Sven Auhagen reported issues with negotiation on a couple of his
platforms using a mixture of SFP and PHYs in various different
modes.  Debugging to root cause proved difficult, but essentially
the problem comes down to the mvpp2 phylink implementation being
slightly at odds with what is expected.

phylink operates in three modes: phy, fixed-link, and in-band mode.

In the first two modes, the expected behaviour from a MAC driver is
that phylink resolves the operating mode and passes the mode to the
MAC driver for it to program, including when the link should be
brought up or taken down.  This is basically the same as the libphy
approach.  This does not negate the requirement to advertise a correct
control word for interface modes that have control words where that
can be reasonably controlled.

The second mode is in-band mode, where the MAC is expected to use the
in-band control word to determine the operating mode.

The mvneta driver implements the correct pattern required to support
this: configure the port interface type separately from the in-band
mode(s).  This is now specified in the phylink documentation patches.

mvpp2 was programming in-band mode for SGMII and the 802.3z modes no
what, and avoided forcing the link up in fixed/phy modes.  This caused
a problem with some boards where the PHY is by default programmed to
enter AN bypass mode, the PHY would report that the link was up, but
the mvpp2 never completed the exchange of control word.

Another issue that mvpp2 has is it sets SGMII AN format control word
for both SGMII and 802.3z modes. The format of the control word is
defined by MVPP2_GMAC_INBAND_AN_MASK, which should be set for SGMII
and clear for 802.3z. Available Marvell documentation for earlier
GMAC implementations does not make this clear, but this has been
ascertained via extensive testing on earlier GMAC implementations,
and then confirmed with a Macchiatobin Single Shot connected to a
Clearfog: when MVPP2_GMAC_INBAND_AN_MASK is set, the clearfog does
not receive the advertised pause mode settings.

Lastly, there is no flow control in the in-band control word in Cisco
SGMII, setting the flow control autonegotiation bit even with a PHY
that has the Marvell extension to send this information does not result
in the flow control being enabled at the MAC.  We need to do this
manually using the information provided via phylink.

Re-code mvpp2's mac_config() and mac_link_up() to follow this pattern.
This allows Sven Auhagen's board and Macchiatobin to reliably bring
the link up with the 88e1512 PHY with phylink operating in PHY mode
with COMPHY built as a module but the rest of the networking built-in,
and u-boot having brought up the interface.  in-band mode requires an
additional patch to resolve another problem.
Tested-by: Sven Auhagen <sven.auhagen@voleatech.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/core/ethtool.c:3023:19: warning: address of array
'ext_m_spec->h_dest' will always evaluate to 'true'
[-Wpointer-bool-conversion]
                if (ext_m_spec->h_dest) {
                ~~  ~~~~~~~~~~~~^~~~~~

h_dest is an array, it can't be null so remove this check.

Fixes: eca4205f ("ethtool: add ethtool_rx_flow_spec to flow_rule structure translator")
Link: https://github.com/ClangBuiltLinux/linux/issues/353Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:

struct foo {
    int stuff;
    struct boo entry[];
};

size = sizeof(struct foo) + count * sizeof(struct boo);
instance = kzalloc(size, GFP_KERNEL);

Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:

instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);

Notice that, in this case, variable size is not necessary, hence
it is removed.

This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:

struct foo {
    int stuff;
    struct boo entry[];
};

size = sizeof(struct foo) + count * sizeof(struct boo);
instance = kzalloc(size, GFP_KERNEL)

Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:

instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL)

Notice that, in this case, variable size is not necessary, hence
it is removed.

This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:

struct foo {
    int stuff;
    struct boo entry[];
};

size = sizeof(struct foo) + count * sizeof(struct boo);
instance = alloc(size, GFP_KERNEL);

Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:

size = struct_size(instance, entry, count);

This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The link status register latches link-down events. Therefore, if link
is reported as being up, there's no need for a second read.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:

struct foo {
    int stuff;
    struct boo entry[];
};

size = sizeof(struct foo) + count * sizeof(struct boo);
instance = kzalloc(size, GFP_KERNEL);

Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:

instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);

Notice that, in this case, variable size is not necessary, hence
it is removed.

