Tegra chips have 4 or 5 identical UART modules embedded. UARTs C..E have
their MODEM-control signals tied off to a static state. However UARTs A
and B can optionally route those signals to/from package pins, depending
on the exact pinmux configuration.

When these signals are not routed to package pins, false interrupts may
trigger either temporarily, or permanently, all while not showing up in
the IIR; it will read as NO_INT. This will eventually lead to the UART
IRQ being disabled due to unhandled interrupts. When this happens, the
kernel may print e.g.:

    irq 68: nobody cared (try booting with the "irqpoll" option)

In order to prevent this, enable UART_BUG_NOMSR. This prevents
UART_IER_MSI from being enabled, which prevents the false interrupts
from triggering.

In practice, this is not needed under any of the following conditions:

* On Tegra chips after Tegra30, since the HW bug has apparently been
  fixed.

* On UARTs C..E since their MODEM control signals are tied to the correct
  static state which doesn't trigger the issue.

* On UARTs A..B if the MODEM control signals are routed out to package
  pins, since they will then carry valid signals.

However, we ignore these exceptions for now, since they are only relevant
if a board actually hooks up more than a 4-wire UART, and no currently
supported board does this. If we ever support a board that does, we can
refine the algorithm that enables UART_BUG_NOMSR to take those exceptions
into account, and/or read a flag from DT/... that indicates that the
board has hooked up and pinmux'd more than a 4-wire UART.

Reported-by: Olof Johansson <olof@lixom.net> # autotester
Cc: <stable@vger.kernel.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When using RX DMA, the driver won't pass any data to the uart layer
until the buffer is flipped. When the port is shutdown, the dma buffers
are unmapped, but the head and tail of the ring buffer are not reseted.
Since the serial console will keep the port open, this will only
present itself when the uart is not shared.

To reproduce the issue, with an unpatched driver, run a getty on /dev/ttyS0
with no serial console and exit. Getty will exit, and when the new one returns
you will be unable to log in.  If you hold down a key long enough to fill the
DMA buffer and flip it, you can then log in.
Signed-off-by: Mark Deneen <mdeneen@gmail.com>
Acked-by: Leilei Zhao <leilei.zhao@atmel.com>
[nicolas.ferre@atmel.com: adapt to mainline kernel, handle !DMA case]
Cc: <stable@vger.kernel.org> # v3.12
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The _remove callback could be called when a tasklet is scheduled. tasklet_kill
was called inside the function in order to free up any scheduled tasklets.
However it was called after uart_remove_one_port which destroys tty references
needed in the port for atmel_tasklet_func.
Simply putting the tasklet_kill at the start of the function will prevent this
conflict.
Signed-off-by: Marek Roszko <mark.roszko@gmail.com>
Acked-by: Leilei Zhao <leilei.zhao@atmel.com>
Cc: <stable@vger.kernel.org> # v3.12
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Interrupts were being cleaned up late in the shutdown handler, it is possible
that an interrupt can occur and schedule a tasklet that runs after the port is
cleaned up. There is a null dereference due to this race condition with the
following stacktrace:

[<c02092b0>] (atmel_tasklet_func+0x514/0x814) from [<c001fd34>] (tasklet_action+0x70/0xa8)
[<c001fd34>] (tasklet_action+0x70/0xa8) from [<c001f60c>] (__do_softirq+0x90/0x144)
[<c001f60c>] (__do_softirq+0x90/0x144) from [<c001fa18>] (irq_exit+0x40/0x4c)
[<c001fa18>] (irq_exit+0x40/0x4c) from [<c000e298>] (handle_IRQ+0x64/0x84)
[<c000e298>] (handle_IRQ+0x64/0x84) from [<c000d6c0>] (__irq_svc+0x40/0x50)
[<c000d6c0>] (__irq_svc+0x40/0x50) from [<c0208060>] (atmel_rx_dma_release+0x88/0xb8)
[<c0208060>] (atmel_rx_dma_release+0x88/0xb8) from [<c0209740>] (atmel_shutdown+0x104/0x160)
[<c0209740>] (atmel_shutdown+0x104/0x160) from [<c0205e8c>] (uart_port_shutdown+0x2c/0x38)
Signed-off-by: Marek Roszko <mark.roszko@gmail.com>
Acked-by: Leilei Zhao <leilei.zhao@atmel.com>
Cc: <stable@vger.kernel.org> # v3.12
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In rx dma-callback it calls tasklet_schedule, if the tasklet
be scheduled after all the dma-callback in the rx dma channel,
current check condition in the tasklet will not do fetch dma
buffer into tty because tx_issued is equal with tx_completed,
so as timeout tasklet does.

