Add support for PIL loading of WPSS processor for SC7280
- WPSS boot will be requested by the wifi driver and hence
  disable auto-boot for WPSS.
- Add a separate shutdown sequence handler for WPSS.
- Add multiple power-domain voting support
- Parse firmware-name from dtsi entry
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1643712724-12436-4-git-send-email-quic_mpubbise@quicinc.com

Add WPSS PIL loading support for SC7280 SoCs.
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1643712724-12436-3-git-send-email-quic_mpubbise@quicinc.com

Convert Qualcomm ADSP/CDSP Remoteproc devicetree
binding to YAML.
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1643712724-12436-2-git-send-email-quic_mpubbise@quicinc.com

Add support to the K3 DSP remoteproc driver to configure all the C66x
and C71x cores on J721E SoCs to be either in IPC-only mode or the
traditional remoteproc mode. The IPC-only mode expects that the remote
processors are already booted by the bootloader, and only perform the
minimum steps required to initialize and deinitialize the virtio IPC
transports. The remoteproc mode allows the kernel remoteproc driver to
do the regular load and boot and other device management operations for
a DSP.

The IPC-only mode for a DSP is detected and configured at driver probe
time by querying the System Firmware for the DSP power and reset state
and/or status and making sure that the DSP is indeed started by the
bootloaders, otherwise the device is configured for remoteproc mode.

Support for IPC-only mode is achieved through .attach(), .detach() and
.get_loaded_rsc_table() callback ops and zeroing out the regular rproc
ops .prepare(), .unprepare(), .start() and .stop(). The resource table
follows a design-by-contract approach and is expected to be at the base
of the DDR firmware region reserved for each remoteproc, it is mostly
expected to contain only the virtio device and trace resource entries.

NOTE:
The driver cannot configure a DSP core for remoteproc mode by any
means without rebooting the kernel if that DSP core has been started
by a bootloader.  This is the current desired behavior and can be
enhanced in the future if the feature is needed.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220213201246.25952-6-s-anna@ti.com

Refactor out the mailbox request and associated ping logic code
from k3_dsp_rproc_start() function into its own separate function
so that it can be re-used in the soon to be added .attach() ops
callback.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220213201246.25952-5-s-anna@ti.com

Add support to the K3 R5F remoteproc driver to configure all the R5F
cores to be either in IPC-only mode or the traditional remoteproc mode.
The IPC-only mode expects that the remote processors are already booted
by the bootloader, and only performs the minimum steps required to
initialize and deinitialize the virtio IPC transports. The remoteproc
mode allows the kernel remoteproc driver to do the regular load and
boot and other device management operations for a R5F core.

The IPC-only mode for a R5F core is detected and configured at driver
probe time by querying the System Firmware for the R5F power and reset
state and/or status and making sure that the R5F core is indeed started
by the bootloaders, otherwise the device is configured for remoteproc
mode.

Support for IPC-only mode is achieved through .attach(), .detach() and
.get_loaded_rsc_table() callback ops and zeroing out the regular rproc
ops .prepare(), .unprepare(), .start() and .stop(). The resource table
follows a design-by-contract approach and is expected to be at the base
of the DDR firmware region reserved for each remoteproc, it is mostly
expected to contain only the virtio device and trace resource entries.

NOTE:
The driver cannot configure a R5F core for remoteproc mode by any
means without rebooting the kernel if that R5F core has been started
by a bootloader. This is the current desired behavior and can be
enhanced in the future if the feature is needed.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220213201246.25952-4-s-anna@ti.com

Refactor out the mailbox request and associated ping logic code
from k3_r5_rproc_start() function into its own separate function
so that it can be re-used in the soon to be added .attach() ops
callback.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220213201246.25952-3-s-anna@ti.com

The rproc_shutdown() function is currently not returning any
error code, and any failures within rproc_stop() are not passed
back to the users. Change the signature to return a success value
back to the callers.

The remoteproc sysfs and cdev interfaces are also updated to
return back this status to userspace.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220213201246.25952-2-s-anna@ti.com

Many remoteproc instances requires that Linux casts a proxy vote for an
interconnect path during boot, until they can do it themselves. Add
support for voting for a single path.

