This patch adds the support for the L210/L220 (outer) cache
controller. The cache range operations are done by index/way since L2
cache controller only accepts physical addresses.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Other platforms other than SMP may have an outer cache.  For these, we
also need to mark the page table walks outer cacheable.  Since marking
the walks always outer cacheable apparantly has no side effects, we
might as well always mark them so.

However, we continue to only mark PTWs shared if we have SMP enabled.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

In consistent_sync(), start + size can end up pointing one byte
beyond the end of the direct RAM mapping.  We shouldn't BUG() when
this happens.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The DMA cache handling functions take virtual addresses, but in the
form of unsigned long arguments.  This leads to a little confusion
about what exactly they take.  So, convert them to take const void *
instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The outer cache can be L2 as on RealView/EB MPCore platform or even L3
or further on ARMv7 cores. This patch adds the generic support for
flushing the outer cache in the DMA operations.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Memory allocated by the coherent memory allocators will be marked
uncacheable, which means it's pointless calling consistent_sync()
to perform cache maintainence on this memory; it's just a waste of
CPU cycles.

Moreover, with the (subsequent) merge of outer cache support, it
actually breaks things to call consistent_sync() on anything but
direct-mapped memory.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

According to ARM ARM, changes to the CP15 registers are only
guaranteed to be visible after an Instruction Synchronization Barrier
(ISB). This patch adds the ISB at the end of set_cr and
set_copro_access functions and also moves them further down in the
file, below the isb macro definition.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The architecture specification states that TLB operations are
guaranteed to be complete only after the execution of a DSB (Data
Synchronisation Barrier, former Data Write Barrier or Drain Write
Buffer). The branch target cache invalidation is also needed. The ISB
(Instruction Synchronisation Barrier, formerly Prefetch Flush) is
needed unless there will be a return from exception before the
corresponding mapping is used (i.e. user mappings).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

On newer architectures (ARMv6, ARMv7), the depth of the prefetch and
branch prediction is implementation defined and there is a small risk
of wrong ASID tagging when changing TTBR0 before setting the new
context id. The recommended solution is to set a reserved ASID during
TTBR changing. This patch reserves ASID 0.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The ARM Architecture Reference Manual specifies that a prefetch flush
is needed after changing the DACR register (chapter B2.7.6).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

There are three barriers - ISB, DMB and DSB for different
scenarious. This patch adds their definitions in the system.h file.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

bad_mode() currently prints the mode which caused the exception, and
then causes an oops dump to be printed which again displays this
information (since the CPSR in the struct pt_regs is correct.)  This
leads to processor_modes[] being shared between traps.c and process.c
with a local declaration of it.

We can clean this up by moving processor_modes[] to process.c and
removing the duplication, resulting in processor_modes[] becoming
static.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Contec Micro9 (H/M/L) boards based on Cirrus Logic ep93xx (ep9315/ep9307/ep9302).
Signed-off-by: Manfred Gruber <m.gruber@tirol.com>
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

This patch adds the platform resources required to support the
ixp4xx-pata-cf libata driver on Avila Gateworks boards.
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Michael-Luke Jones <mlj28@cam.ac.uk>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

This patch adds support for the Gateworks Avila Network Platform in
a separate set of setup files to the IXDP425. This is necessary now
that a driver for the Avila CF card slot is available. It also adds
support for a minor variant on the Avila board known as the Loft,
which has a different number of maximum PCI devices.
Signed-off-by: Michael-Luke Jones <mlj28@cam.ac.uk>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

This patch removes references to the Gateworks Avila Network
Platform in the ixdp425 setup code. Avila setup should occur
separately now that a CF ATA device driver is available.
Signed-off-by: Michael-Luke Jones <mlj28@cam.ac.uk>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

csum_fold doesn't need two assembly instructions to perform its task,
it can simply add the high and low parts together by rotating by 16
bits, and the carry into the upper-16 bits will automatically happen.

Also, since csum_tcpudp_magic() is just csum_tcpudp_nofold + csum_fold,
use those two functions to achieve this.  Also note that there is a
csum_fold() at the end of ip_fast_csum() as well, so use the real
csum_fold() there as well.