so we check whether we should fetch the whole dma buffer into
tty according to the status of transactions in rx dma channel.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

this patch provides PM entry of uart_ops, then drop clk enable and
disable because serial core will do it.

the patch also fixes the issue that uart hang in resume caused by
not-enabled clock.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

use SET_SYSTEM_SLEEP_PM_OPS to initialize suspend/resume functions
instead of legacy suspend and resume entries of platform_driver.
this will add hibernation support automatically as suspend to disk
entries are also set.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This helps increasing build testing coverage.
To do this, read{write}_relaxed() functions was be replaced with
simple read{write}() variants. Potential "uninitialized variable"
warnings was be fixed if driver compiled without MFD_SYSCON.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch replace custom handling of IrDA feature with N_IRDA
line discipline, so IrDA mode can be used with irtty driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The four variants of the synclink driver use the same code in their
open() callback to wait for a port in process of being closed,
using interruptible_sleep_on, which is racy and going away soon.

Making things worse, these functions hold the BTM while doing so,
which means that if we ever enter this code path, we cannot actually
continue since the other thread that is in process of closing the
port can no longer get the BTM.

This addresses both issues by using wait_event_interruptible_tty()
instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

interruptible_sleep_on is generally problematic and we want to get
rid of it. In case of TIOCMIWAIT, that race is actually in user
space and does not get fixed since we can only detect changes after
entering the ioctl handler, but it removes one more caller.

This instance can not be trivially replaced with wait_event, so
I chose to open-code the wait loop using prepare_to_wait/finish_wait.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>.  Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We need the tty fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull ARM SoC fixes from Olof Johansson:
 "Much smaller batch of fixes this week.

  Biggest one is a revert of an OMAP display change that removed some
  non-DT pinmux code that was still needed for 3.13 to get DSI displays
  to work.

  There's also a fix that resolves some misdescribed GPIO controller
  resources on shmobile.  The rest are mostly smaller fixes, a couple of
  MAINTAINERS updates, etc"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  Revert "ARM: OMAP2+: Remove legacy mux code for display.c"
  MAINTAINERS: Add keystone clock drivers
  MAINTAINERS: Add keystone git tree information
  ARM: s3c64xx: dt: Fix boot failure due to double clock initialization
  ARM: shmobile: r8a7790: Fix GPIO resources in DTS
  irqchip: renesas-intc-irqpin: Fix register bitfield shift calculation
  ARM: shmobile: lager: phy fixup needs CONFIG_PHYLIB

Pull firewire fixlet from Stefan Richter:
 "A one-liner to reenable WRITE SAME over SBP-2 like in v3.8...v3.12.
  Buggy targets which could malfunction when being subjected to this
  command are already sufficiently protected by a scsi_level check in sd
  + SCSI core"

* tag 'firewire-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
  firewire: sbp2: bring back WRITE SAME support

Pull SCSI target fixes from Nicholas Bellinger:
 "Mostly minor items this time around, the most notable being a FILEIO
  backend change to enforce hw_max_sectors based upon the current
  block_size to address a bug where large sized I/Os (> 1M) where being
  rejected"

* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
  qla2xxx: Fix scsi_host leak on qlt_lport_register callback failure
  target: Remove extra percpu_ref_init
  target/file: Update hw_max_sectors based on current block_size
  iser-target: Move INIT_WORK setup into isert_create_device_ib_res
  iscsi-target: Fix incorrect np->np_thread NULL assignment
  qla2xxx: Fix schedule_delayed_work() for target timeout calculations
  iser-target: fix error return code in isert_create_device_ib_res()
  iscsi-target: Fix-up all zero data-length CDBs with R/W_BIT set
  target: Remove write-only stats fields and lock from struct se_node_acl
  iscsi-target: return -EINVAL on oversized configfs parameter

Pull AIO leak fixes from Ben LaHaise:
 "I've put these two patches plus Linus's change through a round of
  tests, and it passes millions of iterations of the aio numa
  migratepage test, as well as a number of repetitions of a few simple
  read and write tests.

