Pull remoteproc updates from Bjorn Andersson:

 - Unnecessary type casts from the 'void *' rproc->priv pointer are
   dropped throughout the subsystem.

 - A kernel-doc error is corrected in the Mediatek SCPI IPI
   implementation

 - The firmware loading onto the IMX DSP remote processors is reworked
   to avoid non-32bit memory operations. A module parameter is
   introduced to assist development of firmware without communication
   abilities in place. Error paths in imx_dsp_rproc_mbox_alloc() is
   cleaned up

 - The cluster configuration handling in the TI K3 R5 driver is
   corrected and support for the single-R5 core found in the TI AM62x
   SoC family is introduced

 - The TI PRU driver device- to virtual-address translation is updated
   to avoid compiler warning about the unsigned device-address always
   being larger than 0

 - The ST remoteproc driver is transitioned to use of_property_present()

 - Issues with kicks arriving after the STM32 remote processor has been
   shut down are mitigated by checking the processor's state before
   handling them.

 - Support for mailbox channels for communication with the remote
   processors are added to the Xilinx R5 remoteproc driver. The naming
   of carveouts are corrected and their parsing is reworked. For this a
   couple of fixes targeting the mailbox subsystem are picked up here as
   well.

 - Reference counting of of_nodes are corrected in the ST, STM32, RCAR
   and IMX remoteproc drivers

* tag 'rproc-v6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux: (24 commits)
  remoteproc: st: Use of_property_present() for testing DT property presence
  dt-bindings: remoteproc: Drop unneeded quotes
  remoteproc: imx_dsp_rproc: Fix kernel test robot sparse warning
  remoteproc: imx_dsp_rproc: Improve exception handling in imx_dsp_rproc_mbox_alloc()
  remoteproc: pru: Remove always true check positive unsigned value
  dt-bindings: remoteproc: stm32-rproc: Typo fix
  remoteproc: stm32_rproc: Add mutex protection for workqueue
  remoteproc: Remove unnecessary (void*) conversions
  remoteproc: imx_dsp_rproc: Call of_node_put() on iteration error
  remoteproc: imx_rproc: Call of_node_put() on iteration error
  remoteproc: rcar_rproc: Call of_node_put() on iteration error
  remoteproc: st: Call of_node_put() on iteration error
  remoteproc: stm32: Call of_node_put() on iteration error
  remoteproc: k3-r5: Use separate compatible string for TI AM62x SoC family
  dt-bindings: remoteproc: ti: Add new compatible for AM62 SoC family
  remoteproc: k3-r5: Simplify cluster mode setting usage
  remoteproc/mtk_scpi_ipi: Fix one kernel-doc comment
  remoteproc: xilinx: Add mailbox channels for rpmsg
  drivers: remoteproc: xilinx: Fix carveout names
  mailbox: zynqmp: Fix typo in IPI documentation
  ...

Pull rpmsg updates from Bjorn Andersson:
 "The remove functions of the Qualcomm SMD and GLINK RPM platform
  drivers are transitioned to the new void returning prototype. Likewise
  is qcom_smd_unregister_edge() transitioned to void, as it
  unconditionally returned 0.

  An assumption about the ordering of the intent request acknowledgement
  and advertisement of a new intent in the GLINK implementation is
  corrected. Faulty error handling is corrected is improved in the TX
  path, and duplicated code, in the same path, is cleaned up"

* tag 'rpmsg-v6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux:
  rpmsg: glink: Consolidate TX_DATA and TX_DATA_CONT
  rpmsg: glink: Propagate TX failures in intentless mode as well
  rpmsg: glink: Wait for intent, not just request ack
  rpmsg: glink: Transition intent request signaling to wait queue
  rpmsg: qcom_smd: Convert to platform remove callback returning void
  rpmsg: qcom_glink_rpm: Convert to platform remove callback returning void
  rpmsg: qcom_smd: Make qcom_smd_unregister_edge() return void

Pull MMC updates from Ulf Hansson:
 "MMC core:
   - Allow an invalid regulator in mmc_regulator_set_ocr()
   - Log about empty non-removable slots
   - Add helpers to enable/disable the vqmmc regulator

  MMC host:
   - mtk-sd: Add support for the mt8365 variant
   - renesas_sdhi: Remove support for R-Car H3 ES1.* variants
   - sdhci_am654: Add power management support
   - sdhci-cadence: Add support for eMMC hardware reset
   - sdhci-cadence: Add support for AMD Pensando Elba variant
   - sdhci-msm: Add support for the IPQ5018 variant
   - sdhci-msm: Add support for the QCM2290 variant
   - sdhci-of-arasan: Skip setting clock delay for 400KHz
   - sdhci-of-arasan: Add support for the Xilinx Versal Net variant
   - sdhci-of-arasan: Remove Intel Thunder Bay SOC support
   - sdhci-of-arasan: Add support to request the "gate" clock
   - sdhci-of-dwcmshc: Properly determine max clock on Rockchip
   - sdhci-of-esdhc: Fix quirk to ignore command inhibit for data
   - sdhci-pci-o2micro: Fix SDR50 mode timing issue

  MEMSTICK:
   - r592: Fix use-after-free bug in r592_remove due to race condition"

* tag 'mmc-v6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (40 commits)
  dt-bindings: mmc: sdhci-msm: Document the IPQ5018 compatible
  mmc: vub300: remove unreachable code
  mmc: sdhci-cadence: Support mmc hardware reset
  mmc: sdhci-cadence: Add AMD Pensando Elba SoC support
  mmc: sdhci-cadence: Support device specific init during probe
  mmc: sdhci-cadence: Enable device specific override of writel()
  dt-bindings: mmc: cdns: Add AMD Pensando Elba SoC
  mmc: core: Remove unused macro mmc_req_rel_wr
  mmc: sdhci-of-arasan: Skip setting clock delay for 400KHz
  mmc: sdhci-of-arasan: Add support for eMMC5.1 on Xilinx Versal Net platform
  dt-bindings: mmc: arasan,sdci: Add Xilinx Versal Net compatible
  mmc: sdhci_am654: Add support for PM suspend/resume
  mmc: core: remove unnecessary (void*) conversions
  dt-bindings: mmc: fsl-imx-esdhc: ref sdhci-common.yaml
  mmc: sdhci-of-esdhc: fix quirk to ignore command inhibit for data
  mmc: core: Log about empty non-removable slots
  dt-bindings: mmc: fujitsu: Add Socionext Synquacer
  mmc: sdricoh_cs: remove unused sdricoh_readw function
  dt-bindings: mmc: Remove bindings for Intel Thunder Bay SoC"
  mmc: sdhci-of-arasan: Remove Intel Thunder Bay SOC support
  ...

Pull mtd updates from Miquel Raynal:
 "Core MTD changes:
   - dt-bindings: Drop unneeded quotes
   - mtdblock: Tolerate corrected bit-flips
   - Use of_property_read_bool() for boolean properties
   - Avoid magic values
   - Avoid printing error messages on probe deferrals
   - Prepare mtd_otp_nvmem_add() to handle -EPROBE_DEFER
   - Fix error path for nvmem provider
   - Fix nvmem error reporting
   - Provide unique name for nvmem device

  MTD device changes:
   - lpddr_cmds: Remove unused words variable
   - bcm63xxpart: Remove MODULE_LICENSE in non-modules

  SPI NOR core changes:
   - Introduce Read While Write support for flashes featuring several
     banks
   - Set the 4-Byte Address Mode method based on SFDP data
   - Allow post_sfdp hook to return errors
   - Parse SCCR MC table and introduce support for multi-chip devices

  SPI NOR manufacturer drivers changes:
   - macronix: Add support for mx25uw51245g with RWW
   - spansion:
      - Determine current address mode at runtime as it can be changed
        in a non-volatile way and differ from factory defaults or from
        what SFDP advertises.
      - Enable JFFS2 write buffer mode for few ECC'd NOR flashes:
        S25FS256T, s25hx and s28hx
      - Add support for s25hl02gt and s25hs02gt

  Raw NAND core changes:
   - Convert to platform remove callback returning void
   - Fix spelling mistake waifunc() -> waitfunc()

  Raw NAND controller driver changes:
   - imx: Remove unused is_imx51_nfc and imx53_nfc functions
   - omap2: Drop obsolete dependency on COMPILE_TEST
   - orion: Use devm_platform_ioremap_resource()
   - qcom:
      - Use of_property_present() for testing DT property presence
      - Use devm_platform_get_and_ioremap_resource()
   - stm32_fmc2: Depends on ARCH_STM32 instead of MACH_STM32MP157
   - tmio: Remove reference to config MTD_NAND_TMIO in the parsers

  Raw NAND manufacturer driver changes:
   - hynix: Fix up bit 0 of sdr_timing_mode

