The third output on WM5110 is a general purpose headphone output which can
be used to drive an earpice rather than a dedicated earpiece driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Some devices support additional clock rates.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The interrupt handler uses the chip state.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

We will fail to probe without one.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

We never set the GPIO from atomic context so there's no reason why we
can't support a GPIO that needs to sleep when configuring.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Allow regulators managed via DAPM to make use of the bypass support that
has recently been added to the regulator API by setting a flag
SND_SOC_DAPM_REGULATOR_BYPASS. When this flag is set the regulator will
be put into bypass mode before being disabled, allowing the regulator to
fall into bypass mode if it can't be disabled due to other users.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

regulator: Bypass mode support

Allow regulators to be put into a non-regulating mode bypassing the
input straight to the output, mostly used by low power retention modes.

According to cs4270 datasheet, there is no reference to mono mode.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Linux 3.6-rc6 has all our bug fixes.

Conflicts (trivial overlap):
	sound/soc/omap/am3517evm.c

When the kernel has been booted with DT blob the platform data is NULL for
the driver.
We need to construct the pdata based on the DT information for runtime use.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Access the pdata via a pointer within the twl4030_priv structure.
In preparation for DeviceTree support.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Allocate the private data with devm_kzalloc.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

We no longer have users for the set_hs_extmute callback which has been
replaced by hs_extmute_gpio so the codec driver can handle the external
mute if it is needed by the board.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Remove the use of set_hs_extmute callback and let the codec driver to
handle the extmute GPIO.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The external mute (if it is in use) is handled by a GPIO line. Prepare to
remove the set_hs_extmute callback and replace it with:
hs_extmute_gpio: the GPIO number to use for external mute

When the users of set_hs_extmute has been converted the callback can be removed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Add support when the kernel has been booted with DT blob. In this case the
pdata is NULL, we need to reach up to the core node and check if the codec
part has been enabled to determine if we need to coexist with the codec or
not.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Support for loading the twl4030 audio module via devicetree.
Sub devices for codec and vibra will be created as mfd devices once the
core MFD driver is loaded when the kernel is booted with a DT blob.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This commit adds an empty of_find_node_by_name() function for !CONFIG_OF
builds.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

twl-core has API to get the boot time configured HFCLK rate which has the
same rate as the audio MCLK.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

CFG_BOOT register's HFCLK_FREQ field hold information about the used HFCLK
frequency.
Add possibility for users to get the configured rate based on this
register.
This register was configured during boot, without it the chip would not
operate correctly, so we can trust on this information.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

To facilitate the device tree support the probe function need to be rearanged.
Small cleanup in the APLL frequency selection part as well.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

To clean up the module probe and remove functions.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Place the MODULE_* lines in the same block and add MODULE_DESCRIPTION.
Rearange the platform_driver structure at the same time.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Original author: Russell King <rmk+kernel@arm.linux.org.uk>

Switch the omap-pcm to use dmaengine.
Certain features are not supported by after dmaengine conversion:
1. No period wakeup mode
   DMA engine has no way to communicate this information through
   standard channels.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Set the dma_data for the stream (snd_soc_dai_set_dma_data) at dai_startup
time so omap-pcm will have access to the needed information regarding to
the DMA channel earlier.
This is needed for the clean dmaengine support.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Instead of the OMAP DMA data type definition the data_type will be used to
specify the number of bits the DMA word should be configured or 0 in case
when based on the stream's format the omap-pcm can decide the needed DMA
word size.
This feature is needed for the omap-hdmi where the sDMA need to be
configured for 32bit word type regardless of the audio format used.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

omap-pcm can figure out the correct dma_type based on the stream's format.
In this way we can get rid of the plat/dma.h include from these drivers.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Get the needed resources in a correct way and avoid using defines for them.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

To help the driver to get the correct memory range to access McPDM
registers.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Based on the format of the stream the omap-pcm can decide alone what data
type should be used with by the sDMA.
Keep the possibility for OMAP dai drivers to tell omap-pcm if they want to
use different data type. This is needed for the omap-hdmi for example which
needs 32bit data type even if the stream format is S16_LE.

The check if (dma_data->data_type) is safe at the moment since omap-pcm
does not support 8bit samples (OMAP_DMA_DATA_TYPE_S8 == 0x00).

The next step is to redefine the meaning of dma_data->data_type to unblock
this limitation.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The omap-pcm platform driver no longer needs this parameter to select
between ELEMENT and PACKET mode. The selection is based on the configured
packet_size.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Since we only have element or packet synchronization we can use the
dma_data->packet_size to select the desired mode:
if packet_size is 0 we use ELEMENT mode
if packet_size is not 0 we use PACKET mode for sDMA synchronization.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

When McBSP is configured in threshold mode we can use sDMA packet mode in
all cases.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

When requested (DMA_PREP_INTERRUPT is cleared in flags) disable all DMA
interrupts for the channel. In this mode user space does not expect
periodic reports from kernel about the progress of the audio stream.
PulseAudio for example support this type of mode.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>