  The first patch fixes the memory leak Kent introduced, while the
  second patch makes aio_migratepage() much more paranoid and robust"

* git://git.kvack.org/~bcrl/aio-next:
  aio/migratepages: make aio migrate pages sane
  aio: fix kioctx leak introduced by "aio: Fix a trinity splat"

Since commit 36bc08cc ("fs/aio: Add support to aio ring pages
migration") the aio ring setup code has used a special per-ring backing
inode for the page allocations, rather than just using random anonymous
pages.

However, rather than remembering the pages as it allocated them, it
would allocate the pages, insert them into the file mapping (dirty, so
that they couldn't be free'd), and then forget about them.  And then to
look them up again, it would mmap the mapping, and then use
"get_user_pages()" to get back an array of the pages we just created.

Now, not only is that incredibly inefficient, it also leaked all the
pages if the mmap failed (which could happen due to excessive number of
mappings, for example).

So clean it all up, making it much more straightforward.  Also remove
some left-overs of the previous (broken) mm_populate() usage that was
removed in commit d6c355c7 ("aio: fix race in ring buffer page
lookup introduced by page migration support") but left the pointless and
now misleading MAP_POPULATE flag around.
Tested-and-acked-by: Benjamin LaHaise <bcrl@kvack.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The arbitrary restriction on page counts offered by the core
migrate_page_move_mapping() code results in rather suspicious looking
fiddling with page reference counts in the aio_migratepage() operation.
To fix this, make migrate_page_move_mapping() take an extra_count parameter
that allows aio to tell the code about its own reference count on the page
being migrated.

While cleaning up aio_migratepage(), make it validate that the old page
being passed in is actually what aio_migratepage() expects to prevent
misbehaviour in the case of races.
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>

e34ecee2 reworked the percpu reference
counting to correct a bug trinity found.  Unfortunately, the change lead
to kioctxes being leaked because there was no final reference count to
put.  Add that reference count back in to fix things.
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>
Cc: stable@vger.kernel.org

Commit 1bf49dd4 ("./Makefile: export initial ramdisk compression
config option") started setting the INITRD_COMPRESS environment variable
depending on which decompression models the kernel had available.

That is completely broken.

For example, we by default have CONFIG_RD_LZ4 enabled, and are able to
decompress such an initrd, but the user tools to *create* such an initrd
may not be availble.  So trying to tell dracut to generate an
lz4-compressed image just because we can decode such an image is
completely inappropriate.

Cc: J P <ppandit@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jan Beulich <JBeulich@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull xfs bugfixes from Ben Myers:
 "This contains fixes for some asserts
   related to project quotas, a memory leak, a hang when disabling group or
   project quotas before disabling user quotas, Dave's email address, several
   fixes for the alignment of file allocation to stripe unit/width geometry, a
   fix for an assertion with xfs_zero_remaining_bytes, and the behavior of
   metadata writeback in the face of IO errors.

