- 16 Apr, 2010 40 commits
-
-
Luis R. Rodriguez authored
Signed-off-by:
Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Luis R. Rodriguez authored
We can do the family revision check on the top level caller. Signed-off-by:
-
Luis R. Rodriguez authored
Signed-off-by:
-
Luis R. Rodriguez authored
We're bailing out on the alternative code path so remove the else branch. Signed-off-by:
-
Luis R. Rodriguez authored
Signed-off-by:
-
Luis R. Rodriguez authored
Open Loop Control temperature compensation changes between our hardware so use a helper for it. Signed-off-by:
-
Luis R. Rodriguez authored
The code can be simplified and shared between two locations if we bring this into a helper. During reset we do not account for the skip count. Signed-off-by:
-
Senthil Balasubramanian authored
We can reorganize the code in such a way that eep_map can be removed, which makes the code more clearer. Signed-off-by:
Senthil Balasubramanian <senthilkumar@atheros.com> Signed-off-by:
Felix Fietkau <nbd@openwrt.org> Signed-off-by:
-
Felix Fietkau authored
Signed-off-by:
-
Felix Fietkau authored
Signed-off-by:
Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by:
-
Vasanthakumar Thiagarajan authored
Signed-off-by:
-
Vasanthakumar Thiagarajan authored
Signed-off-by:
-
Vasanthakumar Thiagarajan authored
Signed-off-by:
-
Vasanthakumar Thiagarajan authored
Signed-off-by:
-
Vasanthakumar Thiagarajan authored
Signed-off-by:
-
Vasanthakumar Thiagarajan authored
Signed-off-by:
-
Vasanthakumar Thiagarajan authored
Store appropriate desc length which will be used by the ath9k module while duplicating tx desc. Signed-off-by:
-
Luis R. Rodriguez authored
Signed-off-by:
-
Felix Fietkau authored
Signed-off-by:
-
Luis R. Rodriguez authored
Signed-off-by:
-
Luis R. Rodriguez authored
The AR9003 hardware family now initializes hardware by block components and into stages: pre, core and init. Signed-off-by:
-
Luis R. Rodriguez authored
The initvals.h file is over 7000 lines now, so instead of adding AR9003 initvals to it instead lets split the current initvals.h by hardware family: AR5008, AR9001, AR9002 The AR9003 family will have its own initval file later. Signed-off-by:
-
Felix Fietkau authored
Signed-off-by:
-
Felix Fietkau authored
Signed-off-by:
-
Felix Fietkau authored
Signed-off-by:
-
Luis R. Rodriguez authored
Signed-off-by:
-
Felix Fietkau authored
Signed-off-by:
-
Senthil Balasubramanian authored
Also, no need for the udelay(2) on AR9003 hardware. Signed-off-by:
-
Senthil Balasubramanian authored
The AR9003 family requires a change on the loop and can also skip testing the PHY timing registers. This chip test can now be used by all Atheros hardware families, including legacy. We can eventually move this out to the generic ath module. Signed-off-by:
-
Vasanthakumar Thiagarajan authored
* Set rx buf size in register 0x60 * Set rxdp on the respective hw rx queue (HP and LP queues) * Process rx descriptor Signed-off-by:
-
Vasanthakumar Thiagarajan authored
Signed-off-by:
-
Vasanthakumar Thiagarajan authored
Signed-off-by:
-
Vasanthakumar Thiagarajan authored
HP & LP queue depth and rx status length. Signed-off-by:
-
Vasanthakumar Thiagarajan authored
AR9003 supports extended DMA (EDMA), this comes with some bells and whistles on top of the legacy DMA that we are used to. Mark AR9003 and later chips EDMA capable. Signed-off-by:
-
Luis R. Rodriguez authored
Signed-off-by:
-
Luis R. Rodriguez authored
ANI is still being debugged on AR9003 by our systems team so it should not yet be enabled yet. When ANI will be enabled all ANI functionality is expected to be enabled so fill the ANI functionality to all for AR9003 for now as well. Cc: Enis Akay <Enis.Akay@atheros.com> Signed-off-by:
-
Luis R. Rodriguez authored
Signed-off-by:
-
Luis R. Rodriguez authored
This allows us to add SREV checks on these helpers. Signed-off-by:
-
Luis R. Rodriguez authored
This add stubs for PHY support for the AR9003 hardware family. Signed-off-by:
-
Senthil Balasubramanian authored
Also, clean up and reorganize the AR9287 macro to have better ordering. We won't add the PCI ID to the supported device list until we have some functional code for it. Signed-off-by:
-
