- 23 Jan, 2016 31 commits
-
-
Ben Hutchings authored
commit 5377adb0 upstream. usb_parse_ss_endpoint_companion() now decodes the burst multiplier correctly in order to check that it's <= 3, but still uses the wrong expression if warning that it's > 3. Fixes: ff30cbc8 ("usb: Use the USB_SS_MULT() macro to get the ...") Signed-off-by:
Ben Hutchings <ben@decadent.org.uk> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Alexey Khoroshilov authored
commit f9fa1887 upstream. qset_fill_page_list() do not check for dma mapping errors. Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by:
Alexey Khoroshilov <khoroshilov@ispras.ru> Signed-off-by:
-
Alan Stern authored
commit ad87e032 upstream. Some USB device / host controller combinations seem to have problems with Link Power Management. For example, Steinar found that his xHCI controller wouldn't handle bandwidth calculations correctly for two video cards simultaneously when LPM was enabled, even though the bus had plenty of bandwidth available. This patch introduces a new quirk flag for devices that should remain disabled for LPM, and creates quirk entries for Steinar's devices. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Reported-by:
Steinar H. Gunderson <sgunderson@bigfoot.com> Signed-off-by:
-
Konstantin Shkolnyy authored
commit 7c90e610 upstream. CP2110 ID (0x10c4, 0xea80) doesn't belong here because it's a HID and completely different from CP210x devices. Signed-off-by:
Konstantin Shkolnyy <konstantin.shkolnyy@gmail.com> Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Jonas Jonsson authored
commit a0e80fbd upstream. The flash loader has been seen on a Telit UE910 modem. The flash loader is a bit special, it presents both an ACM and CDC Data interface but only the latter is useful. Unless a magic string is sent to the device it will disappear and the regular modem device appears instead. Signed-off-by:
Jonas Jonsson <jonas@ludd.ltu.se> Tested-by:
Daniele Palmas <dnlplm@gmail.com> Signed-off-by:
-
Jonas Jonsson authored
commit f33a7f72 upstream. Some modems, such as the Telit UE910, are using an Infineon Flash Loader utility. It has two interfaces, 2/2/0 (Abstract Modem) and 10/0/0 (CDC Data). The latter can be used as a serial interface to upgrade the firmware of the modem. However, that isn't possible when the cdc-acm driver takes control of the device. The following is an explanation of the behaviour by Daniele Palmas during discussion on linux-usb. "This is what happens when the device is turned on (without modifying the drivers): [155492.352031] usb 1-3: new high-speed USB device number 27 using ehci-pci [155492.485429] usb 1-3: config 1 interface 0 altsetting 0 endpoint 0x81 has an invalid bInterval 255, changing to 11 [155492.485436] usb 1-3: New USB device found, idVendor=058b, idProduct=0041 [155492.485439] usb 1-3: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [155492.485952] cdc_acm 1-3:1.0: ttyACM0: USB ACM device This is the flashing device that is caught by the cdc-acm driver. Once the ttyACM appears, the application starts sending a magic string (simple write on the file descriptor) to keep the device in flashing mode. If this magic string is not properly received in a certain time interval, the modem goes on in normal operative mode: [155493.748094] usb 1-3: USB disconnect, device number 27 [155494.916025] usb 1-3: new high-speed USB device number 28 using ehci-pci [155495.059978] usb 1-3: New USB device found, idVendor=1bc7, idProduct=0021 [155495.059983] usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [155495.059986] usb 1-3: Product: 6 CDC-ACM + 1 CDC-ECM [155495.059989] usb 1-3: Manufacturer: Telit [155495.059992] usb 1-3: SerialNumber: 359658044004697 [155495.138958] cdc_acm 1-3:1.0: ttyACM0: USB ACM device [155495.140832] cdc_acm 1-3:1.2: ttyACM1: USB ACM device [155495.142827] cdc_acm 1-3:1.4: ttyACM2: USB ACM device [155495.144462] cdc_acm 1-3:1.6: ttyACM3: USB ACM device [155495.145967] cdc_acm 1-3:1.8: ttyACM4: USB ACM device [155495.147588] cdc_acm 1-3:1.10: ttyACM5: USB ACM device [155495.154322] cdc_ether 1-3:1.12 wwan0: register 'cdc_ether' at usb-0000:00:1a.7-3, Mobile Broadband Network Device, 00:00:11:12:13:14 Using the cdc-acm driver, the string, though being sent in the same way than using the usb-serial-simple driver (I can confirm that the data is passing properly since I used an hw usb sniffer), does not make the device to stay in flashing mode." Signed-off-by:
-
Junxiao Bi authored
commit 8f1eb487 upstream. New created file's mode is not masked with umask, and this makes umask not work for ocfs2 volume. Fixes: 702e5bc6 ("ocfs2: use generic posix ACL infrastructure") Signed-off-by:
Junxiao Bi <junxiao.bi@oracle.com> Cc: Gang He <ghe@suse.com> Cc: Mark Fasheh <mfasheh@suse.de> Cc: Joel Becker <jlbec@evilplan.org> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Jeff Layton authored
commit c812012f upstream. If we pass in an empty nfs_fattr struct to nfs_update_inode, it will (correctly) not update any of the attributes, but it then clears the NFS_INO_INVALID_ATTR flag, which indicates that the attributes are up to date. Don't clear the flag if the fattr struct has no valid attrs to apply. Reviewed-by:
Steve French <steve.french@primarydata.com> Signed-off-by:
Jeff Layton <jeff.layton@primarydata.com> Signed-off-by:
Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by:
-
Benjamin Coddington authored
commit c68a027c upstream. If clp->cl_cb_ident is zero, then nfs_cb_idr_remove_locked() skips removing it when the nfs_client is freed. A decoding or server bug can then find and try to put that first nfs_client which would lead to a crash. Signed-off-by:
Benjamin Coddington <bcodding@redhat.com> Fixes: d6870312 ("nfs4client: convert to idr_alloc()") Signed-off-by:
-
Stefan Richter authored
commit 100ceb66 upstream. Reported by Clifford and Craig for JMicron OHCI-1394 + SDHCI combo controllers: Often or even most of the time, the controller is initialized with the message "added OHCI v1.10 device as card 0, 4 IR + 0 IT contexts, quirks 0x10". With 0 isochronous transmit DMA contexts (IT contexts), applications like audio output are impossible. However, OHCI-1394 demands that at least 4 IT contexts are implemented by the link layer controller, and indeed JMicron JMB38x do implement four of them. Only their IsoXmitIntMask register is unreliable at early access. With my own JMB381 single function controller I found: - I can reproduce the problem with a lower probability than Craig's. - If I put a loop around the section which clears and reads IsoXmitIntMask, then either the first or the second attempt will return the correct initial mask of 0x0000000f. I never encountered a case of needing more than a second attempt. - Consequently, if I put a dummy reg_read(...IsoXmitIntMaskSet) before the first write, the subsequent read will return the correct result. - If I merely ignore a wrong read result and force the known real result, later isochronous transmit DMA usage works just fine. So let's just fix this chip bug up by the latter method. Tested with JMB381 on kernel 3.13 and 4.3. Since OHCI-1394 generally requires 4 IT contexts at a minium, this workaround is simply applied whenever the initial read of IsoXmitIntMask returns 0, regardless whether it's a JMicron chip or not. I never heard of this issue together with any other chip though. I am not 100% sure that this fix works on the OHCI-1394 part of JMB380 and JMB388 combo controllers exactly the same as on the JMB381 single- function controller, but so far I haven't had a chance to let an owner of a combo chip run a patched kernel. Strangely enough, IsoRecvIntMask is always reported correctly, even though it is probed right before IsoXmitIntMask. Reported-by: Clifford Dunn Reported-by:
Craig Moore <craig.moore@qenos.com> Signed-off-by:
Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by:
-
Daeho Jeong authored
commit 4327ba52 upstream. If a EXT4 filesystem utilizes JBD2 journaling and an error occurs, the journaling will be aborted first and the error number will be recorded into JBD2 superblock and, finally, the system will enter into the panic state in "errors=panic" option. But, in the rare case, this sequence is little twisted like the below figure and it will happen that the system enters into panic state, which means the system reset in mobile environment, before completion of recording an error in the journal superblock. In this case, e2fsck cannot recognize that the filesystem failure occurred in the previous run and the corruption wouldn't be fixed. Task A Task B ext4_handle_error() -> jbd2_journal_abort() -> __journal_abort_soft() -> __jbd2_journal_abort_hard() | -> journal->j_flags |= JBD2_ABORT; | | __ext4_abort() | -> jbd2_journal_abort() | | -> __journal_abort_soft() | | -> if (journal->j_flags & JBD2_ABORT) | | return; | -> panic() | -> jbd2_journal_update_sb_errno() Tested-by:
Hobin Woo <hobin.woo@samsung.com> Signed-off-by:
Daeho Jeong <daeho.jeong@samsung.com> Signed-off-by:
Theodore Ts'o <tytso@mit.edu> Signed-off-by:
-
Lukas Czerner authored
commit 6934da92 upstream. There is a use-after-free possibility in __ext4_journal_stop() in the case that we free the handle in the first jbd2_journal_stop() because we're referencing handle->h_err afterwards. This was introduced in 9705acd6 and it is wrong. Fix it by storing the handle->h_err value beforehand and avoid referencing potentially freed handle. Fixes: 9705acd6Signed-off-by:
Lukas Czerner <lczerner@redhat.com> Reviewed-by:
Andreas Dilger <adilger@dilger.ca> Signed-off-by:
-
Filipe Manana authored
commit 1d512cb7 upstream. If we are using the NO_HOLES feature, we have a tiny time window when running delalloc for a nodatacow inode where we can race with a concurrent link or xattr add operation leading to a BUG_ON. This happens because at run_delalloc_nocow() we end up casting a leaf item of type BTRFS_INODE_[REF|EXTREF]_KEY or of type BTRFS_XATTR_ITEM_KEY to a file extent item (struct btrfs_file_extent_item) and then analyse its extent type field, which won't match any of the expected extent types (values BTRFS_FILE_EXTENT_[REG|PREALLOC|INLINE]) and therefore trigger an explicit BUG_ON(1). The following sequence diagram shows how the race happens when running a no-cow dellaloc range [4K, 8K[ for inode 257 and we have the following neighbour leafs: Leaf X (has N items) Leaf Y [ ... (257 INODE_ITEM 0) (257 INODE_REF 256) ] [ (257 EXTENT_DATA 8192), ... ] slot N - 2 slot N - 1 slot 0 (Note the implicit hole for inode 257 regarding the [0, 8K[ range) CPU 1 CPU 2 run_dealloc_nocow() btrfs_lookup_file_extent() --> searches for a key with value (257 EXTENT_DATA 4096) in the fs/subvol tree --> returns us a path with path->nodes[0] == leaf X and path->slots[0] == N because path->slots[0] is >= btrfs_header_nritems(leaf X), it calls btrfs_next_leaf() btrfs_next_leaf() --> releases the path hard link added to our inode, with key (257 INODE_REF 500) added to the end of leaf X, so leaf X now has N + 1 keys --> searches for the key (257 INODE_REF 256), because it was the last key in leaf X