Simplify this part of code. No logic changes.

Link: https://lore.kernel.org/r/20220529055425.226363-3-xiang@kernel.orgAcked-by: Chao Yu <chao@kernel.org>
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>

It was incompletely introduced for deduplication between different
logical extents backed with the same pcluster.

We will have a better in-memory representation in the next release
cycle for this, as well as partial memory folios support. So get rid
of it instead.

No logic changes.

Link: https://lore.kernel.org/r/20220529055425.226363-2-xiang@kernel.orgAcked-by: Chao Yu <chao@kernel.org>
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>

 - refine the filesystem overview for better description of recent
   new features like FSDAX and Fscache;

 - add the new `fsid' mount option;

 - fix some typos.

Link: https://lore.kernel.org/r/20220527070133.77962-1-hsiangkao@linux.alibaba.comReviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>

RIP: 0010:trace_event_raw_event_cachefiles_prep_read+0x88/0xe0
[cachefiles]
Call Trace:
  <TASK>
  cachefiles_prepare_read+0x1d7/0x3a0 [cachefiles]
  erofs_fscache_read_folios+0x188/0x220 [erofs]
  erofs_fscache_meta_readpage+0x106/0x160 [erofs]
  do_read_cache_folio+0x42a/0x590
  ? bdi_register_va.part.14+0x1a7/0x210
  ? super_setup_bdi_name+0x76/0xe0
  erofs_bread+0x5b/0x170 [erofs]
  erofs_fc_fill_super+0x12b/0xc50 [erofs]

This tracepoint uses rreq->inode, should set it when allocating.

Fixes: d435d532 ("erofs: change to use asynchronous io for fscache readpage/readahead")
Signed-off-by: Xin Yin <yinxin.x@bytedance.com>
Reviewed-by: Jeffle Xu <jefflexu@linux.alibaba.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Link: https://lore.kernel.org/r/20220527101800.22360-1-yinxin.x@bytedance.comSigned-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>

erofs over fscache doesn't support the compressed layout yet. It will
cause NULL crash if there are compressed inodes contained when working
in fscache mode.

So far in the erofs based container image distribution scenarios
(RAFS v6), the compressed RAFS v6 images are downloaded and then
decompressed on demand as an uncompressed erofs image. Then the erofs
image is mounted in fscache mode for containers to use. IOWs, currently
compressed data is decompressed on the userspace side instead and
uncompressed erofs images will be finally cached.

The fscache support for the compressed layout is still under
development and it will be used for runtime decompression feature.
Anyway, to avoid the potential crash, let's leave the compressed inodes
unsupported in fscache mode until we support it later.

Fixes: 1442b02b ("erofs: implement fscache-based data read for non-inline layout")
Signed-off-by: Jeffle Xu <jefflexu@linux.alibaba.com>
Reviewed-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Link: https://lore.kernel.org/r/20220526010344.118493-1-jefflexu@linux.alibaba.comSigned-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>

Pull erofs (and fscache) updates from Gao Xiang:
 "After working on it on the mailing list for more than half a year, we
  finally form 'erofs over fscache' feature into shape. Hopefully it
  could bring more possibility to the communities.

  The story mainly started from a new project what we called "RAFS v6" [1]
  for Nydus image service almost a year ago, which enhances EROFS to be
  a new form of one bootstrap (which includes metadata representing the
  whole fs tree) + several data-deduplicated content addressable blobs
  (actually treated as multiple devices). Each blob can represent one
  container image layer but not quite exactly since all new data can be
  fully existed in the previous blobs so no need to introduce another
  new blob.

  It is actually not a new idea (at least on my side it's much like a
  simpilied casync [2] for now) and has many benefits over per-file
  blobs or some other exist ways since typically each RAFS v6 image only
  has dozens of device blobs instead of thousands of per-file blobs.
  It's easy to be signed with user keys as a golden image, transfered
  untouchedly with minimal overhead over the network, kept in some type
  of storage conveniently, and run with (optional) runtime verification
  but without involving too many irrelevant features crossing the system
  beyond EROFS itself. At least it's our final goal and we're keeping
  working on it. There was also a good summary of this approach from the
  casync author [3].

  Regardless further optimizations, this work is almost done in the
  previous Linux release cycles. In this round, we'd like to introduce
  on-demand load for EROFS with the fscache/cachefiles infrastructure,
  considering the following advantages:

   - Introduce new file-based backend to EROFS. Although each image only
     contains dozens of blobs but in densely-deployed runC host for
     example, there could still be massive blobs on a machine, which is
     messy if each blob is treated as a device. In contrast, fscache and
     cachefiles are really great interfaces for us to make them work.

   - Introduce on-demand load to fscache and EROFS. Previously, fscache
     is mainly used to caching network-likewise filesystems, now it can
     support on-demand downloading for local fses too with the exact
     localfs on-disk format. It has many advantages which we're been
     described in the latest patchset cover letter [4]. In addition to
     that, most importantly, the cached data is still stored in the
     original local fs on-disk format so that it's still the one signed
     with private keys but only could be partially available. Users can
     fully trust it during running. Later, users can also back up
     cachefiles easily to another machine.

   - More reliable on-demand approach in principle. After data is all
     available locally, user daemon can be no longer online in some use
     cases, which helps daemon crash recovery (filesystems can still in
     service) and hot-upgrade (user daemon can be upgraded more
     frequently due to new features or protocols introduced.)

