- 21 Apr, 2015 7 commits
-
-
Christian Gmeiner authored
commit aadca6fa upstream. Certec BPC600 needs reboot=pci to actually reboot. Signed-off-by:
Christian Gmeiner <christian.gmeiner@gmail.com> Cc: Matthew Garrett <mjg59@srcf.ucam.org> Cc: Li Aubrey <aubrey.li@linux.intel.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Dave Jones <davej@redhat.com> Cc: Fenghua Yu <fenghua.yu@intel.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Link: http://lkml.kernel.org/r/1399446114-2147-1-git-send-email-christian.gmeiner@gmail.comSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
Jiri Slaby <jslaby@suse.cz>
-
Jiri Slaby authored
commit e56e57f6 upstream. Grouping them by vendor should make it easier to spot duplicates. Signed-off-by:
Dave Jones <davej@fedoraproject.org> Link: http://lkml.kernel.org/r/20131001203655.GA10719@redhat.comSigned-off-by:
-
Masoud Sharbiani authored
commit b5eafc6f upstream. Two entries for the same system type were added, with two different vendor names: 'Dell' and 'Dell, Inc.'. Since a prefix match is being used by the DMI parsing code, we can eliminate the latter as redundant. Reported-by:
"H. Peter Anvin" <hpa@zytor.com> Signed-off-by:
Masoud Sharbiani <msharbiani@twitter.com> Cc: holt@sgi.com Link: http://lkml.kernel.org/r/1380216643-4683-1-git-send-email-masoud.sharbiani@gmail.comSigned-off-by:
-
Ameya Palande authored
commit c8648508 upstream. On success, callback function returns 0. So invert the if condition check so that we can break out of loop. Signed-off-by:
Ameya Palande <2ameya@gmail.com> Signed-off-by:
Lee Jones <lee.jones@linaro.org> Signed-off-by:
-
Markos Chandras authored
commit 87f966d9 upstream. On a MIPS Malta board, tons of fifo underflow errors have been observed when using u-boot as bootloader instead of YAMON. The reason for that is that YAMON used to set the pcnet device to SRAM mode but u-boot does not. As a result, the default Tx threshold (64 bytes) is now too small to keep the fifo relatively used and it can result to Tx fifo underflow errors. As a result of which, it's best to setup the SRAM on supported controllers so we can always use the NOUFLO bit. Cc: <netdev@vger.kernel.org> Cc: <linux-kernel@vger.kernel.org> Cc: Don Fry <pcnet32@frontier.com> Signed-off-by:
Markos Chandras <markos.chandras@imgtec.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Tyrel Datwyler authored
commit f6ff0414 upstream. We currently use the device tree update code in the kernel after resuming from a suspend operation to re-sync the kernels view of the device tree with that of the hypervisor. The code as it stands is not endian safe as it relies on parsing buffers returned by RTAS calls that thusly contains data in big endian format. This patch annotates variables and structure members with __be types as well as performing necessary byte swaps to cpu endian for data that needs to be parsed. Signed-off-by:
Tyrel Datwyler <tyreld@linux.vnet.ibm.com> Cc: Nathan Fontenot <nfont@linux.vnet.ibm.com> Cc: Cyril Bur <cyrilbur@gmail.com> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Catalin Marinas authored
commit e53f21bc upstream. The idle_task_exit() function may call switch_mm() with next == &init_mm. On arm64, init_mm.pgd cannot be used for user mappings, so this patch simply sets the reserved TTBR0. Reported-by:
Jon Medhurst (Tixy) <tixy@linaro.org> Tested-by:
Catalin Marinas <catalin.marinas@arm.com> Signed-off-by:
-
- 13 Apr, 2015 1 commit
-
-
Jiri Slaby authored
Stable commit "core, nfqueue, openvswitch: Orphan frags in skb_zerocopy and handle errors", upstream commit 36d5fe6a, was not correctly backported and missed to change a const 'from' parameter to non-const. This results in a new batch of warnings: net/netfilter/nfnetlink_queue_core.c: In function ‘nfqnl_zcopy’: net/netfilter/nfnetlink_queue_core.c:272:2: warning: passing argument 1 of ‘skb_orphan_frags’ discards ‘const’ qualifier from pointer target type [enabled by default] if (unlikely(skb_orphan_frags(from, GFP_ATOMIC))) { ^ In file included from net/netfilter/nfnetlink_queue_core.c:18:0: include/linux/skbuff.h:1822:19: note: expected ‘struct sk_buff *’ but argument is of type ‘const struct