As this is a shared problem between both PAS and MSS drivers, the path
is acquired and votes casted from the common helper code.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Georgi Djakov <djakov@kernel.org>
Link: https://lore.kernel.org/r/20220225033224.2238425-1-bjorn.andersson@linaro.org

Add SCP support for mt8186
Signed-off-by: Allen-KH Cheng <Allen-KH.Cheng@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220225132747.31808-3-allen-kh.cheng@mediatek.com

Add mt8186 compatible to binding document.
Signed-off-by: Allen-KH Cheng <Allen-KH.Cheng@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220225132747.31808-2-allen-kh.cheng@mediatek.com

The device_node pointer is returned by of_parse_phandle() or
of_get_child_by_name() with refcount incremented.
We should use of_node_put() on it when done.

This function only call of_node_put(node) when of_address_to_resource
succeeds, missing error cases.

Fixes: 278d744c ("remoteproc: qcom: Fix potential device node leaks")
Fixes: 051fb70f ("remoteproc: qcom: Driver for the self-authenticating Hexagon v5")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220308064522.13804-1-linmq006@gmail.com

The device_node pointer is returned by of_parse_phandle()  with refcount
incremented. We should use of_node_put() on it when done.

Fixes: aed361ad ("remoteproc: qcom: Introduce WCNSS peripheral image loader")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220308063102.10049-1-linmq006@gmail.com

The device_node pointer is returned by of_parse_phandle()  with refcount
incremented. We should use of_node_put() on it when done.

Fixes: dc160e44 ("remoteproc: qcom: Introduce Non-PAS ADSP PIL driver")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220308031219.4718-1-linmq006@gmail.com

The rproc_da_to_va() API is an exported function, so move its
declaration from the remoteproc local remoteproc_internal.h
to the public remoteproc.h file.

This will allow drivers outside of the remoteproc folder to be
able to use this API.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
[adjusted line numbers to apply]
Signed-off-by: Drew Fustini <dfustini@baylibre.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220308172515.29556-1-dfustini@baylibre.com

The Wakeup M3 remote processor is controlled by the wkup_m3_ipc
client driver, so set the newly introduced 'sysfs_read_only' flag
to not allow any overriding of the remoteproc firmware, state,
recovery, or coredump from userspace.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Puranjay Mohan <p-mohan@ti.com>
Link: https://lore.kernel.org/r/20220216081224.9956-3-p-mohan@ti.comSigned-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>

The remoteproc framework provides sysfs interfaces for changing
the firmware name and for starting/stopping a remote processor
through the sysfs files 'state' and 'firmware'. The 'coredump'
file is used to set the coredump configuration. The 'recovery'
sysfs file can also be used similarly to control the error recovery
state machine of a remoteproc. These interfaces are currently
allowed irrespective of how the remoteprocs were booted (like
remoteproc self auto-boot, remoteproc client-driven boot etc).
These interfaces can adversely affect a remoteproc and its clients
especially when a remoteproc is being controlled by a remoteproc
client driver(s). Also, not all remoteproc drivers may want to
support the sysfs interfaces by default.

Add support to make the remoteproc sysfs files read only by
introducing a state flag 'sysfs_read_only' that the individual
remoteproc drivers can set based on their usage needs. The default
behavior is to allow the sysfs operations as before.

Implement attribute_group->is_visible() to make the sysfs
entries read only when 'sysfs_read_only' flag is set.
Signed-off-by: Puranjay Mohan <p-mohan@ti.com>
Link: https://lore.kernel.org/r/20220216081224.9956-2-p-mohan@ti.comSigned-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>

Check count for 0, to avoid a potential underflow. Make the check the
same as the one in rproc_recovery_write().

Fixes: 3afdc59e ("remoteproc: Add coredump debugfs entry")
Signed-off-by: Alistair Delva <adelva@google.com>
Cc: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Cc: stable@vger.kernel.org
Cc: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Sibi Sankar <sibis@codeaurora.org>
Cc: linux-remoteproc@vger.kernel.org
Cc: kernel-team@android.com
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220119232139.1125908-1-adelva@google.com

Simplify the probe function, where possible, by using dev_err_probe().
While at it, as to increase human readability, also remove some
unnecessary forced void pointer casts that were previously used in
error checking.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220124120915.41292-3-angelogioacchino.delregno@collabora.comSigned-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>

Cleanup the scp_probe() function by reordering some calls in this
function, useful to reduce the usage of goto(s), and preparing
for one more usage of dev_err_probe().