  SPI-NAND changes:
   - Add support for ESMT F50x1G41LB"

* tag 'mtd/for-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (55 commits)
  mtd: nand: Convert to platform remove callback returning void
  mtd: onenand: omap2: Drop obsolete dependency on COMPILE_TEST
  mtd: spi-nor: spansion: Add support for s25hl02gt and s25hs02gt
  mtd: spi-nor: spansion: Add a new ->ready() hook for multi-chip device
  mtd: spi-nor: spansion: Rework cypress_nor_quad_enable_volatile() for multi-chip device support
  mtd: spi-nor: spansion: Rework cypress_nor_get_page_size() for multi-chip device support
  mtd: spi-nor: sfdp: Add support for SCCR map for multi-chip device
  mtd: spi-nor: Extract volatile register offset from SCCR map
  mtd: spi-nor: Allow post_sfdp hook to return errors
  mtd: spi-nor: spansion: Rename method to cypress_nor_get_page_size
  mtd: spi-nor: spansion: Enable JFFS2 write buffer for S25FS256T
  mtd: spi-nor: spansion: Enable JFFS2 write buffer for Infineon s25hx SEMPER flash
  mtd: spi-nor: spansion: Enable JFFS2 write buffer for Infineon s28hx SEMPER flash
  mtd: spi-nor: spansion: Determine current address mode
  mtd: spi-nor: core: Introduce spi_nor_set_4byte_addr_mode()
  mtd: spi-nor: core: Update flash's current address mode when changing address mode
  mtd: spi-nor: Stop exporting spi_nor_restore()
  mtd: spi-nor: Set the 4-Byte Address Mode method based on SFDP data
  mtd: spi-nor: core: Make spi_nor_set_4byte_addr_mode_brwr public
  mtd: spi-nor: core: Update name and description of spi_nor_set_4byte_addr_mode
  ...

Pull gpio updates from Bartosz Golaszewski:
 "We have some new drivers, significant refactoring of existing intel
  platforms, lots of improvements all around, mass conversion to using
  immutable irqchips by drivers that had not been converted individually
  yet and some changes in the core library code.

  Summary:

  New drivers:
   - add a driver for the Loongson GPIO controller
   - add a driver for the fxl6408 I2C GPIO expander
   - add a GPIO module containing code common for Intel Elkhart Lake and
     Merrifield platforms
   - add a driver for the Intel Elkhart Lake platform reusing the code
     from the intel tangier library

  GPIOLIB core:
   - GPIO ACPI improvements
   - simplify gpiochip_add_data_with_keys() fwnode handling
   - cleanup header inclusions (remove unneeded ones, order the rest
     alphabetically)
   - remove duplicate code (reuse krealloc() instead of open-coding it,
     drop a duplicated check in gpiod_find_and_request())
   - reshuffle the code to remove unnecessary forward declarations
   - coding style cleanups and improvements
   - add a helper for accessing device fwnodes
   - small updates in docs

  Driver improvements:
   - convert all remaining GPIO irqchip drivers to using immutable
     irqchips
   - drop unnecessary of_match_ptr() macro expansions
   - shrink the code in gpio-merrifield significantly by reusing the
     code from gpio-tangier + minor tweaks to the driver code
   - remove MODULE_LICENSE() from drivers that can only be built-in
   - add device-tree support to gpio-loongson1
   - use new regmap features in gpio-104-dio-48e and gpio-pcie-idio-24
   - minor tweaks and fixes to gpio-xra1403, gpio-sim, gpio-tegra194,
     gpio-omap, gpio-aspeed, gpio-raspberrypi-exp
   - shrink code in gpio-ich and gpio-pxa
   - Kconfig tweak for gpio-pmic-eic-sprd"

* tag 'gpio-updates-for-v6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (99 commits)
  gpio: gpiolib: Simplify gpiochip_add_data_with_key() fwnode
  gpiolib: Add gpiochip_set_data() helper
  gpiolib: Move gpiochip_get_data() higher in the code
  gpiolib: Check array_info for NULL only once in gpiod_get_array()
  gpiolib: Replace open coded krealloc()
  gpiolib: acpi: Add a ignore wakeup quirk for Clevo NL5xNU
  gpiolib: acpi: Move ACPI device NULL check to acpi_get_driver_gpio_data()
  gpiolib: acpi: use the fwnode in acpi_gpiochip_find()
  gpio: mm-lantiq: Fix typo in the newly added header filename
  sh: mach-x3proto: Add missing #include <linux/gpio/driver.h>
  powerpc/40x: Add missing select OF_GPIO_MM_GPIOCHIP
  gpio: xlp: Convert to immutable irq_chip
  gpio: xilinx: Convert to immutable irq_chip
  gpio: xgs-iproc: Convert to immutable irq_chip
  gpio: visconti: Convert to immutable irq_chip
  gpio: tqmx86: Convert to immutable irq_chip
  gpio: thunderx: Convert to immutable irq_chip
  gpio: stmpe: Convert to immutable irq_chip
  gpio: siox: Convert to immutable irq_chip
  gpio: rda: Convert to immutable irq_chip
  ...

Pull regulator updates from Mark Brown:
 "A fairly quiet release, there were some cleanup and a couple of new
  devices but the biggest change was converting most of the drivers to
  use asynchronous probe. This allows us to ramp up multiple regulators
  in parallel during boot which can have a noticable impact on modern
  systems.

  Summary:

   - Update of drivers to PROBE_PREFER_ASYNCHRONOUS to mitigate issues
     with ramp times slowing down boots.

   - Convert to void remove callbacks.

   - Support for voltage monitoring on DA9063

   - Support for Qualcomm PMC8180 and PMM8654au, Richtek RT4803 and
     RT5739, Rockchip RK860x"

* tag 'regulator-v6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (46 commits)
  regulator: dt-bindings: qcom,rpmh: Combine PM6150L and PM8150L if-then
  regulator: core: Make regulator_lock_two() logic easier to follow
  regulator: dt-bindings: qcom,rpmh: Correct PM8550 family supplies
  regulator: stm32-pwr: fix of_iomap leak
  dt-bindings: mfd: dlg,da9063: document voltage monitoring
  regulator: da9063: implement setter for voltage monitoring
  regulator: da9063: add voltage monitoring registers
  regulator: fan53555: Add support for RK860X
  regulator: fan53555: Use dev_err_probe
  regulator: fan53555: Improve vsel_mask computation
  regulator: fan53555: Make use of the bit macros
  regulator: fan53555: Remove unused *_SLEW_SHIFT definitions
  regulator: dt-bindings: fcs,fan53555: Add support for RK860X
  regulator: qcom_smd: Add MP5496 S1 regulator
  regulator: qcom_smd: Add s1 sub-node to mp5496 regulator
  regulator: qcom,rpmh: add compatible for pmm8654au RPMH
  regulator: qcom-rpmh: add support for pmm8654au regulators
  regulator: core: Avoid lockdep reports when resolving supplies
  regulator: core: Consistently set mutex_owner when using ww_mutex_lock_slow()
  regulator: dt-bindings: qcom,rpmh: Add compatible for PMC8180
  ...

Pull regmap updates from Mark Brown:
 "This is a much bigger change for regmap than is normal, the main
  things being the addition of some KUnit coverage and a maple tree
  based register cache which longer term is likely to replace the rbtree
  cache except possibly for very small register maps.

  While it's complete overkill for most applications the code for maple
  trees is there and there are some larger, sparser devices where the
  data structure is a better fit.

  The maple tree support is still a work in progress but already useful,
  there's some conversions of drivers ready to go after the merge
  window.

  Summary:

   - Support for shifting register addresses up as well as down, there's
     a use cases with memory mapped MDIO.

   - Refactoring of the type configuration in regmap-irq to allow access
     to driver data in the handler, needed by some GPIO devices.

   - Some initial KUnit coverage, the bulk of the driver facing API is
     covered but there's holes and things like the data marshalling for
     bytestream buses are just not covered in the slightest.

   - Removal of the compressed cache type, it had zero users and was
     getting in the way of KUnit.

