- 16 Oct, 2011 24 commits
-
-
Alex Deucher authored
commit 4f332844 upstream. If there are error flags in the aux status, retry the transaction. This makes aux much more reliable, especially on llano systems. Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Reviewed-by:
Michel Dänzer <michel.daenzer@amd.com> Signed-off-by:
Dave Airlie <airlied@redhat.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
srinidhi kasagar authored
commit 98e87d57 upstream. This applies ARM errata fix 754322 for all ux500 platforms. Signed-off-by:
srinidhi kasagar <srinidhi.kasagar@stericsson.com> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Tetsuo Handa authored
commit 91219352 upstream. Currently, search_binary_handler() tries to load binary loader module using request_module() if a loader for the requested program is not yet loaded. But second attempt of request_module() does not affect the result of search_binary_handler(). If request_module() triggered recursion, calling request_module() twice causes 2 to the power of MAX_KMOD_CONCURRENT (= 50) repetitions. It is not an infinite loop but is sufficient for users to consider as a hang up. Therefore, this patch changes not to call request_module() twice, making 1 to the power of MAX_KMOD_CONCURRENT repetitions in case of recursion. Signed-off-by:
Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Reported-by:
Richard Weinberger <richard@nod.at> Tested-by:
Andrew Morton <akpm@linux-foundation.org> Cc: Maxim Uvarov <muvarov@gmail.com> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
Koen Beel authored
commit d982dcdc upstream. Fix clock rate setting in the mxs-mmc driver. Previously, if div2 was 0 then the value for TIMING_CLOCK_RATE would have been 255 instead of 0. The limits for div1 (TIMING_CLOCK_DIVIDE) and div2 (TIMING_CLOCK_RATE+1) were also not correctly defined. Can easily be reproduced on mx23evk: default clock for high speed sdio cards is 50 MHz. With a SSP_CLK of 28.8 MHz default), this resulted in an actual clock rate of about 56 kHz. Tested on mx23evk. Signed-off-by:
Koen Beel <koen.beel@barco.com> Reviewed-by:
Wolfram Sang <w.sang@pengutronix.de> Signed-off-by:
Chris Ball <cjb@laptop.org> Signed-off-by:
-
Mike Snitzer authored
commit 876fbba1 upstream. Commit a63a5cf8 (dm: improve block integrity support) introduced a two-phase initialization of a DM device's integrity profile. This patch avoids dereferencing a NULL 'template_disk' pointer in blk_integrity_register() if there is an integrity profile mismatch in dm_table_set_integrity(). This can occur if the integrity profiles for stacked devices in a DM table are changed between the call to dm_table_prealloc_integrity() and dm_table_set_integrity(). Reported-by:
Zdenek Kabelac <zkabelac@redhat.com> Signed-off-by:
Mike Snitzer <snitzer@redhat.com> Signed-off-by:
Alasdair G Kergon <agk@redhat.com> Signed-off-by:
-
NeilBrown authored
commit 01f96c0a upstream. Two related problems: 1/ some error paths call "md_unregister_thread(mddev->thread)" without subsequently clearing ->thread. A subsequent call to mddev_unlock will try to wake the thread, and crash. 2/ Most calls to md_wakeup_thread are protected against the thread disappeared either by: - holding the ->mutex - having an active request, so something else must be keeping the array active. However mddev_unlock calls md_wakeup_thread after dropping the mutex and without any certainty of an active request, so the ->thread could theoretically disappear. So we need a spinlock to provide some protections. So change md_unregister_thread to take a pointer to the thread pointer, and ensure that it always does the required locking, and clears the pointer properly. Reported-by:
"Moshe Melnikov" <moshe@zadarastorage.com> Signed-off-by:
NeilBrown <neilb@suse.de> Signed-off-by:
-
Mark Salyzyn authored
