- 28 Jun, 2018 1 commit
-
-
Evan Quan authored
Thermal support is enabled on vega12. Signed-off-by:
Evan Quan <evan.quan@amd.com> Acked-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
- 27 Jun, 2018 3 commits
-
-
Shirish S authored
Currently, amdgpu_do_flip() spinlocks crtc->dev->event_lock and releases it only after committing updates to the stream. dc_commit_updates_for_stream() should be moved out of spinlock for the below reasons: 1. event_lock is supposed to protect access to acrct->pflip_status _only_ 2. dc_commit_updates_for_stream() has potential sleep's and also its not appropriate to be in an atomic state for such long sequences of code. Signed-off-by:
Shirish S <shirish.s@amd.com> Suggested-by:
Andrey Grodzovsky <andrey.grodzovsky@amd.com> Reviewed-by:
Michel Dänzer <michel.daenzer@amd.com> Reviewed-by:
Harry Wentland <harry.wentland@amd.com> Signed-off-by:
-
James Zhu authored
Support new VCN FW version naming convention: [31, 28] for VEP interface major version if applicable [27, 24] for decode interface major version [23, 20] for encode interface major version [19, 12] for encode interface minor version [11, 0] for firmware revision Bit 20-23, it is encode major and non-zero for new naming convention. This field is part of version minor and DRM_DISABLED_FLAG in old naming convention. Since the latest version minor is 0x5B and DRM_DISABLED_FLAG is zero in old naming convention, this field is always zero so far. These four bits are used to tell which naming convention is present. Signed-off-by:
James Zhu <James.Zhu@amd.com> Reviewed-by:
Fang, Peter <Peter.Fang@amd.com> Signed-off-by:
-
Leo Liu authored
Here is the UBSAN dump: [ 3.866656] index 2 is out of range for type 'amdgpu_uvd_inst [2]' [ 3.866693] Workqueue: events work_for_cpu_fn [ 3.866702] Call Trace: [ 3.866710] dump_stack+0x85/0xc5 [ 3.866719] ubsan_epilogue+0x9/0x40 [ 3.866727] __ubsan_handle_out_of_bounds+0x89/0x90 [ 3.866737] ? rcu_read_lock_sched_held+0x58/0x60 [ 3.866746] ? __kmalloc+0x26c/0x2d0 [ 3.866846] amdgpu_fence_driver_start_ring+0x259/0x280 [amdgpu] [ 3.866896] amdgpu_ring_init+0x12c/0x710 [amdgpu] [ 3.866906] ? sprintf+0x42/0x50 [ 3.866956] amdgpu_gfx_kiq_init_ring+0x1bc/0x3a0 [amdgpu] [ 3.867009] gfx_v8_0_sw_init+0x1ad3/0x2360 [amdgpu] [ 3.867062] ? smu7_init+0xec/0x160 [amdgpu] [ 3.867109] amdgpu_device_init+0x112c/0x1dc0 [amdgpu] 'ring->me' might be set as 2 with 'amdgpu_gfx_kiq_init_ring', that would cause out of range for 'amdgpu_uvd_inst[2]'. v2: simplified with ring type Signed-off-by:
Leo Liu <leo.liu@amd.com> Reviewed-by:
-
- 22 Jun, 2018 3 commits
-
-
Michel Dänzer authored
start / last / max_entries are numbers of GPU pages, pfn / count are numbers of CPU pages. Convert between them accordingly. Fixes badness on systems with > 4K page size. Cc: stable@vger.kernel.org Bugzilla: https://bugs.freedesktop.org/106258Reported-by:
Matt Corallo <freedesktop@bluematt.me> Tested-by: foxbat@ruin.net Reviewed-by:
Christian König <christian.koenig@amd.com> Signed-off-by:
-
Lyude Paul authored
This fixes a regression I accidentally reduced that was picked up by kasan, where we were checking the CRTC atomic states after DRM's helpers had already freed them. Example: ================================================================== BUG: KASAN: use-after-free in amdgpu_dm_atomic_commit_tail.cold.50+0x13d/0x15a [amdgpu] Read of size 1 at addr ffff8803a697b071 by task kworker/u16:0/7 CPU: 7 PID: 7 Comm: kworker/u16:0 Tainted: G O 4.18.0-rc1Lyude-Upstream+ #1 Hardware name: HP HP ZBook 15 G4/8275, BIOS P70 Ver. 01.21 05/02/2018 Workqueue: events_unbound commit_work [drm_kms_helper] Call Trace: dump_stack+0xc1/0x169 ? dump_stack_print_info.cold.1+0x42/0x42 ? kmsg_dump_rewind_nolock+0xd9/0xd9 ? printk+0x9f/0xc5 ? amdgpu_dm_atomic_commit_tail.cold.50+0x13d/0x15a [amdgpu] print_address_description+0x6c/0x23c ? amdgpu_dm_atomic_commit_tail.cold.50+0x13d/0x15a [amdgpu] kasan_report.cold.6+0x241/0x2fd amdgpu_dm_atomic_commit_tail.cold.50+0x13d/0x15a [amdgpu] ? commit_planes_to_stream.constprop.45+0x13b0/0x13b0 [amdgpu] ? cpu_load_update_active+0x290/0x290 ? finish_task_switch+0x2bd/0x840 ? __switch_to_asm+0x34/0x70 ? read_word_at_a_time+0xe/0x20 ? strscpy+0x14b/0x460 ? drm_atomic_helper_wait_for_dependencies+0x47d/0x7e0 [drm_kms_helper] commit_tail+0x96/0xe0 [drm_kms_helper] process_one_work+0x88a/0x1360 ? create_worker+0x540/0x540 ? __sched_text_start+0x8/0x8 ? move_queued_task+0x760/0x760 ? call_rcu_sched+0x20/0x20 ? vsnprintf+0xcda/0x1350 ? wait_woken+0x1c0/0x1c0 ? mutex_unlock+0x1d/0x40 ? init_timer_key+0x190/0x230 ? schedule+0xea/0x390 ? __schedule+0x1ea0/0x1ea0 ? need_to_create_worker+0xe4/0x210 ? init_worker_pool+0x700/0x700 ? try_to_del_timer_sync+0xbf/0x110 ? del_timer+0x120/0x120 ? __mutex_lock_slowpath+0x10/0x10 worker_thread+0x196/0x11f0 ? flush_rcu_work+0x50/0x50 ? __switch_to_asm+0x34/0x70 ? __switch_to_asm+0x34/0x70 ? __switch_to_asm+0x40/0x70 ? __switch_to_asm+0x34/0x70 ? __switch_to_asm+0x40/0x70 ? __switch_to_asm+0x34/0x70 ? __switch_to_asm+0x40/0x70 ? __schedule+0x7d6/0x1ea0 ? migrate_swap_stop+0x850/0x880 ? __sched_text_start+0x8/0x8 ? save_stack+0x8c/0xb0 ? kasan_kmalloc+0xbf/0xe0 ? kmem_cache_alloc_trace+0xe4/0x190 ? kthread+0x98/0x390 ? ret_from_fork+0x35/0x40 ? ret_from_fork+0x35/0x40 ? deactivate_slab.isra.67+0x3c4/0x5c0 ? kthread+0x98/0x390 ? kthread+0x98/0x390 ? set_track+0x76/0x120 ? schedule+0xea/0x390 ? __schedule+0x1ea0/0x1ea0 ? wait_woken+0x1c0/0x1c0 ? kasan_unpoison_shadow+0x30/0x40 ? parse_args.cold.15+0x17a/0x17a ? flush_rcu_work+0x50/0x50 kthread+0x2d4/0x390 ? kthread_create_worker_on_cpu+0xc0/0xc0 ret_from_fork+0x35/0x40 Allocated by task 1124: kasan_kmalloc+0xbf/0xe0 kmem_cache_alloc_trace+0xe4/0x190 dm_crtc_duplicate_state+0x78/0x130 [amdgpu] drm_atomic_get_crtc_state+0x147/0x410 [drm] page_flip_common+0x57/0x230 [drm_kms_helper] drm_atomic_helper_page_flip+0xa6/0x110 [drm_kms_helper] drm_mode_page_flip_ioctl+0xc4b/0x10a0 [drm] drm_ioctl_kernel+0x1d4/0x260 [drm] drm_ioctl+0x433/0x920 [drm] amdgpu_drm_ioctl+0x11d/0x290 [amdgpu] do_vfs_ioctl+0x1a1/0x13d0 ksys_ioctl+0x60/0x90 __x64_sys_ioctl+0x6f/0xb0 do_syscall_64+0x147/0x440 entry_SYSCALL_64_after_hwframe+0x44/0xa9 Freed by task 1124: __kasan_slab_free+0x12e/0x180 kfree+0x92/0x1a0 drm_atomic_state_default_clear+0x315/0xc40 [drm] __drm_atomic_state_free+0x35/0xd0 [drm] drm_atomic_helper_update_plane+0xac/0x350 [drm_kms_helper] __setplane_internal+0x2d6/0x840 [drm] drm_mode_cursor_universal+0x41e/0xbe0 [drm] drm_mode_cursor_common+0x49f/0x880 [drm] drm_mode_cursor_ioctl+0xd8/0x130 [drm] drm_ioctl_kernel+0x1d4/0x260 [drm] drm_ioctl+0x433/0x920 [drm] amdgpu_drm_ioctl+0x11d/0x290 [amdgpu] do_vfs_ioctl+0x1a1/0x13d0 ksys_ioctl+0x60/0x90 __x64_sys_ioctl+0x6f/0xb0 do_syscall_64+0x147/0x440 entry_SYSCALL_64_after_hwframe+0x44/0xa9 The buggy address belongs to the object at ffff8803a697b068 which belongs to the cache kmalloc-1024 of size 1024 The buggy address is located 9 bytes inside of 1024-byte region [ffff8803a697b068, ffff8803a697b468) The buggy address belongs to the page: page:ffffea000e9a5e00 count:1 mapcount:0 mapping:ffff88041e00efc0 index:0x0 compound_mapcount: 0 flags: 0x8000000000008100(slab|head) raw: 8000000000008100 ffffea000ecbc208 ffff88041e000c70 ffff88041e00efc0 raw: 0000000000000000 0000000000170017 00000001ffffffff 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff8803a697af00: fb fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff8803a697af80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc >ffff8803a697b000: fc fc fc fc fc fc fc fc fc fc fc fc fc fb fb fb ^ ffff8803a697b080: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff8803a697b100: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ================================================================== So, we fix this by counting the number of CRTCs this atomic commit disabled early on in the function before their atomic states have been freed, then use that count later to do the appropriate number of RPM puts at the end of the function. Acked-by:Lyude Paul <lyude@redhat.com> Cc: Michel Dänzer <michel@daenzer.net> Reported-by:
Michel Dänzer <michel@daenzer.net> Signed-off-by:
-
git://anongit.freedesktop.org/drm/drm-miscDave Airlie authored
Fixes for v4.18-rc2: - A reversion of a commit in drm/sun4i to fix a run-time fault. - Various fixes to the sii8620 bridge. - Small bugfix to correctly check stride in atmel-hlcdc. Signed-off-by:
Dave Airlie <airlied@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/787d4bef-a579-4046-d0fc-f8c2c5b80c25@linux.intel.com
-
- 21 Jun, 2018 3 commits
-
-
Dave Airlie authored
Merge tag 'drm-intel-fixes-2018-06-21' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes drm/i915 fixes for v4.18-rc2: - Mostly cc: stable display fixes, including a DBLSCAN regression fix - GEM fixes for this merge window Signed-off-by:
-
Maciej Purski authored
Currently packed pixel modes in MHL2 can't be displayed. The device automatically recognizes output format, so setting format other than RGB causes failure. Fix it by writing proper values to registers. Tested on MHL1 and MHL2 using various vendors' dongles both in DVI and HDMI mode. Signed-off-by:
Maciej Purski <m.purski@samsung.com> Signed-off-by:
Andrzej Hajda <a.hajda@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/1516706239-9104-1-git-send-email-m.purski@samsung.com
-
git://people.freedesktop.org/~agd5f/linuxDave Airlie authored
Bunch of amdgpu fixes mostly all going to stable. Signed-off-by:
-
- 20 Jun, 2018 3 commits
-
-
git://anongit.freedesktop.org/drm/drm-miscDave Airlie authored
Only a small qxl fix that was queued for v4.17. Signed-off-by:
-
Dave Airlie authored
Merge tag 'drm-misc-next-fixes-2018-06-15' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes Single fix for v4.18: - Fix possible race conditions while unplugging DRM device. Signed-off-by:
-
git://github.com/skeggsb/linuxDave Airlie authored
Single nouveau regression fix. Signed-off-by:
-
- 19 Jun, 2018 16 commits
-
-
Michel Dänzer authored
Even BOs with AMDGPU_GEM_CREATE_NO_CPU_ACCESS may end up at least partially in CPU visible VRAM, in particular when all VRAM is visible. v2: * Don't take VRAM mgr spinlock, not needed (Christian König) * Make loop logic simpler and clearer. Cc: stable@vger.kernel.org Signed-off-by:
-
Michel Dänzer authored
Preparation for the following fix, no functional change intended. Cc: stable@vger.kernel.org Signed-off-by:
-
Michel Dänzer authored
At least in theory, ttm_bo_validate may move the BO, in which case the pin_size accounting would be inconsistent with when the BO was pinned. Cc: stable@vger.kernel.org Signed-off-by:
-
James Zhu authored
All UVD instanses have only one dpm control, so it is better to share one idle_work handle. Signed-off-by:
Stefan Agner <stefan@agner.ch> Signed-off-by:
-
Harry Wentland authored
We've had a number of users report failures to detect and light up display with DC with LVDS and VGA. These connector types are not currently supported with DC. I'd like to add support but unfortunately don't have a system with LVDS or VGA available. In order not to cause regressions we should probably fallback to the non-DC driver for ASICs that support VGA and LVDS. These ASICs are: * Bonaire * Kabini * Kaveri * Mullins ASIC support can always be force enabled with amdgpu.dc=1 v2: Keep Hawaii on DC v3: Added Mullins to the list Cc: stable@vger.kernel.org Signed-off-by:
-
Michel Dänzer authored