   - Addition of a maple tree based register cache, there's more work to
     do but it's already useful for some devices with a flatter data
     structure than rbtree and getting to use all the optimisation work
     Liam is doing"

* tag 'regmap-v6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
  regmap: allow upshifting register addresses before performing operations
  regmap: Pass irq_drv_data as a parameter for set_type_config()
  regmap: Use mas_walk() instead of mas_find()
  regmap: Fix double unlock in the maple cache
  regmap: Add maple tree based register cache
  regmap: Factor out single value register syncing
  regmap: Add some basic kunit tests
  regmap: Add RAM backed register map
  regmap: Removed compressed cache support
  regmap: Support paging for buses with reg_read()/reg_write()
  regmap: Clarify error for unknown cache types
  regmap: Handle sparse caches in the default sync
  regmap: add a helper to translate the register address
  regmap: cache: Silence checkpatch warning
  regmap: cache: Return error in cache sync operations for REGCACHE_NONE
  regmap-irq: Place kernel doc of struct regmap_irq_chip in order
  regmap-irq: Add no_status support
  regmap: sdw: Remove 8-bit value size restriction
  regmap: sdw: Update misleading comment

Merge tag 'platform-drivers-x86-v6.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86

Pull x86 platform driver updates from Hans de Goede:

 -  AMD PMC and PMF drivers:
    - Numerous bugfixes

 -  Intel Speed Select Technology (ISST):
    - TPMI (Topology Aware Register and PM Capsule Interface) support
      for ISST support on upcoming processor models
    - Various other improvements / new hw support
    - tools/intel-speed-select: TPMI support + other improvements

 -  Intel In Field Scan (IFS):
    - Add Array Bist test support

 -  New drivers:
    - intel_bytcrc_pwrsrc Crystal Cove PMIC pwrsrc / reset-reason driver
    - lenovo-ymc Yoga Mode Control driver for reporting SW_TABLET_MODE
    - msi-ec Driver for MSI laptop EC features like battery charging limits

 -  apple-gmux:
    - Support for new MMIO based models (T2 Macs)
    - Honor acpi_backlight= auto-detect-code + kernel cmdline option
      to switch between gmux and apple_bl backlight drivers and remove
      own custom handling for this

 -  x86-android-tablets: Refactor / cleanup + new hw support

 -  Miscellaneous other cleanups / fixes

* tag 'platform-drivers-x86-v6.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86: (178 commits)
  platform/x86: x86-android-tablets: Add accelerometer support for Yoga Tablet 2 1050/830 series
  platform/x86: x86-android-tablets: Add "yogabook-touch-kbd-digitizer-switch" pdev for Lenovo Yoga Book
  platform/x86: x86-android-tablets: Add Wacom digitizer info for Lenovo Yoga Book
  platform/x86: x86-android-tablets: Update Yoga Book HiDeep touchscreen comment
  platform/x86: thinkpad_acpi: Fix Embedded Controller access on X380 Yoga
  platform/x86/intel/sdsi: Change mailbox timeout
  platform/x86/intel/pmt: Ignore uninitialized entries
  platform/x86: amd: pmc: provide user message where s0ix is not supported
  platform/x86/amd: pmc: Fix memory leak in amd_pmc_stb_debugfs_open_v2()
  mlxbf-bootctl: Add sysfs file for BlueField boot fifo
  platform/x86: amd: pmc: Remove __maybe_unused from amd_pmc_suspend_handler()
  platform/x86/intel/pmc/mtl: Put GNA/IPU/VPU devices in D3
  platform/x86/amd: pmc: Move out of BIOS SMN pair for STB init
  platform/x86/amd: pmc: Utilize SMN index 0 for driver probe
  platform/x86/amd: pmc: Move idlemask check into `amd_pmc_idlemask_read`
  platform/x86/amd: pmc: Don't dump data after resume from s0i3 on picasso
  platform/x86/amd: pmc: Hide SMU version and program attributes for Picasso
  platform/x86/amd: pmc: Don't try to read SMU version on Picasso
  platform/x86/amd/pmf: Move out of BIOS SMN pair for driver probe
  platform/x86: intel-uncore-freq: Add client processors
  ...

Merge tag 'tag-chrome-platform-for-v6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux

Pull chrome platform updates from Tzung-Bi Shih:
 "Improvements:

   - Replace fake flexible arrays with flexible-array member

  Misc:

   - Minor cleanups and fixes"

* tag 'tag-chrome-platform-for-v6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux:
  platform/chrome: wilco_ec: remove return value check of debugfs_create_dir()
  platform/chrome: cros_ec_debugfs: fix kernel-doc warning
  platform/chrome: cros_ec: Separate logic for getting panic info
  platform/chrome: cros_typec_switch: Add missing fwnode_handle_put()
  platform/chrome: cros_ec: remove unneeded label and if-condition
  platform/chrome: Replace fake flexible arrays with flexible-array member

Pull media updates from Mauro Carvalho Chehab:

 - Removal of some old unused sensor drivers: ad9389b, m5mols, mt9m032,
   mt9t001, noon010pc30, s5k6aa, sr030pc30 and vs6624

 - New i.MX8 image sensor interface driver

 - Some new RC keymaps

 - lots of cleanups at atomisp driver to make it support standard
   features present on other webcam drivers

 - the cx18 and saa7146 now uses VB2

 - lots of cleanups and driver improvements

* tag 'media/v6.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (460 commits)
  media: ov5670: Fix probe on ACPI
  media: nxp: imx8-isi: Remove 300ms sleep after enabling channel
  media: nxp: imx8-isi: Replace udelay() with fsleep()
  media: nxp: imx8-isi: Drop partial support for i.MX8QM and i.MX8QXP
  media: nxp: Add i.MX8 ISI driver
  media: dt-bindings: media: Add i.MX8 ISI DT bindings
  media: atomisp: gmin_platform: Add Lenovo Ideapad Miix 310 gmin_vars
  media: atomisp: gmin_platform: Make DMI quirks take precedence over the _DSM table
  media: atomisp: Remove struct atomisp_sub_device index field
  media: atomisp: Drop support for streaming from 2 sensors at once
  media: atomisp: Remove atomisp_try_fmt() call from atomisp_set_fmt()
  media: atomisp: Remove unused ATOM_ISP_MAX_WIDTH_TMP and ATOM_ISP_MAX_HEIGHT_TMP
  media: atomisp: Remove snr_mbus_fmt local var from atomisp_try_fmt()
  media: atomisp: Remove custom V4L2_CID_FMT_AUTO control
  media: atomisp: Remove continuous mode related code from atomisp_set_fmt()
  media: atomisp: Remove duplicate atomisp_[start|stop]_streaming() prototypes
  media: atomisp: gc0310: Switch over to ACPI powermanagement
  media: atomisp: gc0310: Use devm_kzalloc() for data struct
  media: atomisp: gc0310: Add runtime-pm support
  media: atomisp: gc0310: Delay power-on till streaming is started
  ...

Pull drm updates from Dave Airlie:
 "There is a new Qualcomm accel driver for their QAIC, dma-fence got a
  deadline feature added, lots of refactoring around fbdev emulation,
  and the usual pre-release hw enablements from AMD and Intel and fixes
  everywhere.

  New drivers:
   - add QAIC acceleration driver

  dma-buf:
   - constify kobj_type structs
   - Reject prime DMA-Buf attachment if get_sg_table is missing.

  fbdev:
   - cmdline parser fixes
   - implement fbdev emulation for GEM DMA drivers
   - always use shadow buffer in fbdev emulation helpers

  dma-fence:
   - add deadline hint to fences
   - signal private stub fence

  core:
   - improve DisplayID 2.0 and EDID parsing
   - add gem eviction function + callback
   - prep to convert shmem helper to GEM resv lock
   - move suballocator from radeon/amdgpu to core for Xe
   - HPD polling fixes
   - Documentation improvements
   - Add atomic enable_plane callback
   - use tgid instead of pid for client tracking
   - DP: Add SDP Error Detection Configuration Register
   - Add prime import/export to vram-helper
   - use pci aperture helpers in more drivers

  panel:
   - Radxa 8/10HD support
   - Samsung AMD495QA01 support
   - Elida KD50T048A
   - Sony TD4353
   - Novatek NT36523
   - STARRY 2081101QFH032011-53G
   - B133UAN01.0
   - AUO NE135FBM-N41

  i915:
   - More MTL enabling
   - fix s/r problems with MEI/PXP
   - Implement fb_dirty for PSR,FBC,DRRS fixes
   - Fix eDP+DSI dual panel systems
   - Fix issue #6333: "list_add corruption" and full system lockup from
     performance monitoring
   - Don't use stolen memory or BAR for ring buffers on LLC platforms
   - Make sure DSM size has correct 1MiB granularity on Gen12+
   - Whitelist COMMON_SLICE_CHICKEN3 for UMD access on Gen12+
   - Add engine TLB invalidation for Meteorlake
   - Fix GSC races on driver load/unload on Meteorlake+
   - Make kobj_type structures constant
   - Move fd_install after last use of fence
   - wm/vblank refactoring
   - display code refactoring
   - Create GSC submission targeting HDCP and PXP usages on MTL+
   - Enable HDCP2.x via GSC CS
   - Fix context runtime accounting on sysfs fdinfo for heavy workloads
   - Use i915 instead of dev_priv insied the file_priv structure
   - Replace fake flex-array with flexible-array member

  amdgpu:
   - Make kobj structures const
   - Generalize dmabuf import to work with KFD
   - Add capped/uncapped workload handling for supported APUs
   - Expose additional memory stats via fdinfo
   - Register vga_switcheroo for apple-gmux
   - Initial NBIO7.9, GC 9.4.3, GFXHUB 1.2, MMHUB 1.8 support
   - Initial DC FAM infrastructure
   - Link DC backlight to connector device rather than PCI device
   - Add sysfs nodes for secondary VCN clocks

  amdkfd:
   - Make kobj structures const
   - Support for exporting buffers via dmabuf
   - Multi-VMA page migration fixes
   - initial GC 9.4.3 support

  radeon:
   - iMac fix
   - convert to client based fbdev emulation

  habanalabs:
   - Add opcodes to the CS ioctl to allow user to stall/resume specific
     engines inside Gaudi2.
   - INFO ioctl the amount of device memory that the driver and f/w
     reserve for themselves.
   - INFO ioctl a bit-mask of the available rotator engines
   - INFO ioctl the register's address of the f/w that should be used to
     trigger interrupts
   - INFO ioctl two new opcodes to fetch information on h/w and f/w
     events
   - Enable graceful reset mechanism for compute-reset.
   - Align to the latest firmware specs.
   - Enforce the release order of the compute device and dma-buf.

