The PCI revision id determines the sku.
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

When doing a GPU reset or unloading the driver, we need to
put the SMU into the apprpriate state for the re-init after
the reset or unload to reliably work.

I don't think this is necessary for BACO because the SMU actually
controls the BACO state to it needs to be active.

For suspend (S3), the asic is put into D3 so the SMU would be
powered down so I don't think we need to put the SMU into
any special state.
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This sets the SMU into the proper state for various
operations (shutdown, unload, GPU reset, etc.).
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This sets the SMU into the proper state for various
operations (shutdown, unload, GPU reset, etc.).
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This sets the SMU into the proper state for various
operations (shutdown, unload, GPU reset, etc.).
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Some asics (APUs) don't have this callback so we want to return
success.  Avoids spurious error messages on APUs.
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This is required for certain cases such as various GPU resets
(mode1, mode2), BACO, shutdown, unload, etc. to put the SMU into
the appropriate state for when the hw is re-initialized.
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Navi uses either mode1 or baco depending on various
conditions.
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

APUs only support mode2 reset.  dGPUs use either mode1 or
baco depending on various conditions.
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

VI always uses the legacy pci based reset.
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

CIK always uses the legacy pci based reset.
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

SI always uses the legacy pci based reset.
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Sometimes the driver may have to behave differently depending
on the method we are using to reset the GPU.
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Move SMU irq handler register to sw_init as that's totally
software related. Otherwise, it will prevent SMU reset working.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

DPM state relates are not supported on the new SW SMU ASICs. But still
it's not OK to trigger null pointer dereference on accessing them.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Add checking for possible invalid input and null pointer. And
drop redundant code.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

enables gpu_vm_support in dm and adds
AMDGPU_GEM_DOMAIN_GTT as supported domain

v2:
Move BO placement logic into amdgpu_display_supported_domains

v3:
Use amdgpu_bo_validate_uswc in amdgpu_display_supported_domains.

v4:
amdgpu_bo_validate_uswc moved to sepperate patch.
Signed-off-by: Shirish S <shirish.s@amd.com>
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This verifies we don't add GTT as allowed domain for APUs when USWC
is disabled.
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Acked-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Move the logic to clear AMDGPU_GEM_CREATE_CPU_GTT_USWC in
amdgpu_bo_do_create into standalone helper so it can be reused
in other functions.

v4:
Switch to return bool.

v5: Fix typos.
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Acked-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

HW requires for caching to be unset for scanout BO
mappings when the BO placement is in GTT memory.
Usually the flag to unset is passed from user mode
but for FB mode this was missing.

v2:
Keep all BO placement logic in amdgpu_display_supported_domains
Suggested-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Tested-by: Shirish S <shirish.s@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

monitor xgmi errors via mc pie status through fica registers.
Signed-off-by: Jonathan Kim <Jonathan.Kim@amd.com>
Reviewed-by: Kent Russell <Kent.Russell@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

adding perfmon and fica atomic operations to adhere to data fabrics finite
state machine requirements for indirect register access.
Signed-off-by: Jonathan Kim <Jonathan.Kim@amd.com>
Reviewed-by: Kent Russell <Kent.Russell@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Jay Cornwall <jay.cornwall@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Previously submitted code was taken from an incorrect branch and
was non-functional.

Cc: Oak Zeng <oak.zeng@amd.com>
Signed-off-by: Jay Cornwall <jay.cornwall@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-By: Oak Zeng <oak.zeng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

If the trap is entered due to MODE.DEBUG_EN=1 and SAVECTX is raised
concurrently the handler cannot identify the source of the exception.
This causes the debugger to lose single step exception notification
when a context save request arrives at the same time.

When MODE.DEBUG_EN=1 and STATUS.HALT=0 (exception not already handled)
jump to the second-level trap handler upon entering the trap. The
second-level trap will set STATUS.HALT=1 and return to the shader.
If SAVECTX was raised then control flow will return to the trap, which
will then handle the context save request.

Cc: Tony Tye <tony.tye@amd.com>
Cc: Laurent Morichetti <laurent.morichetti@amd.com>
Cc: Qingchuan Shi <qingchuan.shi@amd.com>
Signed-off-by: Jay Cornwall <jay.cornwall@amd.com>
Reviewed-by: Laurent Morichetti <laurent.morichetti@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

When a wavefront raises TRAPSTS.XNACK_ERROR with STATUS.ALLOW_REPLAY=0
subsequent memory instructions have undefined behavior. In practice
SQC stores continue to work but TCP stores do not.

Context save is permitted to fail after XNACK error because the
wavefront will be halted and subsequently terminated. However the
debugger has an interest in retrieving the wavefront VGPR/LDS state.

Detect the out-of-spec case and use SQC stores during context save
in place of TCP stores.
Signed-off-by: Jay Cornwall <jay.cornwall@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

navi14 share same PTE format with navi10.
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: tiancyin <tianci.yin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Since we are using the signed FW now, and also using PSP firmware loading,
but it's still potential to break driver when loading FW directly
instead of PSP, so we should add offset.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

in this patch,
drm/amd/powerplay: add callback function of get_thermal_temperature_range
the driver missed temperature granularity change on other temperature.
Signed-off-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Drop redundant check, duplicate check, duplicate setting
and fix the return value.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Honor the 'dpm' module parameter setting on SW SMU routine as what
we did on previous ASICs. SMU FW loading is still proceeded even
with "dpm=0".
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Currently the allocation of config may fail and a null pointer
dereference on config can occur.  Fix this by added a null
check on a failed allocation of config.

Addresses-Coverity: ("Dereference null return")
Fixes: c2cd9d04 ("drm/amd/display: Hook up calls to do stereo mux and dig programming to stereo control interface")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Instead of using to_pci_dev + pci_get_drvdata,
use dev_get_drvdata to make code simpler.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Instead of using to_pci_dev + pci_get_drvdata,
use dev_get_drvdata to make code simpler.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Instead of using to_pci_dev + pci_get_drvdata,
use dev_get_drvdata to make code simpler.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

arch/x86/Makefile disables SSE and SSE2 for the whole kernel.  The
AMDGPU drivers modified in this patch re-enable SSE but not SSE2.  Turn
on SSE2 to support emitting double precision floating point instructions
rather than calls to non-existent (usually available from gcc_s or
compiler_rt) floating point helper routines for Clang.

This was originally landed in:
commit 10117450 ("drm/amd/display: add -msse2 to prevent Clang from emitting libcalls to undefined SW FP routines")
but reverted in:
commit 193392ed ("Revert "drm/amd/display: add -msse2 to prevent Clang from emitting libcalls to undefined SW FP routines"")
due to bugreports from GCC builds. Add guards to only do so for Clang.

Link: https://bugs.freedesktop.org/show_bug.cgi?id=109487
Link: https://github.com/ClangBuiltLinux/linux/issues/327Suggested-by: Sedat Dilek <sedat.dilek@gmail.com>
Suggested-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This was missed during the addition of VegaM support
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Kent Russell <kent.russell@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

1. the thermal temperature is asic related data, move the code logic to
xxx_ppt.c.
2. replace data structure PP_TemperatureRange with
smu_temperature_range.
3. change temperature uint from temp*1000 to temp (temperature uint).
Signed-off-by: Kevin Wang <kevin1.wang@amd.com>
Signed-off-by: Kenneth Feng <kenneth.feng@amd.com>
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

On vega20, there is an SMU message to query it.  On navi, it's fetched
from the metrics table.
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Otherwise, it will cause driver access non-existing sdma registers
in gpu reset code path
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Le Ma <Le.Ma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>