It can be quite big, and there's no need for it to be physically contiguous. This is less likely to fail under memory pressure (has actually happened while running piglit). Cc: stable@vger.kernel.org Signed-off-by:
-
Rajan Vaja authored
Initialize variable to 0 before performing logical OR operation. Reviewed-by:
Rex Zhu <Rex.Zhu@amd.com> Signed-off-by:
Rajan Vaja <rajan.vaja@gmail.com> Signed-off-by:
-
Kenneth Graunke authored
The SF and clipper units mishandle the provoking vertex in some cases, which can cause misrendering with shaders that use flat shaded inputs. There are chicken bits in 3D_CHICKEN3 (for SF) and FF_SLICE_CHICKEN (for the clipper) that work around the issue. These registers are unfortunately not part of the logical context (even the power context), and so we must reload them every time we start executing in a context. Bugzilla: https://bugs.freedesktop.org/103047Signed-off-by:
Kenneth Graunke <kenneth@whitecape.org> Signed-off-by:
Chris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20180615190605.16238-1-chris@chris-wilson.co.ukReviewed-by:
Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: stable@vger.kernel.org (cherry picked from commit b77422f8) Signed-off-by:
Jani Nikula <jani.nikula@intel.com>
-
Mika Kuoppala authored
If client is smart or lucky enough to create a new context after each hang, our context banning mechanism will never catch up, and as a result of that it will be saved from client banning. This can result in a never ending streak of gpu hangs caused by bad or malicious client, preventing access from other legit gpu clients. Fix this by always incrementing per client ban score if it hangs in short successions regardless of context ban scoring. The exception are non bannable contexts. They remain detached from client ban scoring mechanism. v2: xchg timestamp, tidyup (Chris) v3: comment, bannable & banned together (Chris) Fixes: b083a087 ("drm/i915: Add per client max context ban limit") Cc: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by:
Mika Kuoppala <mika.kuoppala@linux.intel.com> Reviewed-by:
-
Ville Syrjälä authored
While Bspec doesn't list a specific sequence for turning off the DP port on g4x we are getting an underrun if the port is disabled in the .disable() hook. Looks like the pipe stops when the port stops, and by that time the plane disable may not have completed yet. Also the plane(s) seem to end up in some wonky state when this happens as they also signal another underrun immediately after we turn them back on during the next enable sequence. We could add a vblank wait in .disable() to avoid wedging the planes, but I assume we're still tripping up the pipe in some way. So it seems better to me to just follow the ILK+ sequence and turn off the DP port in .post_disable() instead. This sequence doesn't seem to suffer from this problem. Could be it was always the intended sequence for DP and the gen4 bspec was just never updated to include it. Originally we used the bad sequence even on ilk+, but I changed that in commit 08aff3fe ("drm/i915: Move DP port disable to post_disable for pch platforms") as it was causing issues on those platforms as well. I left out g4x then only because I didn't have the hardware to test it. Now that I do it's fairly clear that the ilk+ sequence is also the right choice for g4x. v2: Fix whitespace fail (Jani) Mention the ilk+ commit (Jani) Cc: stable@vger.kernel.org Signed-off-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180613160553.11664-2-ville.syrjala@linux.intel.comReviewed-by:
-
Ville Syrjälä authored
Looks like interlaced DP output doesn't work on g4x either. Not all that surprising considering we already established that interlaced DP output is busted on VLV/CHV. Cc: stable@vger.kernel.org Signed-off-by:
-
Ville Syrjälä authored