  msm:
   - UBWC decoder programming rework
   - SM8550, SM8450 bindings update
   - uapi C++ fix
   - a3xx and a4xx devfreq support
   - GPU and GEM updates to avoid allocations which could trigger
     reclaim (shrinker) in fence signaling path
   - dma-fence deadline hint support and wait-boost
   - a640/650 speed bin support

  cirrus:
   - convert to regular atomic helpers
   - add damage clipping

  mediatek:
   - 10-bit overlay support
   - mt8195 support
   - Only trigger DRM HPD events if bridge is attached
   - Change the aux retries times when receiving AUX_DEFER

  rockchip:
   - add 4K support

  vc4:
   - use drm_gem_objects

  virtio:
   - allow KMS support to be disabled
   - add damage clipping

  vmwgfx:
   - buffer object lifetime fixes

  exynos:
   - move MIPI DSI driver to drm bridge for iMX sharing
   - use kernel fbdev emulation

  panfrost:
   - add support for mali MT81xx devices
   - add speed binning support

  lima:
   - add usage stats

  tegra:
   - fbdev client conversion

  vkms:
   - Add primary plane positioning support"

* tag 'drm-next-2023-04-24' of git://anongit.freedesktop.org/drm/drm: (1495 commits)
  drm/i915/dp_mst: Fix active port PLL selection for secondary MST streams
  drm/exynos: Implement fbdev emulation as in-kernel client
  drm/exynos: Initialize fbdev DRM client
  drm/exynos: Remove fb_helper from struct exynos_drm_private
  drm/exynos: Remove struct exynos_drm_fbdev
  drm/exynos: Remove exynos_gem from struct exynos_drm_fbdev
  drm/i915: Fix memory leaks in i915 selftests
  drm/i915: Make intel_get_crtc_new_encoder() less oopsy
  drm/i915/gt: Avoid out-of-bounds access when loading HuC
  drm/amdgpu: add some basic elements for multiple XCD case
  drm/amdgpu: move vmhub out of amdgpu_ring_funcs (v4)
  Revert "drm/amdgpu: enable ras for mp0 v13_0_10 on SRIOV"
  drm/amdgpu: add common ip block for GC 9.4.3
  drm/amd/display: Add logging when DP link training Clock recovery is Successful
  drm/amdgpu: add common early init support for GC 9.4.3
  drm/amdgpu: switch to v9_4_3 gfx_funcs callbacks for GC 9.4.3
  drm/amd/display: Add logging when setting DP sink power state fails
  drm/amdkfd: Add gfx_target_version for GC 9.4.3
  drm/amdkfd: Enable HW_UPDATE_RPTR on GC 9.4.3
  drm/amdgpu: reserve the old gc_11_0_*_mes.bin
  ...

Pull slab updates from Vlastimil Babka:
 "The main change is naturally the SLOB removal. Since its deprecation
  in 6.2 I've seen no complaints so hopefully SLUB_(TINY) works well for
  everyone and we can proceed.

  Besides the code cleanup, the main immediate benefit will be allowing
  kfree() family of function to work on kmem_cache_alloc() objects,
  which was incompatible with SLOB. This includes kfree_rcu() which had
  no kmem_cache_free_rcu() counterpart yet and now it shouldn't be
  necessary anymore.

  Besides that, there are several small code and comment improvements
  from Thomas, Thorsten and Vernon"

* tag 'slab-for-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/vbabka/slab:
  mm/slab: document kfree() as allowed for kmem_cache_alloc() objects
  mm/slob: remove slob.c
  mm/slab: remove CONFIG_SLOB code from slab common code
  mm, pagemap: remove SLOB and SLQB from comments and documentation
  mm, page_flags: remove PG_slob_free
  mm/slob: remove CONFIG_SLOB
  mm/slub: fix help comment of SLUB_DEBUG
  mm: slub: make kobj_type structure constant
  slab: Adjust comment after refactoring of gfp.h

Merge tag 'livepatching-for-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/livepatching/livepatching

Pull livepatching updates from Petr Mladek:

 - Code and documentation cleanup

* tag 'livepatching-for-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/livepatching/livepatching:
  livepatch: Make kobj_type structures constant
  livepatch: fix ELF typos

Pull printk updates from Petr Mladek:

 - Code cleanup and dead code removal

* tag 'printk-for-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux:
  printk: Remove obsoleted check for non-existent "user" object
  lib/vsprintf: Use isodigit() for the octal number check
  Remove orphaned CONFIG_PRINTK_SAFE_LOG_BUF_SHIFT

Pull arm64 updates from Will Deacon:
 "ACPI:

   - Improve error reporting when failing to manage SDEI on AGDI device
     removal

  Assembly routines:

   - Improve register constraints so that the compiler can make use of
     the zero register instead of moving an immediate #0 into a GPR

   - Allow the compiler to allocate the registers used for CAS
     instructions

  CPU features and system registers:

   - Cleanups to the way in which CPU features are identified from the
     ID register fields

   - Extend system register definition generation to handle Enum types
     when defining shared register fields

   - Generate definitions for new _EL2 registers and add new fields for
     ID_AA64PFR1_EL1

   - Allow SVE to be disabled separately from SME on the kernel
     command-line

  Tracing:

   - Support for "direct calls" in ftrace, which enables BPF tracing for
     arm64

  Kdump:

   - Don't bother unmapping the crashkernel from the linear mapping,
     which then allows us to use huge (block) mappings and reduce TLB
     pressure when a crashkernel is loaded.

  Memory management:

   - Try again to remove data cache invalidation from the coherent DMA
     allocation path

   - Simplify the fixmap code by mapping at page granularity

   - Allow the kfence pool to be allocated early, preventing the rest of
     the linear mapping from being forced to page granularity

  Perf and PMU:

   - Move CPU PMU code out to drivers/perf/ where it can be reused by
     the 32-bit ARM architecture when running on ARMv8 CPUs

   - Fix race between CPU PMU probing and pKVM host de-privilege

   - Add support for Apple M2 CPU PMU

   - Adjust the generic PERF_COUNT_HW_BRANCH_INSTRUCTIONS event
     dynamically, depending on what the CPU actually supports

   - Minor fixes and cleanups to system PMU drivers

  Stack tracing:

   - Use the XPACLRI instruction to strip PAC from pointers, rather than
     rolling our own function in C

   - Remove redundant PAC removal for toolchains that handle this in
     their builtins

   - Make backtracing more resilient in the face of instrumentation

  Miscellaneous:

   - Fix single-step with KGDB

   - Remove harmless warning when 'nokaslr' is passed on the kernel
     command-line

   - Minor fixes and cleanups across the board"

* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (72 commits)
  KVM: arm64: Ensure CPU PMU probes before pKVM host de-privilege
  arm64: kexec: include reboot.h
  arm64: delete dead code in this_cpu_set_vectors()
  arm64/cpufeature: Use helper macro to specify ID register for capabilites
  drivers/perf: hisi: add NULL check for name
  drivers/perf: hisi: Remove redundant initialized of pmu->name
  arm64/cpufeature: Consistently use symbolic constants for min_field_value
  arm64/cpufeature: Pull out helper for CPUID register definitions
  arm64/sysreg: Convert HFGITR_EL2 to automatic generation
  ACPI: AGDI: Improve error reporting for problems during .remove()
  arm64: kernel: Fix kernel warning when nokaslr is passed to commandline
  perf/arm-cmn: Fix port detection for CMN-700
  arm64: kgdb: Set PSTATE.SS to 1 to re-enable single-step
  arm64: move PAC masks to <asm/pointer_auth.h>
  arm64: use XPACLRI to strip PAC
  arm64: avoid redundant PAC stripping in __builtin_return_address()
  arm64/sme: Fix some comments of ARM SME
  arm64/signal: Alloc tpidr2 sigframe after checking system_supports_tpidr2()
  arm64/signal: Use system_supports_tpidr2() to check TPIDR2
  arm64/idreg: Don't disable SME when disabling SVE
  ...