In particular, we can get the clocks before mapping the memory region,
and move the mutexes initialization right before registering the ipi
handler (which is the first mutex user in this driver).
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220124120915.41292-2-angelogioacchino.delregno@collabora.comSigned-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>

To simplify the probe function, switch from using rproc_alloc() to
devm_rproc_alloc(); while at it, also put everything on a single line,
as it acceptably fits in 82 columns.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220124120915.41292-1-angelogioacchino.delregno@collabora.comSigned-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>

Pull irq fixes from Borislav Petkov:

 - Drop an unused private data field in the AIC driver

 - Various fixes to the realtek-rtl driver

 - Make the GICv3 ITS driver compile again in !SMP configurations

 - Force reset of the GICv3 ITSs at probe time to avoid issues during kexec

 - Yet another kfree/bitmap_free conversion

 - Various DT updates (Renesas, SiFive)

* tag 'irq_urgent_for_v5.17_rc2_p2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  dt-bindings: interrupt-controller: sifive,plic: Group interrupt tuples
  dt-bindings: interrupt-controller: sifive,plic: Fix number of interrupts
  dt-bindings: irqchip: renesas-irqc: Add R-Car V3U support
  irqchip/gic-v3-its: Reset each ITS's BASERn register before probe
  irqchip/gic-v3-its: Fix build for !SMP
  irqchip/loongson-pch-ms: Use bitmap_free() to free bitmap
  irqchip/realtek-rtl: Service all pending interrupts
  irqchip/realtek-rtl: Fix off-by-one in routing
  irqchip/realtek-rtl: Map control data to virq
  irqchip/apple-aic: Drop unused ipi_hwirq field

Pull perf fixes from Borislav Petkov:

 - Prevent accesses to the per-CPU cgroup context list from another CPU
   except the one it belongs to, to avoid list corruption

 - Make sure parent events are always woken up to avoid indefinite hangs
   in the traced workload

* tag 'perf_urgent_for_v5.17_rc2_p2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/core: Fix cgroup event list management
  perf: Always wake the parent event

Pull scheduler fix from Borislav Petkov:
 "Make sure the membarrier-rseq fence commands are part of the reported
  set when querying membarrier(2) commands through MEMBARRIER_CMD_QUERY"

* tag 'sched_urgent_for_v5.17_rc2_p2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/membarrier: Fix membarrier-rseq fence command missing from query bitmask

Pull x86 fixes from Borislav Petkov:

 - Add another Intel CPU model to the list of CPUs supporting the
   processor inventory unique number

 - Allow writing to MCE thresholding sysfs files again - a previous
   change had accidentally disabled it and no one noticed. Goes to show
   how much is this stuff used

* tag 'x86_urgent_for_v5.17_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/cpu: Add Xeon Icelake-D to list of CPUs that support PPIN
  x86/MCE/AMD: Allow thresholding interface updates after init

Merge misc fixes from Andrew Morton:
 "12 patches.

  Subsystems affected by this patch series: sysctl, binfmt, ia64, mm
  (memory-failure, folios, kasan, and psi), selftests, and ocfs2"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  ocfs2: fix a deadlock when commit trans
  jbd2: export jbd2_journal_[grab|put]_journal_head
  psi: fix "defined but not used" warnings when CONFIG_PROC_FS=n
  psi: fix "no previous prototype" warnings when CONFIG_CGROUPS=n
  mm, kasan: use compare-exchange operation to set KASAN page tag
  kasan: test: fix compatibility with FORTIFY_SOURCE
  tools/testing/scatterlist: add missing defines
  mm: page->mapping folio->mapping should have the same offset
  memory-failure: fetch compound_head after pgmap_pfn_valid()
  ia64: make IA64_MCA_RECOVERY bool instead of tristate
  binfmt_misc: fix crash when load/unload module
  include/linux/sysctl.h: fix register_sysctl_mount_point() return type

commit 6f1b2285 introduces a regression which can deadlock as
follows:

  Task1:                              Task2:
  jbd2_journal_commit_transaction     ocfs2_test_bg_bit_allocatable
  spin_lock(&jh->b_state_lock)        jbd_lock_bh_journal_head
  __jbd2_journal_remove_checkpoint    spin_lock(&jh->b_state_lock)
  jbd2_journal_put_journal_head
  jbd_lock_bh_journal_head

Task1 and Task2 lock bh->b_state and jh->b_state_lock in different
order, which finally result in a deadlock.

So use jbd2_journal_[grab|put]_journal_head instead in
ocfs2_test_bg_bit_allocatable() to fix it.

Link: https://lkml.kernel.org/r/20220121071205.100648-3-joseph.qi@linux.alibaba.com
Fixes: 6f1b2285 ("ocfs2: fix race between searching chunks and release journal_head from buffer_head")
Signed-off-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Reported-by: Gautham Ananthakrishna <gautham.ananthakrishna@oracle.com>
Tested-by: Gautham Ananthakrishna <gautham.ananthakrishna@oracle.com>
Reported-by: Saeed Mirzamohammadi <saeed.mirzamohammadi@oracle.com>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: Andreas Dilger <adilger.kernel@dilger.ca>
Cc: Changwei Ge <gechangwei@live.cn>
Cc: Gang He <ghe@suse.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Jun Piao <piaojun@huawei.com>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Patch series "ocfs2: fix a deadlock case".

This fixes a deadlock case in ocfs2.  We firstly export jbd2 symbols
jbd2_journal_[grab|put]_journal_head as preparation and later use them
in ocfs2 insread of jbd_[lock|unlock]_bh_journal_head to fix the
deadlock.

This patch (of 2):

This exports symbols jbd2_journal_[grab|put]_journal_head, which will be
used outside modules, e.g.  ocfs2.

Link: https://lkml.kernel.org/r/20220121071205.100648-2-joseph.qi@linux.alibaba.comSigned-off-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Changwei Ge <gechangwei@live.cn>
Cc: Gang He <ghe@suse.com>
Cc: Jun Piao <piaojun@huawei.com>
Cc: Andreas Dilger <adilger.kernel@dilger.ca>
Cc: Gautham Ananthakrishna <gautham.ananthakrishna@oracle.com>
Cc: Saeed Mirzamohammadi <saeed.mirzamohammadi@oracle.com>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

When CONFIG_PROC_FS is disabled psi code generates the following
warnings:

  kernel/sched/psi.c:1364:30: warning: 'psi_cpu_proc_ops' defined but not used [-Wunused-const-variable=]
      1364 | static const struct proc_ops psi_cpu_proc_ops = {
           |                              ^~~~~~~~~~~~~~~~
  kernel/sched/psi.c:1355:30: warning: 'psi_memory_proc_ops' defined but not used [-Wunused-const-variable=]
      1355 | static const struct proc_ops psi_memory_proc_ops = {
           |                              ^~~~~~~~~~~~~~~~~~~
  kernel/sched/psi.c:1346:30: warning: 'psi_io_proc_ops' defined but not used [-Wunused-const-variable=]
      1346 | static const struct proc_ops psi_io_proc_ops = {
           |                              ^~~~~~~~~~~~~~~

Make definitions of these structures and related functions conditional
on CONFIG_PROC_FS config.

Link: https://lkml.kernel.org/r/20220119223940.787748-3-surenb@google.com
Fixes: 0e94682b ("psi: introduce psi monitor")
Signed-off-by: Suren Baghdasaryan <surenb@google.com>
Reported-by: kernel test robot <lkp@intel.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

When CONFIG_CGROUPS is disabled psi code generates the following
warnings:

  kernel/sched/psi.c:1112:21: warning: no previous prototype for 'psi_trigger_create' [-Wmissing-prototypes]
      1112 | struct psi_trigger *psi_trigger_create(struct psi_group *group,
           |                     ^~~~~~~~~~~~~~~~~~
  kernel/sched/psi.c:1182:6: warning: no previous prototype for 'psi_trigger_destroy' [-Wmissing-prototypes]
      1182 | void psi_trigger_destroy(struct psi_trigger *t)
           |      ^~~~~~~~~~~~~~~~~~~
  kernel/sched/psi.c:1249:10: warning: no previous prototype for 'psi_trigger_poll' [-Wmissing-prototypes]
      1249 | __poll_t psi_trigger_poll(void **trigger_ptr,
           |          ^~~~~~~~~~~~~~~~

Change the declarations of these functions in the header to provide the
prototypes even when they are unused.

