- 07 Jan, 2024 12 commits
-
-
Swee Leong Ching authored
Enable per DMA channel interrupt that uses shared peripheral interrupt (SPI), so only per channel TX and RX intr (TI/RI) are handled by TX/RX ISR without calling common interrupt ISR. Signed-off-by:
Teoh Ji Sheng <ji.sheng.teoh@intel.com> Signed-off-by:
Swee Leong Ching <leong.ching.swee@intel.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Swee Leong Ching authored
Enable TX/RX channel interrupt registration for MAC that interrupts CPU through shared peripheral interrupt (SPI). Per channel interrupts and interrupt-names are registered through, Eg: 4 tx and 4 rx channels: interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>; <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>; <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>; <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>; <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "dma_tx0", "dma_tx1", "dma_tx2", "dma_tx3", "dma_rx0", "dma_rx1", "dma_rx2", "dma_rx3"; Signed-off-by: -
Swee Leong Ching authored
There is no support for per DMA channel interrupt for non-MSI platform, where the MAC's per channel interrupt hooks up to interrupt controller(GIC) through shared peripheral interrupt(SPI) to handle interrupt from TX/RX transmit channel. This patch generalize the existing MSI ISR to also support non-MSI platform. Signed-off-by:
-
Swee Leong Ching authored
Add dt-bindings for per channel irq. Signed-off-by:
Rohan G Thomas <rohan.g.thomas@intel.com> Signed-off-by:
-
David S. Miller authored
Christian Marangi says: ==================== net: phy: at803x: even more generalization This is part 3 of at803x required patches to split the PHY driver in more specific PHY Family driver. While adding support for a new PHY Family qca807x it was notice lots of similarities with the qca808x cdt function. Hence this series is done to make things easier in the future when qca807x PHY will be submitted. Changes v4: - Fix Smatch warning Changes v3: - Rebase on top of net-next Changes v2: - Address request from Russell in a previous series on cdt get status improvement ==================== Signed-off-by: -
Christian Marangi authored
Make read_status more generic in preparation on moving it to shared library as other PHY Family Driver will have the exact same implementation. The only specific part was a check for AR8031/33 if 1000basex was used. The check is moved to a dedicated function specific for those PHYs. Signed-off-by:
Christian Marangi <ansuelsmth@gmail.com> Reviewed-by:
Simon Horman <horms@kernel.org> Signed-off-by:
-
Christian Marangi authored
QCA808x PHY Family supports Cable Diagnostic Test also for Cross Pair Short. Add all the define to make enable and support these additional tests. Cross Short test was previously disabled by default, this is now changed and enabled by default. In this mode, the mask changed a bit and length is shifted based on the fault condition. Signed-off-by:
-
Christian Marangi authored
Refactor qca808x cable test get status function to remove code duplication and clean things up. The same logic is applied to each pair hence it can be generalized and moved to a common function. Signed-off-by:
-
Christian Marangi authored
Generalize cable test fault length function since they all base on the same magic values (already reverse engineered to understand the meaning of it) to have consistenct values on every PHY. Signed-off-by:
-
Zhengchao Shao authored
In fib_nl2rule(), 'err' variable has been set to -EINVAL during declaration, and no need to set the 'err' variable to -EINVAL again. So, remove it. Signed-off-by:
Zhengchao Shao <shaozhengchao@huawei.com> Reviewed-by:
David Ahern <dsahern@kernel.org> Signed-off-by:
-
Pedro Tammela authored
Instead of using two bools derived from a flags passed as arguments to the parent function of tc_action_load_ops, just pass the flags itself to tc_action_load_ops to simplify its parameters. Reviewed-by:
Jiri Pirko <jiri@nvidia.com> Signed-off-by:
Pedro Tammela <pctammela@mojatatu.com> Acked-by:
Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by:
-
Christophe JAILLET authored
ida_alloc() and ida_free() should be preferred to the deprecated ida_simple_get() and ida_simple_remove(). This is less verbose. Note that the upper bound of ida_alloc_range() is inclusive while the one of ida_simple_get() was exclusive. So NFP_FL_LAG_GROUP_MAX has been decreased by 1. It now better watch the comment stating that "1 to 31 are valid". The only other user of NFP_FL_LAG_GROUP_MAX has been updated accordingly in nfp_fl_lag_put_unprocessed(). Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by:
-
- 06 Jan, 2024 5 commits
-
-
Ahmed Zaki authored
RXFH input_xfrm currently has three supported values: 0 (clear all), symmetric_xor and NO_CHANGE. Reject any other value sent from user-space. Fixes: 13e59344 ("net: ethtool: add support for symmetric-xor RSS hash") Suggested-by:
Jakub Kicinski <kuba@kernel.org> Signed-off-by:
Ahmed Zaki <ahmed.zaki@intel.com> Link: https://lore.kernel.org/r/20240104212653.394424-1-ahmed.zaki@intel.comSigned-off-by:
-
Benjamin Poirier authored
The expression "source ../lib.sh" added to net/forwarding/lib.sh in commit 25ae948b ("selftests/net: add lib.sh") does not work for tests outside net/forwarding which source net/forwarding/lib.sh (1). It also does not work in some cases where only a subset of tests are exported (2). Avoid the problems mentioned above by replacing the faulty expression with a copy of the content from net/lib.sh which is used by files under net/forwarding. A more thorough solution which avoids duplicating content between net/lib.sh and net/forwarding/lib.sh has been posted here: https://lore.kernel.org/netdev/20231222135836.992841-1-bpoirier@nvidia.com/ The approach in the current patch is a stopgap solution to avoid submitting large changes at the eleventh hour of this development cycle. Example of problem 1) tools/testing/selftests/drivers/net/bonding$ ./dev_addr_lists.sh ./net_forwarding_lib.sh: line 41: ../lib.sh: No such file or directory TEST: bonding cleanup mode active-backup [ OK ] TEST: bonding cleanup mode 802.3ad [ OK ] TEST: bonding LACPDU multicast address to slave (from bond down) [ OK ] TEST: bonding LACPDU multicast address to slave (from bond up) [ OK ] An error message is printed but since the test does not use functions from net/lib.sh, the test results are not affected. Example of problem 2) tools/testing/selftests$ make install TARGETS="net/forwarding" tools/testing/selftests$ cd kselftest_install/net/forwarding/ tools/testing/selftests/kselftest_install/net/forwarding$ ./pedit_ip.sh veth{0..3} lib.sh: line 41: ../lib.sh: No such file or directory TEST: ping [ OK ] TEST: ping6 [ OK ] ./pedit_ip.sh: line 135: busywait: command not found TEST: dev veth1 ingress pedit ip src set 198.51.100.1 [FAIL] Expected to get 10 packets, but got . ./pedit_ip.sh: line 135: busywait: command not found TEST: dev veth2 egress pedit ip src set 198.51.100.1 [FAIL] Expected to get 10 packets, but got . ./pedit_ip.sh: line 135: busywait: command not found TEST: dev veth1 ingress pedit ip dst set 198.51.100.1 [FAIL] Expected to get 10 packets, but got . ./pedit_ip.sh: line 135: busywait: command not found TEST: dev veth2 egress pedit ip dst set 198.51.100.1 [FAIL] Expected to get 10 packets, but got . ./pedit_ip.sh: line 135: busywait: command not found TEST: dev veth1 ingress pedit ip6 src set 2001:db8:2::1 [FAIL] Expected to get 10 packets, but got . ./pedit_ip.sh: line 135: busywait: command not found TEST: dev veth2 egress pedit ip6 src set 2001:db8:2::1 [FAIL] Expected to get 10 packets, but got . ./pedit_ip.sh: line 135: busywait: command not found TEST: dev veth1 ingress pedit ip6 dst set 2001:db8:2::1 [FAIL] Expected to get 10 packets, but got . ./pedit_ip.sh: line 135: busywait: command not found TEST: dev veth2 egress pedit ip6 dst set 2001:db8:2::1 [FAIL] Expected to get 10 packets, but got . In this case, the test results are affected. Fixes: 25ae948b ("selftests/net: add lib.sh") Suggested-by:
Ido Schimmel <idosch@nvidia.com> Suggested-by:
Petr Machata <petrm@nvidia.com> Reviewed-by:
Benjamin Poirier <bpoirier@nvidia.com> Reviewed-by:
Hangbin Liu <liuhangbin@gmail.com> Link: https://lore.kernel.org/r/20240104141109.100672-1-bpoirier@nvidia.comSigned-off-by:
-
https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-nextJakub Kicinski authored
Daniel Borkmann says: ==================== pull-request: bpf-next 2024-01-05 We've added 40 non-merge commits during the last 2 day(s) which contain a total of 73 files changed, 1526 insertions(+), 951 deletions(-). The main changes are: 1) Fix a memory leak when streaming AF_UNIX sockets were inserted into multiple sockmap slots/maps, from John Fastabend. 2) Fix gotol in s390 BPF JIT with large offsets, from Ilya Leoshkevich. 3) Fix reattachment branch in bpf_tracing_prog_attach() and reject the request if there is no valid attach_btf, from Jiri Olsa. 4) Remove deprecated bpfilter kernel leftovers given the project is developed in user space (https://github.com/facebook/bpfilter), from Quentin Deslandes. 5) Relax tracing BPF program recursive attach rules given right now it is not possible to create tracing program call cycles, from Dmitrii Dolgov. 6) Fix excessive memory consumption for the bpf_global_percpu_ma for systems with a large number of CPUs, from Yonghong Song. 7) Small x86 BPF JIT cleanup to reuse emit_nops instead of open-coding memcpy of x86_nops, from Leon Hwang. 8) Follow-up for libbpf to support __arg_ctx global function argument tag semantics to complement the merged kernel side, from Andrii Nakryiko. 9) Introduce "volatile compare" macros for BPF selftests in order to make the latter more robust against compiler optimization, from Alexei Starovoitov. 10) Small simplification in verifier's size checking of helper accesses along with additional selftests, from Andrei Matei. * tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (40 commits) selftests/bpf: Test re-attachment fix for bpf_tracing_prog_attach bpf: Fix re-attachment branch in bpf_tracing_prog_attach selftests/bpf: Add test for recursive attachment of tracing progs bpf: Relax tracing prog recursive attach rules bpf, x86: Use emit_nops to replace memcpy x86_nops selftests/bpf: Test gotol with large offsets selftests/bpf: Double the size of test_loader log s390/bpf: Fix gotol with large offsets bpfilter: remove bpfilter bpf: Remove unnecessary cpu == 0 check in memalloc selftests/bpf: add __arg_ctx BTF rewrite test selftests/bpf: add arg:ctx cases to test_global_funcs tests libbpf: implement __arg_ctx fallback logic libbpf: move BTF loading step after relocation step libbpf: move exception callbacks assignment logic into relocation step libbpf: use stable map placeholder FDs libbpf: don't rely on map->fd as an indicator of map being created libbpf: use explicit map reuse flag to skip map creation steps libbpf: make uniform use of btf__fd() accessor inside libbpf selftests/bpf: Add a selftest with > 512-byte percpu allocation size ... ==================== Link: https://lore.kernel.org/r/20240105170105.21070-1-daniel@iogearbox.netSigned-off-by:
-
Vadim Fedorenko authored
The fb.com domain is going to be deprecated. Use personal one for kernel contributions. Signed-off-by:
Vadim Fedorenko <vadfed@fb.com> Reviewed-by:
-
Eric Dumazet authored
geneve updates dev->stats fields locklessly. Adopt DEV_STATS_INC() to avoid races. Signed-off-by:
Eric Dumazet <edumazet@google.com> Reviewed-by:
-
- 05 Jan, 2024 23 commits
-
-
Jakub Kicinski authored