This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:

struct foo {
    int stuff;
    void *entry[];
};

size = sizeof(struct foo) + count * sizeof(void *);
instance = alloc(size, GFP_KERNEL);

Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:

instance = alloc(struct_size(instance, entry, count), GFP_KERNEL);

Notice that, in this case, variable size is not necessary, hence
it is removed.

This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:

struct foo {
    int stuff;
    struct boo entry[];
};

size = sizeof(struct foo) + count * sizeof(struct boo);
instance = kzalloc(size, GFP_KERNEL)

Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:

instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL)

Notice that, in this case, variable alloc_size is not necessary, hence
it is removed.

This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:

struct foo {
    int stuff;
    struct boo entry[];
};

size = sizeof(struct foo) + count * sizeof(struct boo);
instance = kzalloc(size, GFP_KERNEL)

Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:

instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL)

Notice that, in this case, variable fsz is not necessary, hence
it is removed.

This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:

struct foo {
    int stuff;
    void *entry[];
};

size = sizeof(struct foo) + count * sizeof(void *);
instance = alloc(size, GFP_KERNEL);

Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:

size = struct_size(instance, entry, count);

This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:

struct foo {
    int stuff;
    struct boo entry[];
};

size = sizeof(struct foo) + count * sizeof(struct boo);
instance = alloc(size, GFP_KERNEL)

Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:

instance = alloc(struct_size(instance, entry, count), GFP_KERNEL)

Notice that, in this case, variable alloc_size is not necessary, hence
it is removed.

This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:

struct foo {
    int stuff;
    void *entry[];
};

instance = alloc(sizeof(struct foo) + count * sizeof(void *));

Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:

instance = alloc(struct_size(instance, entry, count));

This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:

struct foo {
    int stuff;
    struct boo entry[];
};

size = sizeof(struct foo) + count * sizeof(struct boo);
instance = alloc(size, GFP_KERNEL)

Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:

instance = alloc(struct_size(instance, entry, count), GFP_KERNEL)

Notice that, in this case, variable size is not necessary, hence it is
removed.

This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:

struct foo {
    int stuff;
    struct boo entry[];
};

instance = alloc(sizeof(struct foo) + count * sizeof(struct boo));

Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:

instance = alloc(struct_size(instance, entry, count));

This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:

struct foo {
    int stuff;
    struct boo entry[];
};

size = sizeof(struct foo) + count * sizeof(struct boo);
instance = alloc(size, GFP_KERNEL)

Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:

size = struct_size(instance, entry, count);
instance = alloc(size, GFP_KERNEL)

This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:

struct foo {
    int stuff;
    struct boo entry[];
};

size = sizeof(struct foo) + count * sizeof(struct boo);
instance = alloc(size, GFP_KERNEL)

Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:

size = struct_size(instance, entry, count);

This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sudarsana Reddy Kalluru says:

====================
qed*: SmartAN query support

SmartAN feature detects the peer/cable capabilities and establishes the
link in the best possible configuration.
The patch series adds support for querying the capability. Please consider
applying it net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The patch adds driver support to query SmartAN capability via ethtool.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Michal Kalderon <mkalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The patch adds driver interface to read the SmartAN capability from
management firmware.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Michal Kalderon <mkalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: dsa: bcm_sf2: Add support for CFP statistics

The Broadcom SF2 switch has a Compact Field Processor (CFP) which not
only can perform matching + action, but also counts the number of times
a rule has been hit. This is invaluable while debugging when/if rules
are not matched.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When the source and destination port of a CFP rule match, we must set
the loopback bit enable to allow that, otherwise the frame is discarded.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Return CFP policer statistics (Green, Yellow or Red) as part of the
standard ethtool statistics. This helps debug when CFP rules may not be
hit (0 counter).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation for adding CFP statistics, we will need to overlay the
standard B53 statistics, so create specific bcm_sf2_sw_* functions to
call into their b53_common.c counterpart.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We no longer need a dedicated statistics mutex since we leverage
b53_common for statistics now.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The link status value latches link-down events. To get the current
status we read the register twice in genphy_update_link(). There's
a potential risk that we miss a link-down event in polling mode.
This may cause issues if the user e.g. connects his machine to a
different network.