On i965/g4x IIR is edge triggered. So in order for IIR to notice that there is still a pending interrupt we have to force and edge in ISR. For the ISR/IIR pipe event bits we can do that by temporarily clearing all the PIPESTAT enable bits when we ack the status bits. This will force the ISR pipe event bit low, and it can then go back high when we restore the PIPESTAT enable bits. This avoids the following race: 1. stat = read(PIPESTAT) 2. an enabled PIPESTAT status bit goes high 3. write(PIPESTAT, enable|stat); 4. write(IIR, PIPE_EVENT) The end result is IIR==0 and ISR!=0. This can lead to nasty vblank wait/flip_done timeouts if another interrupt source doesn't trick us into looking at the PIPESTAT status bits despite the IIR PIPE_EVENT bit being low. Before i965 IIR was level triggered so this problem can't actually happen there. And curiously VLV/CHV went back to the level triggered scheme as well. But for simplicity we'll use the same i965/g4x compatible code for all platforms. Cc: stable@vger.kernel.org Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=106033 Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105225 Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=106030Signed-off-by:
-
Ville Syrjälä authored
When encountering a connector with the scaling mode property both intel and modesetting ddxs sometimes add tons of DBLSCAN modes to the output's mode list. The idea presumably being that since the output will be going through the panel fitter anyway we can pretend to use any kind of mode. Sadly that means we can't reject user modes with the DBLSCAN flag until we know whether we're going to be using the panel's native mode or the user mode directly. Doing otherwise means X clients using xf86vidmode/xrandr will get a protocol error (and often self terminate as a result) when the kernel refuses to use the requested mode with the DBLSCAN flag. To undo the regression we'll move the DBLSCAN checks into the connector->mode_valid() and encoder->compute_config() hooks. Cc: stable@vger.kernel.org Cc: Vito Caputo <vcaputo@pengaru.com> Reported-by:
Vito Caputo <vcaputo@pengaru.com> Fixes: e995ca0b ("drm/i915: Provide a device level .mode_valid() hook") References: https://lkml.org/lkml/2018/5/21/715Signed-off-by:
Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=106804Tested-by:
Arkadiusz Miskiewicz <arekm@maven.pl> (cherry picked from commit e4dd27aa) Signed-off-by:
-
Chris Wilson authored
On allocation error, do not jump to the unwind handler that tries to free the error pointer. Reported-by:
Lionel Landwerlin <lionel.g.landwerlin@intel.com> Fixes: a89d1f92 ("drm/i915: Split i915_gem_timeline into individual timelines") Signed-off-by:
-
Chris Wilson authored
We special case the position of the batch within the GTT to prevent negative self-relocation deltas from underflowing. However, that restriction is being applied after a trial pin of the batch in its current position. Thus we are not rejecting an invalid location if the batch has been used before, leading to an assertion if we happen to need to rearrange the entire payload. In the worst case, this may cause a GPU hang on gen7 or perhaps missing state. References: https://bugs.freedesktop.org/show_bug.cgi?id=105720 Fixes: 2889caa9 ("drm/i915: Eliminate lots of iterations over the execobjects array") Signed-off-by:
-
Ben Skeggs authored
Ctxdmas for cursors from all heads are setup in the core channel, and due to us tracking allocated handles per-window, we were failing with -EEXIST on multiple-head setups trying to allocate duplicate handles. The cursor code is hardcoded to use the core channel vram ctxdma already, so just skip ctxdma allocation for cursor fbs to fix the issue. Fixes: 5bca1621 ("drm/nouveau/kms/nv50-: move fb ctxdma tracking into windows") Reported-by:
Adam Borowski <kilobyte@angband.pl> Signed-off-by:
Ben Skeggs <bskeggs@redhat.com>
-
- 18 Jun, 2018 1 commit
-
-
Paul Kocialkowski authored
