- 29 Jun, 2017 29 commits
-
-
Nicholas Bellinger authored
commit abb85a9b upstream. When iscsi WRITE underflow occurs there are two different scenarios that can happen. Normally in practice, when an EDTL vs. SCSI CDB TRANSFER LENGTH underflow is detected, the iscsi immediate data payload is the smaller SCSI CDB TRANSFER LENGTH. That is, when a host fabric LLD is using a fixed size EDTL for a specific control CDB, the SCSI CDB TRANSFER LENGTH and actual SCSI payload ends up being smaller than EDTL. In iscsi, this means the received iscsi immediate data payload matches the smaller SCSI CDB TRANSFER LENGTH, because there is no more SCSI payload to accept beyond SCSI CDB TRANSFER LENGTH. However, it's possible for a malicous host to send a WRITE underflow where EDTL is larger than SCSI CDB TRANSFER LENGTH, but incoming iscsi immediate data actually matches EDTL. In the wild, we've never had a iscsi host environment actually try to do this. For this special case, it's wrong to truncate part of the control CDB payload and continue to process the command during underflow when immediate data payload received was larger than SCSI CDB TRANSFER LENGTH, so go ahead and reject and drop the bogus payload as a defensive action. Note this potential bug was originally relaxed by the following for allowing WRITE underflow in MSFT FCP host environments: commit c72c5250 Author: Roland Dreier <roland@purestorage.com> Date: Wed Jul 22 15:08:18 2015 -0700 target: allow underflow/overflow for PR OUT etc. commands Cc: Roland Dreier <roland@purestorage.com> Cc: Mike Christie <mchristi@redhat.com> Cc: Hannes Reinecke <hare@suse.de> Cc: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Nicholas Bellinger authored
commit 105fa2f4 upstream. This patch fixes a BUG() in iscsit_close_session() that could be triggered when iscsit_logout_post_handler() execution from within tx thread context was not run for more than SECONDS_FOR_LOGOUT_COMP (15 seconds), and the TCP connection didn't already close before then forcing tx thread context to automatically exit. This would manifest itself during explicit logout as: [33206.974254] 1 connection(s) still exist for iSCSI session to iqn.1993-08.org.debian:01:3f5523242179 [33206.980184] INFO: NMI handler (kgdb_nmi_handler) took too long to run: 2100.772 msecs [33209.078643] ------------[ cut here ]------------ [33209.078646] kernel BUG at drivers/target/iscsi/iscsi_target.c:4346! Normally when explicit logout attempt fails, the tx thread context exits and iscsit_close_connection() from rx thread context does the extra cleanup once it detects conn->conn_logout_remove has not been cleared by the logout type specific post handlers. To address this special case, if the logout post handler in tx thread context detects conn->tx_thread_active has already been cleared, simply return and exit in order for existing iscsit_close_connection() logic from rx thread context do failed logout cleanup. Reported-by:
Bart Van Assche <bart.vanassche@sandisk.com> Tested-by:
Gary Guo <ghg@datera.io> Tested-by:
Chu Yuan Lin <cyl@datera.io> Signed-off-by:
-
Nicholas Bellinger authored
commit 73d4e580 upstream. This patch fixes a se_cmd->cmd_kref underflow during CMD_T_ABORTED when a fabric driver drops it's second reference from below the target_core_tmr.c based callers of transport_cmd_finish_abort(). Recently with the conversion of kref to refcount_t, this bug was manifesting itself as: [705519.601034] refcount_t: underflow; use-after-free. [705519.604034] INFO: NMI handler (kgdb_nmi_handler) took too long to run: 20116.512 msecs [705539.719111] ------------[ cut here ]------------ [705539.719117] WARNING: CPU: 3 PID: 26510 at lib/refcount.c:184 refcount_sub_and_test+0x33/0x51 Since the original kref atomic_t based kref_put() didn't check for underflow and only invoked the final callback when zero was reached, this bug did not manifest in practice since all se_cmd memory is using preallocated tags. To address this, go ahead and propigate the existing return from transport_put_cmd() up via transport_cmd_finish_abort(), and change transport_cmd_finish_abort() + core_tmr_handle_tas_abort() callers to only do their local target_put_sess_cmd() if necessary. Reported-by:
-
Will Deacon authored
commit dbb236c1 upstream. Recently vDSO support for CLOCK_MONOTONIC_RAW was added in 49eea433 ("arm64: Add support for CLOCK_MONOTONIC_RAW in clock_gettime() vDSO"). Noticing that the core timekeeping code never set tkr_raw.xtime_nsec, the vDSO implementation didn't bother exposing it via the data page and instead took the unshifted tk->raw_time.tv_nsec value which was then immediately shifted left in the vDSO code. Unfortunately, by accellerating the MONOTONIC_RAW clockid, it uncovered potential 1ns time inconsistencies caused by the timekeeping core not handing sub-ns resolution. Now that the core code has been fixed and is actually setting tkr_raw.xtime_nsec, we need to take that into account in the vDSO by adding it to the shifted raw_time value, in order to fix the user-visible inconsistency. Rather than do that at each use (and expand the data page in the process), instead perform the shift/addition operation when populating the data page and remove the shift from the vDSO code entirely. [jstultz: minor whitespace tweak, tried to improve commit message to make it more clear this fixes a regression] Reported-by:
John Stultz <john.stultz@linaro.org> Signed-off-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
Daniel Mentz <danielmentz@google.com> Acked-by:
Kevin Brodsky <kevin.brodsky@arm.com> Cc: Prarit Bhargava <prarit@redhat.com> Cc: Richard Cochran <richardcochran@gmail.com> Cc: Stephen Boyd <stephen.boyd@linaro.org> Cc: Miroslav Lichvar <mlichvar@redhat.com> Link: http://lkml.kernel.org/r/1496965462-20003-4-git-send-email-john.stultz@linaro.orgSigned-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
John Stultz authored
commit 3d88d56c upstream. Due to how the MONOTONIC_RAW accumulation logic was handled, there is the potential for a 1ns discontinuity when we do accumulations. This small discontinuity has for the most part gone un-noticed, but since ARM64 enabled CLOCK_MONOTONIC_RAW in their vDSO clock_gettime implementation, we've seen failures with the inconsistency-check test in kselftest. This patch addresses the issue by using the same sub-ns accumulation handling that CLOCK_MONOTONIC uses, which avoids the issue for in-kernel users. Since the ARM64 vDSO implementation has its own clock_gettime calculation logic, this patch reduces the frequency of errors, but failures are still seen. The ARM64 vDSO will need to be updated to include the sub-nanosecond xtime_nsec values in its calculation for this issue to be completely fixed. Signed-off-by:
-
John Stultz authored
commit ceea5e37 upstream. In tests, which excercise switching of clocksources, a NULL pointer dereference can be observed on AMR64 platforms in the clocksource read() function: u64 clocksource_mmio_readl_down(struct clocksource *c) { return ~(u64)readl_relaxed(to_mmio_clksrc(c)->reg) & c->mask; } This is called from the core timekeeping code via: cycle_now = tkr->read(tkr->clock); tkr->read is the cached tkr->clock->read() function pointer. When the clocksource is changed then tkr->clock and tkr->read are updated sequentially. The code above results in a sequential load operation of tkr->read and tkr->clock as well. If the store to tkr->clock hits between the loads of tkr->read and tkr->clock, then the old read() function is called with the new clock pointer. As a consequence the read() function dereferences a different data structure and the resulting 'reg' pointer can point anywhere including NULL. This problem was introduced when the timekeeping code was switched over to use struct tk_read_base. Before that, it was theoretically possible as well when the compiler decided to reload clock in the code sequence: now = tk->clock->read(tk->clock); Add a helper function which avoids the issue by reading tk_read_base->clock once into a local variable clk and then issue the read function via clk->read(clk). This guarantees that the read() function always gets the proper clocksource pointer handed in. Since there is now no use for the tkr.read pointer, this patch also removes it, and to address stopping the fast timekeeper during suspend/resume, it introduces a dummy clocksource to use rather then just a dummy read function. Signed-off-by:
Ingo Molnar <mingo@kernel.org> Cc: Prarit Bhargava <prarit@redhat.com> Cc: Richard Cochran <richardcochran@gmail.com> Cc: Stephen Boyd <stephen.boyd@linaro.org> Cc: Miroslav Lichvar <mlichvar@redhat.com> Cc: Daniel Mentz <danielmentz@google.com> Link: http://lkml.kernel.org/r/1496965462-20003-2-git-send-email-john.stultz@linaro.orgSigned-off-by:
-
Arend Van Spriel authored
commit 7a51461f upstream. When request firmware fails, brcmf_ops_sdio_remove is being called and brcmf_bus freed. In such circumstancies if you do a suspend/resume cycle the kernel hangs on resume due a NULL pointer dereference in resume function. So in brcmf_sdio_firmware_callback() we need to unbind the driver from both sdio_func devices when firmware load failure is indicated. Tested-by:
Enric Balletbo i Serra <enric.balletbo@collabora.com> Reviewed-by:
Hante Meuleman <hante.meuleman@broadcom.com> Reviewed-by:
Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com> Reviewed-by:
Franky Lin <franky.lin@broadcom.com> Signed-off-by:
Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Signed-off-by:
-
Arend Van Spriel authored
commit 03fb0e83 upstream. When firmware loading failed the code used to unbind the device provided by the calling code. However, for the sdio driver two devices are bound and both need to be released upon failure. The callback has been extended with parameter to pass error code so add that in this commit upon firmware loading failure. Reviewed-by:
-
Arend Van Spriel authored
commit 6d0507a7 upstream. Extend the parameters in the firmware callback so it can be called upon success and failure. This allows the caller to properly clear all resources in the failure path. Right now the error code is always zero, ie. success. Reviewed-by:
-
Daniel Drake authored
commit 817ae460 upstream. Without this quirk, the touchpad is not responsive on this product, with the following message repeated in the logs: psmouse serio1: bad data from KBC - timeout Add it to the notimeout list alongside other similar Fujitsu laptops. Signed-off-by:
Daniel Drake <drake@endlessm.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Naveen N. Rao authored
commit d89ba535 upstream. On Power9, trying to use data breakpoints throws the splat shown below. This is because the check for a data breakpoint in DSISR is in do_hash_page(), which is not called when in Radix mode. Unable to handle kernel paging request for data at address 0xc000000000e19218 Faulting instruction address: 0xc0000000001155e8 cpu 0x0: Vector: 300 (Data Access) at [c0000000ef1e7b20] pc: c0000000001155e8: find_pid_ns+0x48/0xe0 lr: c000000000116ac4: find_task_by_vpid+0x44/0x90 sp: c0000000ef1e7da0 msr: 9000000000009033 dar: c000000000e19218 dsisr: 400000 Move the check to handle_page_fault() so as to catch data breakpoints in both Hash and Radix MMU modes. We have to change the check in do_hash_page() against 0xa410 to use 0xa450, so as to include the value of (DSISR_DABRMATCH << 16). There are two sites that call handle_page_fault() when in Radix, both already pass DSISR in r4. Fixes: caca285e ("powerpc/mm/radix: Use STD_MMU_64 to properly isolate hash related code") Reported-by:
Shriya R. Kulkarni <shriykul@in.ibm.com> Signed-off-by:
Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> [mpe: Fix the fall-through case on hash, we need to reload DSISR] Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Naveen N. Rao authored
commit a9f8553e upstream. This fixes a crash when function_graph and jprobes are used together. This is essentially commit 237d28db ("ftrace/jprobes/x86: Fix conflict between jprobes and function graph tracing"), but for powerpc. Jprobes breaks function_graph tracing since the jprobe hook needs to use jprobe_return(), which never returns back to the hook, but instead to the original jprobe'd function. The solution is to momentarily pause function_graph tracing before invoking the jprobe hook and re-enable it when returning back to the original jprobe'd function. Fixes: 6794c782 ("powerpc64: port of the function graph tracer") Signed-off-by:
Masami Hiramatsu <mhiramat@kernel.org> Acked-by:
Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by:
-
Eric W. Biederman authored
commit 57db7e4a upstream. Thomas Gleixner wrote: > The CRIU support added a 'feature' which allows a user space task to send > arbitrary (kernel) signals to itself. The changelog says: > > The kernel prevents sending of siginfo with positive si_code, because > these codes are reserved for kernel. I think we can allow a task to > send such a siginfo to itself. This operation should not be dangerous. > > Quite contrary to that claim, it turns out that it is outright dangerous > for signals with info->si_code == SI_TIMER. The following code sequence in > a user space task allows to crash the kernel: > > id = timer_create(CLOCK_XXX, ..... signo = SIGX); > timer_set(id, ....); > info->si_signo = SIGX; > info->si_code = SI_TIMER: > info->_sifields._timer._tid = id; > info->_sifields._timer._sys_private = 2; > rt_[tg]sigqueueinfo(..., SIGX, info); > sigemptyset(&sigset); > sigaddset(&sigset, SIGX); > rt_sigtimedwait(sigset, info); > > For timers based on CLOCK_PROCESS_CPUTIME_ID, CLOCK_THREAD_CPUTIME_ID this > results in a kernel crash because sigwait() dequeues the signal and the > dequeue code observes: > > info->si_code == SI_TIMER && info->_sifields._timer._sys_private != 0 > > which triggers the following callchain: > > do_schedule_next_timer() -> posix_cpu_timer_schedule() -> arm_timer() > > arm_timer() executes a list_add() on the timer, which is already armed via > the timer_set() syscall. That's a double list add which corrupts the posix > cpu timer list. As a consequence the kernel crashes on the next operation > touching the posix cpu timer list. > > Posix clocks which are internally implemented based on hrtimers are not > affected by this because hrtimer_start() can handle already armed timers > nicely, but it's a reliable way to trigger the WARN_ON() in > hrtimer_forward(), which complains about calling that function on an > already armed timer. This problem has existed since the posix timer code was merged into 2.5.63. A few releases earlier in 2.5.60 ptrace gained the ability to inject not just a signal (which linux has supported since 1.0) but the full siginfo of a signal. The core problem is that the code will reschedule in response to signals getting dequeued not just for signals the timers sent but for other signals that happen to a si_code of SI_TIMER. Avoid this confusion by testing to see if the queued signal was preallocated as all timer signals are preallocated, and so far only the timer code preallocates signals. Move the check for if a timer needs to be rescheduled up into collect_signal where the preallocation check must be performed, and pass the result back to dequeue_signal where the code reschedules timers. This makes it clear why the code cares about preallocated timers. Reported-by:
"Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by:
-
Sebastian Parschauer authored
commit 3db28271 upstream. This mouse is also known under other IDs. It needs the quirk ALWAYS_POLL or will disconnect in runlevel 1 or 3. Signed-off-by:
Sebastian Parschauer <sparschauer@suse.de> Signed-off-by:
Jiri Kosina <jkosina@suse.cz> Signed-off-by:
-
Raju Rangoju authored
commit dec6b331 upstream. During the module initialisation there is a possible race (basically race between uld and lld) where neither the uld nor lld notifies the uP about where to route the ctrl queue completions. LLD skips notifying uP as the rdma queues were not created by then (will leave it to ULD to notify the uP). As the ULD comes up, it also skips notifying the uP as the flag FULL_INIT_DONE is not set yet (ULD assumes that the interface is not up yet). Consequently, this race between uld and lld leaves uP unnotified about where to send the ctrl queue completions to, leading to iwarp RI_RES WR failure. Here is the race: CPU 0 CPU1 - allocates nic rx queus - t4_sge_alloc_ctrl_txq() (if rdma rsp queues exists, tell uP to route ctrl queue compl to rdma rspq) - acquires the mutex_lock - allocates rdma response queues - if FULL_INIT_DONE set, tell uP to route ctrl queue compl to rdma rspq - relinquishes mutex_lock - acquires the mutex_lock - enable_rx() - set FULL_INIT_DONE - relinquishes mutex_lock This patch fixes the above issue. Fixes: e7519f99('cxgb4: avoid enabling napi twice to the same queue') Signed-off-by:
Raju Rangoju <rajur@chelsio.com> Acked-by:
Steve Wise <swise@opengridcomputing.com> Signed-off-by:
Ganesh Goudar <ganeshgr@chelsio.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Pavel Shilovsky authored
commit dcd87838 upstream. Downgrade the loglevel for SMB2 to prevent filling the log with messages if e.g. readdir was interrupted. Also make SMB2 and SMB1 codepaths do the same logging during readdir. Signed-off-by:
Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by:
Steve French <smfrench@gmail.com> Signed-off-by:
-
Paul Mackerras authored
commit ca8efa1d upstream. This adds code to save the values of three SPRs (special-purpose registers) used by userspace to control event-based branches (EBBs), which are essentially interrupts that get delivered directly to userspace. These registers are loaded up with guest values when entering the guest, and their values are saved when exiting the guest, but we were not saving the host values and restoring them before going back to userspace. On POWER8 this would only affect userspace programs which explicitly request the use of EBBs and also use the KVM_RUN ioctl, since the only source of EBBs on POWER8 is the PMU, and there is an explicit enable bit in the PMU registers (and those PMU registers do get properly context-switched between host and guest). On POWER9 there is provision for externally-generated EBBs, and these are not subject to the control in the PMU registers. Since these registers only affect userspace, we can save them when we first come in from userspace and restore them before returning to userspace, rather than saving/restoring the host values on every guest entry/exit. Similarly, we don't need to worry about their values on offline secondary threads since they execute in the context of the idle task, which never executes in userspace. Fixes: b005255e ("KVM: PPC: Book3S HV: Context-switch new POWER8 SPRs", 2014-01-08) Signed-off-by:
Paul Mackerras <paulus@ozlabs.org> Signed-off-by:
-
Paul Mackerras authored
commit 46a704f8 upstream. If userspace attempts to call the KVM_RUN ioctl when it has hardware transactional memory (HTM) enabled, the values that it has put in the HTM-related SPRs TFHAR, TFIAR and TEXASR will get overwritten by guest values. To fix this, we detect this condition and save those SPR values in the thread struct, and disable HTM for the task. If userspace goes to access those SPRs or the HTM facility in future, a TM-unavailable interrupt will occur and the handler will reload those SPRs and re-enable HTM. If userspace has started a transaction and suspended it, we would currently lose the transactional state in the guest entry path and would almost certainly get a "TM Bad Thing" interrupt, which would cause the host to crash. To avoid this, we detect this case and return from the KVM_RUN ioctl with an EINVAL error, with the KVM exit reason set to KVM_EXIT_FAIL_ENTRY. Fixes: b005255e ("KVM: PPC: Book3S HV: Context-switch new POWER8 SPRs", 2014-01-08) Signed-off-by:
-
Heiko Carstens authored
