There is no need to configure the enabled ports once in b53_setup() and then a
second time around when dsa_switch_ops::port_enable is called, just do it when
port_enable is called which is better in terms of power consumption and
correctness.
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation for future changes allowing the configuring of multiple
CPU ports, make b53_enable_cpu_port() take a port argument.
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is not used anywhere, so remove it.
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vivien Didelot says:

====================
net: dsa: move master ethtool code

The DSA core overrides the master device's ethtool_ops structure so that
it can inject statistics and such of its dedicated switch CPU port.

This ethtool code is currently called on unnecessary conditions or
before the master interface and its switch CPU port get wired up.
This patchset fixes this.

Similarly to slave.c where the DSA slave net_device is the entry point
of the dsa_slave_* functions, this patchset also isolates the master's
ethtool code in a new master.c file, where the DSA master net_device is
the entry point of the dsa_master_* functions.

This is a first step towards better control of the master device and
support for multiple CPU ports.
====================
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

DSA overrides the master device ethtool ops, so that it can inject stats
from its dedicated switch CPU port as well.

The related code is currently split in dsa.c and slave.c, but it only
scopes the master net device. Move it to a new master.c DSA core file.

This file will be later extented with master net device specific code.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

DSA overrides the master's ethtool ops so that we can inject its CPU
port's statistics. Because of that, we need to setup the ethtool ops
after the master's dsa_ptr pointer has been assigned, not before.

This patch setups the ethtool ops after dsa_ptr is assigned, and
restores them before it gets cleared.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a DSA switch tree is meant to be applied, it already has a CPU
port. Thus remove the condition of dst->cpu_dp.

Moreover, the next lines access dst->cpu_dp unconditionally.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no need to store a copy of the master ethtool ops, storing the
original pointer in DSA and the new one in the master netdev itself is
enough.

In the meantime, set orig_ethtool_ops to NULL when restoring the master
ethtool ops and check the presence of the master original ethtool ops as
well as its needed functions before calling them.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

skb->rbnode shares space with skb->next, skb->prev and skb->tstamp

Current uses (TCP receive ofo queue and netem) need to save/restore
tstamp, while skb->dev is either NULL (TCP) or a constant for a given
queue (netem).

Since we plan using an RB tree for TCP retransmit queue to speedup SACK
processing with large BDP, this patch exchanges skb->dev and
skb->tstamp.

This saves some overhead in both TCP and netem.

v2: removes the swtstamp field from struct tcp_skb_cb
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Cc: Wei Wang <weiwan@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jiri Pirko says:

====================
mlxsw: Prepare for multicast router offload

Yotam says:

This patch-set makes various preparations needed for the multicast router
offloading, which include:
 - Add the needed registers.
 - Add needed ACL actions.
 - Add new traps and trap groups.
 - Exporting needed private structs and enums.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add three new traps needed for multicast routing:
 - PIM: Trap for PIM protocol control packets.
 - RPF: Trap for packets that fail the RPF check on a specific hardware
   route entry.
 - MULTICAST: Generic trap for multicast. It is used for routes that trap
   the packets to the CPU.

The RPF and MULTICAST traps have rate limiters as these traps may have
line-rate of packets trapped. The PIM trap has a rate limiter similarly to
other L3 control protocols. The rate limiters are implemented by adding
three new trap groups for the newly introduced traps.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The mlxsw_sp_rif struct, defined as private struct in spectrum_router.c
will be used in the multicast router source file. Due to the fact that the
dev field will be needed by the multicast router logic, add an access
function to it.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Turn on two bits on the Spectrum RIF configuration:
 - IPv4 multicast: when a multicast packet arrives on a RIF, send it to go
   through multicast routes lookup.
 - IPv4 multicast forwarding enable: when multicast packet arrives on a
   RIF, allow it to be forwarded by multicast routes. If this bit is not
   set, multicast packets will go through multicast routing lookup but will
   be dropped at the egress of the ports.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The RRCR register is used for copying and moving TCAM multicast routes
from different offsets. It will be used to allow routes relocation for
parman ops as part of the multicast router offloading logic.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The RMFT-V2 register is used to configure and query the multicast table and
will be used by the multicast router offloading logic.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The multicast ERIF list entries resource indicates the number of entries
that can be put in one rigr2 register operation. While the register can
hold up to MLXSW_REG_RIGR2_MAX_ERIFS ( = 32) ERIF entries, the actual
number allowed by firmware is indicated with this resource.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The RIGR-V2 register is used to add, remove and query egress interface list
of a multicast forwarding entry and it will be used by the multicast
router offloading logic.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This register is used for allocation of regions in the TCAM table and it
will be used by the multicast router offloading logic.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The MLXSW_REG_PXXX_FLEX_ACTION_SET_LEN is relevant for the multicast router
registers too, so rename it to have a general name which is not bound to a
specific register.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allow the trap ACL action to be configured with different traps. This
allows the multicast router offloading code to use that same ACL action
with the multicast router traps. By using different traps, the multicast
router can have different trap policies and can handle the packet
differently.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Spectrum multicast forwarding is done using an ACL action. Add the
mcrouter ACL action that will be used to offload the multicast router
logic.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A flexible action instance allows, given a set of ops, creating, committing
and sharing a set of ACL action blocks. The flexible action instance in
question is using the spectrum KVD linear space to store the flexible
action sets.