commit a73914c3 upstream. When a wide port is being utilized to a target, if one disables only one of the phys, we get an OS crash: BUG: unable to handle kernel NULL pointer dereference at 0000000000000238 IP: [<ffffffff814ca9b1>] mutex_lock+0x21/0x50 PGD 4103f5067 PUD 41dba9067 PMD 0 Oops: 0002 [#1] SMP last sysfs file: /sys/bus/pci/slots/5/address CPU 0 Modules linked in: pm8001(U) ses enclosure fuse nfsd exportfs autofs4 ipmi_devintf ipmi_si ipmi_msghandler nfs lockd fscache nfs_acl auth_rpcgss 8021q fcoe libfcoe garp libfc scsi_transport_fc stp scsi_tgt llc sunrpc cpufreq_ondemand acpi_cpufreq freq_table ipv6 sr_mod cdrom dm_mirror dm_region_hash dm_log uinput sg i2c_i801 i2c_core iTCO_wdt iTCO_vendor_support e1000e mlx4_ib ib_mad ib_core mlx4_en mlx4_core ext3 jbd mbcache sd_mod crc_t10dif usb_storage ata_generic pata_acpi ata_piix libsas(U) scsi_transport_sas dm_mod [last unloaded: pm8001] Modules linked in: pm8001(U) ses enclosure fuse nfsd exportfs autofs4 ipmi_devintf ipmi_si ipmi_msghandler nfs lockd fscache nfs_acl auth_rpcgss 8021q fcoe libfcoe garp libfc scsi_transport_fc stp scsi_tgt llc sunrpc cpufreq_ondemand acpi_cpufreq freq_table ipv6 sr_mod cdrom dm_mirror dm_region_hash dm_log uinput sg i2c_i801 i2c_core iTCO_wdt iTCO_vendor_support e1000e mlx4_ib ib_mad ib_core mlx4_en mlx4_core ext3 jbd mbcache sd_mod crc_t10dif usb_storage ata_generic pata_acpi ata_piix libsas(U) scsi_transport_sas dm_mod [last unloaded: pm8001] Pid: 5146, comm: scsi_wq_5 Not tainted 2.6.32-71.29.1.el6.lustre.7.x86_64 #1 Storage Server RIP: 0010:[<ffffffff814ca9b1>] [<ffffffff814ca9b1>] mutex_lock+0x21/0x50 RSP: 0018:ffff8803e4e33d30 EFLAGS: 00010246 RAX: 0000000000000000 RBX: 0000000000000238 RCX: 0000000000000000 RDX: 0000000000000000 RSI: ffff8803e664c800 RDI: 0000000000000238 RBP: ffff8803e4e33d40 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000001 R12: 0000000000000000 R13: 0000000000000238 R14: ffff88041acb7200 R15: ffff88041c51ada0 FS: 0000000000000000(0000) GS:ffff880028200000(0000) knlGS:0000000000000000 CS: 0010 DS: 0018 ES: 0018 CR0: 000000008005003b CR2: 0000000000000238 CR3: 0000000410143000 CR4: 00000000000006f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 Process scsi_wq_5 (pid: 5146, threadinfo ffff8803e4e32000, task ffff8803e4e294a0) Stack: ffff8803e664c800 0000000000000000 ffff8803e4e33d70 ffffffffa001f06e <0> ffff8803e4e33d60 ffff88041c51ada0 ffff88041acb7200 ffff88041bc0aa00 <0> ffff8803e4e33d90 ffffffffa0032b6c 0000000000000014 ffff88041acb7200 Call Trace: [<ffffffffa001f06e>] sas_port_delete_phy+0x2e/0xa0 [scsi_transport_sas] [<ffffffffa0032b6c>] sas_unregister_devs_sas_addr+0xac/0xe0 [libsas] [<ffffffffa0034914>] sas_ex_revalidate_domain+0x204/0x330 [libsas] [<ffffffffa00307f0>] ? sas_revalidate_domain+0x0/0x90 [libsas] [<ffffffffa0030855>] sas_revalidate_domain+0x65/0x90 [libsas] [<ffffffff8108c7d0>] worker_thread+0x170/0x2a0 [<ffffffff81091ea0>] ? autoremove_wake_function+0x0/0x40 [<ffffffff8108c660>] ? worker_thread+0x0/0x2a0 [<ffffffff81091b36>] kthread+0x96/0xa0 [<ffffffff810141ca>] child_rip+0xa/0x20 [<ffffffff81091aa0>] ? kthread+0x0/0xa0 [<ffffffff810141c0>] ? child_rip+0x0/0x20 Code: ff ff 85 c0 75 ed eb d6 66 90 55 48 89 e5 48 83 ec 10 48 89 1c 24 4c 89 64 24 08 0f 1f 44 00 00 48 89 fb e8 92 f4 ff ff 48 89 df <f0> ff 0f 79 05 e8 25 00 00 00 65 48 8b 04 25 08 cc 00 00 48 2d RIP [<ffffffff814ca9b1>] mutex_lock+0x21/0x50 RSP <ffff8803e4e33d30> CR2: 0000000000000238 The following patch is admittedly a band-aid, and does not solve the root cause, but it still is a good candidate for hardening as a pointer check before reference. Signed-off-by:
Mark Salyzyn <mark_salyzyn@us.xyratex.com> Tested-by:
Jack Wang <jack_wang@usish.com> Signed-off-by:
James Bottomley <JBottomley@Parallels.com> Signed-off-by:
-
Roland Dreier authored
commit 9bfacd01 upstream. I hit a crash in qla2x00_abort_all_cmds() if the qla2xxx module is unloaded right after it is loaded. I debugged this down to the abort handling improperly treating a command of type SRB_ADISC_CMD as if it had a bsg_job to complete when that command actually uses the iocb_cmd part of the union. (I guess to hit this one has to unload the module while the async FC initialization is still in progress) It seems we should only look for a bsg_job if type is SRB_ELS_CMD_RPT, SRB_ELS_CMD_HST or SRB_CT_CMD, so switch the test to make that explicit. Signed-off-by:
Roland Dreier <roland@purestorage.com> Acked-by:
Chad Dupuis <chad.dupuis@qlogic.com> Signed-off-by:
-
Paul Menzel authored
commit 29cf7a30 upstream. In summary, this DMI quirk uses the _CRS info by default for the ASUS M2V-MX SE by turning on `pci=use_crs` and is similar to the quirk added by commit 2491762c ("x86/PCI: use host bridge _CRS info on ASRock ALiveSATA2-GLAN") whose commit message should be read for further information. Since commit 3e3da00c ("x86/pci: AMD one chain system to use pci read out res") Linux gives the following oops: parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE] HDA Intel 0000:20:01.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 HDA Intel 0000:20:01.0: setting latency timer to 64 BUG: unable to handle kernel paging request at ffffc90011c08000 IP: [<ffffffffa0578402>] azx_probe+0x3ad/0x86b [snd_hda_intel] PGD 13781a067 PUD 13781b067 PMD 1300ba067 PTE 800000fd00000173 Oops: 0009 [#1] SMP last sysfs file: /sys/module/snd_pcm/initstate CPU 0 Modules linked in: snd_hda_intel(+) snd_hda_codec snd_hwdep snd_pcm_oss snd_mixer_oss snd_pcm snd_seq_midi snd_rawmidi snd_seq_midi_event tpm_tis tpm snd_seq tpm_bios psmouse parport_pc snd_timer snd_seq_device parport processor evdev snd i2c_viapro thermal_sys amd64_edac_mod k8temp i2c_core soundcore shpchp pcspkr serio_raw asus_atk0110 pci_hotplug edac_core button snd_page_alloc edac_mce_amd ext3 jbd mbcache sha256_generic cryptd aes_x86_64 aes_generic cbc dm_crypt dm_mod raid1 md_mod usbhid hid sg sd_mod crc_t10dif sr_mod cdrom ata_generic uhci_hcd sata_via pata_via libata ehci_hcd usbcore scsi_mod via_rhine mii nls_base [last unloaded: scsi_wait_scan] Pid: 1153, comm: work_for_cpu Not tainted 2.6.37-1-amd64 #1 M2V-MX SE/System Product Name RIP: 0010:[<ffffffffa0578402>] [<ffffffffa0578402>] azx_probe+0x3ad/0x86b [snd_hda_intel] RSP: 0018:ffff88013153fe50 EFLAGS: 00010286 RAX: ffffc90011c08000 RBX: ffff88013029ec00 RCX: 0000000000000006 RDX: 0000000000000000 RSI: 0000000000000246 RDI: 0000000000000246 RBP: ffff88013341d000 R08: 0000000000000000 R09: 0000000000000040 R10: 0000000000000286 R11: 0000000000003731 R12: ffff88013029c400 R13: 0000000000000000 R14: 0000000000000000 R15: ffff88013341d090 FS: 0000000000000000(0000) GS:ffff8800bfc00000(0000) knlGS:00000000f7610ab0 CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b CR2: ffffc90011c08000 CR3: 0000000132f57000 CR4: 00000000000006f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 Process work_for_cpu (pid: 1153, threadinfo ffff88013153e000, task ffff8801303c86c0) Stack: 0000000000000005 ffffffff8123ad65 00000000000136c0 ffff88013029c400 ffff8801303c8998 ffff88013341d000 ffff88013341d090 ffff8801322d9dc8 ffff88013341d208 0000000000000000 0000000000000000 ffffffff811ad232 Call Trace: [<ffffffff8123ad65>] ? __pm_runtime_set_status+0x162/0x186 [<ffffffff811ad232>] ? local_pci_probe+0x49/0x92 [<ffffffff8105afc5>] ? do_work_for_cpu+0x0/0x1b [<ffffffff8105afc5>] ? do_work_for_cpu+0x0/0x1b [<ffffffff8105afd0>] ? do_work_for_cpu+0xb/0x1b [<ffffffff8105fd3f>] ? kthread+0x7a/0x82 [<ffffffff8100a824>] ? kernel_thread_helper+0x4/0x10 [<ffffffff8105fcc5>] ? kthread+0x0/0x82 [<ffffffff8100a820>] ? kernel_thread_helper+0x0/0x10 Code: f4 01 00 00 ef 31 f6 48 89 df e8 29 dd ff ff 85 c0 0f 88 2b 03 00 00 48 89 ef e8 b4 39 c3 e0 8b 7b 40 e8 fc 9d b1 e0 48 8b 43 38 <66> 8b 10 66 89 14 24 8b 43 14 83 e8 03 83 f8 01 77 32 31 d2 be RIP [<ffffffffa0578402>] azx_probe+0x3ad/0x86b [snd_hda_intel] RSP <ffff88013153fe50> CR2: ffffc90011c08000 ---[ end trace 8d1f3ebc136437fd ]--- Trusting the ACPI _CRS information (`pci=use_crs`) fixes this problem. $ dmesg | grep -i crs # with the quirk PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug The match has to be against the DMI board entries though since the vendor entries are not populated. DMI: System manufacturer System Product Name/M2V-MX SE, BIOS 0304 10/30/2007 This quirk should be removed when `pci=use_crs` is enabled for machines from 2006 or earlier or some other solution