commit addb63c1 upstream. For real-space designation asces the asce origin part is only a token. The asce token origin must not be used to generate an effective address for storage references. This however is erroneously done within kvm_s390_shadow_tables(). Furthermore within the same function the wrong parts of virtual addresses are used to generate a corresponding real address (e.g. the region second index is used as region first index). Both of the above can result in incorrect address translations. Only for real space designations with a token origin of zero and addresses below one megabyte the translation was correct. Furthermore replace a "!asce.r" statement with a "!*fake" statement to make it more obvious that a specific condition has nothing to do with the architecture, but with the fake handling of real space designations. Fixes: 3218f709 ("s390/mm: support real-space for gmap shadows") Cc: David Hildenbrand <david@redhat.com> Signed-off-by:
Heiko Carstens <heiko.carstens@de.ibm.com> Reviewed-by:
Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by:
Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by:
-
Kan Liang authored
commit fb3a5055 upstream. Current DTLB load/store miss events (0x608/0x649) only counts 4K,2M and 4M page size. Need to extend the events to support any page size (4K/2M/4M/1G). The complete DTLB load/store miss events are: DTLB_LOAD_MISSES.WALK_COMPLETED 0xe08 DTLB_STORE_MISSES.WALK_COMPLETED 0xe49 Signed-off-by:
Kan Liang <Kan.liang@intel.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: eranian@google.com Link: http://lkml.kernel.org/r/20170619142609.11058-1-kan.liang@intel.comSigned-off-by:
-
Ilya Matveychikov authored
commit a91e0f68 upstream. When using get_options() it's possible to specify a range of numbers, like 1-100500. The problem is that it doesn't track array size while calling internally to get_range() which iterates over the range and fills the memory with numbers. Link: http://lkml.kernel.org/r/2613C75C-B04D-4BFF-82A6-12F97BA0F620@gmail.comSigned-off-by:
Ilya V. Matveychikov <matvejchikov@gmail.com> Cc: Jonathan Corbet <corbet@lwn.net> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
NeilBrown authored
commit 9fa4eb8e upstream. If a positive status is passed with the AUTOFS_DEV_IOCTL_FAIL ioctl, autofs4_d_automount() will return ERR_PTR(status) with that status to follow_automount(), which will then dereference an invalid pointer. So treat a positive status the same as zero, and map to ENOENT. See comment in systemd src/core/automount.c::automount_send_ready(). Link: http://lkml.kernel.org/r/871sqwczx5.fsf@notabene.neil.brown.nameSigned-off-by:
NeilBrown <neilb@suse.com> Cc: Ian Kent <raven@themaw.net> Signed-off-by:
-
Ravi Bangoria authored
commit bf05fc25 upstream. When a kthread calls call_usermodehelper() the steps are: 1. allocate current->mm 2. load_elf_binary() 3. populate current->thread.regs While doing this, interrupts are not disabled. If there is a perf interrupt in the middle of this process (i.e. step 1 has completed but not yet reached to step 3) and if perf tries to read userspace regs, kernel oops with following log: Unable to handle kernel paging request for data at address 0x00000000 Faulting instruction address: 0xc0000000000da0fc ... Call Trace: perf_output_sample_regs+0x6c/0xd0 perf_output_sample+0x4e4/0x830 perf_event_output_forward+0x64/0x90 __perf_event_overflow+0x8c/0x1e0 record_and_restart+0x220/0x5c0 perf_event_interrupt+0x2d8/0x4d0 performance_monitor_exception+0x54/0x70 performance_monitor_common+0x158/0x160 --- interrupt: f01 at avtab_search_node+0x150/0x1a0 LR = avtab_search_node+0x100/0x1a0 ... load_elf_binary+0x6e8/0x15a0 search_binary_handler+0xe8/0x290 do_execveat_common.isra.14+0x5f4/0x840 call_usermodehelper_exec_async+0x170/0x210 ret_from_kernel_thread+0x5c/0x7c Fix it by setting abi to PERF_SAMPLE_REGS_ABI_NONE when userspace pt_regs are not set. Fixes: ed4a4ef8 ("powerpc/perf: Add support for sampling interrupt register state") Signed-off-by:
Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com> Acked-by:
-
Kees Cook authored
commit 98da7d08 upstream. When limiting the argv/envp strings during exec to 1/4 of the stack limit, the storage of the pointers to the strings was not included. This means that an exec with huge numbers of tiny strings could eat 1/4 of the stack limit in strings and then additional space would be later used by the pointers to the strings. For example, on 32-bit with a 8MB stack rlimit, an exec with 1677721 single-byte strings would consume less than 2MB of stack, the max (8MB / 4) amount allowed, but the pointers to the strings would consume the remaining additional stack space (1677721 * 4 == 6710884). The result (1677721 + 6710884 == 8388605) would exhaust stack space entirely. Controlling this stack exhaustion could result in pathological behavior in setuid binaries (CVE-2017-1000365). [akpm@linux-foundation.org: additional commenting from Kees] Fixes: b6a2fea3 ("mm: variable length argument support") Link: http://lkml.kernel.org/r/20170622001720.GA32173@beastSigned-off-by:
Kees Cook <keescook@chromium.org> Acked-by:
Rik van Riel <riel@redhat.com> Acked-by:
Michal Hocko <mhocko@suse.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Qualys Security Advisory <qsa@qualys.com> Signed-off-by:
-
Takashi Iwai authored