Pull asm-generic updates from Arnd Bergmann:
 "These are various cleanups, fixing a number of uapi header files to no
  longer reference CONFIG_* symbols, and one patch that introduces the
  new CONFIG_HAS_IOPORT symbol for architectures that provide working
  inb()/outb() macros, as a preparation for adding driver dependencies
  on those in the following release"

* tag 'asm-generic-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
  Kconfig: introduce HAS_IOPORT option and select it as necessary
  scripts: Update the CONFIG_* ignore list in headers_install.sh
  pktcdvd: Remove CONFIG_CDROM_PKTCDVD_WCACHE from uapi header
  Move bp_type_idx to include/linux/hw_breakpoint.h
  Move ep_take_care_of_epollwakeup() to fs/eventpoll.c
  Move COMPAT_ATM_ADDPARTY to net/atm/svc.c

Pull ARM SoC devicetree updates from Arnd Bergmann:
 "The devicetree changes overall are again dominated by the Qualcomm
  Snapdragon platform that weighs in at over 300 changesets, but there
  are many updates across other platforms as well, notably Mediatek,
  NXP, Rockchips, Renesas, TI, Samsung and ST Microelectronics. These
  all add new features for existing machines, as well as new machines
  and SoCs.

  The newly added SoCs are:

   - Allwinner T113-s, an Cortex-A7 based variant of the RISC-V based D1
     chip.

   - StarFive JH7110, a RISC-V SoC based on the Sifive U74 core like its
     JH7100 predecessor, but with additional CPU cores and a GPU.

   - Apple M2 as used in current Macbook Air/Pro and Mac Mini gets
     added, with comparable support as its M1 predecessor.

   - Unisoc UMS512 (Tiger T610) is a midrange smartphone SoC

   - Qualcomm IPQ5332 and IPQ9574 are Wi-Fi 7 networking SoCs, based on
     the Cortex-A53 and Cortex-A73 cores, respectively.

   - Qualcomm sa8775p is an automotive SoC derived from the Snapdragon
     family.

  Including the initial board support for the added SoC platforms, there
  are 52 new machines. The largest group are 19 boards industrial
  embedded boards based on the NXP i.MX6 (32-bit) and i.MX8 (64-bit)
  families.

  Others include:

   - Two boards based on the Allwinner f1c200s ultra-low-cost chip

   - Three 'Banana Pi' variants based on the Amlogic g12b (A311D, S922X)
     SoC.

   - The Gl.Inet mv1000 router based on Marvell Armada 3720

   - A Wifi/LTE Dongle based on Qualcomm msm8916

   - Two robotics boards based on Qualcomm QRB chips

   - Three Snapdragon based phones made by Xiaomi

   - Five developments boards based on various Rockchip SoCs, including
     the rk3588s-khadas-edge2 and a few NanoPi models

   - The AM625 Beagleplay industrial SBC

  Another 14 machines get removed: both boards for the obsolete 'oxnas'
  platform, three boards for the Renesas r8a77950 SoC that were only for
  pre-production chips, and various chromebook models based on the
  Qualcomm Sc7180 'trogdor' design that were never part of products"

* tag 'soc-dt-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (836 commits)
  arm64: dts: rockchip: Add support for volume keys to rk3399-pinephone-pro
  arm64: dts: rockchip: Add vdd_cpu_big regulators to rk3588-rock-5b
  arm64: dts: rockchip: Use generic name for es8316 on Pinebook Pro and Rock 5B
  arm64: dts: rockchip: Drop RTC clock-frequency on rk3588-rock-5b
  arm64: dts: apple: t8112: Add PWM controller
  arm64: dts: apple: t600x: Add PWM controller
  arm64: dts: apple: t8103: Add PWM controller
  arm64: dts: rockchip: Add pinctrl gpio-ranges for rk356x
  ARM: dts: nomadik: Replace deprecated spi-gpio properties
  ARM: dts: aspeed-g6: Add UDMA node
  ARM: dts: aspeed: greatlakes: add mctp device
  ARM: dts: aspeed: greatlakes: Add gpio names
  ARM: dts: aspeed: p10bmc: Change power supply info
  arm64: dts: mediatek: mt6795-xperia-m5: Add Bosch BMM050 Magnetometer
  arm64: dts: mediatek: mt6795-xperia-m5: Add Bosch BMA255 Accelerometer
  arm64: dts: mediatek: mt6795: Add tertiary PWM node
  arm64: dts: rockchip: add panel to Anbernic RG353 series
  dt-bindings: arm: Add Data Modul i.MX8M Plus eDM SBC
  dt-bindings: arm: fsl: Add chargebyte Tarragon
  dt-bindings: vendor-prefixes: add chargebyte
  ...

Pull ARM SoC defconfig updates from Arnd Bergmann:
 "Most of the changes just enable additional device drivers that were
  added or that are often used on major platforms.

  The virtconfig added last time now disables additional drivers to
  shrink kernels for virtual machines.

  The obsolete oxnas_v6_defconfig file is removed in turn"

* tag 'soc-defconfig-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (33 commits)
  ARM: config: Update Vexpress defconfig
  arm64: defconfig: enable building the nvmem-reboot-mode module
  arm64: defconfig: Enable TI ADC driver
  arm64: defconfig: Enable TI TSCADC driver
  arm64: defconfig: Enable security accelerator driver for TI K3 SoCs
  arm64: defconfig: Enable crypto test module
  ARM: multi_v7_defconfig: Add OPTEE support
  ARM: configs: Update U8500 defconfig
  ARM: imx_v4_v5_defconfig: Build CONFIG_IMX_SDMA as module
  arm64: defconfig: Enable IPQ9574 SoC base configs
  ARM: imx_v6_v7_defconfig: Enable Tarragon peripheral drivers
  arm64: defconfig: Enable ARM CoreSight PMU driver
  arm64: defconfig: remove duplicate TYPEC_UCSI & QCOM_PMIC_GLINK
  ARM: configs: remove oxnas_v6_defconfig
  arm64: defconfig: Enable audio drivers for AM62-SK
  arm64: defconfig: Enable drivers for BeaglePlay
  ARM: imx_v6_v7_defconfig: Select CONFIG_DRM_I2C_NXP_TDA998X
  arm64: defconfig: Enable Virtio RNG driver as built in
  arm64: defconfig: Enable CAN PHY transceiver driver
  arm64: defconfig: add PMIC GLINK modules
  ...

Pull ARM SoC driver updates from Arnd Bergmann:
 "The most notable updates this time are for Qualcomm Snapdragon
  platforms. The Inline-Crypto-Engine gets a new DT binding and driver,
  and a number of drivers now support additional Snapdragon variants, in
  particular the rsc, scm, geni, bwm, glink and socinfo, while the llcc
  (edac) and rpm drivers get notable functionality updates.

  Updates on other platforms include:

   - Various updates to the Mediatek mutex and mmsys drivers, including
     support for the Helio X10 SoC

   - Support for unidirectional mailbox channels in Arm SCMI firmware

   - Support for per cpu asynchronous notification in OP-TEE firmware

   - Minor updates for memory controller drivers.

   - Minor updates for Renesas, TI, Amlogic, Apple, Broadcom, Tegra,
     Allwinner, Versatile Express, Canaan, Microchip, Mediatek and i.MX
     SoC drivers, mainly updating the use of MODULE_LICENSE() macros and
     obsolete DT driver interfaces"

* tag 'soc-drivers-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (165 commits)
  soc: ti: smartreflex: Simplify getting the opam_sr pointer
  bus: vexpress-config: Add explicit of_platform.h include
  soc: mediatek: Kconfig: Add MTK_CMDQ dependency to MTK_MMSYS
  memory: mtk-smi: mt8365: Add SMI Support
  dt-bindings: memory-controllers: mediatek,smi-larb: add mt8365
  dt-bindings: memory-controllers: mediatek,smi-common: add mt8365
  memory: tegra: read values from correct device
  dt-bindings: crypto: Add Qualcomm Inline Crypto Engine
  soc: qcom: Make the Qualcomm UFS/SDCC ICE a dedicated driver
  dt-bindings: firmware: document Qualcomm QCM2290 SCM
  soc: qcom: rpmh-rsc: Support RSC v3 minor versions
  soc: qcom: smd-rpm: Use GFP_ATOMIC in write path
  soc/tegra: fuse: Remove nvmem root only access
  soc/tegra: cbb: tegra194: Use of_address_count() helper
  soc/tegra: cbb: Remove MODULE_LICENSE in non-modules
  ARM: tegra: Remove MODULE_LICENSE in non-modules
  soc/tegra: flowctrl: Use devm_platform_get_and_ioremap_resource()
  soc: tegra: cbb: Drop empty platform remove function
  firmware: arm_scmi: Add support for unidirectional mailbox channels
  dt-bindings: firmware: arm,scmi: Support mailboxes unidirectional channels
  ...