is implemented. Using coreboot [1] with this board the problem does not exist but this quirk also does not affect it either. To be safe though the check is tightened to only take effect when the BIOS from American Megatrends is used. 15:13 < ruik> but coreboot does not need that 15:13 < ruik> because i have there only one root bus 15:13 < ruik> the audio is behind a bridge $ sudo dmidecode BIOS Information Vendor: American Megatrends Inc. Version: 0304 Release Date: 10/30/2007 [1] http://www.coreboot.org/ Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=30552 Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: x86@kernel.org Signed-off-by:
Paul Menzel <paulepanter@users.sourceforge.net> Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> Acked-by:
Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by:
-
Gertjan van Wingerde authored
commit 77a861c4 upstream. The rt2x00 driver gets frequent occurrences of the following error message when operating under load: phy0 -> rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 2. This is caused by simultaneous attempts from mac80211 to send a frame via rt2x00, which are not properly serialized inside rt2x00queue_write_tx_frame, causing the second frame to fail sending with the above mentioned error message. Fix this by introducing a per-queue spinlock to serialize the TX operations on that queue. Reported-by:
Andreas Hartmann <andihartmann@01019freenet.de> Signed-off-by:
Gertjan van Wingerde <gwingerde@gmail.com> Acked-by:
Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by:
Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com> Cc: Tim Gardner <tim.gardner@canonical.com> Signed-off-by:
-
Richard Cochran authored
commit f75159e9 upstream. The IEEE 1588 standard defines two kinds of messages, event and general messages. Event messages require time stamping, and general do not. When using UDP transport, two separate ports are used for the two message types. The BPF designed to recognize event messages incorrectly classifies L2 general messages as event messages. This commit fixes the issue by extending the filter to check the message type field for L2 PTP packets. Event messages are be distinguished from general messages by testing the "general" bit. Signed-off-by:
Richard Cochran <richard.cochran@omicron.at> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Alex Deucher authored
commit 12d5180b upstream. Most asics just use the hw default value which requires no explicit programming. For those that need a different value, the vbios will program it properly. As such, there's no need to program these registers explicitly in the driver. Changing MC_SHARED_CHREMAP requires a reload of all data in vram otherwise its contents will be scambled. Fixes: https://bugs.freedesktop.org/show_bug.cgi?id=40103 v2: drop now unused channel_remap functions. Signed-off-by:
-
Alex Deucher authored
commit 6375bda0 upstream. The previous code could potentially loop forever. Limit the number of DP aux defer retries to 4 for native aux transactions, same as i2c over aux transactions. Noticed by: Brad Campbell <lists2009@fnarfbargle.com> Signed-off-by:
-
Alex Deucher authored
commit 109bc10d upstream. An incorrect ordering in the error checking code lead to DP aux defer being skipped in the aux native write path. Move the bytes transferred check (ret == 0) below the defer check. Tracked down by: Brad Campbell <brad@fnarfbargle.com> Fixes: https://bugs.freedesktop.org/show_bug.cgi?id=41121Signed-off-by:
-
Alex Deucher authored
commit 5ba7ddf8 upstream. Only disable the pipe if the monitor is physically disconnected. The previous logic also disabled the pipe if the link was trained. Fixes: https://bugs.freedesktop.org/show_bug.cgi?id=41248Signed-off-by:
-
Michel Dänzer authored
commit b8aee294 upstream. Fixes cursor disappearing prematurely when moving off a top/left edge which is not located at the desktop top/left edge. Signed-off-by:
-
Axel Lin authored
