
kernel:  [<ffffffff813d21b0>] ? gs_change+0xb/0xb

Cc: <stable@kernel.org> 3.1+
Reported-by: Udo Steinberg <udo@hypervisor.org>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Group keys in IBSS or AP mode are not programmed
into the device since we give the key to it with
every TX packet. However, we do need mac80211 to
create the MMIC & PN in all cases. Move the code
around to set the key flags all the time. We set
them even when the key is removed again but that
is obviously harmless.

Cc: stable@vger.kernel.org
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (73 commits)
  netfilter: Remove ADVANCED dependency from NF_CONNTRACK_NETBIOS_NS
  ipv4: flush route cache after change accept_local
  sch_red: fix red_change
  Revert "udp: remove redundant variable"
  bridge: master device stuck in no-carrier state forever when in user-stp mode
  ipv4: Perform peer validation on cached route lookup.
  net/core: fix rollback handler in register_netdevice_notifier
  sch_red: fix red_calc_qavg_from_idle_time
  bonding: only use primary address for ARP
  ipv4: fix lockdep splat in rt_cache_seq_show
  sch_teql: fix lockdep splat
  net: fec: Select the FEC driver by default for i.MX SoCs
  isdn: avoid copying too long drvid
  isdn: make sure strings are null terminated
  netlabel: Fix build problems when IPv6 is not enabled
  sctp: better integer overflow check in sctp_auth_create_key()
  sctp: integer overflow in sctp_auth_create_key()
  ipv6: Set mcast_hops to IPV6_DEFAULT_MCASTHOPS when -1 was given.
  net: Fix corruption in /proc/*/net/dev_mcast
  mac80211: fix race between the AGG SM and the Tx data path
  ...

firewalld in Fedora 16 needs this.
Signed-off-by: David S. Miller <davem@davemloft.net>

After reset ipv4_devconf->data[IPV4_DEVCONF_ACCEPT_LOCAL] to 0,
we should flush route cache, or it will continue receive packets with local
source address, which should be dropped.
Signed-off-by: Weiping Pan <panweiping3@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Le mercredi 30 novembre 2011 à 14:36 -0800, Stephen Hemminger a écrit :

> (Almost) nobody uses RED because they can't figure it out.
> According to Wikipedia, VJ says that:
>  "there are not one, but two bugs in classic RED."

RED is useful for high throughput routers, I doubt many linux machines
act as such devices.

I was considering adding Adaptative RED (Sally Floyd, Ramakrishna
Gummadi, Scott Shender), August 2001

In this version, maxp is dynamic (from 1% to 50%), and user only have to
setup min_th (target average queue size)
(max_th and wq (burst in linux RED) are automatically setup)

By the way it seems we have a small bug in red_change()

if (skb_queue_empty(&sch->q))
	red_end_of_idle_period(&q->parms);

First, if queue is empty, we should call
red_start_of_idle_period(&q->parms);

Second, since we dont use anymore sch->q, but q->qdisc, the test is
meaningless.

Oh well...

[PATCH] sch_red: fix red_change()

Now RED is classful, we must check q->qdisc->q.qlen, and if queue is empty,
we start an idle period, not end it.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2: (31 commits)
  ocfs2: avoid unaligned access to dqc_bitmap
  ocfs2: Use filemap_write_and_wait() instead of write_inode_now()
  ocfs2: honor O_(D)SYNC flag in fallocate
  ocfs2: Add a missing journal credit in ocfs2_link_credits() -v2
  ocfs2: send correct UUID to cleancache initialization
  ocfs2: Commit transactions in error cases -v2
  ocfs2: make direntry invalid when deleting it
  fs/ocfs2/dlm/dlmlock.c: free kmem_cache_zalloc'd data using kmem_cache_free
  ocfs2: Avoid livelock in ocfs2_readpage()
  ocfs2: serialize unaligned aio
  ocfs2: Implement llseek()
  ocfs2: Fix ocfs2_page_mkwrite()
  ocfs2: Add comment about orphan scanning
  ocfs2: Clean up messages in the fs
  ocfs2/cluster: Cluster up now includes network connections too
  ocfs2/cluster: Add new function o2net_fill_node_map()
  ocfs2/cluster: Fix output in file elapsed_time_in_ms
  ocfs2/dlm: dlmlock_remote() needs to account for remastery
  ocfs2/dlm: Take inflight reference count for remotely mastered resources too
  ocfs2/dlm: Cleanup dlm_wait_for_node_death() and dlm_wait_for_node_recovery()
  ...