sk_buff *’ static inline int skb_orphan_frags(struct sk_buff *skb, gfp_t gfp_mask) ^ net/netfilter/nfnetlink_queue_core.c:273:3: warning: passing argument 1 of ‘skb_tx_error’ discards ‘const’ qualifier from pointer target type [enabled by default] skb_tx_error(from); ^ In file included from net/netfilter/nfnetlink_queue_core.c:18:0: include/linux/skbuff.h:630:13: note: expected ‘struct sk_buff *’ but argument is of type ‘const struct sk_buff *’ extern void skb_tx_error(struct sk_buff *skb); Remove const from the 'from' parameter, the same as in the upstream commit. As far as I can see, this leaked into 3.10, 3.12, and 3.13 already. Cc: Zoltan Kiss <zoltan.kiss@citrix.com> Cc: David S. Miller <davem@davemloft.net> Cc: Ben Hutchings <ben@decadent.org.uk> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: stable@vger.kernel.org # v3.10, v3.12, v3.13 Signed-off-by:
-
- 09 Apr, 2015 32 commits
-
-
Jiri Slaby authored
-
Sergei Antonov authored
commit 98cf21c6 upstream. Fix B-tree corruption when a new record is inserted at position 0 in the node in hfs_brec_insert(). In this case a hfs_brec_update_parent() is called to update the parent index node (if exists) and it is passed hfs_find_data with a search_key containing a newly inserted key instead of the key to be updated. This results in an inconsistent index node. The bug reproduces on my machine after an extents overflow record for the catalog file (CNID=4) is inserted into the extents overflow B-tree. Because of a low (reserved) value of CNID=4, it has to become the first record in the first leaf node. The resulting first leaf node is correct: ---------------------------------------------------- | key0.CNID=4 | key1.CNID=123 | key2.CNID=456, ... | ---------------------------------------------------- But the parent index key0 still contains the previous key CNID=123: ----------------------- | key0.CNID=123 | ... | ----------------------- A change in hfs_brec_insert() makes hfs_brec_update_parent() work correctly by preventing it from getting fd->record=-1 value from __hfs_brec_find(). Along the way, I removed duplicate code with unification of the if condition. The resulting code is equivalent to the original code because node is never 0. Also hfs_brec_update_parent() will now return an error after getting a negative fd->record value. However, the return value of hfs_brec_update_parent() is not checked anywhere in the file and I'm leaving it unchanged by this patch. brec.c lacks error checking after some other calls too, but this issue is of less importance than the one being fixed by this patch. Signed-off-by:
Sergei Antonov <saproj@gmail.com> Cc: Joe Perches <joe@perches.com> Reviewed-by:
Vyacheslav Dubeyko <slava@dubeyko.com> Acked-by:
Hin-Tak Leung <htl10@users.sourceforge.net> Cc: Anton Altaparmakov <aia21@cam.ac.uk> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Christoph Hellwig <hch@infradead.org> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Darrick J. Wong authored
commit e5db2980 upstream. Since it's possible for the discard and write same queue limits to change while the upper level command is being sliced and diced, fix up both of them (a) to reject IO if the special command is unsupported at the start of the function and (b) read the limits once and let the commands error out on their own if the status happens to change. Signed-off-by:
Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by:
Mikulas Patocka <mpatocka@redhat.com> Signed-off-by:
Mike Snitzer <snitzer@redhat.com> Signed-off-by:
-
Mikulas Patocka authored
commit ab7c7bb6 upstream. __dm_destroy() must take the suspend_lock so that its presuspend and postsuspend calls do not race with an internal suspend. Signed-off-by:
-
Andy Shevchenko authored
commit a104a45b upstream. The commit 9cade1a4 (dma: dw: split driver to library part and platform code) introduced a separate platform driver but missed to add a MODULE_ALIAS("platform:dw_dmac"); to that module. The patch adds this to get driver loaded automatically if platform device is registered. Reported-by:
"Blin, Jerome" <jerome.blin@intel.com> Fixes: 9cade1a4 (dma: dw: split driver to library part and platform code) Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