This reverts commit 2c17a436. The offending commit triggers a run-time fault when accessing the panel element of the sun4i_tcon structure when no such panel is attached. It was apparently assumed in said commit that a panel is always used with the TCON. Although it is often the case, this is not always true. For instance a bridge might be used instead of a panel. This issue was discovered using an A13-OLinuXino, that uses the TCON in RGB mode for a simple DAC-based VGA bridge. Cc: stable@vger.kernel.org Signed-off-by:
Paul Kocialkowski <paul.kocialkowski@bootlin.com> Signed-off-by:
Maxime Ripard <maxime.ripard@bootlin.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180613081647.31183-1-paul.kocialkowski@bootlin.com
-
- 17 Jun, 2018 1 commit
-
-
Stefan Agner authored
The statement always evaluates to true since the struct fields are arrays. This has shown up as a warning when compiling with clang: warning: address of array 'desc->layout.xstride' will always evaluate to 'true' [-Wpointer-bool-conversion] Check for values in the first plane instead. Fixes: 1a396789 ("drm: add Atmel HLCDC Display Controller support") Cc: <stable@vger.kernel.org> Signed-off-by:Boris Brezillon <boris.brezillon@bootlin.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180617084826.31885-1-stefan@agner.ch
-
- 16 Jun, 2018 8 commits
-
-
Linus Torvalds authored
-
git://git.kernel.dk/linux-blockLinus Torvalds authored
Pull block fixes from Jens Axboe: "A collection of fixes that should go into -rc1. This contains: - bsg_open vs bsg_unregister race fix (Anatoliy) - NVMe pull request from Christoph, with fixes for regressions in this window, FC connect/reconnect path code unification, and a trace point addition. - timeout fix (Christoph) - remove a few unused functions (Christoph) - blk-mq tag_set reinit fix (Roman)" * tag 'for-linus-20180616' of git://git.kernel.dk/linux-block: bsg: fix race of bsg_open and bsg_unregister block: remov blk_queue_invalidate_tags nvme-fabrics: fix and refine state checks in __nvmf_check_ready nvme-fabrics: handle the admin-only case properly in nvmf_check_ready nvme-fabrics: refactor queue ready check blk-mq: remove blk_mq_tagset_iter nvme: remove nvme_reinit_tagset nvme-fc: fix nulling of queue data on reconnect nvme-fc: remove reinit_request routine blk-mq: don't time out requests again that are in the timeout handler nvme-fc: change controllers first connect to use reconnect path nvme: don't rely on the changed namespace list log nvmet: free smart-log buffer after use nvme-rdma: fix error flow during mapping request data nvme: add bio remapping tracepoint nvme: fix NULL pointer dereference in nvme_init_subsystem blk-mq: reinit q->tag_set_list entry only after grace period -
git://linuxtv.org/mchehab/experimentalLinus Torvalds authored
Pull documentation fixes from Mauro Carvalho Chehab: "This solves a series of broken links for files under Documentation, and improves a script meant to detect such broken links (see scripts/documentation-file-ref-check). The changes on this series are: - can.rst: fix a footnote reference; - crypto_engine.rst: Fix two parsing warnings; - Fix a lot of broken references to Documentation/*; - improve the scripts/documentation-file-ref-check script, in order to help detecting/fixing broken references, preventing false-positives. After this patch series, only 33 broken references to doc files are detected by scripts/documentation-file-ref-check" * tag 'docs-broken-links' of git://linuxtv.org/mchehab/experimental: (26 commits) fix a series of Documentation/ broken file name references Documentation: rstFlatTable.py: fix a broken reference ABI: sysfs-devices-system-cpu: remove a broken reference devicetree: fix a series of wrong file references devicetree: fix name of pinctrl-bindings.txt devicetree: fix some bindings file names MAINTAINERS: fix location of DT npcm files MAINTAINERS: fix location of