setup_initial_memory_limit() is only called during init.
mmu_patch_cmp_limit() is only called from 8xx_mmu.c
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Pinning TLBs bypasses STRICT_KERNEL_RWX or DEBUG_PAGEALLOC protections
so it should only be allowed when those are not selected
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

As stated in a comment in head_8xx.S, today we "Always pin the first
8 MB ITLB to prevent ITLB misses while mucking around with SRR0/SRR1
in asm".

This issue has just been cleared by the preceding patch, therefore
we can make this pinning optional (on by default) and independent
of DATA pinning.

This patch also makes pinning of IMMR independent of pinning of DATA.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

By default, the 8xx pins an ITLB on the first 8M of memory in order
to avoid any ITLB miss on kernel code.
However, with some debug functions like DEBUG_PAGEALLOC and
DEBUG_RODATA, pinning TLBs is contradictory.

In order to avoid any ITLB miss in a critical section without pinning
TLBs, we have to ensure that there is no page boundary crossed between
the setup of a new value in SRR0/SRR1 and the associated RFI.

The functions modifying srr0/srr1 are all located in setup_32.S.
They are spread over almost 4kbytes.

The patch forces a 12 bits (4kbytes) alignment for those
functions. This garanties that the functions remain in a
single 4k page.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

The macro to check if an address is a kernel address or not is
not used anymore in DTLBmiss handler. It is used in ITLB miss handler
and in DTLB error handler. DTLB error handler is not a hot path, it
doesn't need such optimisation.

In order to simplify a following patch which will rework ITLB miss
handler, we remove the macros and reintroduce them inside the handler.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

On the 8xx, the RAM mapped with LTLBs must be seen as block mapped,
just like areas mapped with BATs on standard PPC32.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Normally the values in the resource field and the argument to ARRAY_SIZE
in the num_resources are the same.  In this case, the value in the reousrce
field is the same as the one in the previous platform_device structure, and
appears to be a copy-paste error.  Replace the value in the resource field
with the argument to the local call to ARRAY_SIZE.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

This fixes another invalid use of register expressions.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

In iommu_range_alloc() we generate a mask by right shifting ~0,
however if the specified alignment is 0 then we right shift by 64,
which is undefined. UBSAN tells us so:

  UBSAN: Undefined behaviour in ../arch/powerpc/kernel/iommu.c:193:35
  shift exponent 64 is too large for 64-bit type 'long unsigned int'

We can avoid it by instead generating the mask with:

  align_mask = (1ull << align_order) - 1;

That will also generate an undefined shift if align_order is 64 or
greater, but that shouldn't be a problem for a while.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

In a multi node system with discontiguous node ids, nest event values
are not showing up properly. eg. lscpu output:

  NUMA node0 CPU(s): 0-15
  NUMA node8 CPU(s): 16-31

Nest event values on such systems can be counted on CPUs <= 15:

  $./perf stat -e 'nest_powerbus0_imc/PM_PB_CYC/' -C 0-14 -I 1000 sleep 1000
  #           time             counts unit events
       1.000294577    30,17,24,42,880 nest_powerbus0_imc/PM_PB_CYC/

But not on CPUs >= 16:

  $./perf stat -e 'nest_powerbus0_imc/PM_PB_CYC/' -C 16-28 -I 1000 sleep 1000
  #           time             counts unit events
       1.000049902    <not supported> nest_powerbus0_imc/PM_PB_CYC/

This is because, when fetching the reference count, the node id (which
may be sparse) is used as the array index, not the node number (which
is 0 based and contiguous).

Fix it by using the node number as the array index.

  $./perf stat -e 'nest_powerbus0_imc/PM_PB_CYC/' -C 16-28 -I 1000 sleep 1000
  #           time             counts unit events
       1.000241961    26,12,35,28,704 nest_powerbus0_imc/PM_PB_CYC/
Signed-off-by: Anju T Sudhakar <anju@linux.vnet.ibm.com>
[mpe: Change log tweaks for clarity and brevity]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

In some obscure Book3E configs (randconfig) we can end up missing a
definition for PGALLOC_GFP in pgtable_64.c.

Fix it by moving the definition to asm/pgalloc.h.

Fixes: de3b8761 ("powerpc/mm/book(e)(3s)/64: Add page table accounting")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Exclude core xmon files from ftrace (along with an xmon xive helper
outside of xmon/) to minimize impact of ftrace while within xmon.

Before:
  /sys/kernel/debug/tracing# grep -ci xmon available_filter_functions
  26

After:
  /sys/kernel/debug/tracing# grep -ci xmon available_filter_functions
  0
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
[mpe: Use $(subst ..) on KBUILD_CFLAGS rather than CFLAGS_REMOVE_xxx]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

If tracing is enabled and you get into xmon, the tracing buffer
continues to be updated, causing possible loss of data and unnecessary
tracing information coming from xmon functions.

This patch simple disables tracing when entering xmon, and re-enables it
if the kernel is resumed (with 'x').
Signed-off-by: Breno Leitao <leitao@debian.org>
Acked-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Current xmon 'dt' command dumps the tracing buffer for all the CPUs,
which makes it very hard to read due to the fact that most of
powerpc machines currently have many CPUs. Other than that, the CPU
lines are interleaved in the ftrace log.