before it released the path, with path->keep_locks set to 1 --> ends up at leaf X again and it verifies that the key (257 INODE_REF 256) is no longer the last key in the leaf, so it returns with path->nodes[0] == leaf X and path->slots[0] == N, pointing to the new item with key (257 INODE_REF 500) the loop iteration of run_dealloc_nocow() does not break out the loop and continues because the key referenced in the path at path->nodes[0] and path->slots[0] is for inode 257, its type is < BTRFS_EXTENT_DATA_KEY and its offset (500) is less then our delalloc range's end (8192) the item pointed by the path, an inode reference item, is (incorrectly) interpreted as a file extent item and we get an invalid extent type, leading to the BUG_ON(1): if (extent_type == BTRFS_FILE_EXTENT_REG || extent_type == BTRFS_FILE_EXTENT_PREALLOC) { (...) } else if (extent_type == BTRFS_FILE_EXTENT_INLINE) { (...) } else { BUG_ON(1) } The same can happen if a xattr is added concurrently and ends up having a key with an offset smaller then the delalloc's range end. So fix this by skipping keys with a type smaller than BTRFS_EXTENT_DATA_KEY. Signed-off-by:
Filipe Manana <fdmanana@suse.com> Signed-off-by:
-
Filipe Manana authored
commit aeafbf84 upstream. While running a stress test I got the following warning triggered: [191627.672810] ------------[ cut here ]------------ [191627.673949] WARNING: CPU: 8 PID: 8447 at fs/btrfs/file.c:779 __btrfs_drop_extents+0x391/0xa50 [btrfs]() (...) [191627.701485] Call Trace: [191627.702037] [<ffffffff8145f077>] dump_stack+0x4f/0x7b [191627.702992] [<ffffffff81095de5>] ? console_unlock+0x356/0x3a2 [191627.704091] [<ffffffff8104b3b0>] warn_slowpath_common+0xa1/0xbb [191627.705380] [<ffffffffa0664499>] ? __btrfs_drop_extents+0x391/0xa50 [btrfs] [191627.706637] [<ffffffff8104b46d>] warn_slowpath_null+0x1a/0x1c [191627.707789] [<ffffffffa0664499>] __btrfs_drop_extents+0x391/0xa50 [btrfs] [191627.709155] [<ffffffff8115663c>] ? cache_alloc_debugcheck_after.isra.32+0x171/0x1d0 [191627.712444] [<ffffffff81155007>] ? kmemleak_alloc_recursive.constprop.40+0x16/0x18 [191627.714162] [<ffffffffa06570c9>] insert_reserved_file_extent.constprop.40+0x83/0x24e [btrfs] [191627.715887] [<ffffffffa065422b>] ? start_transaction+0x3bb/0x610 [btrfs] [191627.717287] [<ffffffffa065b604>] btrfs_finish_ordered_io+0x273/0x4e2 [btrfs] [191627.728865] [<ffffffffa065b888>] finish_ordered_fn+0x15/0x17 [btrfs] [191627.730045] [<ffffffffa067d688>] normal_work_helper+0x14c/0x32c [btrfs] [191627.731256] [<ffffffffa067d96a>] btrfs_endio_write_helper+0x12/0x14 [btrfs] [191627.732661] [<ffffffff81061119>] process_one_work+0x24c/0x4ae [191627.733822] [<ffffffff810615b0>] worker_thread+0x206/0x2c2 [191627.734857] [<ffffffff810613aa>] ? process_scheduled_works+0x2f/0x2f [191627.736052] [<ffffffff810613aa>] ? process_scheduled_works+0x2f/0x2f [191627.737349] [<ffffffff810669a6>] kthread+0xef/0xf7 [191627.738267] [<ffffffff810f3b3a>] ? time_hardirqs_on+0x15/0x28 [191627.739330] [<ffffffff810668b7>] ? __kthread_parkme+0xad/0xad [191627.741976] [<ffffffff81465592>] ret_from_fork+0x42/0x70 [191627.743080] [<ffffffff810668b7>] ? __kthread_parkme+0xad/0xad [191627.744206] ---[ end trace bbfddacb7aaada8d ]--- $ cat -n fs/btrfs/file.c 691 int __btrfs_drop_extents(struct btrfs_trans_handle *trans, (...) 758 btrfs_item_key_to_cpu(leaf, &key, path->slots[0]); 759 if (key.objectid > ino || 760 key.type > BTRFS_EXTENT_DATA_KEY || key.offset >= end) 761 break; 762 763 fi = btrfs_item_ptr(leaf, path->slots[0], 764 struct btrfs_file_extent_item); 765 extent_type = btrfs_file_extent_type(leaf, fi); 766 767 if (extent_type == BTRFS_FILE_EXTENT_REG || 768 extent_type == BTRFS_FILE_EXTENT_PREALLOC) { (...) 774 } else if (extent_type == BTRFS_FILE_EXTENT_INLINE) { (...) 778 } else { 779 WARN_ON(1); 780 extent_end = search_start; 781 } (...) This happened because the item we were processing did not match a file extent item (its key type != BTRFS_EXTENT_DATA_KEY), and even on this case we cast the item to a struct btrfs_file_extent_item pointer and then find a type field value that does not match any of the expected values (BTRFS_FILE_EXTENT_[REG|PREALLOC|INLINE]). This scenario happens due to a tiny time window where a race can happen as exemplified below. For example, consider the following scenario where we're using the NO_HOLES feature and we have the following two neighbour leafs: Leaf X (has N items) Leaf Y [ ... (257 INODE_ITEM 0) (257 INODE_REF 256) ] [ (257 EXTENT_DATA 8192), ... ] slot N - 2 slot N - 1 slot 0 Our inode 257 has an implicit hole in the range [0, 8K[ (implicit rather than explicit because NO_HOLES is enabled). Now if our inode has an ordered extent for the range [4K, 8K[ that is finishing, the following can happen: CPU 1 CPU 2 btrfs_finish_ordered_io() insert_reserved_file_extent() __btrfs_drop_extents() Searches for the key (257 EXTENT_DATA 4096) through btrfs_lookup_file_extent() Key not found and we get a path where path->nodes[0] == leaf X and path->slots[0] == N Because path->slots[0] is >= btrfs_header_nritems(leaf X), we call btrfs_next_leaf() btrfs_next_leaf() releases the path inserts key (257 INODE_REF 4096) at the end of leaf X, leaf X now has N + 1 keys, and the new key is at slot N btrfs_next_leaf() searches for key (257 INODE_REF 256), with path->keep_locks set to 1, because it was the last key it saw in leaf X finds it in leaf X again and notices it's no longer the last key of the leaf, so it returns 0 with path->nodes[0] == leaf X and path->slots[0] == N (which is now < btrfs_header_nritems(leaf X)), pointing to the new key (257 INODE_REF 4096) __btrfs_drop_extents() casts the item at path->nodes[0], slot path->slots[0], to a struct btrfs_file_extent_item - it does not skip keys for the target inode with a type less than BTRFS_EXTENT_DATA_KEY (BTRFS_INODE_REF_KEY < BTRFS_EXTENT_DATA_KEY) sees a bogus value for the type field triggering the WARN_ON in the trace shown above, and sets extent_end = search_start (4096) does the if-then-else logic to fixup 0 length extent items created by a past bug from hole punching: if (extent_end == key.offset && extent_end >= search_start) goto delete_extent_item; that evaluates to true and it ends up deleting the key pointed to by path->slots[0], (257 INODE_REF 4096), from leaf X The same could happen for example for a xattr that ends up having a key with an offset value that matches search_start (very unlikely but not impossible). So fix this by ensuring that keys smaller than BTRFS_EXTENT_DATA_KEY are skipped, never casted to struct btrfs_file_extent_item and never deleted by accident. Also protect against the unexpected case of getting a key for a lower inode number by skipping that key and issuing a warning. Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 602dd62d ] Dmitry Vyukov reported a memory leak using IPV6 SCTP sockets. We need to call inet6_destroy_sock() to properly release inet6 specific fields. Reported-by:
Dmitry Vyukov <dvyukov@google.com> Signed-off-by:
Eric Dumazet <edumazet@google.com> Acked-by:
Daniel Borkmann <daniel@iogearbox.net> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Michal Kubeček authored
[ Upstream commit 264640fc ] If a fragmented multicast packet is received on an ethernet device which has an active macvlan on top of it, each fragment is duplicated and received both on the underlying device and the macvlan. If some fragments for macvlan are processed before the whole packet for the underlying device is reassembled, the "overlapping fragments" test in ip6_frag_queue() discards the whole fragment queue. To resolve this, add device ifindex to the search key and require it to match reassembling multicast packets and packets to link-local addresses. Note: similar patch has been already submitted by Yoshifuji Hideaki in http://patchwork.ozlabs.org/patch/220979/ but got lost and forgotten for some reason. Signed-off-by:
Michal Kubecek <mkubecek@suse.cz> Signed-off-by:
-
Aaro Koskinen authored
[ Upstream commit 3c25a860 ] Commit fcb26ec5 ("broadcom: move all PHY_ID's to header") updated broadcom_tbl to use PHY_IDs, but incorrectly replaced 0x0143bca0 with PHY_ID_BCM5482 (making a duplicate entry, and completely omitting the original). Fix that. Fixes: fcb26ec5 ("broadcom: move all PHY_ID's to header") Signed-off-by:
Aaro Koskinen <aaro.koskinen@iki.fi> Signed-off-by:
-
Nikolay Aleksandrov authored
[ Upstream commit 4c698046 ] Similar to ipv4, when destroying an mrt table the static mfc entries and the static devices are kept, which leads to devices that can never be destroyed (because of refcnt taken) and leaked memory. Make sure that everything is cleaned up on netns destruction. Fixes: 8229efda ("netns: ip6mr: enable namespace support in ipv6 multicast forwarding code") CC: Benjamin Thery <benjamin.thery@bull.net> Signed-off-by:
Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Reviewed-by:
Cong Wang <cwang@twopensource.com> Signed-off-by:
-
Nikolay Aleksandrov authored
[ Upstream commit 0e615e96 ] When destroying an mrt table the static mfc entries and the static devices are kept, which leads to devices that can never be destroyed (because of refcnt taken) and leaked memory, for example: unreferenced object 0xffff880034c144c0 (size 192): comm "mfc-broken", pid 4777, jiffies 4320349055 (age 46001.964s) hex dump (first 32 bytes): 98 53 f0 34 00 88 ff ff 98 53 f0 34 00 88 ff ff .S.4.....S.4.... ef 0a 0a 14 01 02 03 04 00 00 00 00 01 00 00 00 ................ backtrace: [<ffffffff815c1b9e>] kmemleak_alloc+0x4e/0xb0 [<ffffffff811ea6e0>] kmem_cache_alloc+0x190/0x300 [<ffffffff815931cb>] ip_mroute_setsockopt+0x5cb/0x910 [<ffffffff8153d575>] do_ip_setsockopt.isra.11+0x105/0xff0 [<ffffffff8153e490>] ip_setsockopt+0x30/0xa0 [<ffffffff81564e13>] raw_setsockopt+0x33/0x90 [<ffffffff814d1e14>] sock_common_setsockopt+0x14/0x20 [<ffffffff814d0b51>] SyS_setsockopt+0x71/0xc0 [<ffffffff815cdbf6>] entry_SYSCALL_64_fastpath+0x16/0x7a [<ffffffffffffffff>] 0xffffffffffffffff Make sure that everything is cleaned on netns destruction. Signed-off-by:
-
Daniel Borkmann authored
[ Upstream commit 6900317f ] David and HacKurx reported a following/similar size overflow triggered in a grsecurity kernel, thanks to PaX's gcc size overflow plugin: (Already fixed in later grsecurity versions by Brad and PaX Team.) [ 1002.296137] PAX: size overflow detected in function scm_detach_fds net/core/scm.c:314 cicus.202_127 min, count: 4, decl: msg_controllen; num: 0; context: msghdr; [ 1002.296145] CPU: 0 PID: 3685 Comm: scm_rights_recv Not tainted 4.2.3-grsec+ #7 [ 1002.296149] Hardware name: Apple Inc. MacBookAir5,1/Mac-66F35F19FE2A0D05, [...] [ 1002.296153] ffffffff81c27366 0000000000000000 ffffffff81c27375 ffffc90007843aa8 [ 1002.296162] ffffffff818129ba 0000000000000000 ffffffff81c27366 ffffc90007843ad8 [ 1002.296169] ffffffff8121f838 fffffffffffffffc fffffffffffffffc ffffc90007843e60 [ 1002.296176] Call Trace: [ 1002.296190] [<ffffffff818129ba>] dump_stack+0x45/0x57 [ 1002.296200] [<ffffffff8121f838>] report_size_overflow+0x38/0x60 [ 1002.296209] [<ffffffff816a979e>] scm_detach_fds+0x2ce/0x300 [ 1002.296220] [<ffffffff81791899>] unix_stream_read_generic+0x609/0x930 [ 1002.296228] [<ffffffff81791c9f>] unix_stream_recvmsg+0x4f/0x60 [ 1002.296236] [<ffffffff8178dc00>] ? unix_set_peek_off+0x50/0x50 [ 1002.296243] [<ffffffff8168fac7>] sock_recvmsg+0x47/0x60 [ 1002.296248] [<ffffffff81691522>] ___sys_recvmsg+0xe2/0x1e0 [ 1002.296257] [<ffffffff81693496>] __sys_recvmsg+0x46/0x80 [ 1002.296263] [<ffffffff816934fc>] SyS_recvmsg+0x2c/0x40 [ 1002.296271] [<ffffffff8181a3ab>] entry_SYSCALL_64_fastpath+0x12/0x85 Further investigation showed that this can happen when an *odd* number of fds are being passed over AF_UNIX sockets. In these cases CMSG_LEN(i * sizeof(int)) and CMSG_SPACE(i * sizeof(int)), where i is the number of successfully passed fds, differ by 4 bytes due to the extra CMSG_ALIGN() padding in CMSG_SPACE() to an 8 byte boundary on 64 bit. The padding is used to align subsequent cmsg headers in the control buffer. When the control buffer passed in from the receiver side *lacks* these 4 bytes (e.g. due to buggy/wrong API usage), then msg->msg_controllen will overflow in scm_detach_fds(): int cmlen = CMSG_LEN(i * sizeof(int)); <--- cmlen w/o tail-padding err = put_user(SOL_SOCKET, &cm->cmsg_level); if (!err) err = put_user(SCM_RIGHTS, &cm->cmsg_type); if (!err) err = put_user(cmlen, &cm->cmsg_len); if (!err) { cmlen = CMSG_SPACE(i * sizeof(int)); <--- cmlen w/ 4 byte extra tail-padding msg->msg_control += cmlen; msg->msg_controllen -= cmlen; <--- iff no tail-padding space here ... } ... wrap-around F.e. it will wrap to a length of 18446744073709551612 bytes in case the receiver passed in msg->msg_controllen of 20 bytes, and the sender properly transferred 1 fd to the receiver, so that its CMSG_LEN results in 20 bytes and CMSG_SPACE in 24 bytes. In case of MSG_CMSG_COMPAT (scm_detach_fds_compat()), I haven't seen an issue in my tests as alignment seems always on 4 byte boundary. Same should be in case of native 32 bit, where we end up with 4 byte boundaries as well. In practice, passing msg->msg_controllen of 20 to recvmsg() while receiving a single fd would mean that on successful return, msg->msg_controllen is being set by the kernel to 24 bytes instead, thus more than the input buffer advertised. It could f.e. become an issue if such application later on zeroes or copies the control buffer based on the returned msg->msg_controllen elsewhere. Maximum number of fds we can send is a hard upper limit SCM_MAX_FD (253). Going over the code, it seems like msg->msg_controllen is not being read after scm_detach_fds() in scm_recv() anymore by the kernel, good! Relevant recvmsg() handler are unix_dgram_recvmsg() (unix_seqpacket_recvmsg()) and unix_stream_recvmsg(). Both return back to their recvmsg() caller, and ___sys_recvmsg() places the updated length, that is, new msg_control - old msg_control pointer into msg->msg_controllen (hence the 24 bytes seen in the example). Long time ago, Wei Yongjun fixed something related in commit 1ac70e7a ("[NET]: Fix function put_cmsg() which may cause usr application memory overflow"). RFC3542, section 20.2. says: The fields shown as "XX" are possible padding, between the cmsghdr structure and the data, and between the data and the next cmsghdr structure, if required by the implementation. While sending an application may or may not include padding at the end of last ancillary data in msg_controllen and implementations must accept both as valid. On receiving a portable application must provide space for padding at the end of the last ancillary data as implementations may copy out the padding at the end of the control message buffer and include it in the received msg_controllen. When recvmsg() is called if msg_controllen is too small for all the ancillary data items including any trailing padding after the last item an implementation may set MSG_CTRUNC. Since we didn't place MSG_CTRUNC for already quite a long time, just do the same as in 1ac70e7a to avoid an overflow. Btw, even man-page author got this wrong :/ See db939c9b26e9 ("cmsg.3: Fix error in SCM_RIGHTS code sample"). Some people must have copied this (?), thus it got triggered in the wild (reported several times during boot by David and HacKurx). No Fixes tag this time as pre 2002 (that is, pre history tree). Reported-by:
David Sterba <dave@jikos.cz> Reported-by:
HacKurx <hackurx@gmail.com> Cc: PaX Team <pageexec@freemail.hu> Cc: Emese Revfy <re.emese@gmail.com> Cc: Brad Spengler <spender@grsecurity.net> Cc: Wei Yongjun <yongjun_wei@trendmicro.com.cn> Cc: Eric Dumazet <edumazet@google.com> Reviewed-by:
Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 142a2e7e ] Dmitry provided a syzkaller (http://github.com/google/syzkaller) generated program that triggers the WARNING at net/ipv4/tcp.c:1729 in tcp_recvmsg() : WARN_ON(tp->copied_seq != tp->rcv_nxt && !(flags & (MSG_PEEK | MSG_TRUNC))); His program is specifically attempting a Cross SYN TCP exchange, that we support (for the pleasure of hackers ?), but it looks we lack proper tcp->copied_seq initialization. Thanks again Dmitry for your report and testings. Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 1b8e6a01 ] When a passive TCP is created, we eventually call tcp_md5_do_add() with sk pointing to the child. It is not owner by the user yet (we will add this socket into listener accept queue a bit later anyway) But we do own the spinlock, so amend the lockdep annotation to avoid following splat : [ 8451.090932] net/ipv4/tcp_ipv4.c:923 suspicious rcu_dereference_protected() usage! [ 8451.090932] [ 8451.090932] other info that might help us debug this: [ 8451.090932] [ 8451.090934] [ 8451.090934] rcu_scheduler_active = 1, debug_locks = 1 [ 8451.090936] 3 locks held by socket_sockopt_/214795: [ 8451.090936] #0: (rcu_read_lock){.