   Details:
   - fix memory leak in xfs_dir2_node_removename
   - fix quota assertion in xfs_setattr_size
   - fix quota assertions in xfs_qm_vop_create_dqattach
   - fix for hang when disabling group and project quotas before
     disabling user quotas
   - fix Dave Chinner's email address in MAINTAINERS
   - fix for file allocation alignment
   - fix for assertion in xfs_buf_stale by removing xfsbdstrat
   - fix for alignment with swalloc mount option
   - fix for "retry forever" semantics on IO errors"

* tag 'xfs-for-linus-v3.13-rc5' of git://oss.sgi.com/xfs/xfs:
  xfs: abort metadata writeback on permanent errors
  xfs: swalloc doesn't align allocations properly
  xfs: remove xfsbdstrat error
  xfs: align initial file allocations correctly
  MAINTAINERS: fix incorrect mail address of XFS maintainer
  xfs: fix infinite loop by detaching the group/project hints from user dquot
  xfs: fix assertion failure at xfs_setattr_nonsize
  xfs: fix false assertion at xfs_qm_vop_create_dqattach
  xfs: fix memory leak in xfs_dir2_node_removename

Commit 597d795a ('mm: do not allocate page->ptl dynamically, if
spinlock_t fits to long') restructures some allocators that are compiled
even if USE_SPLIT_PTLOCKS arn't used.  It results in compilation
failure:

  mm/memory.c:4282:6: error: 'struct page' has no member named 'ptl'
  mm/memory.c:4288:12: error: 'struct page' has no member named 'ptl'

Add in the missing ifdef.

Fixes: 597d795a ('mm: do not allocate page->ptl dynamically, if spinlock_t fits to long')
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull ARC fix from Vineet Gupta:
 "Fix busted syscall table due to unistd header inclusion issue"

* tag 'arc-fixes-for-3.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
  ARC: Allow conditional multiple inclusion of uapi/asm/unistd.h

Pull arm64 ptrace fix from Catalin Marinas.

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: ptrace: avoid using HW_BREAKPOINT_EMPTY for disabled events

Some pstore backing devices use on board flash as persistent
storage. These have limited numbers of write cycles so it
is a poor idea to use them from high frequency operations.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge tag 'dmaengine-fixes-3.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/dmaengine

Pull dmaengine fixes from Dan Williams:

 - deprecation of net_dma to be removed in 3.14

 - crash regression fix in pl330 from the dmaengine_unmap rework

 - crash regression fix for any channel running raid ops without
   CONFIG_ASYNC_TX_DMA from dmaengine_unmap

 - memory leak regression in mv_xor from dmaengine_unmap

 - build warning regressions in mv_xor, fsldma, ppc4xx, txx9, and
   at_hdmac from dmaengine_unmap

 - sleep in atomic regression in dma_async_memcpy_pg_to_pg

 - new fix in mv_xor for handling channel initialization failures

* tag 'dmaengine-fixes-3.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/dmaengine:
  net_dma: mark broken
  dma: pl330: ensure DMA descriptors are zero-initialised
  dmaengine: fix sleep in atomic
  dmaengine: mv_xor: fix oops when channels fail to initialise
  dma: mv_xor: Use dmaengine_unmap_data for the self-tests
  dmaengine: fix enable for high order unmap pools
  dma: fix build warnings in txx9
  dmatest: fix build warning on mips
  dma: fix fsldma build warnings
  dma: fix build warnings in ppc4xx
  dmaengine: at_hdmac: remove unused function
  dma: mv_xor: remove mv_desc_get_dest_addr()

Pull KVM fixes from Paolo Bonzini:
 "The PPC folks had a large amount of changes queued for 3.13, and now
  they are fixing the bugs"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: PPC: Book3S HV: Don't drop low-order page address bits
  powerpc: book3s: kvm: Don't abuse host r2 in exit path
  powerpc/kvm/booke: Fix build break due to stack frame size warning
  KVM: PPC: Book3S: PR: Enable interrupts earlier
  KVM: PPC: Book3S: PR: Make svcpu -> vcpu store preempt savvy
  KVM: PPC: Book3S: PR: Export kvmppc_copy_to|from_svcpu
  KVM: PPC: Book3S: PR: Don't clobber our exit handler id
  powerpc: kvm: fix rare but potential deadlock scene
  KVM: PPC: Book3S HV: Take SRCU read lock around kvm_read_guest() call
  KVM: PPC: Book3S HV: Make tbacct_lock irq-safe
  KVM: PPC: Book3S HV: Refine barriers in guest entry/exit
  KVM: PPC: Book3S HV: Fix physical address calculations

In struct page we have enough space to fit long-size page->ptl there,
but we use dynamically-allocated page->ptl if size(spinlock_t) is larger
than sizeof(int).