some display DT bindings kernel-parameters.txt: fix pointers to sound parameters bindings: nvmem/zii: Fix location of nvmem.txt docs: Fix more broken references scripts/documentation-file-ref-check: check tools/*/Documentation scripts/documentation-file-ref-check: get rid of false-positives scripts/documentation-file-ref-check: hint: dash or underline scripts/documentation-file-ref-check: add a fix logic for DT scripts/documentation-file-ref-check: accept more wildcards at filenames scripts/documentation-file-ref-check: fix help message media: max2175: fix location of driver's companion documentation media: v4l: fix broken video4linux docs locations media: dvb: point to the location of the old README.dvb-usb file ... -
git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fsLinus Torvalds authored
Pull fsnotify updates from Jan Kara: "fsnotify cleanups unifying handling of different watch types. This is the shortened fsnotify series from Amir with the last five patches pulled out. Amir has modified those patches to not change struct inode but obviously it's too late for those to go into this merge window" * tag 'fsnotify_for_v4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs: fsnotify: add fsnotify_add_inode_mark() wrappers fanotify: generalize fanotify_should_send_event() fsnotify: generalize send_to_group() fsnotify: generalize iteration of marks by object type fsnotify: introduce marks iteration helpers fsnotify: remove redundant arguments to handle_event() fsnotify: use type id to identify connector object type
-
git://github.com/bzolnier/linuxLinus Torvalds authored
Pull fbdev updates from Bartlomiej Zolnierkiewicz: "There is nothing really major here, few small fixes, some cleanups and dead drivers removal: - mark omapfb drivers as orphans in MAINTAINERS file (Tomi Valkeinen) - add missing module license tags to omap/omapfb driver (Arnd Bergmann) - add missing GPIOLIB dependendy to omap2/omapfb driver (Arnd Bergmann) - convert savagefb, aty128fb & radeonfb drivers to use msleep & co. (Jia-Ju Bai) - allow COMPILE_TEST build for viafb driver (media part was reviewed by media subsystem Maintainer) - remove unused MERAM support from sh_mobile_lcdcfb and shmob-drm drivers (drm parts were acked by shmob-drm driver Maintainer) - remove unused auo_k190xfb drivers - misc cleanups (Souptick Joarder, Wolfram Sang, Markus Elfring, Andy Shevchenko, Colin Ian King)" * tag 'fbdev-v4.18' of git://github.com/bzolnier/linux: (26 commits) fb_omap2: add gpiolib dependency video/omap: add module license tags MAINTAINERS: make omapfb orphan video: fbdev: pxafb: match_string() conversion fixup video: fbdev: nvidia: fix spelling mistake: "scaleing" -> "scaling" video: fbdev: fix spelling mistake: "frambuffer" -> "framebuffer" video: fbdev: pxafb: Convert to use match_string() helper video: fbdev: via: allow COMPILE_TEST build video: fbdev: remove unused sh_mobile_meram driver drm: shmobile: remove unused MERAM support video: fbdev: sh_mobile_lcdcfb: remove unused MERAM support video: fbdev: remove unused auo_k190xfb drivers video: omap: Improve a size determination in omapfb_do_probe() video: sm501fb: Improve a size determination in sm501fb_probe() video: fbdev-MMP: Improve a size determination in path_init() video: fbdev-MMP: Delete an error message for a failed memory allocation in two functions video: auo_k190x: Delete an error message for a failed memory allocation in auok190x_common_probe() video: sh_mobile_lcdcfb: Delete an error message for a failed memory allocation in two functions video: sh_mobile_meram: Delete an error message for a failed memory allocation in sh_mobile_meram_probe() video: fbdev: sh_mobile_meram: Drop SUPERH platform dependency ... -
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfsLinus Torvalds authored
