If runtime PM is not enabled in the kernel config, pm_runtime_get_sync()
will always return 1 and pm_runtime_put_sync() will always return
-ENOSYS. pm_runtime_get_sync() returning 1 presents no problem to the
driver, but -ENOSYS from pm_runtime_put_sync() causes the driver to
print a warning.

One option would be to ignore errors returned by pm_runtime_put_sync()
totally, as they only say that the call was unable to put the hardware
into suspend mode.

However, I chose to ignore the returned -ENOSYS explicitly, and print a
warning for other errors, as I think we should get notified if the HW
failed to go to suspend properly.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Jassi Brar <jaswinder.singh@linaro.org>
Cc: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>

The current way how omapdss handles system suspend and resume is that
omapdss device (a platform device, which is not part of the device
hierarchy of the DSS HW devices, like DISPC and DSI, or panels.) uses
the suspend and resume callbacks from platform_driver to handle system
suspend. It does this by disabling all enabled panels on suspend, and
resuming the previously disabled panels on resume.

This presents a few problems.

One is that as omapdss device is not related to the panel devices or the
DSS HW devices, there's no ordering in the suspend process. This means
that suspend could be first ran for DSS HW devices and panels, and only
then for omapdss device. Currently this is not a problem, as DSS HW
devices and panels do not handle suspend.

Another, more pressing problem, is that when suspending or resuming, the
runtime PM functions return -EACCES as runtime PM is disabled during
system suspend. This causes the driver to print warnings, and operations
to fail as they think that they failed to bring up the HW.

This patch changes the omapdss suspend handling to use PM notifiers,
which are called before suspend and after resume. This way we have a
normally functioning system when we are suspending and resuming the
panels.

This patch, I believe, creates a problem that somebody could enable or
disable a panel between PM_SUSPEND_PREPARE and the system suspend, and
similarly the other way around in resume. I choose to ignore the problem
for now, as it sounds rather unlikely, and if it happens, it's not
fatal.

In the long run the system suspend handling of omapdss and panels should
be thought out properly. The current approach feels rather hacky.
Perhaps the panel drivers should handle system suspend, or the users of
omapdss (omapfb, omapdrm) should handle system suspend.

Note that after this patch we could probably revert
0eaf9f52 (OMAPDSS: use sync versions of
pm_runtime_put). But as I said, this patch may be temporary, so let's
leave the sync version still in place.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: Jassi Brar <jaswinder.singh@linaro.org>
Tested-by: Jassi Brar <jaswinder.singh@linaro.org>
Tested-by: Joe Woodward <jw@terrafix.co.uk>
Signed-off-by: Archit Taneja <archit@ti.com>
[fts: fixed 2 brace coding style issues]
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>

Divider value can be zero and it makes division by zero
from debug message in s3c_fb_calc_pixclk; therefore, it
should be fixed.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>

All bits of SHADOWCON register should be cleared when clearing
hardware window registers; however, some bits of SHADOWCON register
are not cleared previously.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>

This driver requires both SPI and I2C to build.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>

Long delays need to use mdelay on architectures such as ARM
that cannot compute long timeouts in udelay.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>

The frame buffer console needs at least one font to be built into
the kernel, so add the necessary Kconfig magic to guarantee that
one of the available font is always on. If a user accidentally
disables all fonts manually, the 8x16 font will be selected
anyway.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>

No symbol can be exported when the section is discarded - the only
solution I could think of is not to mark symbols as __devexit
when they are exported.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>

__devexit functions are discarded when CONFIG_HOTPLUG
is not set, so the symbol needs to be referenced carefully.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>

This patch removes a call to the deprecated simple_strtoul function
and simplifies the code by replacing two function calls with one
call to kstrtouint_from_user.

-Simplify the adv7393_write_proc function by replacing the
 simple_strtoul and copy_from_user calls with one call
 to kstrtouint_from_user.

-Change the count parameter from unsigned long to size_t as
 this is the type that the kstrtouint_from_user function expects.
 (size_t is what will be passed to the adv7393_write_proc function
 by the proc write handler function proc_file_write anyway)
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>

Small fixes for omapdss driver. Most importantly, fixes a build problem when
debugfs or omapdss debug support is turned off, and fixes a suspend related
crash.

The omapdss arch initialization code registers all the output devices as
omap_devices. However, DPI and SDI are not proper omap_devices, as they
do not have any corresponding HWMOD. This leads to crashes or problems
when the platform code tries to use omap_device functions for DPI and
SDI devices.