Boot tested on Versatile.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Add the glue for ARM11 SMP oprofile support, which also supports the
performance monitor in the coherency unit.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Add oprofile glue for ARM11 (ARMv6) oprofile support.  This
connects the ARM11 core profiling support to the oprofile code
for uniprocessor configurations.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Add basic support for the ARM11 profiling hardware.  This is shared
between the ARM11 UP and ARM11 SMP oprofile support code.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

When calling into the EFI firmware, the parameters need to be passed on
the stack. The recent change to use -mregparm=3 breaks x86 EFI support.
This patch is needed to allow the new Intel-based Macs to suspend to ram
(efi.get_time is called during the suspend phase).
Signed-off-by: Frederic Riss <frederic.riss@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

That code doesn't do what its author apparently thought it would do...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
  [SCSI] sd: udev accessing an uninitialized scsi_disk field results in a crash
  [SCSI] st: A MTIOCTOP/MTWEOF within the early warning will cause the file number to be incorrect
  [SCSI] qla4xxx: bug fixes
  [SCSI] Fix scsi_add_device() for async scanning

x86-64 is missing these:
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The SN Altix platform does not conform to the IOSAPIC IRQ routing model.
Add code in acpi_unregister_gsi() to check if (acpi_irq_model ==
ACPI_IRQ_MODEL_PLATFORM) and return.

Due to an oversight, this code was not added previously when
similar code was added to acpi_register_gsi().

http://marc.theaimsgroup.com/?l=linux-acpi&m=116680983430121&w=2Signed-off-by: John Keller <jpk@sgi.com>
Acked-by: Len Brown <lenb@kernel.org>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Andrew Vasquez is reporting as-iosched oopses and a 65% throughput
slowdown due to the recent special-casing of direct-io against
blockdevs.  We don't know why either of these things are occurring.

The patch minimally reverts us back to the 2.6.19 code for a 2.6.20
release.

Cc: Andrew Vasquez <andrew.vasquez@qlogic.com>
Cc: Ken Chen <kenchen@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

We went and named them __NR_sys_foo instead of __NR_foo.

It may be too late to change this, but we can at least add the proper names
now.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

smc911x_phy_configure's error handling unconditionally unlocks the
spinlock even if it wasn't locked. Patch fixes it.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This patch fixes up ia64 kexec support for HP rx2620 hardware.  It does
this by skipping migration of already disabled irqs.  This is most likely a
problem on other ia64 platforms as well, but I've only been able to
reproduce it on one machine so far.

The full story is that handle_bad_irq() gets invoked before starting the
new kernel without this patch.  This seems to happen when fixup_irqs()
calls generic_handle_irq() on already migrated (and disabled) irqs.  So by
avoiding migration of disabled irqs we stay away of handle_bad_irq().

The code has been tested on three different ia64 machines, all with good
results.  It is possible to trigger the same bug by offlining a processor
using echo 0 > /sys/devices/system/cpu/cpuX/online.

More detailed information is available in the following mail thread:
http://lists.osdl.org/pipermail/fastboot/2007-January/thread.html#5774Signed-off-by: Magnus Damm <magnus@valinux.co.jp>
Acked-by: Simon Horman <horms@verge.net.au>
Acked-by: Zou, Nanhai <nanhai.zou@intel.com>
Acked-by: Jay Lan <jlan@sgi.com>
Acked-by: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

An AIO bug was reported that sleeping function is being called in softirq
context:

BUG: warning at kernel/mutex.c:132/__mutex_lock_common()
Call Trace:
     [<a000000100577b00>] __mutex_lock_slowpath+0x640/0x6c0
     [<a000000100577ba0>] mutex_lock+0x20/0x40
     [<a0000001000a25b0>] flush_workqueue+0xb0/0x1a0
     [<a00000010018c0c0>] __put_ioctx+0xc0/0x240
     [<a00000010018d470>] aio_complete+0x2f0/0x420
     [<a00000010019cc80>] finished_one_bio+0x200/0x2a0
     [<a00000010019d1c0>] dio_bio_complete+0x1c0/0x200
     [<a00000010019d260>] dio_bio_end_aio+0x60/0x80
     [<a00000010014acd0>] bio_endio+0x110/0x1c0
     [<a0000001002770e0>] __end_that_request_first+0x180/0xba0
     [<a000000100277b90>] end_that_request_chunk+0x30/0x60
     [<a0000002073c0c70>] scsi_end_request+0x50/0x300 [scsi_mod]
     [<a0000002073c1240>] scsi_io_completion+0x200/0x8a0 [scsi_mod]
     [<a0000002074729b0>] sd_rw_intr+0x330/0x860 [sd_mod]
     [<a0000002073b3ac0>] scsi_finish_command+0x100/0x1c0 [scsi_mod]
     [<a0000002073c2910>] scsi_softirq_done+0x230/0x300 [scsi_mod]
     [<a000000100277d20>] blk_done_softirq+0x160/0x1c0
     [<a000000100083e00>] __do_softirq+0x200/0x240
     [<a000000100083eb0>] do_softirq+0x70/0xc0

