- 11 Mar, 2016 40 commits
-
-
Mitko Haralanov authored
Change verbs memory allocations to the device numa node. This keeps memory close to the device for optimal performance. Reviewed-by:
Mike Marciniszyn <mike.marciniszyn@intel.com> Reviewed-by:
Ira Weiny <ira.weiny@intel.com> Signed-off-by:
Mitko Haralanov <mitko.haralanov@intel.com> Signed-off-by:
Doug Ledford <dledford@redhat.com>
-
Mitko Haralanov authored
Allocate the user mode send context memory on the numa node which the device is attached to for better performance. Reviewed-by:
Dean Luick <dean.luick@intel.com> Reviewed-by:
-
Mitko Haralanov authored
This patch unifies the affinity support for CPU and IRQ allocations into a single code base. The goal is to allow the driver to make intelligent placement decision based on an overall view of processes and IRQs across as much of the driver as possible. Pulling all the scattered affinity code into a single code base lays the ground work for accomplishing the above goal. For example, previous implementations made user process placement decision solely based on other user processes. This algorithm is limited as it did not take into account IRQ placement and could result in overloading certain CPUs. A single code base also provides a much easier way to maintain and debug any performance issues related to affinity. Reviewed-by:
-
Mitko Haralanov authored
struct hfi1_devdata contained 2 variables which represented the numa node the device is attached to. Remove the duplicated one. Reviewed-by:
-
Mitko Haralanov authored
This comment and code was unused. Just remove it. Reviewed-by:
-
Ira Weiny authored
SLs which are mapped to SC15 are invalid and should fail the operation. For RC/UC QP types, verify the AH information at modify_qp time and fail the modify_qp if the SL is invalid. For other QP types check the SL during post_send via the new rdmavt callback. Reviewed-by:
Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by:
-
Ashutosh Dixit authored
hfi1 HW has a high PCIe ASPM L1 exit latency and also advertises an acceptable latency less than actual ASPM latencies. Additional mechanisms than those provided by BIOS/OS are therefore required to enable/disable ASPM for hfi1 to provide acceptable power/performance trade offs. This patch adds this support. By means of a module parameter ASPM can be either (a) always enabled (power save mode) (b) always disabled (performance mode) (c) enabled/disabled dynamically. The dynamic mode implements two heuristics to alleviate possible problems with high ASPM L1 exit latency. ASPM is normally enabled but is disabled if (a) there are any active user space PSM contexts, or (b) for verbs, ASPM is disabled as interrupt activity for a context starts to increase. A few more points about the verbs implementation. In order to reduce lock/cache contention between multiple verbs contexts, some processing is done at the context layer before contending for device layer locks. ASPM is disabled when two interrupts for a context happen within 1 millisec. A timer is scheduled which will re-enable ASPM after 1 second should the interrupt activity cease. Normally, every interrupt, or interrupt-pair should push the timer out further. However, since this might increase the processing load per interrupt, pushing the timer out is postponed for half a second. If after half a second we get two interrupts within 1 millisec the timer is pushed out by another second. Finally, the kernel ASPM API is not used in this patch. This is because this patch does several non-standard things as SW workarounds for HW issues. As mentioned above, it enables ASPM even when advertised actual latencies are greater than acceptable latencies. Also, whereas the kernel API only allows drivers to disable ASPM from driver probe, this patch enables/disables ASPM directly from interrupt context. Due to these reasons the kernel ASPM API was not used. Reviewed-by:
Ashutosh Dixit <ashutosh.dixit@intel.com> Signed-off-by:
-
Vennila Megavannan authored
Add a per port sysfs paramter to toggle cc_prescan/Fast ECN Detection and remove the Kconfig option which was previously used to control this. While am updating the sysfs documentation, fix the name of CCMgtA. Reviewed-by:
Arthur Kepner <arthur.kepner@intel.com> Reviewed-by:
Vennila Megavannan <vennila.megavannan@intel.com> Signed-off-by:
-
Mitko Haralanov authored
The RcvCtxtCtrl register was being incorrectly set upon context initialization and clean up resulting, in many cases, of contexts using settings from previous contexts' initialization. This resulted in bad and unexpected behavior. This was especially important for the TailUpd bit, which requires special handling and if set incorrectly could lead to severely degraded performance. This patch fixes the handling of the RcvCtxtCtrl register, ensuring that each context gets initialized with settings applicable only for that context. It also ensures the proper setting for the TailUpd bit by setting it to either 0 or 1 (as needed by the context's configuration) explicitly. Reviewed-by:
-
Sebastian Sanchez authored
When 32-bit hardware counters overflow, hfi1stats misinterprets the counters as being 64 bits causing the deltas for the counters to be a huge number. This patch makes hfi1stats aware that a counter is 32 bits by making the driver write <counter name>,32 to debugfs. Reviewed-by:
Sebastian Sanchez <sebastian.sanchez@intel.com> Signed-off-by:
-
Dean Luick authored
The simulator does not correctly handle LCB cclk loopback. Skip that step for simulation - it is not needed. Reviewed-by:
-
Dean Luick authored
Simulation has no firmware, so it will never move firmware acquire to the FINAL state. Avoid that by skiping the TRY state and moving directly to FINAL. Reviewed-by:
-
Easwar Hariharan authored
Loopback plugs used for testing hardware don't need to be qualified to bring the link up unlike production cables. This patch adds an exception for loopback plugs to the QSFP and SerDes tuning algortihm. Reviewed-by:
Easwar Hariharan <easwar.hariharan@intel.com> Signed-off-by:
-
Dean Luick authored
Make firmware validation failure and missing firmware messages a warning since alternates can be tried. Add an error message when all attempts fail. Reviewed-by:
-
Dean Luick authored
Change-Id: Icc4ad27c4c67e51df8c8a203c4f16973793678ec Reviewed-by:
-
Mike Marciniszyn authored
Implement per-VL transmit counters. Not all errors can be attributed to a particular VL, so make a best attempt. o Extend the egress error bits used to count toward transmit discard. o When an egress error or send error occur, try to map back to a VL. o Implement a SDMA engine to VL (back) map. o Add per-VL port transmit counters Reviewed-by:
-
Dean Luick authored
The gen3 bump code must mark a firmware download failure as fatal. Otherwise a later load attempt will fail with a NULL dereference. Also: o Only do a firmware back-off for RTL. There are no alternates for FPGA or simulation. o Rearrange OS firmware request order to match what is actually loaded. This results in more coherent informational messages in the case of missing firmware. Reviewed-by:
-
Easwar Hariharan authored
This patch implements support for turning on and off the clock data recovery mechanisms implemented in QSFP cable on request by the DC 8051 on a per-lane basis. Reviewed-by:
-
Easwar Hariharan authored
The current code employs a heuristic to guess the port type. The canonical location to identify the port type of the designed platform is from the platform configuration data. This patch uses the previously fetched port type from the platform configuration and removes the now obsolete heuristic routine and its associated defines. Reviewed-by:
-
Easwar Hariharan authored
This patch qualifies and tunes active and optical cables for optimal bit error rate and signal integrity settings. These settings are fetched from the platform configuration data. Based on attributes of the QSFP cable as read from the SFF-8636 compliant memory map, we select the appropriate settings from the platform configuration data (examples: TX/RX equalization, enabling cable high power, enabling TX/RX clock data recovery mechanisms, and RX amplitude control) and apply them to the SERDES and QSFP cable. The platform configuration data also contains system parameters such as maximum power dissipation supported, and the cables are qualified based on these parameters. As part of qualifying the cables, the correct OfflineDisabledReasons are set for the appropriate scenarios. Reviewed-by:
Brent R Rothermel <brent.r.rothermel@intel.com> Signed-off-by:
Jubin John <jubin.john@intel.com> Signed-off-by:
-
Mike Marciniszyn authored
The QSFP memory cache reads both lower and upper page 0H in one shot, which leads to the address counter wrapping around to the beginning of lower page 00H at byte 128, as defined by SFF-8636. This patch fixes this by modifying the underlying QSFP read and writes to avoid this wrap around. Reviewed-by:
-
Easwar Hariharan authored
The ":" in "%s:" adds no value. Reviewed-by:
-
Bryan Morgan authored
Removing QSFP cable should report 'No Local Media' instead of 'Transient' as reported by 'opaportinfo'. Workaround is to change the state to OPA_LINKDOWN_REASON_LOCAL_MEDIA_NOT_INSTALLED in cable handler. With cable still removed, 'opaportinfo bounce' should not cause a state change to Polling, as reported by 'opaportinfo'. Resolution is to prevent physical state change from Offline->Polling. Use a macro to mask lower nibble of OPA_LINKDOWN_REASON* as needed for offline_disabled_reason. Reviewed-by:
Todd Rimmer <todd.rimmer@intel.com> Signed-off-by:
Bryan Morgan <bryan.c.morgan@intel.com> Signed-off-by:
-
Jubin John authored
srq functionality is now in rdmavt. Remove it from the hfi1 driver. Reviewed-by:
Harish Chegondi <harish.chegondi@intel.com> Signed-off-by:
-
Harish Chegondi authored
Rely on rvt_query_qp function defined in rdmavt Reviewed-by:
-
Dennis Dalessandro authored
Get rid of create and free mad agent from the driver and use rdmavt version. Reviewed-by:
-
Dennis Dalessandro authored
No longer do drivers need to call into the IB core to allocate the verbs device. Use the functionality provided by rdmavt. Reviewed-by:
-
Dennis Dalessandro authored
Now that rdmavt has solidified in its design we can clean up the driver specific register device functions. This handles hfi1. Reviewed-by:
-
Dennis Dalessandro authored
This patch removes the simple post recv function in favor of using rdmavt. The packet receive processing still lives in the driver though. Reviewed-by:
-
Dennis Dalessandro authored
This removes the destroy qp verbs in favor of using rdmavt. Reviewed-by:
-
Dennis Dalessandro authored
In addition to removing the modify queue pair verb from hfi1 we also remove ancillary functions which existed only for modify queue pair and are also already present in hfi1. Reviewed-by:
-
Dennis Dalessandro authored
Multicast is now supported by rdmavt. Remove the verbs multicast functions and use that. Reviewed-by:
-
Dennis Dalessandro authored
This patch removes the post_send and post_one_send from the hfi1 driver. The "posting" of sends will be done by rdmavt which will walk a WQE and queue work. This patch will still provide the capability to schedule that work as well as kick the progress. These are provided to the rdmavt layer. Reviewed-by:
Edward Mascarenhas <edward.mascarenhas@intel.com> Signed-off-by:
-
Dennis Dalessandro authored
Return directly from rvt_resize_cq rather than use a goto/label. Reviewed-by:
-
Dennis Dalessandro authored
The completion queue is not a complex data structure and it can be removed at the same time as its functions. Unlike the more complicated queue pair which was done in multiple patches. This single patch removes all traces of hfi1 specific completeion queues from the hfi1 driver. Reviewed-by:
-
Harish Chegondi authored
Removed hfi1 query_device function to use rdmavt rvt_query_device function The rvt dev info device attributes still need to be filled in by the driver Reviewed-by:
-
Dennis Dalessandro authored
Rely on rdmavt to provide queue pair creation. Reviewed-by:
-
Dennis Dalessandro authored
Another change on the way to removing queue pair functionality from hfi1. This patch removes the private queue pair structure and the table which holds the queue pair numbers in favor of using what is provided by rdmavt. Reviewed-by:
-
Dennis Dalessandro authored
Use the definitions of the s_flags and r_flags which are now in rdmavt. Reviewed-by:
-
Harish Chegondi authored
IB user context alloc and dealloc functions have been added to rdmavt. This patch removes them from hfi1. Reviewed-by:
-