One such crash was reported by John Stultz <johnstul@us.ibm.com>:

[   18.756835] Unable to handle kernel NULL pointer dereference at
virtual addr8
[   18.765319] pgd = ea6b8000
[   18.768188] [00000018] *pgd=aa942831, *pte=00000000, *ppte=00000000
[   18.774749] Internal error: Oops: 17 [#1] SMP ARM
[   18.779663] Modules linked in:
[   18.782836] CPU: 0    Not tainted  (3.5.0-rc1-dirty #456)
[   18.788482] PC is at _od_resume_noirq+0x1c/0x78
[   18.793212] LR is at _od_resume_noirq+0x6c/0x78
[   18.797943] pc : [<c00307ec>]    lr : [<c003083c>]    psr: 20000113
[   18.797943] sp : ec3abe80  ip : ec3abdb8  fp : 00000006
[   18.809936] r10: ec1148b8  r9 : c08a48f0  r8 : c00307d0
[   18.815368] r7 : 00000000  r6 : 00000000  r5 : ec114800  r4 :
ec114808
[   18.822174] r3 : 00000000  r2 : 00000000  r1 : ec154fe8  r0 :
00000006
[   18.829010] Flags: nzCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM
Segment user
[   18.836456] Control: 10c5387d  Table: aa6b804a  DAC: 00000015
[   18.842437] Process sh (pid: 1139, stack limit = 0xec3aa2f0)
[   18.848358] Stack: (0xec3abe80 to 0xec3ac000)

DPI and SDI can be plain platform_devices. This patch changes the
registration from omap_device_register() to platform_device_add().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: John Stultz <johnstul@us.ibm.com>
Tested-by: Jean Pihet <jean.pihet@newoldbits.com>

In function dsi_compute_interleave_lp(), the escape clock/LP clock time period
is calculated incorrectly. The escape clock/LP clock is calculated as:

LP Clock(Hz) = DSI_FCLK(Hz) / lp_clk_div

Since we are calculating the time period of LP clock, the LP clock divider
should be multiplied with the time period of DSI_FCLK.

Calculating incorrect value of txclkesc results in incorrect calculation of LP
interleaving parameters, it also creates a possibility of a divide by zero
error.
Reported-by: Sureshkumar Manimuthu <mail2msuresh@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

pm_runtime_put_sync() in dss_runtime_put() returns -EBUSY when any child
of dss is still enabled. This happens, for example, when a display
output is enabled and one dumps the clocks via debugfs. This causes
dss_runtime_get & put to be called.

While I couldn't find anything about this in the documentation and it
wasn't immediately clear from runtime_pm code, it looks to me that
pm_runtime_put_sync() returns -EBUSY to inform that things went fine,
but the device could not be turned off as there are still child devices
that are enabled. This is not a problem.

This patch skips the WARN_ON if pm_runtime_put_sync() returns -EBUSY.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

This patch fixes a warning:

drivers/video/omap2/displays/panel-taal.c: In function
‘taal_num_errors_show’:
drivers/video/omap2/displays/panel-taal.c:529: warning: ‘errors’ may be
used uninitialized in this function
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

If CONFIG_DEBUG_FS or CONFIG_OMAP2_DSS_DEBUG_SUPPORT is disabled, the
build fails:

drivers/video/omap2/dss/core.c:197:50: error: static declaration of
'dss_debugfs_create_file' follows non-static declaration
drivers/video/omap2/dss/dss.h:166:5: note: previous declaration of
'dss_debugfs_create_file' was here

This patch fixes the dummy dss_debugfs_create_file() so that the driver
builds.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

This patch fixes the cleanup code of the bfin_adv7393_fb_probe
function.

1) The resources were not freed in the order that we allocated them
   so we call dma_free_coherent() before it was allocated.
2) The labels weren't in the right place which also meant that we
   freed resources that weren't allocated.
3) We should free gpio_free(P_IDENT(P_PPI0_FS3)) before returning.
4) Lets change the label names into something more meaningful.
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Acked-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>

This patch reduces delay time when configuring video setting,
which is helpful to reduce wakeup time during resume.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>

The sw reset should be called prioir to enabling sw defined function,
according to datasheet.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>

The devm_ functions allocate memory that is released when a driver
detaches. This makes the code smaller and a bit simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>

This function is called with a potential NULL pointer in
picolcd_init_framebuffer() and it causes a static checker warning.  This
used to handle NULL pointers when the picolcd code was written, but a
couple months later we added the "info->apertures" dereference.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>

Omapdss driver changes for 3.5 merge window.

Lots of normal development commits, but perhaps most notable changes are:

* HDMI rework to properly decouple the HDMI audio part from the HDMI video part.
* Restructure omapdss core driver so that it's possible to implement device
  tree support. This included changing how platform data is passed to the
  drivers, changing display device registration and improving the panel driver's
  ability to configure the underlying video output interface.
* Basic support for DSI packet interleaving

genirq requires that the IRQ requests that do not provided a handler to
use the IRQF_ONESHOT flag. This is to prevent situations in which the irq line
is reenabled while the interrupt is still asserted. While this situation may
not happen in edge type interrupts, genirq still requires to use IRQF_ONESHOT.