Move this flexible action instance to the common spectrum struct to allow
other users (such as multicast router) to get that functionality.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The multicast router offloading code is going to require the counter_pools
initialization to occur before the router initialization, thus, change the
spectrum initialization order to fix it.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Craig Gallek says:

====================
Implement delete for BPF LPM trie

This was previously left as a TODO.  Add the implementation and
extend the test to cover it.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Extend the 'random' operation tests to include a delete operation
(delete half of the nodes from both lpm implementions and ensure
that lookups are still equivalent).

Also, add a simple IPv4 test which verifies lookup behavior as nodes
are deleted from the tree.
Signed-off-by: Craig Gallek <kraig@google.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

The 'trivial' lpm implementation in this test allows equivalent nodes
to be added (that is, nodes consisting of the same prefix and prefix
length).  For lookup operations, this is fine because insertion happens
at the head of the (singly linked) list and the first, best match is
returned.  In order to support deletion, the tlpm data structue must
first enforce uniqueness.  This change modifies the insertion algorithm
to search for equivalent nodes and remove them.  Note: the
BPF_MAP_TYPE_LPM_TRIE already has a uniqueness invariant that is
implemented as node replacement.
Signed-off-by: Craig Gallek <kraig@google.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is a simple non-recursive delete operation.  It prunes paths
of empty nodes in the tree, but it does not try to further compress
the tree as nodes are removed.
Signed-off-by: Craig Gallek <kraig@google.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/vmw_vsock/vmci_transport.c does not use any miscdevice so this patch
remove this unnecessary inclusion.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove a goto in the PPv2 tx function which jumps to the next line
anyway. This is a cosmetic commit.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

HTB qdisc overlimits counter is properly increased, but we have no per
class counter, meaning it is difficult to diagnose HTB problems.

This patch adds this counter, visible in "tc -s class show dev eth0",
with current iproute2.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Denys Fedoryshchenko <nuclearcat@nuclearcat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pointer tcm is being initialized and is never read, it is only being used
to determine the size of struct tcmsg.  Clean this up by removing
variable tcm and explicitly using the sizeof struct tcmsg rather than *tcm.
Cleans up clang warning:

warning: Value stored to 'tcm' during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Roman Yeryomin says:

====================
korina: performance fixes and cleanup

Changes from v1:
- use GRO instead of increasing ring size
- use NAPI_POLL_WEIGHT instead of defining own NAPI_WEIGHT
- optimize rx descriptor flags processing
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Roman Yeryomin <roman@advem.lv>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Roman Yeryomin <roman@advem.lv>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Roman Yeryomin <roman@advem.lv>
Signed-off-by: David S. Miller <davem@davemloft.net>

Performance gain when receiving locally is 55->95Mbps and 50->65Mbps for NAT.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Roman Yeryomin <roman@advem.lv>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Roman Yeryomin <roman@advem.lv>
Signed-off-by: David S. Miller <davem@davemloft.net>

When such interrupts occur there is not much we can do.
Dropping the whole ring doesn't help and only produces high packet loss.
If we just ignore the interrupt the mac will drop one or few packets instead of the whole ring.
Also this will lower the irq handling load and increase performance.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
Signed-off-by: David S. Miller <davem@davemloft.net>