It hurts 64-bit architectures with CONFIG_GENERIC_LOCKBREAK, where
sizeof(spinlock_t) == 8, but it easily fits into struct page.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

there is an overflow in the code :
cyz_polling_cycle = (arg * HZ) / 1000,
the multiplicator arg comes from user, so it may be an overflow if
arg is a big number. And the value of cyc_polling_cycle will be
wrong when it is used next time.
Reported-by: Qixue Xiao <xiaoqixue_1@163.com>
Suggested-by: Yongjian Xu <xuyongjiande@gmail.com>
Suggested-by: Yu Chen <chyyuu@gmail.com>
Signed-off-by: Qixue Xiao <xiaoqixue_1@163.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit 81c0a2bb ("mm: page_alloc: fair zone allocator policy") meant
to bring aging fairness among zones in system, but it was overzealous
and badly regressed basic workloads on NUMA systems.

Due to the way kswapd and page allocator interacts, we still want to
make sure that all zones in any given node are used equally for all
allocations to maximize memory utilization and prevent thrashing on the
highest zone in the node.

While the same principle applies to NUMA nodes - memory utilization is
obviously improved by spreading allocations throughout all nodes -
remote references can be costly and so many workloads prefer locality
over memory utilization.  The original change assumed that
zone_reclaim_mode would be a good enough predictor for that, but it
turned out to be as indicative as a coin flip.

Revert the NUMA aspect of the fairness until we can find a proper way to
make it configurable and agree on a sane default.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Mel Gorman <mgorman@suse.de>
Cc: <stable@kernel.org> # 3.12
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This reverts commit 73f038b8.  The NUMA behaviour of this patch is
less than ideal.  An alternative approch is to interleave allocations
only within local zones which is implemented in the next patch.

Cc: stable@vger.kernel.org
Signed-off-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Sasha Levin found a NULL pointer dereference that is due to a missing
page table lock, which in turn is due to the pmd entry in question being
a transparent huge-table entry.

The code - introduced in commit 1998cc04 ("mm: make
madvise(MADV_WILLNEED) support swap file prefetch") - correctly checks
for this situation using pmd_none_or_trans_huge_or_clear_bad(), but it
turns out that that function doesn't work correctly.

pmd_none_or_trans_huge_or_clear_bad() expected that pmd_bad() would
trigger if the transparent hugepage bit was set, but it doesn't do that
if pmd_numa() is also set. Note that the NUMA bit only gets set on real
NUMA machines, so people trying to reproduce this on most normal
development systems would never actually trigger this.

Fix it by removing the very subtle (and subtly incorrect) expectation,
and instead just checking pmd_trans_huge() explicitly.
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Acked-by: Andrea Arcangeli <aarcange@redhat.com>
[ Additionally remove the now stale test for pmd_trans_huge() inside the
  pmd_bad() case - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge tag 'renesas-fixes-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes

From Simon Horman:
Renesas ARM based SoC fixes for v3.13

* r8a7790 (R-Car H1) SoC
  - Correct GPIO resources in DT.

    This problem has been present since GPIOs were added to the r8a7790 SoC
    by f98e10c8 ("ARM: shmobile: r8a7790: Add GPIO controller
    devices to device tree") in v3.12-rc1.

* irqchip renesas-intc-irqpin
  - Correct register bitfield shift calculation

    This bug has been present since the renesas-intc-irqpin driver was
    introduced by 44358048 ("irqchip: Renesas INTC External IRQ pin
    driver") in v3.10-rc1

* Lager board
  - Do not build the phy fixup unless CONFIG_PHYLIB is enabled

    This problem was introduced by 48c8b96f

* tag 'renesas-fixes-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  ARM: shmobile: r8a7790: Fix GPIO resources in DTS
  irqchip: renesas-intc-irqpin: Fix register bitfield shift calculation
  ARM: shmobile: lager: phy fixup needs CONFIG_PHYLIB
Signed-off-by: Kevin Hilman <khilman@linaro.org>

