If common clock framework is configured, the driver generates a warning,
which is fixed by this change:

    root@devkit3250:~# cat /dev/input/touchscreen0
    ------------[ cut here ]------------
    WARNING: CPU: 0 PID: 720 at drivers/clk/clk.c:727 clk_core_enable+0x2c/0xa4()
    Modules linked in: sc16is7xx snd_soc_uda1380
    CPU: 0 PID: 720 Comm: cat Not tainted 4.3.0-rc2+ #199
    Hardware name: LPC32XX SoC (Flattened Device Tree)
    Backtrace:
    [<>] (dump_backtrace) from [<>] (show_stack+0x18/0x1c)
    [<>] (show_stack) from [<>] (dump_stack+0x20/0x28)
    [<>] (dump_stack) from [<>] (warn_slowpath_common+0x90/0xb8)
    [<>] (warn_slowpath_common) from [<>] (warn_slowpath_null+0x24/0x2c)
    [<>] (warn_slowpath_null) from [<>] (clk_core_enable+0x2c/0xa4)
    [<>] (clk_core_enable) from [<>] (clk_enable+0x24/0x38)
    [<>] (clk_enable) from [<>] (lpc32xx_setup_tsc+0x18/0xa0)
    [<>] (lpc32xx_setup_tsc) from [<>] (lpc32xx_ts_open+0x14/0x1c)
    [<>] (lpc32xx_ts_open) from [<>] (input_open_device+0x74/0xb0)
    [<>] (input_open_device) from [<>] (evdev_open+0x110/0x16c)
    [<>] (evdev_open) from [<>] (chrdev_open+0x1b4/0x1dc)
    [<>] (chrdev_open) from [<>] (do_dentry_open+0x1dc/0x2f4)
    [<>] (do_dentry_open) from [<>] (vfs_open+0x6c/0x70)
    [<>] (vfs_open) from [<>] (path_openat+0xb4c/0xddc)
    [<>] (path_openat) from [<>] (do_filp_open+0x40/0x8c)
    [<>] (do_filp_open) from [<>] (do_sys_open+0x124/0x1c4)
    [<>] (do_sys_open) from [<>] (SyS_open+0x2c/0x30)
    [<>] (SyS_open) from [<>] (ret_fast_syscall+0x0/0x38)
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Fix the copy paste error on the electrodes_rx value set code which will
cause the electrodes_rx value be always set to the value of electrodes_y.
Reported-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Dudley Du <dudl@cypress.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

According to the touch controller spec, SPI return a 16 bit value, only 12
bits are valid, they are bit[14-3].

The value of MISO and MOSI can be configured when SPI is in idle mode.
Currently this touch driver assumes the SPI bus sets the MOSI and MISO in
low level when SPI bus is in idle mode. So the bit[15] of the value got
from SPI bus is always 0. But when SPI bus congfigures the MOSI and MISO in
high level during the SPI idle mode, the bit[15] of the value get from SPI
is always 1. If bit[15] is not masked, we may get the wrong value.

Mask the invalid bit to make sure the correct value gets returned.
Regardless of the SPI bus idle configuration.
Signed-off-by: Andrey Gelman <andrey.gelman@compulab.co.il>
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This reverts commit e51e3849: we
actually do want the device to work in extended W mode, as this is the
mode that allows us receiving multiple contact information.

Cc: stable@vger.kernel.org

The data race happens on ps2dev->cmdcnt and ps2dev->cmdbuf contents.
__ps2_command reads that data concurrently with the interrupt handler. As
the result, for example, if a response arrives just after the timeout,
__ps2_command can copy out garbage from ps2dev->cmdbuf but then see that
ps2dev->cmdcnt is 0 and return success.

Stop the interrupt handler with serio_pause_rx() before reading the
results.

The data race was found with KernelThreadSanitizer (KTSAN).
Signed-off-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Signed-off-by: Duson Lin <dusonlin@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

It uses bitrev8(), so it must ensure that lib/bitrev.o gets included in
vmlinux.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

If omap4_keypad_parse_dt() fails we returned the error code but we
missed releasing keypad_data.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

If parkbd_allocate_serio() fails to allocate memory we are releasing the
parport but we missed unregistering the device. As a result this device
with exclusive access to that parport remains registered. And no other
device will be able to use that parport even though this driver has
failed to load.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Commit b6d30968 (Input: uinput - switch to
using for_each_set_bit()) switched driver to use for_each_set_bit().
However during initial write of the uinput structure that contains min/max
data for all possible axes none of them are reflected in dev->absbit yet
and so we were skipping over all of them and were not allocating absinfo
memory which caused crash later when driver tried to sens EV_ABS events:

<1>[   15.064330] BUG: unable to handle kernel NULL pointer dereference at 0000000000000024
<1>[   15.064336] IP: [<ffffffff8163f142>] input_handle_event+0x232/0x4e0
<4>[   15.064343] PGD 0
<4>[   15.064345] Oops: 0000 [#1] SMP

Fixes: b6d30968
Cc: stable@vger.kernel.org
Reported-by: Stephen Chandler Paul <cpaul@redhat.com>
Tested-by: Stephen Chandler Paul <cpaul@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

In order to support more projects in the future, we expand the
maximum product_id value form 0xFF to 0xFFFF.