On the other hand reading the latched value may cause issues in
interrupt mode. Following scenario:

- After boot link goes up
- phy_start() is called triggering an aneg restart, hence link goes
  down and link-down info is latched.
- After aneg has finished link goes up and triggers an interrupt.
  Interrupt handler reads link status, means it reads the latched
  "link is down" info. But there won't be another interrupt as long
  as link stays up, therefore phylib will never recognize that link
  is up.

Deal with both scenarios by reading the register twice in interrupt
mode only.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a new compatibility string for this product. It's using
at91sam9260-macb layout but has a newer hardware revision: it's safer
to use its own string.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the compatibility sting documentation for sam9x60 10/100 interface.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This removes a line left while adding the correct compatibility string for
sama5d3 10/100 interface. Now use the "atmel,sama5d3-macb" string.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
mlxsw: Implement periodic ERP rehash

Currently, an ERP set is created for each region according to rules
inserted and order of their insertion. However that might lead to
suboptimal ERP sets and possible unnecessary spillage into C-TCAM.
This patchset aims to fix this problem and introduces periodical checking
of used ERP sets and in case a better ERP set is possible for the given
set of rules, it rehashes the region to use the better ERP set.

Patch 1 prepares devlink params infra in order to fix the
        init/fini sequences.
Patch 2 implements hints infra in objagg library.
Patch 3 fixes a typo
Patch 4 adds number of root objects directly into objagg stats.
Patches 5-7 do split of multiple structs in Spectrum TCAM code.
Patch 8 introduces initial implementation of ERP rehash logic,
         according to objagg hints.
Patch 9 adds hints priv passing trought the layers.
Patch 10 adds multi field into PAGT reg. (new patch)
Patch 11 implements actual region rules migration in TCAM code.
Patch 12 adds a devlink param so user is able to control
         rehash interval.
Patch 13 adds couple of tracepoints in order to track
         rehash procedures.
Patch 14 adds a simple selftest to test region rehash.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Track the basic codepaths of delta rehash handling,
using mlxsw tracepoints.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As vregion rehash is happening in delayed work, add some visibility to
the process using a few tracepoints.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Expose new driver-specific "acl_region_rehash_interval" devlink param
which would allow user to alter default ACL region rehash interval.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the hints are returned, the migration should be started. For that to
happen, there is a need to create a second physical region in TCAM with
new ERP set by passing the hints and then move chunk by chunk,
entry by entry.

During the transition, two lookups will occur. One in old region and
another in new region. The highest priority rule will be chosen.

In an unlikely case that the migration will fail and also rollback to
original region will fail the vregion will become in bad state.
Everything will work, only no future rehash will be possible. In a
follow-up work, this can be resolved by trying to resume the rollback
in delayed work and repair the vregion.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For Spectrum-2 this allows parallel lookups in multiple regions.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The hints priv comes from ERP code and it is possible to obtain it from
TCAM code. Add arg to appropriate functions so the hints
priv could be passed back down to ERP code. Pass NULL now as the
follow-up patches would pass an actual hints priv pointer.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Introduce an initial implementation of rehash logic in ERP code.
Currently, the rehash is considered as needed only in case number of
roots in the hints is smaller than the number of roots actually in use.
In that case return hints pointer and let it be obtained through the
callpath through the Spectrum-2 TCAM op.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Do the split of entry struct so the new entry struct is related to the
actual HW entry, whereas ventry struct is a SW abstration of that.
This split prepares possibility for ventry to hold 2 HW entries which
is needed for region ERP rehash flow.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Do the split of chunk struct so the new chunk struct is related to the
actual HW chunk (differs between Spectrum and Spectrum-2),
whereas vchunk struct is a SW abstraction of that. This split
prepares possibility for vchunk to hold 2 HW chunks which is needed
for region ERP rehash flow.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Do the split of region struct so the new region struct is related to the
actual HW region, whereas vregion struct is a SW abstration of that.
This split prepares possibility for vregion to hold 2 HW regions which
is needed for region ERP rehash flow.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>