+.+..}, at: [<ffffffff855c6ac1>] __netif_receive_skb_core+0x151/0xe90 [ 8451.090947] #1: (rcu_read_lock){.+.+..}, at: [<ffffffff85618143>] ip_local_deliver_finish+0x43/0x2b0 [ 8451.090952] #2: (slock-AF_INET){+.-...}, at: [<ffffffff855acda5>] sk_clone_lock+0x1c5/0x500 [ 8451.090958] [ 8451.090958] stack backtrace: [ 8451.090960] CPU: 7 PID: 214795 Comm: socket_sockopt_ [ 8451.091215] Call Trace: [ 8451.091216] <IRQ> [<ffffffff856fb29c>] dump_stack+0x55/0x76 [ 8451.091229] [<ffffffff85123b5b>] lockdep_rcu_suspicious+0xeb/0x110 [ 8451.091235] [<ffffffff8564544f>] tcp_md5_do_add+0x1bf/0x1e0 [ 8451.091239] [<ffffffff85645751>] tcp_v4_syn_recv_sock+0x1f1/0x4c0 [ 8451.091242] [<ffffffff85642b27>] ? tcp_v4_md5_hash_skb+0x167/0x190 [ 8451.091246] [<ffffffff85647c78>] tcp_check_req+0x3c8/0x500 [ 8451.091249] [<ffffffff856451ae>] ? tcp_v4_inbound_md5_hash+0x11e/0x190 [ 8451.091253] [<ffffffff85647170>] tcp_v4_rcv+0x3c0/0x9f0 [ 8451.091256] [<ffffffff85618143>] ? ip_local_deliver_finish+0x43/0x2b0 [ 8451.091260] [<ffffffff856181b6>] ip_local_deliver_finish+0xb6/0x2b0 [ 8451.091263] [<ffffffff85618143>] ? ip_local_deliver_finish+0x43/0x2b0 [ 8451.091267] [<ffffffff85618d38>] ip_local_deliver+0x48/0x80 [ 8451.091270] [<ffffffff85618510>] ip_rcv_finish+0x160/0x700 [ 8451.091273] [<ffffffff8561900e>] ip_rcv+0x29e/0x3d0 [ 8451.091277] [<ffffffff855c74b7>] __netif_receive_skb_core+0xb47/0xe90 Fixes: a8afca03 ("tcp: md5: protects md5sig_info with RCU") Signed-off-by:
Willem de Bruijn <willemb@google.com> Signed-off-by:
-
Bjørn Mork authored
[ Upstream commit 68242a5a ] Thomas reports " 4gsystems sells two total different LTE-surfsticks under the same name. .. The newer version of XS Stick W100 is from "omega" .. Under windows the driver switches to the same ID, and uses MI03\6 for network and MI01\6 for modem. .. echo "1c9e 9b01" > /sys/bus/usb/drivers/qmi_wwan/new_id echo "1c9e 9b01" > /sys/bus/usb-serial/drivers/option1/new_id T: Bus=01 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#= 4 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1c9e ProdID=9b01 Rev=02.32 S: Manufacturer=USB Modem S: Product=USB Modem S: SerialNumber= C: #Ifs= 5 Cfg#= 1 Atr=80 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan I: If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage Now all important things are there: wwp0s29f7u2i3 (net), ttyUSB2 (at), cdc-wdm0 (qmi), ttyUSB1 (at) There is also ttyUSB0, but it is not usable, at least not for at. The device works well with qmi and ModemManager-NetworkManager. " Reported-by:
Thomas Schäfer <tschaefer@t-online.de> Signed-off-by:
Bjørn Mork <bjorn@mork.no> Signed-off-by:
-
Neil Horman authored
[ Upstream commit 41033f02 ] the OUTMCAST stat is double incremented, getting bumped once in the mcast code itself, and again in the common ip output path. Remove the mcast bump, as its not needed Validated by the reporter, with good results Signed-off-by:
Neil Horman <nhorman@tuxdriver.com> Reported-by:
Claus Jensen <claus.jensen@microsemi.com> CC: Claus Jensen <claus.jensen@microsemi.com> CC: David Miller <davem@davemloft.net> Signed-off-by:
-
Jason A. Donenfeld authored
[ Upstream commit b4fe85f9 ] Drivers like vxlan use the recently introduced udp_tunnel_xmit_skb/udp_tunnel6_xmit_skb APIs. udp_tunnel6_xmit_skb makes use of ip6tunnel_xmit, and ip6tunnel_xmit, after sending the packet, updates the struct stats using the usual u64_stats_update_begin/end calls on this_cpu_ptr(dev->tstats). udp_tunnel_xmit_skb makes use of iptunnel_xmit, which doesn't touch tstats, so drivers like vxlan, immediately after, call iptunnel_xmit_stats, which does the same thing - calls u64_stats_update_begin/end on this_cpu_ptr(dev->tstats). While vxlan is probably fine (I don't know?), calling a similar function from, say, an unbound workqueue, on a fully preemptable kernel causes real issues: [ 188.434537] BUG: using smp_processor_id() in preemptible [00000000] code: kworker/u8:0/6 [ 188.435579] caller is debug_smp_processor_id+0x17/0x20 [ 188.435583] CPU: 0 PID: 6 Comm: kworker/u8:0 Not tainted 4.2.6 #2 [ 188.435607] Call Trace: [ 188.435611] [<ffffffff8234e936>] dump_stack+0x4f/0x7b [ 188.435615] [<ffffffff81915f3d>] check_preemption_disabled+0x19d/0x1c0 [ 188.435619] [<ffffffff81915f77>] debug_smp_processor_id+0x17/0x20 The solution would be to protect the whole this_cpu_ptr(dev->tstats)/u64_stats_update_begin/end blocks with disabling preemption and then reenabling it. Signed-off-by:
Jason A. Donenfeld <Jason@zx2c4.com> Acked-by:
-
lucien authored
[ Upstream commit ed5a377d ] now sctp auth cannot work well when setting a hmacid manually, which is caused by that we didn't use the network order for hmacid, so fix it by adding the transformation in sctp_auth_ep_set_hmacs. even we set hmacid with the network order in userspace, it still can't work, because of this condition in sctp_auth_ep_set_hmacs(): if (id > SCTP_AUTH_HMAC_ID_MAX) return -EOPNOTSUPP; so this wasn't working before and thus it won't break compatibility. Fixes: 65b07e5d ("[SCTP]: API updates to suport SCTP-AUTH extensions.") Signed-off-by:
Xin Long <lucien.xin@gmail.com> Signed-off-by:
Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Acked-by:
Vlad Yasevich <vyasevich@gmail.com> Signed-off-by:
-
Daniel Borkmann authored