commit 21d17dd2 upstream. Current code set update bits for WM8753_LDAC and WM8753_RDAC twice, but missed setting update bits for WM8753_LADC and WM8753_RADC. I think it is a copy-paste bug in commit 776065 "ASoC: codecs: wm8753: Fix register cache incoherency". Signed-off-by:
Axel Lin <axel.lin@gmail.com> Signed-off-by:
Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by:
-
Arnd Bergmann authored
commit eff919ac upstream. A recent conversion has introduced references to &pdev->dev, which does not actually exist in all the contexts it's used in. Replace this with card->dev where necessary, in order to let the driver build again. Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Takashi Iwai authored
commit 05faadcf upstream. Commit 2a7fade7 ("hwmon: lis3: Power on corrections") caused a regression on HP laptops with 8bit chip. Writing CTRL2_BOOT_8B bit seems clearing the BIOS setup, and no proper interrupt for DriveGuard will be triggered any more. Since the init code there is basically only for embedded devices, put a pdata check so that the problematic initialization will be skipped for hp_accel stuff. Signed-off-by:
Takashi Iwai <tiwai@suse.de> Cc: Eric Piel <eric.piel@tremplin-utc.net> Cc: Samu Onkalo <samu.p.onkalo@nokia.com> Signed-off-by:
Andrew Morton <akpm@google.com> Signed-off-by:
-
Peter Zijlstra authored
commit d670ec13 upstream. David reported: Attached below is a watered-down version of rt/tst-cpuclock2.c from GLIBC. Just build it with "gcc -o test test.c -lpthread -lrt" or similar. Run it several times, and you will see cases where the main thread will measure a process clock difference before and after the nanosleep which is smaller than the cpu-burner thread's individual thread clock difference. This doesn't make any sense since the cpu-burner thread is part of the top-level process's thread group. I've reproduced this on both x86-64 and sparc64 (using both 32-bit and 64-bit binaries). For example: [davem@boricha build-x86_64-linux]$ ./test process: before(0.001221967) after(0.498624371) diff(497402404) thread: before(0.000081692) after(0.498316431) diff(498234739) self: before(0.001223521) after(0.001240219) diff(16698) [davem@boricha build-x86_64-linux]$ The diff of 'process' should always be >= the diff of 'thread'. I make sure to wrap the 'thread' clock measurements the most tightly around the nanosleep() call, and that the 'process' clock measurements are the outer-most ones. --- #include <unistd.h> #include <stdio.h> #include <stdlib.h> #include <time.h> #include <fcntl.h> #include <string.h> #include <errno.h> #include <pthread.h> static pthread_barrier_t barrier; static void *chew_cpu(void *arg) { pthread_barrier_wait(&barrier); while (1) __asm__ __volatile__("" : : : "memory"); return NULL; } int main(void) { clockid_t process_clock, my_thread_clock, th_clock; struct timespec process_before, process_after; struct timespec me_before, me_after; struct timespec th_before, th_after; struct timespec sleeptime; unsigned long diff; pthread_t th; int err; err = clock_getcpuclockid(0, &process_clock); if (err) return 1; err = pthread_getcpuclockid(pthread_self(), &my_thread_clock); if (err) return 1; pthread_barrier_init(&barrier, NULL, 2); err = pthread_create(&th, NULL, chew_cpu, NULL); if (err) return 1; err = pthread_getcpuclockid(th, &th_clock); if (err) return 1; pthread_barrier_wait(&barrier); err = clock_gettime(process_clock, &process_before); if (err) return 1; err = clock_gettime(my_thread_clock, &me_before); if (err) return 1; err = clock_gettime(th_clock, &th_before); if (err) return 1; sleeptime.tv_sec = 0; sleeptime.tv_nsec = 500000000; nanosleep(&sleeptime, NULL); err = clock_gettime(th_clock, &th_after); if (err) return 1; err = clock_gettime(my_thread_clock, &me_after); if (err) return 1; err = clock_gettime(process_clock, &process_after); if (err) return 1; diff = process_after.tv_nsec - process_before.tv_nsec; printf("process: before(%lu.%.9lu) after(%lu.%.9lu) diff(%lu)\n", process_before.tv_sec, process_before.tv_nsec, process_after.tv_sec, process_after.tv_nsec, diff); diff = th_after.tv_nsec - th_before.tv_nsec; printf("thread: before(%lu.%.9lu) after(%lu.