Richard Gobert says: ==================== net: gro: reduce extension header parsing overhead This series attempts to reduce the parsing overhead of IPv6 extension headers in GRO and GSO, by removing extension header specific code and enabling the frag0 fast path. The following changes were made: - Removed some unnecessary HBH conditionals by adding HBH offload to inet6_offloads - Added a utility function to support frag0 fast path in ipv6_gro_receive - Added selftests for IPv6 packets with extension headers in GRO v2: https://lore.kernel.org/netdev/127b8199-1cd4-42d7-9b2b-875abaad93fe@gmail.com/ v1: https://lore.kernel.org/netdev/f4eff69d-3917-4c42-8c6b-d09597ac4437@gmail.com/ ==================== Link: https://lore.kernel.org/r/ac6fb684-c00e-449c-92c3-99358a927ade@gmail.comSigned-off-by:
-
Richard Gobert authored
Currently there is no test which checks that IPv6 extension header packets successfully coalesce. This commit adds a test, which verifies two IPv6 packets with HBH extension headers do coalesce, and another test which checks that packets with different extension header data do not coalesce in GRO. I changed the receive socket filter to accept a packet with one extension header. This change exposed a bug in the fragment test -- the old BPF did not accept the fragment packet. I updated correct_num_packets in the fragment test accordingly. Signed-off-by:
Richard Gobert <richardbgobert@gmail.com> Reviewed-by:
Willem de Bruijn <willemb@google.com> Link: https://lore.kernel.org/r/69282fed-2415-47e8-b3d3-34939ec3eb56@gmail.comSigned-off-by:
-
Richard Gobert authored
The existing code always pulls the IPv6 header and sets the transport offset initially. Then optionally again pulls any extension headers in ipv6_gso_pull_exthdrs and sets the transport offset again on return from that call. skb->data is set at the start of the first extension header before calling ipv6_gso_pull_exthdrs, and must disable the frag0 optimization because that function uses pskb_may_pull/pskb_pull instead of skb_gro_ helpers. It sets the GRO offset to the TCP header with skb_gro_pull and sets the transport header. Then returns skb->data to its position before this block. This commit introduces a new helper function - ipv6_gro_pull_exthdrs - which is used in ipv6_gro_receive to pull ipv6 ext headers instead of ipv6_gso_pull_exthdrs. Thus, there is no modification of skb->data, all operations use skb_gro_* helpers, and the frag0 fast path can be taken for IPv6 packets with ext headers. Signed-off-by:
-
Richard Gobert authored
This commit adds net_offload to IPv6 Hop-by-Hop extension headers (as it is done for routing and dstopts) since it is supported in GSO and GRO. This allows to remove specific HBH conditionals in GSO and GRO when pulling and parsing an incoming packet. Signed-off-by:
-
Jakub Kicinski authored
W=1 builds now warn if module is built without a MODULE_DESCRIPTION(). Add descriptions to all the CAIF sub-modules. Link: https://lore.kernel.org/r/20240104144855.1320993-1-kuba@kernel.orgSigned-off-by:
-
Jakub Kicinski authored
W=1 builds now warn if module is built without a MODULE_DESCRIPTION(). Add description to net/packet/af_packet.c Acked-by:
-
Jakub Kicinski authored
W=1 builds now warn if module is built without a MODULE_DESCRIPTION(). Add descriptions to all the DSA tag modules. The descriptions are copy/pasted Kconfig names, with s/^Tag/DSA tag/. Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Reviewed-by:
Florian Fainelli <florian.fainelli@broadcom.com> Reviewed-by:
Vladimir Oltean <vladimir.oltean@nxp.com> Acked-by:
Arun Ramadoss <arun.ramadoss@microchip.com> Acked-by:
Arınç ÜNAL <arinc.unal@arinc9.com> Acked-by:
Kurt Kanzenbach <kurt@linutronix.de> Link: https://lore.kernel.org/r/20240104143759.1318137-1-kuba@kernel.orgSigned-off-by:
-
Jakub Kicinski authored
W=1 builds now warn if module is built without a MODULE_DESCRIPTION(). Add descriptions to all the ATM modules and drivers. Link: https://lore.kernel.org/r/20240104143737.1317945-1-kuba@kernel.orgSigned-off-by:
-
Jakub Kicinski authored
Jiri Pirko says: ==================== dpll: expose fractional frequency offset value to user Allow to expose pin fractional frequency offset value over new DPLL generic netlink attribute. Add an op to get the value from the driver. Implement this new op in mlx5 driver. ==================== Link: https://lore.kernel.org/r/20240103132838.1501801-1-jiri@resnulli.usSigned-off-by:
-
Jiri Pirko authored
Implement ffo_get() pin op filling it up to MSEED.frequency_diff value. Signed-off-by:
Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com> Acked-by:
Vadim Fedorenko <vadim.fedorenko@linux.dev> Acked-by:
-
Jiri Pirko authored
Instead of passing separate args, introduce struct mlx5_dpll_synce_status to hold the values obtained by mlx5_dpll_synce_status_get(). Signed-off-by:
-
Jiri Pirko authored
Add a new netlink attribute to expose fractional frequency offset value for a pin. Add an op to get the value from the driver. Signed-off-by:
-
David S. Miller authored
Vladimir Oltean says: ==================== ds->user_mii_bus cleanup (part 1) There are some drivers which assign ds->user_mii_bus when they don't really need its specific functionality, aka non-OF based dsa_user_phy_connect(). There was some confusion regarding the fact that yes, this is why ds->user_mii_bus really exists, so I've started a cleanup series which aims to eliminate the usage of ds->user_mii_bus from drivers when there is nothing to gain from it. Today's drivers are lantiq_gswip, qca8k and bcm_sf2. The work is not done here, but a "part 2" may or may not come, depending on other priorities. All patches were only compile-tested. ==================== Signed-off-by: -
Vladimir Oltean authored
There used to be a of_node_put(priv->master_mii_dn) call in bcm_sf2_mdio_unregister(), which was accidentally deleted in commit 6ca80638 ("net: dsa: Use conduit and user terms"). But it's not needed - we don't need to hold a reference on the "brcm,unimac-mdio" OF node for that long, since we don't do anything with it. We can release it as soon as we finish bcm_sf2_mdio_register(). Also reduce "if (err && dn)" to just "if (err)". We know "dn", aka the former priv->master_mii_dn, is non-NULL. Otherwise, of_mdio_find_bus(dn) would not have been able to find the bus behind "brcm,unimac-mdio". Signed-off-by:
Alvin Šipraga <alsi@bang-olufsen.dk> Reviewed-by:
Luiz Angelo Daros de Luca <luizluca@gmail.com> Signed-off-by:
-
Vladimir Oltean authored
The bcm_sf2 driver does something strange. Instead of calling of_mdiobus_register() with an OF node argument, it manually assigns the bus->dev->of_node and then calls the non-OF mdiobus_register(). This circumvents some code from __of_mdiobus_register() from running, which sets the auto-scan mask, parses some device tree properties, etc. I'm going to go out on a limb and say that the OF node isn't, in fact, needed at all, and can be removed. The MDIO diversion as initially implemented in commit 461cd1b0 ("net: dsa: bcm_sf2: Register our slave MDIO bus") looked quite different than it is now, after commit 771089c2 ("net: dsa: bcm_sf2: Ensure that MDIO diversion is used"). Initially, it made sense, as bcm_sf2 was registering another set of driver ops for the "brcm,unimac-mdio" OF node. But now, it deletes all phandles, which makes "phy-handle"s unable to find PHYs, which means that it always goes through the OF-unaware dsa_user_phy_connect(). Signed-off-by:
-
Vladimir Oltean authored
Accessed either through priv->dev or ds->dev, it is the same device structure. Keep a single variable which holds a reference to it, and use it consistently. Signed-off-by:
-
Vladimir Oltean authored
__of_mdiobus_register() already calls __mdiobus_register() if the OF node provided as argument is NULL. We can take advantage of that and simplify the 2 code path, calling devm_of_mdiobus_register() only once for both cases. Signed-off-by:
-