This new option just dumps the ftrace buffer for the current CPU.
Signed-off-by: Breno Leitao <leitao@debian.org>
Acked-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Make wf_control_ops const as they are only stored in the ops field of a
wf_control structure, which is const.
Make wf_pid_param const as they are only used during a copy operation.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

This function is not called with the nest_init_lock held, and it also
unlocks the nest_init_lock immediately below, so it's fairly clear
that this is a typo and should be locking the lock.

Fixes: 885dcd70 ("powerpc/perf: Add nest IMC PMU support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Commit 968159c0 ("powerpc/8xx: Getting rid of remaining use of
CONFIG_8xx") removed all but 2 references to 8xx in Kconfigs.

This patch removes the two remaining ones.

Fixes: 968159c0 ("powerpc/8xx: Getting rid of remaining use of CONFIG_8xx")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Both xive_core_init() and xive_native_init() are called from and call
__init routines, so they should also be __init.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

early_check_vec5() is called from and calls __init routines, so should
also be __init.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

head_8xx is dedicated to 8xx so no need to use macros that
depends on the CPU
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Use symbolic names for DSISR bits in DSI
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

For the 8xx, PVR values defined in arch/powerpc/include/asm/reg.h
are nowhere used.

Remove all defines and add PVR_8xx

Use it in arch/powerpc/kernel/cputable.c
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Two config options exist to define powerpc MPC8xx:
* CONFIG_PPC_8xx
* CONFIG_8xx

arch/powerpc/platforms/Kconfig.cputype has contained the following
comment about CONFIG_8xx item for some years:
"# this is temp to handle compat with arch=ppc"

There is no more users of CONFIG_8xx, so remove it.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Two config options exist to define powerpc MPC8xx:
* CONFIG_PPC_8xx
* CONFIG_8xx

arch/powerpc/platforms/Kconfig.cputype has contained the following
comment about CONFIG_8xx item for some years:
"# this is temp to handle compat with arch=ppc"

arch/powerpc is now the only place with remaining use of
CONFIG_8xx: get rid of them.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

4xx, CPM2 and 8xx cannot be selected at the same time, so
no need to test 8xx && !4xx && !CPM2. Testing 8xx is enough.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

The 8xx cannot access the TBL and TBU registers using mfspr/mtspr
It must be accessed using mftb/mftbu

Due to this, there is a number of places with #ifdef CONFIG_8xx

This patch defines new macros MFTBL(x) and MFTBU(x) on the same model
as MFTB(x) and tries to make use of them as much as possible.

In arch/powerpc/include/asm/timex.h, we also remove the ifdef
for the asm() operands as the compiler doesn't mind unused operands
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

mpc8xx_pic.c is dedicated to the 8xx, so move it to platform/8xx
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

To remain consistent with what is done with CPM2, let's link
CPM1 related parts to CONFIG_CPM1 instead of CONFIG_8xx

When something depends on both CPM1 and CPM2 we associate it
with CONFIG_CPM
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Since commit aa42c69c ("[POWERPC] Add support for FP emulation
for the e300c2 core"), program_check_exception() can be called for
math emulation. In that case, 'reason' is 0.

On the 8xx, there is a Software Emulation interrupt which is
called for all unimplemented and illegal instructions. This
interrupt calls SoftwareEmulation() which does almost the
same as program_check_exception() called with reason = 0.

The Software Emulation interrupt sets all reason bits to 0,
it is therefore possible to call program_check_exception()
directly from the interrupt handler.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

In the same spirit as what was done for 4xx and 44x, move
the 8xx machine check into platforms/8xx
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

The entire 8xx directory is omitted if CONFIG_8xx is not enabled, so
within the 8xx/Makefile CONFIG_8xx is always y. So convert
obj-$(CONFIG_8xx) to the more obvious obj-y.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Currently we open code the reason codes for program checks. Instead use
the existing SRR1 defines.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

We already have mce.c which is built for 64bit and contains other parts
of the machine check code, so move these bits in there too.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Make it clear that the fallback version of machine_check_generic() is
only used on 32-bit configs.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

get_mc_reason() no longer provides (if it ever really did) any
meaningful abstraction, so remove it.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Now that we have 4xx platform directory we can move the 4xx machine
check handler in there. Again we drop get_mc_reason() and replace it
with regs->dsisr directly (which is actually SPRN_ESR).
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

We have a lot of code in sysdev for supporting 4xx, ie. either 40x or
44x. Instead it would be cleaner if it was all in platforms/4xx.

This is slightly odd in that we don't actually define any machines in
the 4xx platform, as is usual for a platform directory. But still it
seems like a better result to have all this related code in a directory
by itself.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

We have several 44x machine check handlers defined in traps.c. It would
be preferable if they were split out with the platforms that use them.
Do that.

In the process, drop get_mc_reason() and instead just open code the
lookup of reason from regs->dsisr. This avoids a pointless layer of
abstraction.

We know to use regs->dsisr because 44x enables BOOKE which enables
PPC_ADV_DEBUG_REGS, and FSL_BOOKE is not enabled on 44x builds.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

The entire 44x directory is omitted if CONFIG_44x is not enabled, so
within the 44x/Makefile CONFIG_44x is always y. So convert
obj-$(CONFIG_44x) to the more obvious obj-y.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Currently we build the 47x cputable entries even when CONFIG_PPC_47x is
disabled. That means a kernel built without CONFIG_PPC_47x will claim to
support a 47x CPU and start booting, only to break somewhere later
because it doesn't have 47x support compiled in.

So guard the 47x cputable entries with CONFIG_PPC_47x. Note that this is
inside the #ifdef CONFIG_44x section, because 47x depends on 44x.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>