Also, remove the IRQF_DISABLED as the flag is now a NOOP and has been
deprecated.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

The VENC interfaces uses it's venc_set_timing() function to take in a new set
of timings. If the panel is disabled, it does not disable and re-enable the
interface. Currently, the manager timings are applied in venc_power_on(), these
are not called by set_timings if the panel is disabled. When checking overlay
and manager data, the DSS driver uses the last applied manager timings, and not
the timings held by omap_dss_device struct. Hence, there is a need to apply the
new manager timings even if the panel is disabled.

Apply the manager timings if the VENC panel is disabled.

This is similar to the commit below which fixed the same issue for HDMI/DPI
interfaces:

fcc36619Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

DSS2 driver uses the timings in manager's private data to check the validity of
overlay and manager infos written by the user. For VENC interface, we divide the
Y resolution by half when writing to the DISPC_DIGIT_SIZE register as the
content is interlaced. However, the height of the manager/display with respect
to the content shown through VENC still remains the same.

The VENC driver divides the y_res parameter in omap_video_timings by half, and
then applies the configuration. This leads to manager's private data storing
the wrong Y resolution. Hence, overlay related checks fail.

Ensure that manager's private data stores the original timings, and the Y
resolution is halved only when we write to the DISPC register. This is a hack,
the proper solution would be to pass some sort of interlace parameter which
makes the call whether we should divide y_res or not.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

TILER is a block in OMAP4's DMM which lets DSS fetch frames in a rotated manner.
Physical memory can be mapped to a portion of OMAP's system address space called
TILER address space. The TILER address space is split into 8 views. Each view
represents a rotated or mirrored form of the mapped physical memory. When a
DISPC overlay's base address is programmed to one of these views, the TILER
fetches the pixels according to the orientation of the view. A view is further
split into 4 containers, each container holds elements of a particular size.
Rotation can be achieved at the granularity of elements in the container. For
more information on TILER, refer to the Memory Subsytem section in OMAP4 TRM.
Rotation type TILER has been added which is used to exploit the capabilities of
these 8 views for performing various rotations.

When fetching from addresses mapped to TILER space, the DISPC DMA can fetch
pixels in either 1D or 2D bursts. The fetch depends on which TILER container we
are accessing. Accessing 8, 16 and 32 bit sized containers requires 2D bursts,
and page mode sized containers require 1D bursts.

The DSS2 user is expected to provide the Tiler address of the view that it is
interested in. This is passed to the paddr and p_uv_addr parameters in
omap_overlay_info. It is also expected to provide the stride value based on the
view's orientation and container type, this should be passed to the screen_width
parameter of omap_overlay_info. In calc_tiler_rotation_offset screen_width is
used to calculate the required row_inc for DISPC. x_predecim and y_predecim are
also used to calculate row_inc and pix_inc thereby adding predecimation support
for TILER.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

If CONFIG_BUG is not enabled, BUG() does not stop the execution. Many
places in code expect the execution to stop, and this causes compiler
warnings about uninitialized variables and returning from a non-void
function without a return value.

This patch fixes the warnings by initializing the variables and
returning properly after BUG() lines. However, the behaviour is still
undefined after the BUG, but this is the choice the user makes when
using CONFIG_BUG=n.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

If CONFIG_BUG is not enabled, BUG() does not stop the execution. Many
places in code expect the execution to stop, and this causes compiler
warnings about uninitialized variables and returning from a non-void
function without a return value.

This patch fixes the warnings by initializing the variables and
returning properly after BUG() lines. However, the behaviour is still
undefined after the BUG, but this is the choice the user makes when
using CONFIG_BUG=n.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

If CONFIG_BUG is not enabled, BUG() does not stop the execution. Many
places in code expect the execution to stop, and this causes compiler
warnings about uninitialized variables and returning from a non-void
function without a return value.

This patch fixes the warnings by initializing the variables and
returning properly after BUG() lines. However, the behaviour is still
undefined after the BUG, but this is the choice the user makes when
using CONFIG_BUG=n.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Commit 05dd0f53 ("OMAPDSS: DISPC: Update
Accumulator configuration for chroma plane") adds
dispc_ovl_set_accu_uv() function that sets the accu, but the function
only handles YUV and NV12 modes, and BUGs otherwise.

The patch also adds a call to the function, but unfortunately the place
of call was such that the mode could be other than YUV or NV12, thus
crashing the driver.