Signed-off by: Duson Lin <dusonlin@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The 0x03 is valid 3000 serial ic type too.
Signed-off-by: Duson Lin <dusonlin@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The Asus X456UA has an ELAN1000 touchpad with IAP version 0xe.  This is
unknown to elan_get_fwinfo() so driver probe fails and I am left with an
unusable touchpad.

However, the fwinfo is not required for general driver usage, it is only
needed if the user decides to upload new firmware.

Adjust the driver so that we do not abort probe when we encounter
unexpected IAP version, but rather warn user that firmware update feature
of the driver will not work.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

We should better write "Touchscreen".
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

According to Documentation/CodingStyle:

"The preferred form for passing a size of a struct is the following:

	p = kmalloc(sizeof(*p), ...);"

so do as suggested.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

We should check for negative values returned by platform_get_irq().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

imx6ul_adc_init() may fail in two cases, so we should better
propagate the errors and make sure that the callers of
this function also check and propagate the errors accordingly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

abs() function can not be used with 64 bit values, so let's switch to
abs64(). From include/linux/kernel.h:

/*
 * abs() handles unsigned and signed longs, ints, shorts and chars.
 * For all input types abs() returns a signed long.
 * abs() should not be used for 64-bit types (s64, u64, long long)
 * - use abs64() for those.
 */
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

They aren't needed and are just creating null statements so remove it.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

It's not needed and is just creating a null statement so remove it.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Section "Event Computation" had this:
    ...
    ABS_MT_TOOL_X := C_X
    ABS_MT_TOOL_X := C_Y

Replace the second ABS_MT_TOOL_X with ABS_MT_TOOL_Y.
Signed-off-by: Daniel Martin <consume.noise@gmail.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

All of the Gen3 touchpads are fixed with I2C address 0x67, so correct the
reg value description from 0x24 to 0x67.
Signed-off-by: Dudley Du <dudl@cypress.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Prepare second round of input updates for 4.3 merge window.

Since commit 81e8f2bc (Input: imx_keypad - add pm suspend and resume
support) the imx_keypad driver supports power management, so let's remove
the obsolete comment.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Freescale i.MX6UL contains a internal touchscreen controller,
this patch add a driver to support this controller.
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The Colibri Vybrid VF50 module supports 4-wire touchscreens using
FETs and ADC inputs. This driver uses the IIO consumer interface
and relies on the vf610_adc driver based on the IIO framework.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Nowadays the machines without i8042 controller is popular, and no need
to print "No controller found" message in the error log level, which
annoys at booting in quiet mode.  Let's lower it info level.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

We've got bug reports showing the old systemd-logind (at least
system-210) aborting unexpectedly, and this turned out to be because
of an invalid error code from close() call to evdev devices.  close()
is supposed to return only either EINTR or EBADFD, while the device
returned ENODEV.  logind was overreacting to it and decided to kill
itself when an unexpected error code was received.  What a tragedy.

The bad error code comes from flush fops, and actually evdev_flush()
returns ENODEV when device is disconnected or client's access to it is
revoked. But in these cases the fact that flush did not actually happen is
not an error, but rather normal behavior. For non-disconnected devices
result of flush is also not that interesting as there is no potential of
data loss and even if it fails application has no way of handling the
error. Because of that we are better off always returning success from
evdev_flush().

Also returning EINTR from flush()/close() is discouraged (as it is not
clear how application should handle this error), so let's stop taking
evdev->mutex interruptibly.

Bugzilla: http://bugzilla.suse.com/show_bug.cgi?id=939834
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The 23 inch device found in Chrome project buddy requires 9.2~10.5 seconds
to complete calibration. Let's increase calibration timeout to 12 seconds
to give the device enough time.
Signed-off-by: James Chen <james.chen@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

These platform drivers have a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luis@debethencourt.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luis@debethencourt.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luis@debethencourt.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luis@debethencourt.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The drivers have a I2C device ID table that is used to create the module
aliases and also "cyttsp" and "cyttsp4" are not supported I2C device IDs
so these module aliases are never used.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This ACPI ID present in the DSDT of the ASUS E202SA laptop.
Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Prepare first round of input updates for 4.3 merge window.

When driver is in IAP mode ic_type query may return 0xff. However
iap_version will always be valid, so let's use it to determine parameters
of the firmware that the controller is supposed to accept.
Signed-off-by: Duson Lin <dusonlin@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The driver is a platform driver and not a I2C driver so its modalias
should be exported with MODULE_DEVICE_TABLE(platform,...) instead of
MODULE_DEVICE_TABLE(i2c,...).

Also, remove the unnecessary MODULE_ALIAS("platform:max8997-haptic")
now that the correct module alias is created.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Search for "vaildpage_count" and replace with "validpage_count".
Signed-off-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

There are trackpoint devices that fail to respond to the PS2 command
PSMOUSE_CMD_GETID if immediately queried after the parent device is
deactivated. Add a small delay for the hardware to get in a sane state
before sending any PS2 commands.

One example of such a system is:
Lenovo ThinkPad X120e, model 30515QG
synaptics: Touchpad model: 1, fw: 8.0, id: 0x1e2b1, caps: 0xd001a3/0x940300/0x121c00, board id: 1811, fw id: 797391
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>