%.9lu) diff(%lu)\n", th_before.tv_sec, th_before.tv_nsec, th_after.tv_sec, th_after.tv_nsec, diff); diff = me_after.tv_nsec - me_before.tv_nsec; printf("self: before(%lu.%.9lu) after(%lu.%.9lu) diff(%lu)\n", me_before.tv_sec, me_before.tv_nsec, me_after.tv_sec, me_after.tv_nsec, diff); return 0; } This is due to us using p->se.sum_exec_runtime in thread_group_cputime() where we iterate the thread group and sum all data. This does not take time since the last schedule operation (tick or otherwise) into account. We can cure this by using task_sched_runtime() at the cost of having to take locks. This also means we can (and must) do away with thread_group_sched_runtime() since the modified thread_group_cputime() is now more accurate and would deadlock when called from thread_group_sched_runtime(). Aside of that it makes the function safe on 32 bit systems. The old code added t->se.sum_exec_runtime unprotected. sum_exec_runtime is a 64bit value and could be changed on another cpu at the same time. Reported-by:
Peter Zijlstra <a.p.zijlstra@chello.nl> Link: http://lkml.kernel.org/r/1314874459.7945.22.camel@twinsTested-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
Borislav Petkov authored
commit 2c8fc867 upstream. Simon Kirby reported that on his RAID setup with idedisk underneath the box OOMs after a couple of days of runtime. Running with CONFIG_DEBUG_KMEMLEAK pointed to idedisk_prep_fn() which unconditionally allocates an ide_cmd struct. However, ide_requeue_and_plug() can be called more than once per request, either from the request issue or the IRQ handler path and do blk_peek_request() ends up in idedisk_prep_fn() repeatedly, allocating a struct ide_cmd everytime and "forgetting" the previous pointer. Make sure the code reuses the old allocated chunk. Reported-and-tested-by:
Simon Kirby <sim@hostway.ca> Link: http://marc.info/?l=linux-kernel&m=131667641517919 Link: http://lkml.kernel.org/r/20110922072643.GA27232@hostway.caSigned-off-by:
Borislav Petkov <bp@alien8.de> Signed-off-by:
-
Simon Kirby authored
commit 6ebbe7a0 upstream. Commit c259e01a ("sched: Separate the scheduler entry for preemption") contained a boo-boo wrecking wchan output. It forgot to put the new schedule() function in the __sched section and thereby doesn't get properly ignored for things like wchan. Tested-by:
Ingo Molnar <mingo@elte.hu> Signed-off-by:
-
Shawn Bohrer authored
commit 3be209a8 upstream. Commit 43fa5460 ("sched: Try not to migrate higher priority RT tasks") also introduced a change in behavior which keeps RT tasks on the same CPU if there is an equal priority RT task currently running even if there are empty CPUs available. This can cause unnecessary wakeup latencies, and can prevent the scheduler from balancing all RT tasks across available CPUs. This change causes an RT task to search for a new CPU if an equal priority RT task is already running on wakeup. Lower priority tasks will still have to wait on higher priority tasks, but the system should still balance out because there is always the possibility that if there are both a high and low priority RT tasks on a given CPU that the high priority task could wakeup while the low priority task is running and force it to search for a better runqueue. Signed-off-by:
Shawn Bohrer <sbohrer@rgmadvisors.com> Acked-by:
Steven Rostedt <rostedt@goodmis.org> Tested-by:
-
David S. Miller authored
In the OF 'translations' property, the template TTEs in the mappings never specify the executable bit. This is the case even though some of these mappings are for OF's code segment. Therefore, we need to force the execute bit on in every mapping. This problem can only really trigger on Niagara/sun4v machines and the history behind this is a little complicated. Previous to sun4v, the sun4u TTE entries lacked a hardware execute permission bit. So OF didn't have to ever worry about setting anything to handle executable pages. Any valid TTE loaded into the I-TLB would be respected by the chip. But sun4v Niagara chips have a real hardware enforced executable bit in their TTEs. So it has to be set or else the I-TLB throws an instruction access exception with type code 6 (protection violation). We've been extremely fortunate to not get bitten by this in the past. The best I can tell is that the OF's mappings for it's executable code were mapped using permanent locked mappings on sun4v in the past. Therefore, the fact that we didn't have the exec bit set in the OF translations we would use did not matter in practice. Thanks to Greg Onufer for helping me track this down. Signed-off-by:
-
- 03 Oct, 2011 16 commits
-
-
Greg Kroah-Hartman authored
-
Dave Airlie authored
commit d9ad77eb upstream. This reverts commit 18b4fada. This code was correct, apologies to anyone who noticed things broke. revert contents are different due to another commit in between. Signed-off-by:
-
Greg Kroah-Hartman authored
-
David Henningsson authored
commit 46724c2e upstream. BugLink: http://bugs.launchpad.net/bugs/854468Signed-off-by:
David Henningsson <david.henningsson@canonical.com> Signed-off-by:
-
Hannes Reinecke authored
commit 777eb1bf upstream. A kernel crash is observed when a mounted ext3/ext4 filesystem is physically removed. The problem is that blk_cleanup_queue() frees up some resources eg by calling elevator_exit(), which are not checked for in normal operation. So we should rather move these calls to the destructor function blk_release_queue() as at that point all remaining references are gone. However, in doing so we have to ensure that any externally supplied queue_lock is disconnected as the driver might free up the lock after the call of blk_cleanup_queue(), Signed-off-by:
Hannes Reinecke <hare@suse.de> Signed-off-by:
Jens Axboe <axboe@kernel.dk> Signed-off-by:
-
Shmulik Ravid authored
commit a0babc80 upstream. Signed-off-by:
Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by:
Eilon Greenstein <eilong@broadcom.com> Signed-off-by:
-
Dmitry Kravkov authored
commit f2eaeb58 upstream. Use register name to initialize attention mask Signed-off-by:
-
Johannes Berg authored
commit 6c80c39d upstream. If iwl_scan_initiate() fails for any reason, priv->scan_request and priv->scan_vif are left dangling. This can lead to a crash later when iwl_bg_scan_completed() tries to run a pending scan request. In practice, this seems to be very rare due to the STATUS_SCANNING check earlier. That check, however, is wrong -- it should allow a scan to be queued when a reset/roc scan is going on. When a normal scan is already going on, a new one can't be issued by mac80211, so that code can be removed completely. I introduced this bug when adding off-channel support in commit 266af4c7. Reported-by:
Peng Yan <peng.yan@intel.com> Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by:
-
Stanislaw Gruszka authored
commit 65d0f19e upstream. iwlegacy version of fix: commit effd4d9a Author: Johannes Berg <johannes.berg@intel.com> Date: Thu Sep 15 11:46:52 2011 -0700 iwlagn: do not use interruptible waits Since the dawn of its time, iwlwifi has used interruptible waits to wait for synchronous commands and firmware loading. This leads to "interesting" bugs, because it can't actually handle the interruptions; for example when a command sending is interrupted it will assume the command completed fully, and then leave it pending, which leads to all kinds of trouble when the command finishes later. Since there's no easy way to gracefully deal with interruptions, fix the driver to not use interruptible waits. This at least fixes the error iwlagn 0000:02:00.0: Error: Response NULL in 'REPLY_SCAN_ABORT_CMD' I have seen in P2P testing, but it is likely that there are other errors caused by this. Signed-off-by:
Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by:
-
Larry Finger authored
commit 831d8547 upstream. Driver rtl8192cu assigns a new struct rtl_tcb_desc object, but fails to clear it. Signed-off-by:
Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by:
-
Stanislaw Gruszka authored