Patch queue for 3.13 - 2013-12-18

This fixes some grave issues we've only found after 3.13-rc1:

  - Make the modularized HV/PR book3s kvm work well as modules
  - Fix some race conditions
  - Fix compilation with certain compilers (booke)
  - Fix THP for book3s_hv
  - Fix preemption for book3s_pr

Alexander Graf (4):
      KVM: PPC: Book3S: PR: Don't clobber our exit handler id
      KVM: PPC: Book3S: PR: Export kvmppc_copy_to|from_svcpu
      KVM: PPC: Book3S: PR: Make svcpu -> vcpu store preempt savvy
      KVM: PPC: Book3S: PR: Enable interrupts earlier

Aneesh Kumar K.V (1):
      powerpc: book3s: kvm: Don't abuse host r2 in exit path

Paul Mackerras (5):
      KVM: PPC: Book3S HV: Fix physical address calculations
      KVM: PPC: Book3S HV: Refine barriers in guest entry/exit
      KVM: PPC: Book3S HV: Make tbacct_lock irq-safe
      KVM: PPC: Book3S HV: Take SRCU read lock around kvm_read_guest() call
      KVM: PPC: Book3S HV: Don't drop low-order page address bits

Scott Wood (1):
      powerpc/kvm/booke: Fix build break due to stack frame size warning

pingfan liu (1):
      powerpc: kvm: fix rare but potential deadlock scene

Pull Xen bugfixes from Konrad Rzeszutek Wilk:
 - Fix balloon driver for auto-translate guests (PVHVM, ARM) to not use
   scratch pages.
 - Fix block API header for ARM32 and ARM64 to have proper layout
 - On ARM when mapping guests, stick on PTE_SPECIAL
 - When using SWIOTLB under ARM, don't call swiotlb functions twice
 - When unmapping guests memory and if we fail, don't return pages which
   failed to be unmapped.
 - Grant driver was using the wrong address on ARM.

* tag 'stable/for-linus-3.13-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  xen/balloon: Seperate the auto-translate logic properly (v2)
  xen/block: Correctly define structures in public headers on ARM32 and ARM64
  arm: xen: foreign mapping PTEs are special.
  xen/arm64: do not call the swiotlb functions twice
  xen: privcmd: do not return pages which we have failed to unmap
  XEN: Grant table address, xen_hvm_resume_frames, is a phys_addr not a pfn

Merge tag 'trace-fixes-v3.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace

Pull ftrace fix from Steven Rostedt:
 "This fixes a long standing bug in the ftrace profiler.  The problem is
  that the profiler only initializes the online CPUs, and not possible
  CPUs.  This causes issues if the user takes CPUs online or offline
  while the profiler is running.

  If we online a CPU after starting the profiler, we lose all the trace
  information on the CPU going online.

  If we offline a CPU after running a test and start a new test, it will
  not clear the old data from that CPU.

  This bug causes incorrect data to be reported to the user if they
  online or offline CPUs during the profiling"

* tag 'trace-fixes-v3.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  ftrace: Initialize the ftrace profiler for each possible cpu

Merge tag 'omap-for-v3.13/display-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

I accidentally removed some mux code for omap4 that I thought was
dead code as omap4 has been booting with device tree only since
v3.10. Turns out I also removed some display related mux code,
so let's revert that except for the dead code parts.

* tag 'omap-for-v3.13/display-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (439 commits)
  Revert "ARM: OMAP2+: Remove legacy mux code for display.c"
  +Linux 3.13-rc4

Merge tag 'keystone/maintainer-file' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into fixes

From Santosh Shilimkar:
Couple of updates to MAINTAINERS file for Keystone

- Add git tree information
- Add clock drivers entry

* tag 'keystone/maintainer-file' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
  MAINTAINERS: Add keystone clock drivers
  MAINTAINERS: Add keystone git tree information
Signed-off-by: Kevin Hilman <khilman@linaro.org>