Link: https://lkml.kernel.org/r/20220119223940.787748-2-surenb@google.com
Fixes: 0e94682b ("psi: introduce psi monitor")
Signed-off-by: Suren Baghdasaryan <surenb@google.com>
Reported-by: kernel test robot <lkp@intel.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

It has been reported that the tag setting operation on newly-allocated
pages can cause the page flags to be corrupted when performed
concurrently with other flag updates as a result of the use of
non-atomic operations.

Fix the problem by using a compare-exchange loop to update the tag.

Link: https://lkml.kernel.org/r/20220120020148.1632253-1-pcc@google.com
Link: https://linux-review.googlesource.com/id/I456b24a2b9067d93968d43b4bb3351c0cec63101
Fixes: 2813b9c0 ("kasan, mm, arm64: tag non slab memory allocated via pagealloc")
Signed-off-by: Peter Collingbourne <pcc@google.com>
Reviewed-by: Andrey Konovalov <andreyknvl@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

With CONFIG_FORTIFY_SOURCE enabled, string functions will also perform
dynamic checks using __builtin_object_size(ptr), which when failed will
panic the kernel.

Because the KASAN test deliberately performs out-of-bounds operations,
the kernel panics with FORTIFY_SOURCE, for example:

 | kernel BUG at lib/string_helpers.c:910!
 | invalid opcode: 0000 [#1] PREEMPT SMP KASAN PTI
 | CPU: 1 PID: 137 Comm: kunit_try_catch Tainted: G    B             5.16.0-rc3+ #3
 | Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-2 04/01/2014
 | RIP: 0010:fortify_panic+0x19/0x1b
 | ...
 | Call Trace:
 |  kmalloc_oob_in_memset.cold+0x16/0x16
 |  ...

Fix it by also hiding `ptr` from the optimizer, which will ensure that
__builtin_object_size() does not return a valid size, preventing
fortified string functions from panicking.

Link: https://lkml.kernel.org/r/20220124160744.1244685-1-elver@google.comSigned-off-by: Marco Elver <elver@google.com>
Reported-by: Nico Pache <npache@redhat.com>
Reviewed-by: Nico Pache <npache@redhat.com>
Reviewed-by: Andrey Konovalov <andreyknvl@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The cited commits replaced preemptible with pagefault_disabled and
flush_kernel_dcache_page with flush_dcache_page respectively, hence need
to update the corresponding defines in the test.

  scatterlist.c: In function ‘sg_miter_stop’:
  scatterlist.c:919:4: warning: implicit declaration of function ‘flush_dcache_page’ [-Wimplicit-function-declaration]
      flush_dcache_page(miter->page);
      ^~~~~~~~~~~~~~~~~
  In file included from linux/scatterlist.h:8:0,
                   from scatterlist.c:9:
  scatterlist.c:922:18: warning: implicit declaration of function ‘pagefault_disabled’ [-Wimplicit-function-declaration]
      WARN_ON_ONCE(!pagefault_disabled());
                    ^
  linux/mm.h:23:25: note: in definition of macro ‘WARN_ON_ONCE’
    int __ret_warn_on = !!(condition);                      \
                           ^~~~~~~~~

Link: https://lkml.kernel.org/r/20220118082105.1737320-1-maorg@nvidia.com
Fixes: 723aca20 ("mm/scatterlist: replace the !preemptible warning in sg_miter_stop()")
Fixes: 0e84f5db ("scatterlist: replace flush_kernel_dcache_page with flush_dcache_page")
Signed-off-by: Maor Gottlieb <maorg@nvidia.com>
Tested-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

As with the other members of folio, the offset of page->mapping and
folio->mapping must be the same.  The compile-time check was
inadvertently removed during development.  Add it back.