Vladimir Oltean authored
To simplify reasoning about why the DSA framework provides the ds->user_mii_bus functionality, drivers should only use it if they need to. The qca8k driver appears to also use it simply as storage for a pointer, which is not a good enough reason to make the core much more difficult to follow. ds->user_mii_bus is useful for only 2 cases: 1. The driver probes on platform_data (no OF) 2. The driver probes on OF, but there is no OF node for the MDIO bus. It is unclear if case (1) is supported with qca8k. It might not be: the driver might crash when of_device_get_match_data() returns NULL and then it dereferences priv->info without NULL checking. Anyway, let us limit the ds->user_mii_bus usage only to the above cases, and not assign it when an OF node is present. The bus->phy_mask assignment follows along with the movement, because __of_mdiobus_register() overwrites this bus field anyway. The value set by the driver only matters for the non-OF code path. Signed-off-by:
-
Vladimir Oltean authored
Currently the driver calls the non-OF devm_mdiobus_register() rather than devm_of_mdiobus_register() for this case, but it seems to rather be a confusing coincidence, and not a real use case that needs to be supported. If the device tree says status = "disabled" for the MDIO bus, we shouldn't need an MDIO bus at all. Instead, just exit as early as possible and do not call any MDIO API. Signed-off-by:
-
Vladimir Oltean authored
of_get_child_by_name() gives us an OF node with an elevated refcount, which should be dropped when we're done with it. This is so that, if (of_node_check_flag(node, OF_DYNAMIC)) is true, the node's memory can eventually be freed. There are 2 distinct paths to be considered in qca8k_mdio_register(): - devm_of_mdiobus_register() succeeds: since commit 3b73a7b8 ("net: mdio_bus: add refcounting for fwnodes to mdiobus"), the MDIO core treats this well. - devm_of_mdiobus_register() or anything up to that point fails: it is the duty of the qca8k driver to release the OF node. This change addresses the second case by making sure that the OF node reference is not leaked. The "mdio" node may be NULL, but of_node_put(NULL) is safe. Signed-off-by:
-
Vladimir Oltean authored
If the "lantiq,xrx200-mdio" child has status = "disabled", the MDIO bus creation should be avoided. Use of_device_is_available() to check for that, and take advantage of 2 facts: - of_device_is_available(NULL) returns false - of_node_put(NULL) is a no-op Signed-off-by:
-
Vladimir Oltean authored
This driver does not need any of the functionalities that make ds->user_mii_bus special. Those use cases are listed here: https://lore.kernel.org/netdev/20231221174746.hylsmr3f7g5byrsi@skbuf/ It just makes use of ds->user_mii_bus only as storage for its own MDIO bus, which otherwise has no connection to the framework. This is because: - the gswip driver only probes on OF: it fails if of_device_get_match_data() returns NULL - when the child OF node of the MDIO bus is absent, no MDIO bus is registered at all, not even by the DSA framework. In order for that to have happened, the gswip driver would have needed to provide ->phy_read() and ->phy_write() in struct dsa_switch_ops, which it does not. We can break the connection between the gswip driver and the DSA framework and still preserve the same functionality. Since commit 3b73a7b8 ("net: mdio_bus: add refcounting for fwnodes to mdiobus"), MDIO buses take ownership of the OF node handled to them, and release it on their own. The gswip driver no longer needs to do this. Combine that with devres, and we no longer need to keep track of anything for teardown purposes. Signed-off-by:
-
Vladimir Oltean authored
__of_mdiobus_register(), called right next, overwrites the phy_mask we just configured on the bus, so this is redundant and confusing. Delete it. Signed-off-by:
-