Pull ARM SoC updates from Arnd Bergmann:
 "The Oxford Semiconductor OX810/OX820 'Oxnas' platform gets retired
  after the ARM11MPcore processor keeps causing problems in certain
  corner cases. OX820 was the only remaining SoC with this core after
  CNS3xxx got retired, and its driver support was never completely
  merged upstream. The Arm 'Realview' reference platform still supports
  ARM11MPCore in principle, but this was never a product, and the CPU
  support will get cleaned up later on.

  Another series updates the mv78xx0 platform, which has been similarly
  neglected for a while, but should work properly again now.

  The other changes are minor cleanups across platforms, mostly
  converting code to more modern interfaces for DT nodes and removing
  some more code as a follow-up to the large-scale platform removal in
  linux-6.3"

* tag 'soc-arm-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (28 commits)
  ARM: mv78xx0: fix entries for gpios, buttons and usb ports
  ARM: mv78xx0: add code to enable XOR and CRYPTO engines on mv78xx0
  ARM: mv78xx0: set the correct driver for the i2c RTC
  ARM: mv78xx0: adjust init logic for ts-wxl to reflect single core dev
  soc: fsl: Use of_property_present() for testing DT property presence
  ARM: pxa: Use of_property_read_bool() for boolean properties
  firmware: turris-mox-rwtm: make kobj_type structure constant
  ARM: oxnas: remove OXNAS support
  ARM: sh-mobile: Use of_cpu_node_to_id() to read CPU node 'reg'
  ARM: OMAP2+: hwmod: Use kzalloc for allocating only one element
  ARM: OMAP2+: Remove the unneeded result variable
  ARM: OMAP2+: fix repeated words in comments
  ARM: OMAP2+: remove obsolete config OMAP3_SDRC_AC_TIMING
  ARM: OMAP2+: Use of_address_to_resource()
  ARM: OMAP2+: Use of_property_read_bool() for boolean properties
  ARM: omap1: remove redundant variables err
  ARM: omap1: Kconfig: Fix indentation
  ARM: bcm: Use of_address_to_resource()
  ARM: mstar: remove unused config MACH_MERCURY
  ARM: spear: remove obsolete config MACH_SPEAR600
  ...

Pull x86 APIC updates from Thomas Gleixner:

 - Fix the incorrect handling of atomic offset updates in
   reserve_eilvt_offset()

   The check for the return value of atomic_cmpxchg() is not compared
   against the old value, it is compared against the new value, which
   makes it two round on success.

   Convert it to atomic_try_cmpxchg() which does the right thing.

 - Handle IO/APIC less systems correctly

   When IO/APIC is not advertised by ACPI then the computation of the
   lower bound for dynamically allocated interrupts like MSI goes wrong.

   This lower bound is used to exclude the IO/APIC legacy GSI space as
   that must stay reserved for the legacy interrupts.

   In case that the system, e.g. VM, does not advertise an IO/APIC the
   lower bound stays at 0.

   0 is an invalid interrupt number except for the legacy timer
   interrupt on x86. The return value is unchecked in the core code, so
   it ends up to allocate interrupt number 0 which is subsequently
   considered to be invalid by the caller, e.g. the MSI allocation code.

   A similar problem was already cured for device tree based systems
   years ago, but that missed - or did not envision - the zero IO/APIC
   case.

   Consolidate the zero check and return the provided "from" argument to
   the core code call site, which is guaranteed to be greater than 0.

 - Simplify the X2APIC cluster CPU mask logic for CPU hotplug

   Per cluster CPU masks are required for X2APIC in cluster mode to
   determine the correct cluster for a target CPU when calculating the
   destination for IPIs

   These masks are established when CPUs are borught up. The first CPU
   in a cluster must allocate a new cluster CPU mask. As this happens
   during the early startup of a CPU, where memory allocations cannot be
   done, the mask has to be allocated by the control CPU.

   The current implementation allocates a clustermask just in case and
   if the to be brought up CPU is the first in a cluster the CPU takes
   over this allocation from a global pointer.

   This works nicely in the fully serialized CPU bringup scenario which
   is used today, but would fail completely for parallel bringup of
   CPUs.

   The cluster association of a CPU can be computed from the APIC ID
   which is enumerated by ACPI/MADT.

   So the cluster CPU masks can be preallocated and associated upfront
   and the upcoming CPUs just need to set their corresponding bit.

   Aside of preparing for parallel bringup this is a valuable
   simplification on its own.

 - Remove global variables which control the early startup of secondary
   CPUs on 64-bit

   The only information which is needed by a starting CPU is the Linux
   CPU number. The CPU number allows it to retrieve the rest of the
   required data from already existing per CPU storage.

   So instead of initial_stack, early_gdt_desciptor and initial_gs
   provide a new variable smpboot_control which contains the Linux CPU
   number for now. The starting CPU can retrieve and compute all
   required information for startup from there.

   Aside of being a cleanup, this is also preparing for parallel CPU
   bringup, where starting CPUs will look up their Linux CPU number via
   the APIC ID, when smpboot_control has the corresponding control bit
   set.

 - Make cc_vendor globally accesible

   Subsequent parallel bringup changes require access to cc_vendor
   because confidental computing platforms need special treatment in the
   early startup phase vs. CPUID and APCI ID readouts.

   The change makes cc_vendor global and provides stub accessors in case
   that CONFIG_ARCH_HAS_CC_PLATFORM is not set.

   This was merged from the x86/cc branch in anticipation of further
   parallel bringup commits which require access to cc_vendor. Due to
   late discoveries of fundamental issue with those patches these
   commits never happened.

   The merge commit is unfortunately in the middle of the APIC commits
   so unraveling it would have required a rebase or revert. As the
   parallel bringup seems to be well on its way for 6.5 this would be
   just pointless churn. As the commit does not contain any functional
   change it's not a risk to keep it.

* tag 'x86-apic-2023-04-24' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/ioapic: Don't return 0 from arch_dynirq_lower_bound()
  x86/apic: Fix atomic update of offset in reserve_eilvt_offset()
  x86/coco: Export cc_vendor
  x86/smpboot: Reference count on smpboot_setup_warm_reset_vector()
  x86/smpboot: Remove initial_gs
  x86/smpboot: Remove early_gdt_descr on 64-bit
  x86/smpboot: Remove initial_stack on 64-bit
  x86/apic/x2apic: Allow CPU cluster_mask to be populated in parallel

Pull timers and timekeeping updates from Thomas Gleixner:

 - Improve the VDSO build time checks to cover all dynamic relocations

   VDSO does not allow dynamic relocations, but the build time check is
   incomplete and fragile.

   It's based on architectures specifying the relocation types to search
   for and does not handle R_*_NONE relocation entries correctly.
   R_*_NONE relocations are injected by some GNU ld variants if they
   fail to determine the exact .rel[a]/dyn_size to cover trailing zeros.
   R_*_NONE relocations must be ignored by dynamic loaders, so they
   should be ignored in the build time check too.

   Remove the architecture specific relocation types to check for and
   validate strictly that no other relocations than R_*_NONE end up in
   the VSDO .so file.

 - Prefer signal delivery to the current thread for
   CLOCK_PROCESS_CPUTIME_ID based posix-timers

   Such timers prefer to deliver the signal to the main thread of a
   process even if the context in which the timer expires is the current
   task. This has the downside that it might wake up an idle thread.

   As there is no requirement or guarantee that the signal has to be
   delivered to the main thread, avoid this by preferring the current
   task if it is part of the thread group which shares sighand.

   This not only avoids waking idle threads, it also distributes the
   signal delivery in case of multiple timers firing in the context of
   different threads close to each other better.

 - Align the tick period properly (again)

   For a long time the tick was starting at CLOCK_MONOTONIC zero, which
   allowed users space applications to either align with the tick or to
   place a periodic computation so that it does not interfere with the
   tick. The alignement of the tick period was more by chance than by
   intention as the tick is set up before a high resolution clocksource
   is installed, i.e. timekeeping is still tick based and the tick
   period advances from there.

   The early enablement of sched_clock() broke this alignement as the
   time accumulated by sched_clock() is taken into account when
   timekeeping is initialized. So the base value now(CLOCK_MONOTONIC) is
   not longer a multiple of tick periods, which breaks applications
   which relied on that behaviour.

