- 04 Aug, 2024 3 commits
-
-
David S. Miller authored
Lorenzo Bianconi says: ==================== Add second QDMA support for EN7581 eth controller EN7581 SoC supports two independent QDMA controllers to connect the Ethernet Frame Engine (FE) to the CPU. Introduce support for the second QDMA controller. This is a preliminary series to support multiple FE ports (e.g. connected to a second PHY controller). Changes since v1: - squash patch 6/9 and 7/9 - move some duplicated code from patch 2/9 in 1/9 - cosmetics ==================== Signed-off-by:David S. Miller <davem@davemloft.net>
-
Lorenzo Bianconi authored
Introduce support for the DSA built-in switch available on the EN7581 development board. EN7581 support is similar to MT7988 one except it requires to set MT7530_FORCE_MODE bit in MT753X_PMCR_P register for on cpu port. Tested-by:
Benjamin Larsson <benjamin.larsson@genexis.eu> Signed-off-by:
Lorenzo Bianconi <lorenzo@kernel.org> Reviewed-by:
Arınç ÜNAL <arinc.unal@arinc9.com> Reviewed-by:
Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by:
-
Lorenzo Bianconi authored
Add documentation for the built-in switch which can be found in the Airoha EN7581 SoC. Signed-off-by:
-
- 03 Aug, 2024 12 commits
-
-
David S. Miller authored
Kuniyuki Iwashima says: ==================== net: Random cleanup for netns initialisation. patch 1 & 2 suppress unwanted memory allocation for net->gen->ptr[]. patch 3 ~ 6 move part of netns initialisation to prenet_init() that do not require pernet_ops_rwsem. v2: patch 1 : Removed Fixes: tag patch 2 : Use XOR for WARN_ON() v1: https://lore.kernel.org/netdev/20240729210801.16196-1-kuniyu@amazon.com/ ==================== Signed-off-by:
-
Kuniyuki Iwashima authored
Commit 7c3f1875 ("net: move somaxconn init from sysctl code") introduced net_defaults_ops to make sure that net.core sysctl knobs are always initialised even if CONFIG_SYSCTL is disabled. Such operations better fit preinit_net() added for a similar purpose by commit 6e77a5a4 ("net: initialize net->notrefcnt_tracker earlier"). Let's initialise the sysctl defaults in preinit_net(). Signed-off-by:
Kuniyuki Iwashima <kuniyu@amazon.com> Signed-off-by:
-
Kuniyuki Iwashima authored
Most initialisations in setup_net() do not require pernet_ops_rwsem and can be moved to preinit_net(). Signed-off-by:
-
Kuniyuki Iwashima authored
When initialising the root netns, we call preinit_net() under pernet_ops_rwsem. However, the operations in preinit_net() do not require pernet_ops_rwsem. Also, we don't hold it for preinit_net() when initialising non-root netns. To be consistent, let's call preinit_net() without pernet_ops_rwsem in net_ns_init(). Signed-off-by:
-
Kuniyuki Iwashima authored
When initialising the root netns, we set net->passive in setup_net(). However, we do it twice for non-root netns in copy_net_ns() and setup_net(). This is because we could bypass setup_net() in copy_net_ns() if down_read_killable() fails. preinit_net() is a better place to put such an operation. Let's initialise net->passive in preinit_net(). Signed-off-by:
-
Kuniyuki Iwashima authored
We can allocate per-netns memory for struct pernet_operations by specifying id and size. register_pernet_operations() assigns an id to pernet_operations and later ops_init() allocates the specified size of memory as net->gen->ptr[id]. If id is missing, no memory is allocated. If size is not specified, pernet_operations just wastes an entry of net->gen->ptr[] for every netns. net_generic is available only when both id and size are specified, so let's ensure that. While we are at it, we add const to both fields. Signed-off-by:
-
Kuniyuki Iwashima authored
Commit fd558d18 ("l2tp: Split pppol2tp patch into separate l2tp and ppp parts") converted net->gen->ptr[pppol2tp_net_id] in l2tp_ppp.c to net->gen->ptr[l2tp_net_id] in l2tp_core.c. Now the leftover wastes one entry of net->gen->ptr[] in each netns. Let's avoid the unwanted allocation. Signed-off-by:
Simon Horman <horms@kernel.org> Reviewed-by:
James Chapman <jchapman@katalix.com> Signed-off-by:
-
Kyle Swenson authored
The DEVID register contains two pieces of information: the device ID in the upper nibble, and the silicon revision number in the lower nibble. The driver should work fine with any silicon revision, so let's mask that out in the device ID check. Fixes: 20e6d190 ("net: pse-pd: Add TI TPS23881 PSE controller driver") Signed-off-by:
Kyle Swenson <kyle.swenson@est.tech> Reviewed-by:
Thomas Petazzoni <thomas.petazzoni@bootlin.com> Acked-by:
Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by:
-
Pawel Dembicki authored
According to the datasheet, the VSC73xx family's maximum internal MDIO bus speed is 20 MHz. It also allows disabling the preamble. This commit sets the MDIO clock prescaler to the minimum value and disables the preamble to speed up MDIO operations. It doesn't affect the external bus because it's configured in a different subblock. Signed-off-by:
Pawel Dembicki <paweldembicki@gmail.com> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Link: https://patch.msgid.link/20240731203455.580262-1-paweldembicki@gmail.comSigned-off-by:
Jakub Kicinski <kuba@kernel.org>
-
Yue Haibing authored
commit 3cec055c ("rxrpc: Don't hold a ref for connection workqueue") left behind rxrpc_put_client_conn(). And commit 248f219c ("rxrpc: Rewrite the data and ack handling code") removed rxrpc_accept_incoming_calls() but left declaration. Signed-off-by:
Yue Haibing <yuehaibing@huawei.com> Reviewed-by:
-
Dmitry Antipov authored
According to '__reuseport_alloc()', annotate flexible array member 'sock' of 'struct sock_reuseport' with '__counted_by()' and use convenient 'struct_size()' to simplify the math used in 'kzalloc()'. Signed-off-by:
Dmitry Antipov <dmantipov@yandex.ru> Reviewed-by:
Gustavo A. R. Silva <gustavoars@kernel.org> Reviewed-by:
-
Simon Horman authored
Smatch reports that copying media_name and if_name to name_parts may overwrite the destination. .../bearer.c:166 bearer_name_validate() error: strcpy() 'media_name' too large for 'name_parts->media_name' (32 vs 16) .../bearer.c:167 bearer_name_validate() error: strcpy() 'if_name' too large for 'name_parts->if_name' (1010102 vs 16) This does seem to be the case so guard against this possibility by using strscpy() and failing if truncation occurs. Introduced by commit b97bf3fd ("[TIPC] Initial merge") Compile tested only. Reviewed-by:
-
- 02 Aug, 2024 25 commits
-
-
Jakub Kicinski authored
Nick Child says: ==================== ibmveth RR performance This patchset aims to increase the ibmveth drivers small packet request response rate. These 2 patches address: 1. NAPI rescheduling technique 2. Driver-side processing of small packets Testing over several netperf tcp_rr connections, we saw a 30% increase in transactions per second. No regressions were observed in other workloads. ==================== Link: https://patch.msgid.link/20240801211215.128101-1-nnac123@linux.ibm.comSigned-off-by:
-
Nick Child authored
When the length of a packet is under the rx_copybreak threshold, the buffer is copied into a new skb and sent up the stack. This allows the dma mapped memory to be recycled back to FW. Previously, the reuse of the DMA space was handled immediately. This means that further packet processing has to wait until h_add_logical_lan finishes for this packet. Therefore, when reusing a packet, offload the hcall to the replenish function. As a result, much of the shared logic between the recycle and replenish functions can be removed. This change increases TCP_RR packet rate by another 15% (370k to 430k txns). We can see the ftrace data supports this: PREV: ibmveth_poll = 8078553.0 us / 190999.0 hits = AVG 42.3 us NEW: ibmveth_poll = 7632787.0 us / 224060.0 hits = AVG 34.07 us Signed-off-by:
Nick Child <nnac123@linux.ibm.com> Reviewed-by:
Shannon Nelson <shannon.nelson@amd.com> Link: https://patch.msgid.link/20240801211215.128101-3-nnac123@linux.ibm.comSigned-off-by:
-
Nick Child authored
When the ibmveth driver processes less than the budget, it must call napi_complete_done() to release the instance. This function will return false if the driver should avoid rearming interrupts. Previously, the driver was ignoring the return code of napi_complete_done(). As a result, there were unnecessary calls to enable the veth irq. Therefore, use the return code napi_complete_done() to determine if irq rearm is necessary. Additionally, in the event that new data is received immediately after rearming interrupts, rather than just rescheduling napi, also jump back to the poll processing loop since we are already in the poll function (and know that we did not expense all of budget). This slight tweak results in a 15% increase in TCP_RR transaction rate (320k to 370k txns). We can see the ftrace data supports this: PREV: ibmveth_poll = 8818014.0 us / 182802.0 hits = AVG 48.24 NEW: ibmveth_poll = 8082398.0 us / 191413.0 hits = AVG 42.22 Signed-off-by:
-
Simon Horman authored
linkmode_andnot() simply returns the result of bitmap_andnot(). And the return type of bitmap_andnot() is bool. So it makes sense for the return type of linkmode_andnot() to also be bool. I checked all call-sites and they either ignore the return value or treat it as a bool. Compile tested only. Link: https://lore.kernel.org/netdev/68088998-4486-4930-90a4-96a32f08c490@lunn.ch/Signed-off-by:
-
Jakub Kicinski authored
Lorenzo Bianconi says: ==================== Add second QDMA support for EN7581 eth controller EN7581 SoC supports two independent QDMA controllers to connect the Ethernet Frame Engine (FE) to the CPU. Introduce support for the second QDMA controller. This is a preliminary series to support multiple FE ports (e.g. connected to a second PHY controller). ==================== Link: https://patch.msgid.link/cover.1722522582.git.lorenzo@kernel.orgSigned-off-by:
-
Lorenzo Bianconi authored
Link the running gdm port to the qdma controller used to connect with the CPU. Moreover, load all QDMA controllers available on EN7581 SoC. Signed-off-by:
-
Lorenzo Bianconi authored
This is a preliminary patch to support multi-QDMA controllers. Signed-off-by:
-
Lorenzo Bianconi authored
Map MMIO regions of both qdma controllers available on EN7581 SoC. Run airoha_hw_cleanup routine for both QDMA controllers available on EN7581 SoC removing airoha_eth module or in airoha_probe error path. This is a preliminary patch to support multi-QDMA controllers. Signed-off-by:
-
Lorenzo Bianconi authored
This is a preliminary patch to support multi-QDMA controllers. Signed-off-by:
-
Lorenzo Bianconi authored
Move airoha_eth pointer in airoha_qdma structure from airoha_tx_irq_queue/airoha_queue ones. This is a preliminary patch to introduce support for multi-QDMA controllers available on EN7581. Signed-off-by:
-
Lorenzo Bianconi authored
QDMA controllers have independent irq lines, so move irqmask in airoha_qdma structure. This is a preliminary patch to support multiple QDMA controllers. Signed-off-by:
-
Lorenzo Bianconi authored
QDMA controllers available in EN7581 SoC have independent tx/rx hw queues so move them in airoha_queues structure. Signed-off-by:
-
Lorenzo Bianconi authored
Introduce airoha_qdma struct and move qdma IO register mapping in airoha_qdma. This is a preliminary patch to enable both QDMA controllers available on EN7581 SoC. Signed-off-by:
-
Simon Horman authored
Build bot reports undefined references to devlink functions. And local testing revealed undefined references to page_pool functions. Based on a patch by Jakub Kicinski <kuba@kernel.org> Fixes: 1a9d4889 ("eth: fbnic: Allocate core device specific structures and devlink interface") Reported-by:
kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202408011219.hiPmwwAs-lkp@intel.com/Signed-off-by:
-
Jakub Kicinski authored
