This is mostly just the stuff I missed last round.  Various cleanup
patches + fixes, improvements to display colour management, and some
code to avoid loading when power cables aren't properly attached.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Ben Skeggs <skeggsb@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CACAvsv7hqj9_VHq+YiGL8Z8XsU2vPbqbNPC=LeN1Rb0XxMQypQ@mail.gmail.com

Some, mostly Fermi, vbioses appear to have zero max voltage. That causes Nouveau to not parse voltage entries, thus users not being able to set higher clocks.

When changing this value Nvidia driver still appeared to ignore it, and I wasn't able to find out why, thus the code is ignoring the value if it is zero.

CC: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Mark Menzynski <mmenzyns@redhat.com>
Reviewed-by: Karol Herbst <kherbst@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

This is something that got noticed a while ago back when I was fixing a
large number of runtime PM related issues in nouveau, but never got
fixed:

https://patchwork.freedesktop.org/series/46815/#rev7

It's not safe to iterate the entire list of CRTCs in
nv50_disp_atomic_commit(), as we could be doing a non-blocking modeset
on one CRTC in parallel with one or more other CRTCs. Likewise, this
means it's also not safe to do so in order to track runtime PM state.
While this code is certainly wrong, so far the only issues I've seen
this cause in the wild is the occasional PM ref unbalance after an
atomic check failure + module reloading (since the PCI device will
outlive nouveau in such scenarios).

So, do this far more elegantly: grab a runtime PM ref across the modeset
and commit tail, then grab/put references for each CRTC enable/disable.
This also ends up being much simpler then the previous broken solution
we had.

Finally, since we've removed all it's users: get rid of
nouveau_drm->have_disp_power_ref.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Originally when trying to fix the issue of runtime PM references with
non-blocking CRTCs on nv50, I ended up stumbling on this code when
trying to remove nouveau_drm->have_disp_power_ref, and attempted to fix
it to remove the dependency on have_disp_power_ref. However, Ilia Mirkin
pointed out that this code is actually completely useless, as pre-nv50
never had runtime PM support in the first place! Go figure.

So, since it's useless just get rid of it. Note that since the only
thing nouveau_crtc_set_config() was doing was grabbing a runtime PM ref,
calling drm_crtc_helper_set_config() then dropping the ref; we can just
remove the function entirely and just call drm_crtc_helper_set_config()
directly.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Added GPIO is "Power Alert". It's uncertain if this
GPIO is set on GPU initialization or only if a change is detected by the
GPU at runtime.

This GPIO can be found on Tesla and sometimes on Fermi GPUs.

Untested, wrote according to documentation.
Signed-off-by: Mark Menzynski <mmenzyns@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Added GPIO is "Thermal and External Power Detect". It's uncertain if this
GPIO is set on GPU initialization or only if a change is detected by the
GPU at runtime.

This GPIO can be found in Rankine and Curie and rarely on Tesla GPUs
VBIOS.

Untested, wrote according to documentation.
Signed-off-by: Mark Menzynski <mmenzyns@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Currently, nouveau doesn't check if GPU is missing power. This
patch makes nouveau fail when this happens on latest GPUs.

It checks GPIO function 121 (External Power Emergency), which
should detect power problems on GPU initialization.

This can be disabled with nouveau.config=NvPowerChecks=1

Tested on TU104, GP106 and GF100.

v3:
*  Add config override for disabling power checks
Signed-off-by: Mark Menzynski <mmenzyns@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

One gpio was in wrong place, moved it for better readability.
Signed-off-by: Mark Menzynski <mmenzyns@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

There's already a condition in place which attempts to detect this, but
since we've begun to require a PMU subdev even on boards where we don't
load a custom FW, it's become inaccurate.

This will prevent unnecessarily running a periodic fan update thread on
GP100 and newer, where we don't yet override the default PMU FW.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Saves some time during driver load, as described by the relevant section[1]
of the DCB 4.x specification.