This patchs moves the call to a slightly later spot, at which point only
YUV and NV12 modes are handled.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Chandrabhanu Mahapatra <cmahapatra@ti.com>

There is a problem related to DSS FIFO thresholds and power management
on OMAP3. It seems that when the full PM hits in, we get underflows. The
core reason is unknown, but after experiments it looks like only
particular FIFO thresholds work correctly.

This bug is related to an earlier patch, which added special FIFO
threshold configuration for OMAP3, because DSI command mode output
didn't work with the normal threshold configuration.

However, as the above work-around worked fine for other output types
also, we currently always configure thresholds in this special way on
OMAP3. In theory there should be negligible difference with this special
way and the standard way. The first paragraph explains what happens in
practice.

This patch changes the driver to use the special threshold configuration
only when the output is a manual update display on OMAP3. This does
include RFBI displays also, and although it hasn't been tested (no
boards using RFBI) I suspect the similar behaviour is present there
also, as the DISPC side should work similarly for DSI command mode and
RFBI.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Joe Woodward <jw@terrafix.co.uk>

DSI supports interleaving of command mode packets during the HSA, HFP, HBP and
BLLP blanking intervals in a video mode stream. This is useful as a user may
want to read or change the configuration of a panel without stopping the video
stream.

On OMAP DSI, we can queue HS or LP command mode packets in the TX FIFO, and
the DSI HW takes care of interleaving this data during the one of the blanking
intervals. The DSI HW needs to be programmed with the maximum amount of data
that can be interleaved in a particular blanking period. A blanking period
cannot be used to send command mode data for it's complete duration, there is
some amount of time required for the DSI data and clock lanes to transition
to the desired LP or HS state.

Based on the state of the lanes at the beginning and end of the blanking period,
we have different scenarios, with each scenario having a different value of time
required to transition to HS or LP. Refer to the section 'Interleaving Mode' in
OMAP TRM for more info on the scenarios and the equations to calculate the time
required for HS or LP transitions.

We use the scenarios which takes the maximum time for HS or LP transition, this
gives us the minimum amount of time that can be used to interleave command mode
data. The amount of data that can be sent during this minimum time is calculated
for command mode packets both in LP and HS. These are written to the registers
DSI_VM_TIMING4 to DSI_VM_TIMING6.

The calculations don't take into account the time required of transmitting BTA
when doing a DSI read, or verifying if a DSI write went through correctly. Until
these latencies aren't considered, the behaviour of DSI is unpredictable when
a BTA is interleaved during a blanking period. Enhancement of these calculations
is a TODO item.

The calculations are derived from DSI parameter calculation tools written by
Sebastien Fagard <s-fagard@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

DISPC has two accumulator registers DISPC_VIDp_ACCU_0 and DISPC_VIDp_ACCU_1 each
with horizontal and vertical bit fields. The bit fields can take values in the
range of -1024 to 1023. Based on bit field values DISPC decides on which one out
of 8 phases the filtering starts. DISPC_VIDp_ACCU_0 is used for progressive
output and for interlaced output both DISPC_VIDp_ACCU_0 and DISPC_VIDp_ACCU_1
are used.

The current accumulator values in DISPC scaling logic for chroma plane takes
default values for all color modes and rotation types. So, the horizontal and
vertical up and downsampling accumulator bit field values have been updated for
better performance.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

The THRESHOLDS register configures thresholds for two interrupts, but
these interrupts are not used in the DIU driver.  An early version of the
driver may have used the "lines before vsync" interrupt, which requires
the LS_BF_VS of THRESHOLDS to be initialized.

Unfortunately, the initialization of this register does not do a
read-modify-write to set only LS_BF_VS.  On the MPC8610, the value
written is correct.  On other chips, like the P1022, the value overwrites
some reserved bits.  This results in a performance drop on the P1022.

Since the default value is acceptable as-is on all SOCs, we should just
avoid touching this register.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>

This patch adds panel_reverse variable to support reversed s6e8ax0 panel
type.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>

Rework the interrupt handler so the RX_DONE, FIFO_EMPTY interrupts are
properly detected. This prevents missing the interrupts when there are
other bits set in the INTSRC register than just RX_DONE and FIFO_EMPTY.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>

Make sure all resources are initialized before interrupt handler is
registered. Pass full platform device name to request_irq() so it
can be distinguished which device has requested an interrupt in cases
there are multiple instances in the system.

Also enable voltage regulators regardless of they have been enabled
by bootloader or not, to make sure other drivers using same regulators
don't disable them unexpectedly.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>

Use proper PM ops from struct dev_pm_ops rather than the deprecated ones.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>

Latest SuperH HDMI uses not only HDMI Core Register (HTOP0)
but also HDMI Control Register (HTOP1).
This patch adds HDMI Control Register support.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>

Latest SuperH HDMI allows 32bit access only.
But the data is 8bit. So, we can keep compatibility by switching 8/32 bit access.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>