The dqc_bitmap field of struct ocfs2_local_disk_chunk is 32-bit aligned,
but not 64-bit aligned.  The dqc_bitmap is accessed by ocfs2_set_bit(),
ocfs2_clear_bit(), ocfs2_test_bit(), or ocfs2_find_next_zero_bit().  These
are wrapper macros for ext2_*_bit() which need to take an unsigned long
aligned address (though some architectures are able to handle unaligned
address correctly)

So some 64bit architectures may not be able to access the dqc_bitmap
correctly.

This avoids such unaligned access by using another wrapper functions for
ext2_*_bit().  The code is taken from fs/ext4/mballoc.c which also need to
handle unaligned bitmap access.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Joel Becker <jlbec@evilplan.org>
Cc: Mark Fasheh <mfasheh@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Joel Becker <jlbec@evilplan.org>

* 'fixes' of http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm:
  ARM: 7182/1: ARM cpu topology: fix warning
  ARM: 7181/1: Restrict kprobes probing SWP instructions to ARMv5 and below
  ARM: 7180/1: Change kprobes testcase with unpredictable STRD instruction
  ARM: 7177/1: GIC: avoid skipping non-existent PPIs in irq_start calculation
  ARM: 7176/1: cpu_pm: register GIC PM notifier only once
  ARM: 7175/1: add subname parameter to mfp_set_groupg callers
  ARM: 7174/1: Fix build error in kprobes test code on Thumb2 kernels
  ARM: 7172/1: dma: Drop GFP_COMP for DMA memory allocations
  ARM: 7171/1: unwind: add unwind directives to bitops assembly macros
  ARM: 7170/2: fix compilation breakage in entry-armv.S
  ARM: 7168/1: use cache type functions for arch_get_unmapped_area
  ARM: perf: check that we have a platform device when reserving PMU
  ARM: 7166/1: Use PMD_SHIFT instead of PGDIR_SHIFT in dma-consistent.c
  ARM: 7165/2: PL330: Fix typo in _prepare_ccr()
  ARM: 7163/2: PL330: Only register usable channels
  ARM: 7162/1: errata: tidy up Kconfig options for PL310 errata workarounds
  ARM: 7161/1: errata: no automatic store buffer drain
  ARM: perf: initialise used_mask for fake PMU during validation
  ARM: PMU: remove pmu_init declaration
  ARM: PMU: re-export release_pmu symbol to modules

This reverts commit 81d54ec8.

If we take the "try_again" goto, due to a checksum error,
the 'len' has already been truncated.  So we won't compute
the same values as the original code did.
Reported-by: paul bilke <fsmail@conspiracy.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

When in user-stp mode, bridge master do not follow state of its slaves, so
after the following sequence of events it can stuck forever in no-carrier
state:
1) turn stp off
2) put all slaves down - master device will follow their state and also go in
no-carrier state
3) turn stp on with bridge-stp script returning 0 (go to the user-stp mode)
Now bridge master won't follow slaves' state and will never reach running
state.

This patch solves the problem by making user-stp and kernel-stp behavior
similar regarding master following slaves' states.
Signed-off-by: Vitalii Demianets <vitas@nppfactor.kiev.ua>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Otherwise we won't notice the peer GENID change.
Reported-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Btrfs: fix meta data raid-repair merge problem
  Btrfs: skip allocation attempt from empty cluster
  Btrfs: skip block groups without enough space for a cluster
  Btrfs: start search for new cluster at the beginning
  Btrfs: reset cluster's max_size when creating bitmap
  Btrfs: initialize new bitmaps' list
  Btrfs: fix oops when calling statfs on readonly device
  Btrfs: Don't error on resizing FS to same size
  Btrfs: fix deadlock on metadata reservation when evicting a inode
  Fix URL of btrfs-progs git repository in docs
  btrfs scrub: handle -ENOMEM from init_ipath()

This reverts commit f785d83a.