Print more stack frames and the failing line when check fails. This helps when tests use helpers to do the checks. Before: # At ./ksft/drivers/net/hw/rss_ctx.py line 92: # Check failed 1037698 >= 396893.0 traffic on other queues:[344612, 462380, 233020, 449174, 342298] not ok 8 rss_ctx.test_rss_context_queue_reconfigure After: # Check| At ./ksft/drivers/net/hw/rss_ctx.py, line 387, in test_rss_context_queue_reconfigure: # Check| test_rss_queue_reconfigure(cfg, main_ctx=False) # Check| At ./ksft/drivers/net/hw/rss_ctx.py, line 230, in test_rss_queue_reconfigure: # Check| _send_traffic_check(cfg, port, ctx_ref, { 'target': (0, 3), # Check| At ./ksft/drivers/net/hw/rss_ctx.py, line 92, in _send_traffic_check: # Check| ksft_lt(sum(cnts[i] for i in params['noise']), directed / 2, # Check failed 1045235 >= 405823.5 traffic on other queues (context 1)':[460068, 351995, 565970, 351579, 127270] not ok 8 rss_ctx.test_rss_context_queue_reconfigure Link: https://patch.msgid.link/20240801232317.545577-1-kuba@kernel.orgSigned-off-by: -
Stanislav Fomichev authored
Petr suggested to use errno.EOPNOTSUPP instead of hard-coded 95 in the new test case. Adjust existing ones to match this style. Signed-off-by:
Stanislav Fomichev <sdf@fomichev.me> Link: https://patch.msgid.link/20240802000309.2368-3-sdf@fomichev.meSigned-off-by:
-
Stanislav Fomichev authored
Add new @ksft_disruptive decorator to mark the tests that might be disruptive to the system. Depending on how well the previous test works in the CI we might want to disable disruptive tests by default and only let the developers run them manually. KSFT framework runs disruptive tests by default. DISRUPTIVE=False environment (or config file) can be used to disable these tests. ksft_setup should be called by the test cases that want to use new decorator (ksft_setup is only called via NetDrvEnv/NetDrvEpEnv for now). In the future we can add similar decorators to, for example, avoid running slow tests all the time. And/or have some option to run only 'fast' tests for some sort of smoke test scenario. $ DISRUPTIVE=False ./stats.py KTAP version 1 1..5 ok 1 stats.check_pause ok 2 stats.check_fec ok 3 stats.pkt_byte_sum ok 4 stats.qstat_by_ifindex ok 5 stats.check_down # SKIP marked as disruptive # Totals: pass:4 fail:0 xfail:0 xpass:0 skip:1 error:0 v3: - parse yes and properly treat non-zero nums as true (Petr) v2: - convert from cli argument to env variable (Jakub) Signed-off-by:
-
Stanislav Fomichev authored
Verify that total device stats don't decrease after it has been turned down. Also make sure the device doesn't crash when we access per-queue stats when it's down (in case it tries to access some pointers that are NULL). KTAP version 1 1..5 ok 1 stats.check_pause ok 2 stats.check_fec ok 3 stats.pkt_byte_sum ok 4 stats.qstat_by_ifindex ok 5 stats.check_down # Totals: pass:5 fail:0 xfail:0 xpass:0 skip:0 error:0 v3: - use errno.EOPNOTSUPP (Petr) - move qstat[0] under try (Petr) v2: - KTAP output formatting (Jakub) - defer instead of try/finally (Jakub) - disappearing stats is an error (Jakub) - ksft_ge instead of open coding (Jakub) Signed-off-by:
-
Jakub Kicinski authored
We re-define values of enum netdev_priv_flags as preprocessor macros with the same name. I guess this was done to avoid breaking out of tree modules which may use #ifdef X for kernel compatibility? Commit 7aa98047 ("net: move net_device priv_flags out from UAPI") which added the enum doesn't say. In any case, the flags with defines are quite old now, and defines for new flags don't get added. OOT drivers have to resort to code greps for compat detection, anyway. Let's delete these defines, save LoC, help LXR link to the right place. Reviewed-by:
Jiri Pirko <jiri@nvidia.com> Link: https://patch.msgid.link/20240801163401.378723-1-kuba@kernel.orgSigned-off-by:
-
David S. Miller authored