commit 2deaeaf1 upstream. The standard PCM chmap helper callbacks treat the NULL info->chmap as a fatal error and spews the kernel warning with stack trace when CONFIG_SND_DEBUG is on. This was OK, originally it was supposed to be always static and non-NULL. But, as the recent addition of Intel LPE audio driver shows, the chmap content may vary dynamically, and it can be even NULL when disconnected. The user still sees the kernel warning unnecessarily. For clearing such a confusion, this patch simply removes the snd_BUG_ON() in each place, just returns an error without warning. Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Takashi Sakamoto authored
commit 4a9bfafc upstream. At Linux v3.5, packet processing can be done in process context of ALSA PCM application as well as software IRQ context for OHCI 1394. Below is an example of the callgraph (some calls are omitted). ioctl(2) with e.g. HWSYNC (sound/core/pcm_native.c) ->snd_pcm_common_ioctl1() ->snd_pcm_hwsync() ->snd_pcm_stream_lock_irq (sound/core/pcm_lib.c) ->snd_pcm_update_hw_ptr() ->snd_pcm_udpate_hw_ptr0() ->struct snd_pcm_ops.pointer() (sound/firewire/*) = Each handler on drivers in ALSA firewire stack (sound/firewire/amdtp-stream.c) ->amdtp_stream_pcm_pointer() (drivers/firewire/core-iso.c) ->fw_iso_context_flush_completions() ->struct fw_card_driver.flush_iso_completion() (drivers/firewire/ohci.c) = flush_iso_completions() ->struct fw_iso_context.callback.sc (sound/firewire/amdtp-stream.c) = in_stream_callback() or out_stream_callback() ->... ->snd_pcm_stream_unlock_irq When packet queueing error occurs or detecting invalid packets in 'in_stream_callback()' or 'out_stream_callback()', 'snd_pcm_stop_xrun()' is called on local CPU with disabled IRQ. (sound/firewire/amdtp-stream.c) in_stream_callback() or out_stream_callback() ->amdtp_stream_pcm_abort() ->snd_pcm_stop_xrun() ->snd_pcm_stream_lock_irqsave() ->snd_pcm_stop() ->snd_pcm_stream_unlock_irqrestore() The process is stalled on the CPU due to attempt to acquire recursive lock. [ 562.630853] INFO: rcu_sched detected stalls on CPUs/tasks: [ 562.630861] 2-...: (1 GPs behind) idle=37d/140000000000000/0 softirq=38323/38323 fqs=7140 [ 562.630862] (detected by 3, t=15002 jiffies, g=21036, c=21035, q=5933) [ 562.630866] Task dump for CPU 2: [ 562.630867] alsa-source-OXF R running task 0 6619 1 0x00000008 [ 562.630870] Call Trace: [ 562.630876] ? vt_console_print+0x79/0x3e0 [ 562.630880] ? msg_print_text+0x9d/0x100 [ 562.630883] ? up+0x32/0x50 [ 562.630885] ? irq_work_queue+0x8d/0xa0 [ 562.630886] ? console_unlock+0x2b6/0x4b0 [ 562.630888] ? vprintk_emit+0x312/0x4a0 [ 562.630892] ? dev_vprintk_emit+0xbf/0x230 [ 562.630895] ? do_sys_poll+0x37a/0x550 [ 562.630897] ? dev_printk_emit+0x4e/0x70 [ 562.630900] ? __dev_printk+0x3c/0x80 [ 562.630903] ? _raw_spin_lock+0x20/0x30 [ 562.630909] ? snd_pcm_stream_lock+0x31/0x50 [snd_pcm] [ 562.630914] ? _snd_pcm_stream_lock_irqsave+0x2e/0x40 [snd_pcm] [ 562.630918] ? snd_pcm_stop_xrun+0x16/0x70 [snd_pcm] [ 562.630922] ? in_stream_callback+0x3e6/0x450 [snd_firewire_lib] [ 562.630925] ? handle_ir_packet_per_buffer+0x8e/0x1a0 [firewire_ohci] [ 562.630928] ? ohci_flush_iso_completions+0xa3/0x130 [firewire_ohci] [ 562.630932] ? fw_iso_context_flush_completions+0x15/0x20 [firewire_core] [ 562.630935] ? amdtp_stream_pcm_pointer+0x2d/0x40 [snd_firewire_lib] [ 562.630938] ? pcm_capture_pointer+0x19/0x20 [snd_oxfw] [ 562.630943] ? snd_pcm_update_hw_ptr0+0x47/0x3d0 [snd_pcm] [ 562.630945] ? poll_select_copy_remaining+0x150/0x150 [ 562.630947] ? poll_select_copy_remaining+0x150/0x150 [ 562.630952] ? snd_pcm_update_hw_ptr+0x10/0x20 [snd_pcm] [ 562.630956] ? snd_pcm_hwsync+0x45/0xb0 [snd_pcm] [ 562.630960] ? snd_pcm_common_ioctl1+0x1ff/0xc90 [snd_pcm] [ 562.630962] ? futex_wake+0x90/0x170 [ 562.630966] ? snd_pcm_capture_ioctl1+0x136/0x260 [snd_pcm] [ 562.630970] ? snd_pcm_capture_ioctl+0x27/0x40 [snd_pcm] [ 562.630972] ? do_vfs_ioctl+0xa3/0x610 [ 562.630974] ? vfs_read+0x11b/0x130 [ 562.630976] ? SyS_ioctl+0x79/0x90 [ 562.630978] ? entry_SYSCALL_64_fastpath+0x1e/0xad This commit fixes the above bug. This assumes two cases: 1. Any error is detected in software IRQ context of OHCI 1394 context. In this case, PCM substream should be aborted in packet handler. On the other hand, it should not be done in any process context. TO distinguish these two context, use 'in_interrupt()' macro. 2. Any error is detect in process context of ALSA PCM application. In this case, PCM substream should not be aborted in packet handler because PCM substream lock is acquired. The task to abort PCM substream should be done in ALSA PCM core. For this purpose, SNDRV_PCM_POS_XRUN is returned at 'struct snd_pcm_ops.pointer()'. Suggested-by:
Clemens Ladisch <clemens@ladisch.de> Fixes: e9148ddd("ALSA: firewire-lib: flush completed packets when reading PCM position") Signed-off-by:
Takashi Sakamoto <o-takashi@sakamocchi.jp> Signed-off-by:
-
Jan Beulich authored
commit 089bc014 upstream. Rather than constructing a local structure instance on the stack, fill the fields directly on the shared ring, just like other backends do. Build on the fact that all response structure flavors are actually identical (the old code did make this assumption too). This is XSA-216. Signed-off-by:
Jan Beulich <jbeulich@suse.com> Reviewed-by:
Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by:
-
Juergen Gross authored
commit 46464411 upstream. Today disconnecting xen-blkback is broken in case there are still I/Os in flight: xen_blkif_disconnect() will bail out early without releasing all resources in the hope it will be called again when the last request has terminated. This, however, won't happen as xen_blkif_free() won't be called on termination of the last running request: xen_blkif_put() won't decrement the blkif refcnt to 0 as xen_blkif_disconnect() didn't finish before thus some xen_blkif_put() calls in xen_blkif_disconnect() didn't happen. To solve this deadlock xen_blkif_disconnect() and xen_blkif_alloc_rings() shouldn't use xen_blkif_put() and xen_blkif_get() but use some other way to do their accounting of resources. This at once fixes another error in xen_blkif_disconnect(): when it returned early with -EBUSY for another ring than 0 it would call xen_blkif_put() again for already handled rings on a subsequent call. This will lead to inconsistencies in the refcnt handling. Signed-off-by:
Juergen Gross <jgross@suse.com> Tested-by:
Steven Haigh <netwiz@crc.id.au> Acked-by:
Roger Pau Monné <roger.pau@citrix.com> Signed-off-by:
-
Chen-Yu Tsai authored
commit 38b8f823 upstream. The register offset for the lcd1-ch1 clock was incorrectly pointing to the lcd0-ch1 clock. This resulted in the lcd0-ch1 clock being disabled when the clk core disables unused clocks. This then stops the simplefb HDMI output path. Reported-by:
Bob Ham <rah@settrans.net> Fixes: c6e6c96d ("clk: sunxi-ng: Add A31/A31s clocks") Signed-off-by:
Chen-Yu Tsai <wens@csie.org> Signed-off-by:
Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by:
-
- 24 Jun, 2017 11 commits
-
-
Greg Kroah-Hartman authored
-
Hugh Dickins authored
commit f4cb767d upstream. Trinity gets kernel BUG at mm/mmap.c:1963! in about 3 minutes of mmap testing. That's the VM_BUG_ON(gap_end < gap_start) at the end of unmapped_area_topdown(). Linus points out how MAP_FIXED (which does not have to respect our stack guard gap intentions) could result in gap_end below gap_start there. Fix that, and the similar case in its alternative, unmapped_area(). Fixes: 1be7107f ("mm: larger stack guard gap, between vmas") Reported-by:
Dave Jones <davej@codemonkey.org.uk> Debugged-by:
Hugh Dickins <hughd@google.com> Acked-by:
-
Helge Deller authored
commit bd726c90 upstream. Fix expand_upwards() on architectures with an upward-growing stack (parisc, metag and partly IA-64) to allow the stack to reliably grow exactly up to the address space limit given by TASK_SIZE. Signed-off-by:
Helge Deller <deller@gmx.de> Acked-by:
-
Hugh Dickins authored
commit 1be7107f upstream. Stack guard page is a useful feature to reduce a risk of stack smashing into a different mapping. We have been using a single page gap which is sufficient to prevent having stack adjacent to a different mapping. But this seems to be insufficient in the light of the stack usage in userspace. E.g. glibc uses as large as 64kB alloca() in many commonly used functions. Others use constructs liks gid_t buffer[NGROUPS_MAX] which is 256kB or stack strings with MAX_ARG_STRLEN. This will become especially dangerous for suid binaries and the default no limit for the stack size limit because those applications can be tricked to consume a large portion of the stack and a single glibc call could jump over the guard page. These attacks are not theoretical, unfortunatelly. Make those attacks less probable by increasing the stack guard gap to 1MB (on systems with 4k pages; but make it depend on the page size because systems with larger base pages might cap stack allocations in the PAGE_SIZE units) which should cover larger alloca() and VLA stack allocations. It is obviously not a full fix because the problem is somehow inherent, but it should reduce attack space a lot. One could argue that the gap size should be configurable from userspace, but that can be done later when somebody finds that the new 1MB is wrong for some special case applications. For now, add a kernel command line option (stack_guard_gap) to specify the stack gap size (in page units). Implementation wise, first delete all the old code for stack guard page: because although we could get away with accounting one extra page in a stack vma, accounting a larger gap can break userspace - case in point, a program run with "ulimit -S -v 20000" failed when the 1MB gap was counted for RLIMIT_AS; similar problems could come with RLIMIT_MLOCK and strict non-overcommit mode. Instead of keeping gap inside the stack vma, maintain the stack guard gap as a gap between vmas: using vm_start_gap() in place of vm_start (or vm_end_gap() in place of vm_end if VM_GROWSUP) in just those few places which need to respect the gap - mainly arch_get_unmapped_area(), and and the vma tree's subtree_gap support for that. Original-patch-by:
Oleg Nesterov <oleg@redhat.com> Original-patch-by:
Willy Tarreau <w@1wt.eu> Signed-off-by:
-
Thomas Gleixner authored
commit ff86bf0c upstream. The alarmtimer code has another source of potentially rearming itself too fast. Interval timers with a very samll interval have a similar CPU hog effect as the previously fixed overflow issue. The reason is that alarmtimers do not implement the normal protection against this kind of problem which the other posix timer use: timer expires -> queue signal -> deliver signal -> rearm timer This scheme brings the rearming under scheduler control and prevents permanently firing timers which hog the CPU. Bringing this scheme to the alarm timer code is a major overhaul because it lacks all the necessary mechanisms completely. So for a quick fix limit the interval to one jiffie. This is not problematic in practice as alarmtimers are usually backed by an RTC for suspend which have 1 second resolution. It could be therefor argued that the resolution of this clock should be set to 1 second in general, but that's outside the scope of this fix. Signed-off-by:
-
David Miller authored
commit d41519a6 upstream. On sparc, if we have an alloca() like situation, as is the case with SHASH_DESC_ON_STACK(), we can end up referencing deallocated stack memory. The result can be that the value is clobbered if a trap or interrupt arrives at just the right instruction. It only occurs if the function ends returning a value from that alloca() area and that value can be placed into the return value register using a single instruction. For example, in lib/libcrc32c.c:crc32c() we end up with a return sequence like: return %i7+8 lduw [%o5+16], %o0 ! MEM[(u32 *)__shash_desc.1_10 + 16B], %o5 holds the base of the on-stack area allocated for the shash descriptor. But the return released the stack frame and the register window. So if an intererupt arrives between 'return' and 'lduw', then the value read at %o5+16 can be corrupted. Add a data compiler barrier to work around this problem. This is exactly what the gcc fix will end up doing as well, and it absolutely should not change the code generated for other cpus (unless gcc on them has the same bug :-) With crucial insight from Eric Sandeen. Reported-by:
Anatoly Pugachev <matorola@gmail.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Hon Ching \(Vicky) Lo authored
commit 31574d32 upstream. The current code passes the address of tpm_chip as the argument to dev_get_drvdata() without prior NULL check in tpm_ibmvtpm_get_desired_dma. This resulted an oops during kernel boot when vTPM is enabled in Power partition configured in active memory sharing mode. The vio_driver's get_desired_dma() is called before the probe(), which for vtpm is tpm_ibmvtpm_probe, and it's this latter function that initializes the driver and set data. Attempting to get data before the probe() caused the problem. This patch adds a NULL check to the tpm_ibmvtpm_get_desired_dma. fixes: 9e0d39d8 ("tpm: Remove useless priv field in struct tpm_vendor_specific") Signed-off-by:
Hon Ching(Vicky) Lo <honclo@linux.vnet.ibm.com> Reviewed-by:
Jarkko Sakkine <jarkko.sakkinen@linux.intel.com> Signed-off-by:
-
Paul Burton authored
commit bcd7c45e upstream. The .its targets require information about the kernel binary, such as its entry point, which is extracted from the vmlinux ELF. We therefore require that the ELF is built before the .its files are generated. Declare this requirement in the Makefile such that make will ensure this is always the case, otherwise in corner cases we can hit issues as the .its is generated with an incorrect (either invalid or stale) entry point. Signed-off-by:
Paul Burton <paul.burton@imgtec.com> Fixes: cf2a5e0b ("MIPS: Support generating Flattened Image Trees (.itb)") Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/16179/Signed-off-by:
Ralf Baechle <ralf@linux-mips.org> Signed-off-by:
-
Paul Burton authored
commit 1a73d931 upstream. The code handling the pop76 opcode (ie. bnezc & jialc instructions) in __compute_return_epc_for_insn() needs to set the value of $31 in the jialc case, which is encoded with rs = 0. However its check to differentiate bnezc (rs != 0) from jialc (rs = 0) was unfortunately backwards, meaning that if we emulate a bnezc instruction we clobber $31 & if we emulate a jialc instruction it actually behaves like a jic instruction. Fix this by inverting the check of rs to match the way the instructions are actually encoded. Signed-off-by:
-
Shuah Khan authored
commit 8ae584d1 upstream. Axius clock error path returns without disabling clock and suspend clock. Fix it to disable them before returning error. Reviewed-by:
Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by:
Shuah Khan <shuahkh@osg.samsung.com> Signed-off-by:
Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by:
Sasha Levin <alexander.levin@verizon.com> Signed-off-by:
-
Christophe JAILLET authored
commit 990758c5 upstream. 'cdev->os_desc_req' has been allocated with 'usb_ep_alloc_request()' so 'usb_ep_free_request()' should be used to free it. Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by:
-