[willy@infradead.org: changelog redo]

Link: https://lkml.kernel.org/r/20220104011734.21714-1-richard.weiyang@gmail.comSigned-off-by: Wei Yang <richard.weiyang@gmail.com>
Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

memory_failure_dev_pagemap() at the moment assumes base pages (e.g.
dax_lock_page()).  For devmap with compound pages fetch the
compound_head in case a tail page memory failure is being handled.

Currently this is a nop, but in the advent of compound pages in
dev_pagemap it allows memory_failure_dev_pagemap() to keep working.

Without this fix memory-failure handling (i.e.  MCEs on pmem) with
device-dax configured namespaces will regress (and crash).

Link: https://lkml.kernel.org/r/20211202204422.26777-2-joao.m.martins@oracle.comReported-by: Jane Chu <jane.chu@oracle.com>
Signed-off-by: Joao Martins <joao.m.martins@oracle.com>
Reviewed-by: Naoya Horiguchi <naoya.horiguchi@nec.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Muchun Song <songmuchun@bytedance.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

In linux-next, IA64_MCA_RECOVERY uses the (new) function
make_task_dead(), which is not exported for use by modules.  Instead of
exporting it for one user, convert IA64_MCA_RECOVERY to be a bool
Kconfig symbol.

In a config file from "kernel test robot <lkp@intel.com>" for a
different problem, this linker error was exposed when
CONFIG_IA64_MCA_RECOVERY=m.

Fixes this build error:

  ERROR: modpost: "make_task_dead" [arch/ia64/kernel/mca_recovery.ko] undefined!

Link: https://lkml.kernel.org/r/20220124213129.29306-1-rdunlap@infradead.org
Fixes: 0e25498f ("exit: Add and use make_task_dead.")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Suggested-by: Christoph Hellwig <hch@infradead.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

We should unregister the table upon module unload otherwise something
horrible will happen when we load binfmt_misc module again.  Also note
that we should keep value returned by register_sysctl_mount_point() and
release it later, otherwise it will leak.

Also, per Christian's comment, to fully restore the old behavior that
won't break userspace the check(binfmt_misc_header) should be
eliminated.

To reproduce:
  modprobe binfmt_misc
  modprobe -r binfmt_misc
  modprobe binfmt_misc
  modprobe -r binfmt_misc
  modprobe binfmt_misc

resulting in

  modprobe: can't load module binfmt_misc (kernel/fs/binfmt_misc.ko): Cannot allocate memory

and an unhappy kernel:

  binfmt_misc: Failed to create fs/binfmt_misc sysctl mount point
  binfmt_misc: Failed to create fs/binfmt_misc sysctl mount point
  BUG: unable to handle page fault for address: fffffbfff8004802
  Call Trace:
    init_misc_binfmt+0x2d/0x1000 [binfmt_misc]

Link: https://lkml.kernel.org/r/20220124181812.1869535-2-ztong0001@gmail.com
Fixes: 3ba442d5 ("fs: move binfmt_misc sysctl to its own file")
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Co-developed-by: Christian Brauner<brauner@kernel.org>
Acked-by: Luis Chamberlain <mcgrof@kernel.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Iurii Zaikin <yzaikin@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The CONFIG_SYSCTL=n stub returns the wrong type.

Fixes: ee9efac4 ("sysctl: add helper to register a sysctl mount point")
Reported-by: kernel test robot <lkp@intel.com>
Acked-by: Luis Chamberlain <mcgrof@kernel.org>
Cc: Tong Zhang <ztong0001@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge tag 'irqchip-fixes-5.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent

Pull irqchip fixes from Marc Zyngier:

  - Drop an unused private data field in the AIC driver

  - Various fixes to the realtek-rtl driver

  - Make the GICv3 ITS driver compile again in !SMP configurations

  - Force reset of the GICv3 ITSs at probe time to avoid issues during kexec

  - Yet another kfree/bitmap_free conversion

  - Various DT updates (Renesas, SiFive)

Link: https://lore.kernel.org/r/20220128174217.517041-1-maz@kernel.org