   Cure this by aligning the tick starting point to the next multiple of
   tick periods, i.e 1000ms/CONFIG_HZ.

 - A set of NOHZ fixes and enhancements:

     * Cure the concurrent writer race for idle and IO sleeptime
       statistics

       The statitic values which are exposed via /proc/stat are updated
       from the CPU local idle exit and remotely by cpufreq, but that
       happens without any form of serialization. As a consequence
       sleeptimes can be accounted twice or worse.

       Prevent this by restricting the accumulation writeback to the CPU
       local idle exit and let the remote access compute the accumulated
       value.

     * Protect idle/iowait sleep time with a sequence count

       Reading idle/iowait sleep time, e.g. from /proc/stat, can race
       with idle exit updates. As a consequence the readout may result
       in random and potentially going backwards values.

       Protect this by a sequence count, which fixes the idle time
       statistics issue, but cannot fix the iowait time problem because
       iowait time accounting races with remote wake ups decrementing
       the remote runqueues nr_iowait counter. The latter is impossible
       to fix, so the only way to deal with that is to document it
       properly and to remove the assertion in the selftest which
       triggers occasionally due to that.

     * Restructure struct tick_sched for better cache layout

     * Some small cleanups and a better cache layout for struct
       tick_sched

 - Implement the missing timer_wait_running() callback for POSIX CPU
   timers

   For unknown reason the introduction of the timer_wait_running()
   callback missed to fixup posix CPU timers, which went unnoticed for
   almost four years.

   While initially only targeted to prevent livelocks between a timer
   deletion and the timer expiry function on PREEMPT_RT enabled kernels,
   it turned out that fixing this for mainline is not as trivial as just
   implementing a stub similar to the hrtimer/timer callbacks.

   The reason is that for CONFIG_POSIX_CPU_TIMERS_TASK_WORK enabled
   systems there is a livelock issue independent of RT.

   CONFIG_POSIX_CPU_TIMERS_TASK_WORK=y moves the expiry of POSIX CPU
   timers out from hard interrupt context to task work, which is handled
   before returning to user space or to a VM. The expiry mechanism moves
   the expired timers to a stack local list head with sighand lock held.
   Once sighand is dropped the task can be preempted and a task which
   wants to delete a timer will spin-wait until the expiry task is
   scheduled back in. In the worst case this will end up in a livelock
   when the preempting task and the expiry task are pinned on the same
   CPU.

   The timer wheel has a timer_wait_running() mechanism for RT, which
   uses a per CPU timer-base expiry lock which is held by the expiry
   code and the task waiting for the timer function to complete blocks
   on that lock.

   This does not work in the same way for posix CPU timers as there is
   no timer base and expiry for process wide timers can run on any task
   belonging to that process, but the concept of waiting on an expiry
   lock can be used too in a slightly different way.

   Add a per task mutex to struct posix_cputimers_work, let the expiry
   task hold it accross the expiry function and let the deleting task
   which waits for the expiry to complete block on the mutex.

   In the non-contended case this results in an extra
   mutex_lock()/unlock() pair on both sides.

   This avoids spin-waiting on a task which is scheduled out, prevents
   the livelock and cures the problem for RT and !RT systems

* tag 'timers-core-2023-04-24' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  posix-cpu-timers: Implement the missing timer_wait_running callback
  selftests/proc: Assert clock_gettime(CLOCK_BOOTTIME) VS /proc/uptime monotonicity
  selftests/proc: Remove idle time monotonicity assertions
  MAINTAINERS: Remove stale email address
  timers/nohz: Remove middle-function __tick_nohz_idle_stop_tick()
  timers/nohz: Add a comment about broken iowait counter update race
  timers/nohz: Protect idle/iowait sleep time under seqcount
  timers/nohz: Only ever update sleeptime from idle exit
  timers/nohz: Restructure and reshuffle struct tick_sched
  tick/common: Align tick period with the HZ tick.
  selftests/timers/posix_timers: Test delivery of signals across threads
  posix-timers: Prefer delivery of signals to the current thread
  vdso: Improve cmd_vdso_check to check all dynamic relocations

Pull interrupt updates from Thomas Gleixner:
 "Core:

   - Add tracepoints for tasklet callbacks which makes it possible to
     analyze individual tasklet functions instead of guess working from
     the overall duration of tasklet processing

   - Ensure that secondary interrupt threads have their affinity
     adjusted correctly

  Drivers:

   - A large rework of the RISC-V IPI management to prepare for a new
     RISC-V interrupt architecture

   - Small fixes and enhancements all over the place

   - Removal of support for various obsolete hardware platforms and the
     related code"

* tag 'irq-core-2023-04-24' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (21 commits)
  irqchip/st: Remove stih415/stih416 and stid127 platforms support
  irqchip/gic-v3: Add Rockchip 3588001 erratum workaround
  genirq: Update affinity of secondary threads
  softirq: Add trace points for tasklet entry/exit
  irqchip/loongson-pch-pic: Fix pch_pic_acpi_init calling
  irqchip/loongson-pch-pic: Fix registration of syscore_ops
  irqchip/loongson-eiointc: Fix registration of syscore_ops
  irqchip/loongson-eiointc: Fix incorrect use of acpi_get_vec_parent
  irqchip/loongson-eiointc: Fix returned value on parsing MADT
  irqchip/riscv-intc: Add empty irq_eoi() for chained irq handlers
  RISC-V: Use IPIs for remote icache flush when possible
  RISC-V: Use IPIs for remote TLB flush when possible
  RISC-V: Allow marking IPIs as suitable for remote FENCEs
  RISC-V: Treat IPIs as normal Linux IRQs
  irqchip/riscv-intc: Allow drivers to directly discover INTC hwnode
  RISC-V: Clear SIP bit only when using SBI IPI operations
  irqchip/irq-sifive-plic: Add syscore callbacks for hibernation
  irqchip: Use of_property_read_bool() for boolean properties
  irqchip/bcm-6345-l1: Request memory region
  irqchip/gicv3: Workaround for NVIDIA erratum T241-FABRIC-4
  ...

Pull core entry/ptrace update from Thomas Gleixner:
 "Provide a ptrace set/get interface for syscall user dispatch. The main
  purpose is to enable checkpoint/restore (CRIU) to handle processes
  which utilize syscall user dispatch correctly"

* tag 'core-entry-2023-04-24' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  selftest, ptrace: Add selftest for syscall user dispatch config api
  ptrace: Provide set/get interface for syscall user dispatch
  syscall_user_dispatch: Untag selector address before access_ok()
  syscall_user_dispatch: Split up set_syscall_user_dispatch()

Pull core debugobjects update from Thomas Gleixner:
 "A single update to debugobjects:

  Prevent a race vs statically initialized objects. Such objects are
  usually not initialized via an init() function. They are special cased
  and detected on first use under the assumption that they are already
  correctly initialized via the static initializer.

  This works correctly unless there are two concurrent debug object
  operations on such an object.

  The first one detects that the object is not yet tracked and tries to
  establish a tracking object after dropping the debug objects hash
  bucket lock. The concurrent operation does the same. The one which
  wins the race ends up modifying the state of the object which makes
  the other one fail resulting in a bogus debug objects warning.

  Prevent this by making the detection of a static object and the
  allocation of a tracking object atomic under the hash bucket lock. So
  the first one to acquire the hash bucket lock will succeed and the
  second one will observe the correct tracking state.

  This race existed forever but was only exposed when the timer wheel
  code added a debug_object_assert_init() call outside of the timer base
  locked region. This replaced the previous warning about
  timer::function being NULL which had to be removed when the
  timer_shutdown() mechanics were added"

* tag 'core-debugobjects-2023-04-24' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  debugobject: Prevent init race with static objects

Pull x86 SEV updates from Borislav Petkov:

 - Add the necessary glue so that the kernel can run as a confidential
   SEV-SNP vTOM guest on Hyper-V. A vTOM guest basically splits the
   address space in two parts: encrypted and unencrypted. The use case
   being running unmodified guests on the Hyper-V confidential computing
   hypervisor

 - Double-buffer messages between the guest and the hardware PSP device
   so that no partial buffers are copied back'n'forth and thus potential
   message integrity and leak attacks are possible

 - Name the return value the sev-guest driver returns when the hw PSP
   device hasn't been called, explicitly

 - Cleanups

* tag 'x86_sev_for_v6.4_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/hyperv: Change vTOM handling to use standard coco mechanisms
  init: Call mem_encrypt_init() after Hyper-V hypercall init is done
  x86/mm: Handle decryption/re-encryption of bss_decrypted consistently
  Drivers: hv: Explicitly request decrypted in vmap_pfn() calls
  x86/hyperv: Reorder code to facilitate future work
  x86/ioremap: Add hypervisor callback for private MMIO mapping in coco VM
  x86/sev: Change snp_guest_issue_request()'s fw_err argument
  virt/coco/sev-guest: Double-buffer messages
  crypto: ccp: Get rid of __sev_platform_init_locked()'s local function pointer
  crypto: ccp - Name -1 return value as SEV_RET_NO_FW_CALL