Pull AFS updates from Al Viro: "Assorted AFS stuff - ended up in vfs.git since most of that consists of David's AFS-related followups to Christoph's procfs series" * 'afs-proc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: afs: Optimise callback breaking by not repeating volume lookup afs: Display manually added cells in dynamic root mount afs: Enable IPv6 DNS lookups afs: Show all of a server's addresses in /proc/fs/afs/servers afs: Handle CONFIG_PROC_FS=n proc: Make inline name size calculation automatic afs: Implement network namespacing afs: Mark afs_net::ws_cell as __rcu and set using rcu functions afs: Fix a Sparse warning in xdr_decode_AFSFetchStatus() proc: Add a way to make network proc files writable afs: Rearrange fs/afs/proc.c to remove remaining predeclarations. afs: Rearrange fs/afs/proc.c to move the show routines up afs: Rearrange fs/afs/proc.c by moving fops and open functions down afs: Move /proc management functions to the end of the file
-
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfsLinus Torvalds authored
Pull compat updates from Al Viro: "Some biarch patches - getting rid of assorted (mis)uses of compat_alloc_user_space(). Not much in that area this cycle..." * 'work.compat' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: orangefs: simplify compat ioctl handling signalfd: lift sigmask copyin and size checks to callers of do_signalfd4() vmsplice(): lift importing iovec into vmsplice(2) and compat counterpart
-
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfsLinus Torvalds authored
Pull aio fixes from Al Viro: "Assorted AIO followups and fixes" * 'work.aio' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: eventpoll: switch to ->poll_mask aio: only return events requested in poll_mask() for IOCB_CMD_POLL eventfd: only return events requested in poll_mask() aio: mark __aio_sigset::sigmask const
-
- 15 Jun, 2018 1 commit
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds authored
Pull networking fixes from David Miller: 1) Various netfilter fixlets from Pablo and the netfilter team. 2) Fix regression in IPVS caused by lack of PMTU exceptions on local routes in ipv6, from Julian Anastasov. 3) Check pskb_trim_rcsum for failure in DSA, from Zhouyang Jia. 4) Don't crash on poll in TLS, from Daniel Borkmann. 5) Revert SO_REUSE{ADDR,PORT} change, it regresses various things including Avahi mDNS. From Bart Van Assche. 6) Missing of_node_put in qcom/emac driver, from Yue Haibing. 7) We lack checking of the TCP checking in one special case during SYN receive, from Frank van der Linden. 8) Fix module init error paths of mac80211 hwsim, from Johannes Berg. 9) Handle 802.1ad properly in stmmac driver, from Elad Nachman. 10) Must grab HW caps before doing quirk checks in stmmac driver, from Jose Abreu. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (81 commits) net: stmmac: Run HWIF Quirks after getting HW caps neighbour: skip NTF_EXT_LEARNED entries during forced gc net: cxgb3: add error handling for sysfs_create_group tls: fix waitall behavior in tls_sw_recvmsg tls: fix use-after-free in tls_push_record l2tp: filter out non-PPP sessions in pppol2tp_tunnel_ioctl() l2tp: reject creation of non-PPP sessions on L2TPv2 tunnels mlxsw: spectrum_switchdev: Fix port_vlan refcounting mlxsw: spectrum_router: Align with new route replace logic mlxsw: spectrum_router: Allow appending to dev-only routes ipv6: Only emit append events for appended routes stmmac: added support for 802.1ad vlan stripping cfg80211: fix rcu in cfg80211_unregister_wdev mac80211: Move up init of TXQs mac80211_hwsim: fix module init error paths cfg80211: initialize sinfo in cfg80211_get_station nl80211: fix some kernel doc tag mistakes hv_netvsc: Fix the variable sizes in ipsecv2 and rsc offload rds: avoid unenecessary cong_update in loop transport l2tp: clean up stale tunnel or session in pppol2tp_connect's error path ...
-