Radhey Shyam Pandey says: ==================== net: axienet: Fix coding style issues This patchset replace all occurences of (1<<x) by BIT(x) to get rid of checkpatch.pl "CHECK" output "Prefer using the BIT macro". It also removes unnecessary ftrace-like logging, add missing blank line after declaration and remove unnecessary parentheses around 'ndev->mtu <= XAE_JUMBO_MTU' and 'ndev->mtu > XAE_MTU'. Changes for v2: - Split each coding style change into separate patch. ==================== Signed-off-by: -
Radhey Shyam Pandey authored
Remove unnecessary parentheses around 'ndev->mtu <= XAE_JUMBO_MTU' and 'ndev->mtu > XAE_MTU'. Reported by checkpatch. CHECK: Unnecessary parentheses around 'ndev->mtu > XAE_MTU' + if ((ndev->mtu > XAE_MTU) && + (ndev->mtu <= XAE_JUMBO_MTU)) { CHECK: Unnecessary parentheses around 'ndev->mtu <= XAE_JUMBO_MTU' + if ((ndev->mtu > XAE_MTU) && + (ndev->mtu <= XAE_JUMBO_MTU)) { Signed-off-by:Radhey Shyam Pandey <radhey.shyam.pandey@amd.com> Reviewed-by:
-
Radhey Shyam Pandey authored
remove unnecessary ftrace-like logging. Also fixes below checkpatch WARNING. WARNING: Unnecessary ftrace-like logging - prefer using ftrace + dev_dbg(&ndev->dev, "%s\n", __func__); Signed-off-by:
-
Radhey Shyam Pandey authored
Add missing blank line after declaration. Fixes below checkpatch warnings. WARNING: Missing a blank line after declarations + struct sockaddr *addr = p; + axienet_set_mac_address(ndev, addr->sa_data); WARNING: Missing a blank line after declarations + struct axienet_local *lp = netdev_priv(ndev); + disable_irq(lp->tx_irq); Signed-off-by:
-
Appana Durga Kedareswara Rao authored
Replace all occurences of (1<<x) by BIT(x) to get rid of checkpatch.pl "CHECK" output "Prefer using the BIT macro". Signed-off-by:
Appana Durga Kedareswara Rao <appana.durga.rao@xilinx.com> Signed-off-by:
-
David S. Miller authored
Luigi Leonardi says: ==================== vsock: avoid queuing on intermediate queue if possible This series introduces an optimization for vsock/virtio to reduce latency and increase the throughput: When the guest sends a packet to the host, and the intermediate queue (send_pkt_queue) is empty, if there is enough space, the packet is put directly in the virtqueue. v3->v4 While running experiments on fio with 64B payload, I realized that there was a mistake in my fio configuration, so I re-ran all the experiments and now the latency numbers are indeed lower with the patch applied. I also noticed that I was kicking the host without the lock. - Fixed a configuration mistake on fio and re-ran all experiments. - Fio latency measurement using 64B payload. - virtio_transport_send_skb_fast_path sends kick with the tx_lock acquired - Addressed all minor style changes requested by maintainer. - Rebased on latest net-next - Link to v3: https://lore.kernel.org/r/20240711-pinna-v3-0-697d4164fe80@outlook.com v2->v3 - Performed more experiments using iperf3 using multiple streams - Handling of reply packets removed from virtio_transport_send_skb, as is needed just by the worker. - Removed atomic_inc/atomic_sub when queuing directly to the vq. - Introduced virtio_transport_send_skb_fast_path that handles the steps for sending on the vq. - Fixed a missing mutex_unlock in error path. - Changed authorship of the second commit - Rebased on latest net-next v1->v2 In this v2 I replaced a mutex_lock with a mutex_trylock because it was insidea RCU critical section. I also added a check on tx_run, so if the module is being removed the packet is not queued. I'd like to thank Stefano for reporting the tx_run issue. Applied all Stefano's suggestions: - Minor code style changes - Minor commit text rewrite Performed more experiments: - Check if all the packets go directly to the vq (Matias' suggestion) - Used iperf3 to see if there is any improvement in overall throughput from guest to host - Pinned the vhost process to a pCPU. - Run fio using 512B payload Rebased on latest net-next ==================== Signed-off-by:
-