Vinod Koul <vinod.koul@intel.com> Signed-off-by:
-
Malcolm Priestley authored
commit 40c8790b upstream. When the driver sets this rate a power of zero value is set causing data flow stoppage until another rate is tried. Signed-off-by:
Malcolm Priestley <tvboxspy@gmail.com> Signed-off-by:
-
Peter Zijlstra authored
commit d525211f upstream. Vince reported a watchdog lockup like: [<ffffffff8115e114>] perf_tp_event+0xc4/0x210 [<ffffffff810b4f8a>] perf_trace_lock+0x12a/0x160 [<ffffffff810b7f10>] lock_release+0x130/0x260 [<ffffffff816c7474>] _raw_spin_unlock_irqrestore+0x24/0x40 [<ffffffff8107bb4d>] do_send_sig_info+0x5d/0x80 [<ffffffff811f69df>] send_sigio_to_task+0x12f/0x1a0 [<ffffffff811f71ce>] send_sigio+0xae/0x100 [<ffffffff811f72b7>] kill_fasync+0x97/0xf0 [<ffffffff8115d0b4>] perf_event_wakeup+0xd4/0xf0 [<ffffffff8115d103>] perf_pending_event+0x33/0x60 [<ffffffff8114e3fc>] irq_work_run_list+0x4c/0x80 [<ffffffff8114e448>] irq_work_run+0x18/0x40 [<ffffffff810196af>] smp_trace_irq_work_interrupt+0x3f/0xc0 [<ffffffff816c99bd>] trace_irq_work_interrupt+0x6d/0x80 Which is caused by an irq_work generating new irq_work and therefore not allowing forward progress. This happens because processing the perf irq_work triggers another perf event (tracepoint stuff) which in turn generates an irq_work ad infinitum. Avoid this by raising the recursion counter in the irq_work -- which effectively disables all software events (including tracepoints) from actually triggering again. Reported-by:
Vince Weaver <vincent.weaver@maine.edu> Tested-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Arnaldo Carvalho de Melo <acme@kernel.org> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Paul Mackerras <paulus@samba.org> Cc: Steven Rostedt <rostedt@goodmis.org> Link: http://lkml.kernel.org/r/20150219170311.GH21418@twins.programming.kicks-ass.netSigned-off-by:
-
Bob Copeland authored
commit d0c22119 upstream. The mesh forwarding path was not checking that data frames were protected when running an encrypted network; add the necessary check. Reported-by:
Johannes Berg <johannes@sipsolutions.net> Signed-off-by:
Bob Copeland <me@bobcopeland.com> Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Michal Kazior authored
commit aa75ebc2 upstream. Some APs experience problems when working with U-APSD. Decreasing the probability of that happening by using legacy mode for all ACs but VO isn't enough. Cisco 4410N originally forced us to enable VO by default only because it treated non-VO ACs as legacy. However some APs (notably Netgear R7000) silently reclassify packets to different ACs. Since u-APSD ACs require trigger frames for frame retrieval clients would never see some frames (e.g. ARP responses) or would fetch them accidentally after a long time. It makes little sense to enable u-APSD queues by default because it needs userspace applications to be aware of it to actually take advantage of the possible additional powersavings. Implicitly depending on driver autotrigger frame support doesn't make much sense. Signed-off-by:
Michal Kazior <michal.kazior@tieto.com> Signed-off-by:
-
Johannes Berg authored
commit 496fcc29 upstream. As HT/VHT depend heavily on QoS/WMM, it's not a good idea to let userspace add clients that have HT/VHT but not QoS/WMM. Since it does so in certain cases we've observed (client is using HT IEs but not QoS/WMM) just ignore the HT/VHT info at this point and don't pass it down to the drivers which might unconditionally use it. Signed-off-by:
-
Bart Van Assche authored
commit 75c3d0bf upstream. This patch fixes the incorrect use of __transport_register_session() in tcm_qla2xxx_check_initiator_node_acl() code, that does not perform explicit se_tpg->session_lock when accessing se_tpg->tpg_sess_list to add new se_sess nodes. Given that tcm_qla2xxx_check_initiator_node_acl() is not called with qla_hw->hardware_lock held for all accesses of ->tpg_sess_list, the code should be using transport_register_session() instead. Signed-off-by:
Bart Van Assche <bart.vanassche@sandisk.com> Cc: Giridhar Malavali <giridhar.malavali@qlogic.com> Cc: Quinn Tran <quinn.tran@qlogic.com> Signed-off-by:
Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by:
-
Dan Carpenter authored
commit d556546e upstream. This patch adds a missing set of conditional check braces in ft_invl_hw_context() originally introduced by commit dcd998cc when handling DDP failures in ft_recv_write_data() code. commit dcd998cc Author: Kiran Patil <kiran.patil@intel.com> Date: Wed Aug 3 09:20:01 2011 +0000 tcm_fc: Handle DDP/SW fc_frame_payload_get failures in ft_recv_write_data Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Cc: Kiran Patil <kiran.patil@intel.com> Signed-off-by:
-
Lars-Peter Clausen authored
commit 328f494d upstream. When inserting a new register into a block at the lower end the present bitmap is currently shifted into the wrong direction. The effect of this is that the bitmap becomes corrupted and registers which are present might be reported as not present and vice versa. Fix this by shifting left rather than right. Fixes: 472fdec7("regmap: rbtree: Reduce number of nodes, take 2") Reported-by:
Daniel Baluta <daniel.baluta@gmail.com> Signed-off-by:
Lars-Peter Clausen <lars@metafoo.de> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Takashi Iwai authored
commit 07892b10 upstream. The correct values referred by a boolean control are value.integer.value[], not value.enumerated.item[]. The former is long while the latter is int, so it's even incompatible on 64bit architectures. Signed-off-by:
Takashi Iwai <tiwai@suse.de> Acked-by:
Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by:
-
Takashi Iwai authored
commit 2bf4c1d4 upstream. The correct values referred by a boolean control are value.integer.value[], not value.enumerated.item[]. The former is long while the latter is int, so it's even incompatible on 64bit architectures. Signed-off-by:
-
Takashi Iwai authored
commit 08641d9b upstream. The correct values referred by a boolean control are value.integer.value[], not value.enumerated.item[]. The former is long while the latter is int, so it's even incompatible on 64bit architectures. Signed-off-by:
-
Takashi Iwai authored
commit eaddf6fd upstream. The correct values referred by a boolean control are value.integer.value[], not value.enumerated.item[]. The former is long while the latter is int, so it's even incompatible on 64bit architectures. Signed-off-by:
-
Takashi Iwai authored
commit 24cc883c upstream. The correct values referred by a boolean control are value.integer.value[], not value.enumerated.item[]. The former is long while the latter is int, so it's even incompatible on 64bit architectures. Signed-off-by:
-
Takashi Iwai authored
commit 00a14c29 upstream. The correct values referred by a boolean control are value.integer.value[], not value.enumerated.item[]. The former is long while the latter is int, so it's even incompatible on 64bit architectures. Signed-off-by:
-
Takashi Iwai authored
commit bd14016f upstream. The correct values referred by a boolean control are value.integer.value[], not value.enumerated.item[]. The former is long while the latter is int, so it's even incompatible on 64bit architectures. Signed-off-by:
-
Takashi Iwai authored
commit 4c523ef6 upstream. The correct values referred by a boolean control are value.integer.value[], not value.enumerated.item[]. The former is long while the latter is int, so it's even incompatible on 64bit architectures. Signed-off-by:
-
Takashi Iwai authored
commit b4a18c8b upstream. The correct values referred by a boolean control are value.integer.value[], not value.enumerated.item[]. The former is long while the latter is int, so it's even incompatible on 64bit architectures. Signed-off-by:
-
Takashi Iwai authored
commit e8371aa0 upstream. The correct values referred by a boolean control are value.integer.value[], not value.enumerated.item[]. The former is long while the latter is int, so it's even incompatible on 64bit architectures. Signed-off-by:
Paul Handrigan <Paul.Handrigan@cirrus.com> Signed-off-by:
-
Takashi Iwai authored
commit d7f58db4 upstream. The correct values referred by a boolean control are value.integer.value[], not value.enumerated.item[]. The former is long while the latter is int, so it's even incompatible on 64bit architectures. Signed-off-by:
-
Eric Nelson authored
commit c7d910b8 upstream. The SGTL5000_CHIP_ANA_POWER register is cached. Update the cached value instead of writing it directly. Patch inspired by Russell King's more colorful remarks in this patch: https://github.com/SolidRun/linux-imx6-3.14/commit/dd4bf6aSigned-off-by:
Eric Nelson <eric.nelson@boundarydevices.com> Signed-off-by:
-
willy tarreau authored
commit 71f6d1b3 upstream. Right now the mvneta driver doesn't handle Tx IRQ, and relies on two mechanisms to flush Tx descriptors : a flush at the end of mvneta_tx() and a timer. If a burst of packets is emitted faster than the device can send them, then the queue is stopped until next wake-up of the timer 10ms later. This causes jerky output traffic with bursts and pauses, making it difficult to reach line rate with very few streams. A test on UDP traffic shows that it's not possible to go beyond 134 Mbps / 12 kpps of outgoing traffic with 1500-bytes IP packets. Routed traffic tends to observe pauses as well if the traffic is bursty, making it even burstier after the wake-up. It seems that this feature was inherited from the original driver but nothing there mentions any reason for not using the interrupt instead, which the chip supports. Thus, this patch enables Tx interrupts and removes the timer. It does the two at once because it's not really possible to make the two mechanisms coexist, so a split patch doesn't make sense. First tests performed on a Mirabox (Armada 370) show that less CPU seems to be used when sending traffic. One reason might be that we now call the mvneta_tx_done_gbe() with a mask indicating which queues have been done instead of looping over all of them. The same UDP test above now happily reaches 987 Mbps / 87.7 kpps. Single-stream TCP traffic can now more easily reach line rate. HTTP transfers of 1 MB objects over a single connection went from 730 to 840 Mbps. It is even possible to go significantly higher (>900 Mbps) by tweaking tcp_tso_win_divisor. Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Cc: Gregory CLEMENT <gregory.clement@free-electrons.com> Cc: Arnaud Ebalard <arno@natisbad.org> Cc: Eric Dumazet <eric.dumazet@gmail.com> Tested-by:
Arnaud Ebalard <arno@natisbad.org> Signed-off-by:
Willy Tarreau <w@1wt.eu> Signed-off-by:
-
willy tarreau authored
commit 40ba35e7 upstream. Marvell has not published the chip's datasheet yet, so it's very hard to find the relevant bits to manipulate to change the IRQ behaviour. Fortunately, these bits are described in the proprietary LSP patch set which is publicly available here : http://www.plugcomputer.org/downloads/mirabox/ So let's put them back in the driver in order to reduce the burden of current and future maintenance. Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Cc: Gregory CLEMENT <gregory.clement@free-electrons.com> Tested-by:
-
willy tarreau authored
commit 29021366 upstream. If a queue timeout is reported, we can oops because of some schedules while the caller is atomic, as shown below : mvneta d0070000.ethernet eth0: tx timeout BUG: scheduling while atomic: bash/1528/0x00000100 Modules linked in: slhttp_ethdiv(C) [last unloaded: slhttp_ethdiv] CPU: 2 PID: 1528 Comm: bash Tainted: G WC 3.13.0-rc4-mvebu-nf #180 [<c0011bd9>] (unwind_backtrace+0x1/0x98) from [<c000f1ab>] (show_stack+0xb/0xc) [<c000f1ab>] (show_stack+0xb/0xc) from [<c02ad323>] (dump_stack+0x4f/0x64) [<c02ad323>] (dump_stack+0x4f/0x64) from [<c02abe67>] (__schedule_bug+0x37/0x4c) [<c02abe67>] (__schedule_bug+0x37/0x4c) from [<c02ae261>] (__schedule+0x325/0x3ec) [<c02ae261>] (__schedule+0x325/0x3ec) from [<c02adb97>] (schedule_timeout+0xb7/0x118) [<c02adb97>] (schedule_timeout+0xb7/0x118) from [<c0020a67>] (msleep+0xf/0x14) [<c0020a67>] (msleep+0xf/0x14) from [<c01dcbe5>] (mvneta_stop_dev+0x21/0x194) [<c01dcbe5>] (mvneta_stop_dev+0x21/0x194) from [<c01dcfe9>] (mvneta_tx_timeout+0x19/0x24) [<c01dcfe9>] (mvneta_tx_timeout+0x19/0x24) from [<c024afc7>] (dev_watchdog+0x18b/0x1c4) [<c024afc7>] (dev_watchdog+0x18b/0x1c4) from [<c0020b53>] (call_timer_fn.isra.27+0x17/0x5c) [<c0020b53>] (call_timer_fn.isra.27+0x17/0x5c) from [<c0020cad>] (run_timer_softirq+0x115/0x170) [<c0020cad>] (run_timer_softirq+0x115/0x170) from [<c001ccb9>] (__do_softirq+0xbd/0x1a8) [<c001ccb9>] (__do_softirq+0xbd/0x1a8) from [<c001cfad>] (irq_exit+0x61/0x98) [<c001cfad>] (irq_exit+0x61/0x98) from [<c000d4bf>] (handle_IRQ+0x27/0x60) [<c000d4bf>] (handle_IRQ+0x27/0x60) from [<c000843b>] (armada_370_xp_handle_irq+0x33/0xc8) [<c000843b>] (armada_370_xp_handle_irq+0x33/0xc8) from [<c000fba9>] (__irq_usr+0x49/0x60) Ben Hutchings attempted to propose a better fix consisting in using a scheduled work for this, but while it fixed this panic, it caused other random freezes and panics proving that the reset sequence in the driver is unreliable and that additional fixes should be investigated. When sending multiple streams over a link limited to 100 Mbps, Tx timeouts happen from time to time, and the driver correctly recovers only when the function is disabled. Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Cc: Gregory CLEMENT <gregory.clement@free-electrons.com> Cc: Ben Hutchings <ben@decadent.org.uk> Tested-by:
-
willy tarreau authored
commit 74c41b04 upstream. Stats writers are mvneta_rx() and mvneta_tx(). They don't lock anything when they update the stats, and as a result, it randomly happens that the stats freeze on SMP if two updates happen during stats retrieval. This is very easily reproducible by starting two HTTP servers and binding each of them to a different CPU, then consulting /proc/net/dev in loops during transfers, the interface should immediately lock up. This issue also randomly happens upon link state changes during transfers, because the stats are collected in this situation, but it takes more attempts to reproduce it. The comments in netdevice.h suggest using per_cpu stats instead to get rid of this issue. This patch implements this. It merges both rx_stats and tx_stats into a single "stats" member with a single syncp. Both mvneta_rx() and mvneta_rx() now only update the a single CPU's counters. In turn, mvneta_get_stats64() does the summing by iterating over all CPUs to get their respective stats. With this change, stats are still correct and no more lockup is encountered. Note that this bug was present since the first import of the mvneta driver. It might make sense to backport it to some stable trees. If so, it depends on "d33dc73 net: mvneta: increase the 64-bit rx/tx stats out of the hot path". Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Cc: Gregory CLEMENT <gregory.clement@free-electrons.com> Reviewed-by:
Eric Dumazet <edumazet@google.com> Tested-by:
-
willy tarreau authored
commit dc4277dd upstream. Better count packets and bytes in the stack and on 32 bit then accumulate them at the end for once. This saves two memory writes and two memory barriers per packet. The incoming packet rate was increased by 4.7% on the Openblocks AX3 thanks to this. Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Cc: Gregory CLEMENT <gregory.clement@free-electrons.com> Reviewed-by:
-
Wei Yang authored
[ Upstream commit befdf897 ] pci_match_id() just match the static pci_device_id, which may return NULL if someone binds the driver to a device manually using /sys/bus/pci/drivers/.../new_id. This patch wrap up a helper function __mlx4_remove_one() which does the tear down function but preserve the drv_data. Functions like mlx4_pci_err_detected() and mlx4_restart_one() will call this one with out releasing drvdata. Fixes: 97a5221f "net/mlx4_core: pass pci_device_id.driver_data to __mlx4_init_one during reset". CC: Bjorn Helgaas <bhelgaas@google.com> CC: Amir Vadai <amirv@mellanox.com> CC: Jack Morgenstein <jackm@dev.mellanox.co.il> CC: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by:
Wei Yang <weiyang@linux.vnet.ibm.com> Acked-by:
Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Wei Yang authored
commit 97a5221f upstream. The second parameter of __mlx4_init_one() is used to identify whether the pci_dev is a PF or VF. Currently, when it is invoked in mlx4_pci_slot_reset() this information is missed. This patch match the pci_dev with mlx4_pci_table and passes the pci_device_id.driver_data to __mlx4_init_one() in mlx4_pci_slot_reset(). Signed-off-by:
-