[ Upstream commit c72219b7 ] In case no struct sockaddr_ll has been passed to packet socket's sendmsg() when doing a TX_RING flush run, then skb->protocol is set to po->num instead, which is the protocol passed via socket(2)/bind(2). Applications only xmitting can go the path of allocating the socket as socket(PF_PACKET, <mode>, 0) and do a bind(2) on the TX_RING with sll_protocol of 0. That way, register_prot_hook() is neither called on creation nor on bind time, which saves cycles when there's no interest in capturing anyway. That leaves us however with po->num 0 instead and therefore the TX_RING flush run sets skb->protocol to 0 as well. Eric reported that this leads to problems when using tools like trafgen over bonding device. I.e. the bonding's hash function could invoke the kernel's flow dissector, which depends on skb->protocol being properly set. In the current situation, all the traffic is then directed to a single slave. Fix it up by inferring skb->protocol from the Ethernet header when not set and we have ARPHRD_ETHER device type. This is only done in case of SOCK_RAW and where we have a dev->hard_header_len length. In case of ARPHRD_ETHER devices, this is guaranteed to cover ETH_HLEN, and therefore being accessed on the skb after the skb_store_bits(). Reported-by:
-
Daniel Borkmann authored
[ Upstream commit 8fd6c80d ] We concluded that the skb_probe_transport_header() should better be called unconditionally. Avoiding the call into the flow dissector has also not really much to do with the direct xmit mode. While it seems that only virtio_net code makes use of GSO from non RX/TX ring packet socket paths, we should probe for a transport header nevertheless before they hit devices. Reference: http://thread.gmane.org/gmane.linux.network/386173/Signed-off-by:
Jason Wang <jasowang@redhat.com> Signed-off-by:
-
Daniel Borkmann authored
[ Upstream commit efdfa2f7 ] In tpacket_fill_skb() commit c1aad275 ("packet: set transport header before doing xmit") and later on 40893fd0 ("net: switch to use skb_probe_transport_header()") was probing for a transport header on the skb from a ring buffer slot, but at a time, where the skb has _not even_ been filled with data yet. So that call into the flow dissector is pretty useless. Lets do it after we've set up the skb frags. Fixes: c1aad275 ("packet: set transport header before doing xmit") Reported-by:
-
Kamal Mostafa authored
[ Upstream commit d7475de5 ] Use the local uapi headers to keep in sync with "recently" added #define's (e.g. SKF_AD_VLAN_TPID). Refactored CFLAGS, and bpf_asm doesn't need -I. Fixes: 3f356385 ("filter: bpf_asm: add minimal bpf asm tool") Signed-off-by:
Kamal Mostafa <kamal@canonical.com> Acked-by:
-
Rainer Weikusat authored
[ Upstream commit 7d267278 ] Rainer Weikusat <rweikusat@mobileactivedefense.com> writes: An AF_UNIX datagram socket being the client in an n:1 association with some server socket is only allowed to send messages to the server if the receive queue of this socket contains at most sk_max_ack_backlog datagrams. This implies that prospective writers might be forced to go to sleep despite none of the message presently enqueued on the server receive queue were sent by them. In order to ensure that these will be woken up once space becomes again available, the present unix_dgram_poll routine does a second sock_poll_wait call with the peer_wait wait queue of the server socket as queue argument (unix_dgram_recvmsg does a wake up on this queue after a datagram was received). This is inherently problematic because the server socket is only guaranteed to remain alive for as long as the client still holds a reference to it. In case the connection is dissolved via connect or by the dead peer detection logic in unix_dgram_sendmsg, the server socket may be freed despite "the polling mechanism" (in particular, epoll) still has a pointer to the corresponding peer_wait queue. There's no way to forcibly deregister a wait queue with epoll. Based on an idea by Jason Baron, the patch below changes the code such that a wait_queue_t belonging to the client socket is enqueued on the peer_wait queue of the server whenever the peer receive queue full condition is detected by either a sendmsg or a poll. A wake up on the peer queue is then relayed to the ordinary wait queue of the client socket via wake function. The connection to the peer wait queue is again dissolved if either a wake up is about to be relayed or the client socket reconnects or a dead peer is detected or the client socket is itself closed. This enables removing the second sock_poll_wait from unix_dgram_poll, thus avoiding the use-after-free, while still ensuring that no blocked writer sleeps forever. Signed-off-by:
Rainer Weikusat <rweikusat@mobileactivedefense.com> Fixes: ec0d215f ("af_unix: fix 'poll for write'/connected DGRAM sockets") Reviewed-by:
Jason Baron <jbaron@akamai.com> Signed-off-by:
-
- 09 Dec, 2015 9 commits
-
-
Greg Kroah-Hartman authored
-
Clemens Ladisch authored