This was provoking WARNINGs from the iwlegacy drivers.
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Commit 4a54c8c1 introduced raid-repair, killing the individual
readpage_io_failed_hook entries from inode.c and disk-io.c. Commit
4bb31e92 introduced new readahead code, adding a readpage_io_failed_hook to
disk-io.c.

The raid-repair commit had logic to disable raid-repair, if
readpage_io_failed_hook is set. Thus, the readahead commit effectively
disabled raid-repair for meta data.

This commit changes the logic to always attempt raid-repair when needed and
call the readpage_io_failed_hook in case raid-repair fails. This is much
more straight forward and should have been like that from the beginning.
Signed-off-by: Jan Schmidt <list.btrfs@jan-o-sch.net>
Reported-by: Stefan Behrens <sbehrens@giantdisaster.de>
Signed-off-by: Chris Mason <chris.mason@oracle.com>

Within nested statements, the break statement terminates only the
do, for, switch, or while statement that immediately encloses it,
So replace the break with goto.
Signed-off-by: RongQing.Li <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit a4a710c4 (pkt_sched: Change PSCHED_SHIFT from 10 to
6) it seems RED/GRED are broken.

red_calc_qavg_from_idle_time() computes a delay in us units, but this
delay is now 16 times bigger than real delay, so the final qavg result
smaller than expected.

Use standard kernel time services since there is no need to obfuscate
them.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Only use the primary address of the bond device
for master_ip. This will prevent changing the ARP source
address in Active-Backup mode whenever a secondry address
is added to the bond device.
Signed-off-by: Henrik Saavedra Persson <henrik.e.persson@ericsson.com>
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@drr.davemloft.net>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
  IB: Fix RCU lockdep splats
  IB/ipoib: Prevent hung task or softlockup processing multicast response
  IB/qib: Fix over-scheduling of QSFP work
  RDMA/cxgb4: Fix retry with MPAv1 logic for MPAv2
  RDMA/cxgb4: Fix iw_cxgb4 count_rcqes() logic
  IB/qib: Don't use schedule_work()

* 'dt-for-linus' of git://sources.calxeda.com/kernel/linux:
  of: Add Silicon Image vendor prefix
  of/irq: of_irq_init: add check for parent equal to child node

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
  regulator: twl: fix twl4030 support for smps regulators
  regulator: fix use after free bug
  regulator: aat2870: Fix the logic of checking if no id is matched in aat2870_get_regulator

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (45 commits)
  ARM: ux500: update defconfig
  ARM: u300: update defconfig
  ARM: at91: enable additional boards in existing soc defconfig files
  ARM: at91: refresh soc defconfig files for 3.2
  ARM: at91: rename defconfig files appropriately
  ARM: OMAP2+: Fix Compilation error when omap_l3_noc built as module
  ARM: OMAP2+: Remove empty io.h
  ARM: OMAP2: select ARM_AMBA if OMAP3_EMU is defined
  ARM: OMAP: smartreflex: fix IRQ handling bug
  ARM: OMAP: PM: only register TWL with voltage layer when device is present
  ARM: OMAP: hwmod: Fix the addr space, irq, dma count APIs
  arm: mx28: fix bit operation in clock setting
  ARM: imx: export imx_ioremap
  ARM: imx/mm-imx3: conditionally compile i.MX31 and i.MX35 code
  ARM: mx5: Fix checkpatch warnings in cpu-imx5.c
  MAINTAINERS: Add missing directory
  ARM: imx: drop 'ARCH_MX31' and 'ARCH_MX35'
  ARM: imx6q: move clock register map to machine_desc.map_io
  ARM: pxa168/gplugd: add the correct SSP device
  ARM: Update mach-types to fix mxs build breakage
  ...

kernel/sched.c:7354:2: warning: initialization from incompatible pointer type

Align cpu_coregroup_mask prototype interface with sched_domain_mask_f typedef
use int cpu instead of unsigned int cpu

Cc: <stable@vger.kernel.org>
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The SWP instruction is deprecated on ARMv6 and with ARMv7 it will be
UNDEFINED when CONFIG_SWP_EMULATE is selected. In this case, probing a
SWP instruction will cause an oops when the kprobes emulation code
executes an undefined instruction.