See report: http://marc.theaimsgroup.com/?l=linux-kernel&m=116599593200888&w=2

flush_workqueue() is not allowed to be called in the softirq context.
However, aio_complete() called from I/O interrupt can potentially call
put_ioctx with last ref count on ioctx and triggers bug.  It is simply
incorrect to perform ioctx freeing from aio_complete.

The bug is trigger-able from a race between io_destroy() and aio_complete().
A possible scenario:

cpu0                               cpu1
io_destroy                         aio_complete
  wait_for_all_aios {                __aio_put_req
     ...                                 ctx->reqs_active--;
     if (!ctx->reqs_active)
        return;
  }
  ...
  put_ioctx(ioctx)

                                     put_ioctx(ctx);
                                        __put_ioctx
                                          bam! Bug trigger!

The real problem is that the condition check of ctx->reqs_active in
wait_for_all_aios() is incorrect that access to reqs_active is not
being properly protected by spin lock.

This patch adds that protective spin lock, and at the same time removes
all duplicate ref counting for each kiocb as reqs_active is already used
as a ref count for each active ioctx.  This also ensures that buggy call
to flush_workqueue() in softirq context is eliminated.
Signed-off-by: "Ken Chen" <kenchen@google.com>
Cc: Zach Brown <zach.brown@oracle.com>
Cc: Suparna Bhattacharya <suparna@in.ibm.com>
Cc: Benjamin LaHaise <bcrl@kvack.org>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Cc: <stable@kernel.org>
Acked-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix this by letting NF_CONNTRACK_H323 depend on (IPV6 || IPV6=n).
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

  CC      net/netfilter/nf_conntrack_netlink.o
net/netfilter/nf_conntrack_netlink.c: In function 'ctnetlink_conntrack_event':
net/netfilter/nf_conntrack_netlink.c:392: error: 'struct nf_conn' has no member named 'mark'
make[3]: *** [net/netfilter/nf_conntrack_netlink.o] Error 1
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

	sd_probe() calls class_device_add() even before initializing the
sdkp->device variable. class_device_add() eventually results in the user mode
udev program to be called. udev program can read the the allow_restart
attribute of the newly created scsi device. This is resulting in a crash as
the show function for allow_restart (i.e sd_show_allow_restart) returns the
attribute value by reading the sdkp->device->allow_restart variable. As the
sdkp->device is not initialized before calling the user mode hotplug helper,
this results in a crash.
	The patch below solves it by calling class_device_add() only after the
necessary fields in the scsi_disk structure are initialized properly.
Signed-off-by: Nagendra Singh Tomar <nagendra_tomar@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  libata: Initialize nbytes for internal sg commands
  libata: Fix ata_busy_wait() kernel docs
  pata_via: Correct missing comments
  pata_atiixp: propogate cable detection hack from drivers/ide to the new driver
  ahci/pata_jmicron: fix JMicron quirk

Some LLDDs, like ipr, use nbytes and pad_len to determine
the total data transfer length of a command. Make sure
nbytes gets initialized for internally generated commands.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

> Looks like you should use ata_busy_wait() here, rather than reproducing
> the same code again.

It waits in 10uS chunks while 1uS chunks were used in the workaround.
Could indeed do that once I know the fix is right. While I'm at it the
ata_busy_wait kerneldoc is borked so here's a fix
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

The 8237S was added to the chipsets but not to the comments. Fix this
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

For all JMicrons except for 361 and 368, AHCI mode enable bits in the
Control(1) should be set.  This used to be done in both ahci and
pata_jmicron but while moving programming to PCI quirk, it was removed
from ahci part while still left in pata_jmicron.

The implemented JMicron PCI quirk was incorrect in that it didn't
program AHCI mode enable bits.  If pata_jmicron is loaded first and
programs those bits, the ahci ports work; otherwise, ahci device
detection fails miserably.

This patch makes JMicron PCI quirk clear SATA IDE mode bits and set
AHCI mode bits and remove the respective part from pata_jmicron.
Tested on JMB361, 363 and 368.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>