[1] https://nvidia.github.io/open-gpu-doc/DCB/DCB-4.x-Specification.html#_i2c_device_tableSigned-off-by: Ben Skeggs <bskeggs@redhat.com>

Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Has a nice side-effect that we only update HW for this when it changes now,
rather than every time we do a page flip.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Defaulting to the fixed layout enforced in HW by EVO, and that we
currently use by default on NVD.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

zpos normalisation uses plane id to determine ordering for duplicate zpos
values, and we likely want to keep primary plane on the bottom here.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

We have some of this open-coded already, use the helper to prevent problems
when adding (for example) support for the alpha property.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

This is apparently the assumed default behaviour when blend properties
are absent.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

For GF119:GV100, we can enable DEGAMMA/CTM/GAMMA. For earlier GPUs, as
there is no CTM, having both degamma and gamma is a bit pointless. Later
GPUs currently lack an implementation.
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

This adds support on GF119:GV100 (exclusive) for CTM (aka CSC).
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>

The overlay logic can only do colorkey-based selection, not
alpha-blending.
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Pascal was particularly incorrect, as the register changed to be more in the
same format as the MMU fault buffers are.

Shouldn't have impacted much more than confusing MMU fault log messages.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Would like to be able to reuse gf100_fifo_intr_fault() for (some of) the
later chipsets too, as it's identical.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Signal that the reset sequence has completed.

This opcode signals that the software reset sequence has completed.
Ordinarily, no actual operations are performed by the opcode.
However it allows for possible software work arounds by devinit
engines in software agents other than the VBIOS, such as the resman,
FCODE, and EFI driver.
Signed-off-by: Rhys Kidd <rhyskidd@gmail.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Signal that the reset sequence has begun.

This opcode signals that the software reset sequence has begun.
Ordinarily, no actual operations are performed by the opcode.
However it allows for possible software work arounds by devinit
engines in software agents other than the VBIOS, such as the resman,
FCODE, and EFI driver.
Signed-off-by: Rhys Kidd <rhyskidd@gmail.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Absence of a TMDS Info Table is common on Optimus setups where the NVIDIA
gpu is not connected directly to any outputs.

Reporting an error in this scenario is too harsh. Accordingly, change the
error message to an info message.

By default the error message also causes a boot flicker for these sytems.
Signed-off-by: Rhys Kidd <rhyskidd@gmail.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

We now have per-device driver_features, so let's use that
to disable atomic only for pre-nv50.

Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Lyude Paul <lyude@redhat.com>
Cc: nouveau@lists.freedesktop.org
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Older hardware seems to want 0..1024 values, while new hardware takes
0..1 values. We set the gain to 1024 for the earlier display classes.
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Under some circumstances, it could be left enabled when it shouldn't be.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

On Turing, an input LUT is required to transform inputs in fixed-point
formats to FP16 for the internal display pipe.  We provide an identity
mapping whenever a window is enabled for this reason.

HW has error checks to ensure when the input is already FP16, that the
input LUT is also disabled.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Required for upcoming FP16 scanout support.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

remove duplicate inclusion of nvif/device.h

Issue identified by includecheck
Signed-off-by: Hariprasad Kelam <hariprasad.kelam@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

remove duplicate inclusion of subdev/bios.h

Issue identified by includecheck
Signed-off-by: Hariprasad Kelam <hariprasad.kelam@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes, in particular in the
context in which this code is being used.

So, replace the following form:

sizeof(*kind) + sizeof(*kind->data) * mmu->kind_nr;

with:

struct_size(kind, data, mmu->kind_nr)

This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Drop use of the deprecated drmP.h file from drm/nouveau.

Build tested using allyesconfig and allmodconfig.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: nouveau@lists.freedesktop.org
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Drop include of the deprecated drmP.h from all nouveau heder files.
This allows us to remove drmP.h from all .c files without any
side-effects in a follow-up commit.

Build tested using allyeyconfig and allmodconfig
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: nouveau@lists.freedesktop.org
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Drop the deprecated drmP.h header from nouveau_drv.h.
Fix fallout in other parts of the driver.

Build tested using allmodconfig and allyesconfig.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: nouveau@lists.freedesktop.org
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

The DRM_UDELAY is a simple wrapper for udealy() and to be consistent
call udelay() direct like in may other places.
This avoids the need to pull in drm_os_linux.h when we later
drop drmP.h uses in nouveau.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: nouveau@lists.freedesktop.org
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

There is a spelling mistake in a warning message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Fix sparse warning:

drivers/gpu/drm/nouveau/nvkm/subdev/secboot/acr_r352.c:1092:1:
 warning: symbol 'acr_r352_ls_gpccs_func' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>