Pull x86 paravirt updates from Borislav Petkov:

 - Convert a couple of paravirt callbacks to asm to prevent
   '-fzero-call-used-regs' builds from zeroing live registers because
   paravirt hides the CALLs from the compiler so latter doesn't know
   there's a CALL in the first place

 - Merge two paravirt callbacks into one, as their functionality is
   identical

* tag 'x86_paravirt_for_v6.4_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/paravirt: Convert simple paravirt functions to asm
  x86/paravirt: Merge activate_mm() and dup_mmap() callbacks

Pull misc x86 updates from Borislav Petkov:

 - Add a x86 hw vulnerabilities section to MAINTAINERS so that the folks
   involved in it can get CCed on patches

 - Add some more CPUID leafs to the kcpuid tool and extend its
   functionality to be more useful when grepping for CPUID bits

* tag 'x86_misc_for_v6.4_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  MAINTAINERS: Add x86 hardware vulnerabilities section
  tools/x86/kcpuid: Dump the CPUID function in detailed view
  tools/x86/kcpuid: Update AMD leaf Fn80000001
  tools/x86/kcpuid: Fix avx512bw and avx512lvl fields in Fn00000007

Pull x86 cpu model updates from Borislav Petkov:

 - Add Emerald Rapids to the list of Intel models supporting PPIN

 - Finally use a CPUID bit for split lock detection instead of
   enumerating every model

 - Make sure automatic IBRS is set on AMD, even though the AP bringup
   code does that now by replicating the MSR which contains the switch

* tag 'x86_cpu_for_v6.4_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/cpu: Add Xeon Emerald Rapids to list of CPUs that support PPIN
  x86/split_lock: Enumerate architectural split lock disable bit
  x86/CPU/AMD: Make sure EFER[AIBRSE] is set

Pull x86 ACPI update from Borislav Petkov:

 - Improve code generation in ACPI's global lock's acquisition function

* tag 'x86_acpi_for_v6.4_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/ACPI/boot: Improve __acpi_acquire_global_lock

Pull RAS updates from Borislav Petkov:

 - Just cleanups and fixes this time around: make threshold_ktype const,
   an objtool fix and use proper size for a bitmap

* tag 'ras_core_for_v6.4_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/MCE/AMD: Use an u64 for bank_map
  x86/mce: Always inline old MCA stubs
  x86/MCE/AMD: Make kobj_type structure constant

Pull EDAC updates from Borislav Petkov:

 - skx_edac: Fix overflow when decoding 32G DIMM ranks

 - i10nm_edac: Add Sierra Forest support

 - amd64_edac: Split driver code between legacy and SMCA systems. The
   final goal is adding support for more hw, like GPUs

 - The usual minor cleanups and fixes

* tag 'edac_updates_for_v6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras: (25 commits)
  EDAC/i10nm: Add Intel Sierra Forest server support
  EDAC/amd64: Fix indentation in umc_determine_edac_cap()
  EDAC/altera: Remove MODULE_LICENSE in non-module
  EDAC: Sanitize MODULE_AUTHOR strings
  EDAC/amd81[13]1: Remove trailing newline from MODULE_AUTHOR
  EDAC/amd64: Add get_err_info() to pvt->ops
  EDAC/amd64: Split dump_misc_regs() into dct/umc functions
  EDAC/amd64: Split init_csrows() into dct/umc functions
  EDAC/amd64: Split determine_edac_cap() into dct/umc functions
  EDAC/amd64: Rename f17h_determine_edac_ctl_cap()
  EDAC/amd64: Split setup_mci_misc_attrs() into dct/umc functions
  EDAC/amd64: Split ecc_enabled() into dct/umc functions
  EDAC/amd64: Split read_mc_regs() into dct/umc functions
  EDAC/amd64: Split determine_memory_type() into dct/umc functions
  EDAC/amd64: Split read_base_mask() into dct/umc functions
  EDAC/amd64: Split prep_chip_selects() into dct/umc functions
  EDAC/amd64: Rework hw_info_{get,put}
  EDAC/amd64: Merge struct amd64_family_type into struct amd64_pvt
  EDAC/amd64: Do not discover ECC symbol size for Family 17h and later
  EDAC/amd64: Drop dbam_to_cs() for Family 17h and later
  ...

Pull m68k updates from Geert Uytterhoeven:

 - defconfig updates

 - miscellaneous fixes and improvements

* tag 'm68k-for-v6.4-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
  m68k: kexec: Include <linux/reboot.h>
  m68k: defconfig: Update defconfigs for v6.3-rc1
  m68k: Remove obsolete config NO_KERNEL_MSG
  nubus: Drop noop match function

devm_clk_get() will return either an error or NULL, which the driver
handles, continuing to use the clock of reading the value of the
clock-frequency property.

However, the value of ov5670->xvclk is left as-is and the other clock
framework functions aren't capable of handling error values.

Use devm_clk_get_optional() to obtain NULL instead of -ENOENT.

Fixes: 8004c91e ("media: i2c: ov5670: Use common clock framework")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

Pull trivial nios2 cleanup from Al Viro.

* tag 'pull-nios2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  nios2: _TIF_ALLWORK_MASK is unused

Pull misc vfs pile from Al Viro.

Random minor cleanups.

* tag 'pull-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  fs: Fix description of vfs_tmpfile()
  sysv: switch to put_and_unmap_page()
  fs/sysv: Don't round down address for kunmap_flush_on_unmap()

Pull legacy dio cleanup from Al Viro.

* tag 'pull-old-dio' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  __blockdev_direct_IO(): get rid of submit_io callback

Pull vfs write_one_page removal from Al Viro:
 "write_one_page series"

* tag 'pull-write-one-page' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  mm,jfs: move write_one_page/folio_write_one to jfs
  ocfs2: don't use write_one_page in ocfs2_duplicate_clusters_by_page
  ufs: don't flush page immediately for DIRSYNC directories

Pull vfs fget updates from Al Viro:
 "fget() to fdget() conversions"

* tag 'pull-fd' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  fuse_dev_ioctl(): switch to fdget()
  cgroup_get_from_fd(): switch to fdget_raw()
  bpf: switch to fdget_raw()
  build_mount_idmapped(): switch to fdget()
  kill the last remaining user of proc_ns_fget()
  SVM-SEV: convert the rest of fget() uses to fdget() in there
  convert sgx_set_attribute() to fdget()/fdput()
  convert setns(2) to fdget()/fdput()

Pull erofs updates from Gao Xiang:
 "In this cycle, sub-page block support for uncompressed files is
  available. It's mainly used to enable original signing ('golden')
  4k-block images on arm64 with 16/64k pages. In addition, end users
  could also use this feature to build a manifest to directly refer to
  golden tar data.

  Besides, long xattr name prefix support is also introduced in this
  cycle to avoid too many xattrs with the same prefix (e.g. overlayfs
  xattrs). It's useful for erofs + overlayfs combination (like Composefs
  model): the image size is reduced by ~14% and runtime performance is
  also slightly improved.

  Others are random fixes and cleanups as usual.

  Summary:

   - Add sub-page block size support for uncompressed files

   - Support flattened block device for multi-blob images to be attached
     into virtual machines (including cloud servers) and bare metals

   - Support long xattr name prefixes to optimize images with common
     xattr namespaces (e.g. files with overlayfs xattrs) use cases

   - Various minor cleanups & fixes"

* tag 'erofs-for-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs:
  erofs: cleanup i_format-related stuffs
  erofs: sunset erofs_dbg()
  erofs: fix potential overflow calculating xattr_isize
  erofs: get rid of z_erofs_fill_inode()
  erofs: enable long extended attribute name prefixes
  erofs: handle long xattr name prefixes properly
  erofs: add helpers to load long xattr name prefixes
  erofs: introduce on-disk format for long xattr name prefixes
  erofs: move packed inode out of the compression part
  erofs: keep meta inode into erofs_buf
  erofs: initialize packed inode after root inode is assigned
  erofs: stop parsing non-compact HEAD index if clusterofs is invalid
  erofs: don't warn ztailpacking feature anymore
  erofs: simplify erofs_xattr_generic_get()
  erofs: rename init_inode_xattrs with erofs_ prefix
  erofs: move several xattr helpers into xattr.c
  erofs: tidy up EROFS on-disk naming
  erofs: support flattened block device for multi-blob images
  erofs: set block size to the on-disk block size
  erofs: avoid hardcoded blocksize for subpage block support