commit a91e627e upstream. One of the many faults of the QinHeng CH345 USB MIDI interface chip is that it does not handle received SysEx messages correctly -- every second event packet has a wrong code index number, which is the one from the last seen message, instead of 4. For example, the two messages "FE F0 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E F7" result in the following event packets: correct: CH345: 0F FE 00 00 0F FE 00 00 04 F0 01 02 04 F0 01 02 04 03 04 05 0F 03 04 05 04 06 07 08 04 06 07 08 04 09 0A 0B 0F 09 0A 0B 04 0C 0D 0E 04 0C 0D 0E 05 F7 00 00 05 F7 00 00 A class-compliant driver must interpret an event packet with CIN 15 as having a single data byte, so the other two bytes would be ignored. The message received by the host would then be missing two bytes out of six; in this example, "F0 01 02 03 06 07 08 09 0C 0D 0E F7". These corrupted SysEx event packages contain only data bytes, while the CH345 uses event packets with a correct CIN value only for messages with a status byte, so it is possible to distinguish between these two cases by checking for the presence of this status byte. (Other bugs in the CH345's input handling, such as the corruption resulting from running status, cannot be worked around.) Signed-off-by:
Clemens Ladisch <clemens@ladisch.de> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Clemens Ladisch authored
commit 1ca8b201 upstream. The CH345 USB MIDI chip has two output ports. However, they are multiplexed through one pin, and the number of ports cannot be reduced even for hardware that implements only one connector, so for those devices, data sent to either port ends up on the same hardware output. This becomes a problem when both ports are used at the same time, as longer MIDI commands (such as SysEx messages) are likely to be interrupted by messages from the other port, and thus to get lost. It would not be possible for the driver to detect how many ports the device actually has, except that in practice, _all_ devices built with the CH345 have only one port. So we can just ignore the device's descriptors, and hardcode one output port. Signed-off-by:
-
Clemens Ladisch authored
commit 98d362be upstream. Signed-off-by:
-
Bjørn Mork authored
commit 638148e2 upstream. Thomas reports " 4gsystems sells two total different LTE-surfsticks under the same name. .. The newer version of XS Stick W100 is from "omega" .. Under windows the driver switches to the same ID, and uses MI03\6 for network and MI01\6 for modem. .. echo "1c9e 9b01" > /sys/bus/usb/drivers/qmi_wwan/new_id echo "1c9e 9b01" > /sys/bus/usb-serial/drivers/option1/new_id T: Bus=01 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#= 4 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1c9e ProdID=9b01 Rev=02.32 S: Manufacturer=USB Modem S: Product=USB Modem S: SerialNumber= C: #Ifs= 5 Cfg#= 1 Atr=80 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan I: If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage Now all important things are there: wwp0s29f7u2i3 (net), ttyUSB2 (at), cdc-wdm0 (qmi), ttyUSB1 (at) There is also ttyUSB0, but it is not usable, at least not for at. The device works well with qmi and ModemManager-NetworkManager. " Reported-by:
-
Aleksander Morgado authored
commit e07af133 upstream. Also known as Verizon U620L. The device is modeswitched from 1410:9020 to 1410:9022 by selecting the 4th USB configuration: $ sudo usb_modeswitch –v 0x1410 –p 0x9020 –u 4 This configuration provides a ECM interface as well as TTYs ('Enterprise Mode' according to the U620 Linux integration guide). Signed-off-by:
Aleksander Morgado <aleksander@aleksander.es> Signed-off-by:
-
David Woodhouse authored
commit 1bcb49e6 upstream. The Honeywell HGI80 is a wireless interface to the evohome connected thermostat. It uses a TI 3410 USB-serial port. Signed-off-by:
David Woodhouse <David.Woodhouse@intel.com> Signed-off-by:
-
Uwe Kleine-König authored
commit 705e63d2 upstream. There is a bit of a mess in the order of arguments to the ulpi write callback. There is int ulpi_write(struct ulpi *ulpi, u8 addr, u8 val) in drivers/usb/common/ulpi.c; struct usb_phy_io_ops { ... int (*write)(struct usb_phy *x, u32 val, u32 reg); } in include/linux/usb/phy.h. The callback registered by the musb driver has to comply to the latter, but up to now had "offset" first which effectively made the function broken for correct users. So flip the order and while at it also switch to the parameter names of struct usb_phy_io_ops's write. Fixes: ffb865b1 ("usb: musb: add ulpi access operations") Signed-off-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by:
Felipe Balbi <balbi@ti.com> Signed-off-by:
-
Jiri Slaby authored
commit 19cd80a2 upstream. It is not permitted to set task state before lock. usblp_wwait sets the state to TASK_INTERRUPTIBLE and calls mutex_lock_interruptible. Upon return from that function, the state will be TASK_RUNNING again. This is clearly a bug and a warning is generated with LOCKDEP too: WARNING: CPU: 1 PID: 5109 at kernel/sched/core.c:7404 __might_sleep+0x7d/0x90() do not call blocking ops when !TASK_RUNNING; state=1 set at [<ffffffffa0c588d0>] usblp_wwait+0xa0/0x310 [usblp] Modules linked in: ... CPU: 1 PID: 5109 Comm: captmon Tainted: G W 4.2.5-0.gef2823b-default #1 Hardware name: LENOVO 23252SG/23252SG, BIOS G2ET33WW (1.13 ) 07/24/2012 ffffffff81a4edce ffff880236ec7ba8 ffffffff81716651 0000000000000000 ffff880236ec7bf8 ffff880236ec7be8 ffffffff8106e146 0000000000000282 ffffffff81a50119 000000000000028b 0000000000000000 ffff8802dab7c508 Call Trace: ... [<ffffffff8106e1c6>] warn_slowpath_fmt+0x46/0x50 [<ffffffff8109a8bd>] __might_sleep+0x7d/0x90 [<ffffffff8171b20f>] mutex_lock_interruptible_nested+0x2f/0x4b0 [<ffffffffa0c588fc>] usblp_wwait+0xcc/0x310 [usblp] [<ffffffffa0c58bb2>] usblp_write+0x72/0x350 [usblp] [<ffffffff8121ed98>] __vfs_write+0x28/0xf0 ... Commit 7f477358 (usblp: Implement the ENOSPC convention) moved the set prior locking. So move it back after the lock. Signed-off-by:
Jiri Slaby <jslaby@suse.cz> Fixes: 7f477358 ("usblp: Implement the ENOSPC convention") Acked-By:
Pete Zaitcev <zaitcev@yahoo.com> Signed-off-by:
-