commit 2e2a41d6 upstream. iwlegacy version of fix: commit 282cdb32 Author: Johannes Berg <johannes.berg@intel.com> Date: Mon Sep 12 12:09:10 2011 -0700 iwlagn: fix command queue timeout If the command queue is constantly busy, which can happen in P2P, the hangcheck timer will frequently find a command in it and will eventually reset the device because nothing sets the timestamp for this queue when commands are processed. Fix this by setting the timestamp when a command completes. iwlegacy does not support P2P, but this patch fix possible unneeded hardware resets, hence is needed. Signed-off-by:
-
Rajkumar Manoharan authored
commit e9f9530b upstream. During the endurance testing, rx frames are not getting DMAd from MAC whereas pcu rx frame counters are getting updated properly. As per systems team input updated the initval to fix rx dma stuck issue. Signed-off-by:
Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by:
-
Jouni Malinen authored
commit 1b9ca027 upstream. Incorrect variable was used in validating the akm_suites array from NL80211_ATTR_AKM_SUITES. In addition, there was no explicit validation of the array length (we only have room for NL80211_MAX_NR_AKM_SUITES). This can result in a buffer write overflow for stack variables with arbitrary data from user space. The nl80211 commands using the affected functionality require GENL_ADMIN_PERM, so this is only exposed to admin users. Signed-off-by:
Jouni Malinen <jouni@qca.qualcomm.com> Signed-off-by:
-
Randy Dunlap authored
commit 3538a001 upstream. qla4xxx driver needs to be linked with libiscsi.o to fix build errors. This happens when no other drivers that use libiscsi.o are enabled. ERROR: "iscsi_conn_stop" [drivers/scsi/qla4xxx/qla4xxx.ko] undefined! ERROR: "iscsi_conn_get_addr_param" [drivers/scsi/qla4xxx/qla4xxx.ko] undefined! ERROR: "iscsi_session_teardown" [drivers/scsi/qla4xxx/qla4xxx.ko] undefined! ERROR: "iscsi_host_alloc" [drivers/scsi/qla4xxx/qla4xxx.ko] undefined! ERROR: "iscsi_conn_start" [drivers/scsi/qla4xxx/qla4xxx.ko] undefined! ERROR: "iscsi_conn_send_pdu" [drivers/scsi/qla4xxx/qla4xxx.ko] undefined! ERROR: "iscsi_session_get_param" [drivers/scsi/qla4xxx/qla4xxx.ko] undefined! ERROR: "iscsi_conn_get_param" [drivers/scsi/qla4xxx/qla4xxx.ko] undefined! ERROR: "iscsi_set_param" [drivers/scsi/qla4xxx/qla4xxx.ko] undefined! ERROR: "iscsi_session_failure" [drivers/scsi/qla4xxx/qla4xxx.ko] undefined! ERROR: "iscsi_complete_pdu" [drivers/scsi/qla4xxx/qla4xxx.ko] undefined! ERROR: "iscsi_session_setup" [drivers/scsi/qla4xxx/qla4xxx.ko] undefined! ERROR: "iscsi_conn_bind" [drivers/scsi/qla4xxx/qla4xxx.ko] undefined! ERROR: "iscsi_conn_setup" [drivers/scsi/qla4xxx/qla4xxx.ko] undefined! ERROR: "iscsi_itt_to_task" [drivers/scsi/qla4xxx/qla4xxx.ko] undefined! Signed-off-by:
Randy Dunlap <rdunlap@xenotime.net> Reviewed-by:
Mike Christie <michaelc@cs.wisc.edu> Signed-off-by:
-
Mark Salyzyn authored
commit 24926dad upstream. In an enclosure model where there are chaining expanders to a large body of storage, it was discovered that libsas, responding to a broadcast event change, would only revalidate the domain of first child expander in the list. The issue is that the pointer value to the discovered source device was used to break out of the loop, rather than the content of the pointer. This still remains non-compliant as the revalidate domain code is supposed to loop through all child expanders, and not stop at the first one it finds that reports a change count. However, the design of this routine does not allow multiple device discoveries and that would be a more complicated set of patches reserved for another day. We are fixing the glaring bug rather than refactoring the code. Signed-off-by:
Mark Salyzyn <msalyzyn@us.xyratex.com> Signed-off-by:
-
Vasily Averin authored
commit d0efab26 upstream. scsi reset on hardware with enabled MSI interrupts generates WARNING message [11027.798722] aacraid: Host adapter abort request (0,0,0,0) [11027.798814] aacraid: Host adapter reset request. SCSI hang ? [11087.762237] aacraid: SCSI bus appears hung [11135.082543] ------------[ cut here ]------------ [11135.082646] WARNING: at drivers/pci/msi.c:658 pci_enable_msi_block+0x251/0x290() Signed-off-by:
Vasily Averin <vvs@sw.ru> Acked-by:
-