As the SWP instruction should be rare or non-existent in kernels for
ARMv6 and later, we can simply avoid these problems by not allowing
probing of these.
Reported-by: Leif Lindholm <leif.lindholm@arm.com>
Tested-by: Leif Lindholm <leif.lindholm@arm.com>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

There is a kprobes testcase for the instruction "strd r2, [r3], r4".
This has unpredictable behaviour as it uses r3 for register writeback
addressing and also stores it to memory.

On a cortex A9, this testcase would fail because the instruction writes
the updated value of r3 to memory, whereas the kprobes emulation code
writes the original value.

Fix this by changing testcase to used r5 instead of r3.
Reported-by: Leif Lindholm <leif.lindholm@arm.com>
Tested-by: Leif Lindholm <leif.lindholm@arm.com>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

After commit f2c31e32 (fix NULL dereferences in check_peer_redir()),
dst_get_neighbour() should be guarded by rcu_read_lock() /
rcu_read_unlock() section.
Reported-by: Miles Lane <miles.lane@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We need rcu_read_lock() protection before using dst_get_neighbour(), and
we must cache its value (pass it to __teql_resolve())

teql_master_xmit() is called under rcu_read_lock_bh() protection, its
not enough.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit 230dec61 (net/fec: add imx6q enet support) the FEC driver is no 
longer built by default for i.MX SoCs.

Let the FEC driver be built by default again.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Suggested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The rates bitmap for internal scan requests shoud be filled,
otherwise there will be probe requests with zero rates supported.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Johannes' patch for "cfg80211: fix regulatory NULL dereference"
broke user regulaotry hints and it did not address the fact that
last_request was left populated even if the previous regulatory
hint was stale due to the wiphy disappearing.

Fix user reguluatory hints by only bailing out if for those
regulatory hints where a request_wiphy is expected. The stale last_request
considerations are addressed through the previous fixes on last_request
where we reset the last_request to a static world regdom request upon
reset_regdomains(). In this case though we further enhance the effect
by simply restoring reguluatory settings completely.

Cc: stable@vger.kernel.org
Cc: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

There is a theoretical race that if hit will trigger
a crash. The race is between when we issue the first
regulatory hint, regulatory_hint_core(), gets processed
by the workqueue and between when the first device
gets registered to the wireless core. This is not easy
to reproduce but it was easy to do so through the
regulatory simulator I have been working on. This
is a port of the fix I implemented there [1].

[1] https://github.com/mcgrof/regsim/commit/a246ccf81f059cb662eee288aa13100f631e4cc8

Cc: stable@vger.kernel.org
Cc: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem

If we don't have a cluster, don't bother trying to allocate from it,
jumping right away to the attempt to allocate a new cluster.
Signed-off-by: Alexandre Oliva <oliva@lsd.ic.unicamp.br>
Signed-off-by: Chris Mason <chris.mason@oracle.com>

We test whether a block group has enough free space to hold the
requested block, but when we're doing clustered allocation, we can
save some cycles by testing whether it has enough room for the cluster
upfront, otherwise we end up attempting to set up a cluster and
failing.  Only in the NO_EMPTY_SIZE loop do we attempt an unclustered
allocation, and by then we'll have zeroed the cluster size, so this
patch won't stop us from using the block group as a last resort.
Signed-off-by: Alexandre Oliva <oliva@lsd.ic.unicamp.br>
Signed-off-by: Chris Mason <chris.mason@oracle.com>