   - Other format can also be converted to EROFS filesystem format over
     the internet on the fly with the new on-demand load feature and
     mounted. That is entirely possible with on-demand load feature as
     long as such archive format metadata can be fetched in advance like
     stargz.

  In addition, although currently our target user is Nydus image service [5],
  but laterly, it can be used for other use cases like on-demand system
  booting, etc. As for the fscache on-demand load feature itself,
  strictly it can be used for other local fses too. Laterly we could
  promote most code to the iomap infrastructure and also enhance it in
  the read-write way if other local fses are interested.

  Thanks David Howells for taking so much time and patience on this
  these months, many thanks with great respect here again! Thanks Jeffle
  for working on this feature and Xin Yin from Bytedance for
  asynchronous I/O implementation as well as Zichen Tian, Jia Zhu, and
  Yan Song for testing, much appeciated. We're also exploring more
  possibly over fscache cache management over FSDAX for secure
  containers and working on more improvements and useful features for
  fscache, cachefiles, and on-demand load.

  In addition to "erofs over fscache", NFS export and idmapped mount are
  also completed in this cycle for container use cases as well.

  Summary:

   - Add erofs on-demand load support over fscache

   - Support NFS export for erofs

   - Support idmapped mounts for erofs

   - Don't prompt for risk any more when using big pcluster

   - Fix buffer copy overflow of ztailpacking feature

   - Several minor cleanups"

[1] https://lore.kernel.org/r/20210730194625.93856-1-hsiangkao@linux.alibaba.com
[2] https://github.com/systemd/casync
[3] http://0pointer.net/blog/casync-a-tool-for-distributing-file-system-images.html
[4] https://lore.kernel.org/r/20220509074028.74954-1-jefflexu@linux.alibaba.com
[5] https://github.com/dragonflyoss/image-service

* tag 'erofs-for-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs: (29 commits)
  erofs: scan devices from device table
  erofs: change to use asynchronous io for fscache readpage/readahead
  erofs: add 'fsid' mount option
  erofs: implement fscache-based data readahead
  erofs: implement fscache-based data read for inline layout
  erofs: implement fscache-based data read for non-inline layout
  erofs: implement fscache-based metadata read
  erofs: register fscache context for extra data blobs
  erofs: register fscache context for primary data blob
  erofs: add erofs_fscache_read_folios() helper
  erofs: add anonymous inode caching metadata for data blobs
  erofs: add fscache context helper functions
  erofs: register fscache volume
  erofs: add fscache mode check helper
  erofs: make erofs_map_blocks() generally available
  cachefiles: document on-demand read mode
  cachefiles: add tracepoints for on-demand read mode
  cachefiles: enable on-demand read mode
  cachefiles: implement on-demand read
  cachefiles: notify the user daemon when withdrawing cookie
  ...

Pull exfat updates from Namjae Jeon:

 - fix referencing wrong parent directory information during rename

 - introduce a sys_tz mount option to use system timezone

 - improve performance while zeroing a cluster with dirsync mount option

 - fix slab-out-bounds in exat_clear_bitmap() reported from syzbot

* tag 'exfat-for-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/linkinjeon/exfat:
  exfat: check if cluster num is valid
  exfat: reduce block requests when zeroing a cluster
  block: add sync_blockdev_range()
  exfat: introduce mount option 'sys_tz'
  exfat: fix referencing wrong parent directory information after renaming

Pull fs idmapping updates from Christian Brauner:
 "This contains two minor updates:

   - An update to the idmapping documentation by Rodrigo making it
     easier to understand that we first introduce several use-cases that
     fail without idmapped mounts simply to explain how they can be
     handled with idmapped mounts.

   - When changing a mount's idmapping we now hold writers to make it
     more robust.

     This is similar to turning a mount ro with the difference that in
     contrast to turning a mount ro changing the idmapping can only ever
     be done once while a mount can transition between ro and rw as much
     as it wants.

     The vfs layer itself takes care to retrieve the idmapping of a
     mount once ensuring that the idmapping used for vfs permission
     checking is identical to the idmapping passed down to the
     filesystem. All filesystems with FS_ALLOW_IDMAP raised take the
     same precautions as the vfs in code-paths that are outside of
     direct control of the vfs such as ioctl()s.

     However, holding writers makes this more robust and predictable for
     both the kernel and userspace.

     This is a minor user-visible change. But it is extremely unlikely
     to matter. The caller must've created a detached mount via
     OPEN_TREE_CLONE and then handed that O_PATH fd to another process
     or thread which then must've gotten a writable fd for that mount
     and started creating files in there while the caller is still
     changing mount properties. While not impossible it will be an
     extremely rare corner-case and should in general be considered a
     bug in the application. Consider making a mount MOUNT_ATTR_NOEXEC
     or MOUNT_ATTR_NODEV while allowing someone else to perform lookups
     or exec'ing in parallel by handing them a copy of the
     OPEN_TREE_CLONE fd or another fd beneath that mount.

     I've pinged all major users of idmapped mounts pointing out this
     change and none of them have active writers on a mount while still
     changing mount properties. It would've been strange if they did.

  The rest and majority of the work will be coming through the overlayfs
  tree this cycle. In addition to overlayfs this cycle should also see
  support for idmapped mounts on erofs as I've acked a patch to this
  effect a little while ago"

* tag 'fs.idmapped.v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux:
  fs: hold writers when changing mount's idmapping
  docs: Add small intro to idmap examples

Pull media updates from Mauro Carvalho Chehab:

 - dvb-usb drivers entries got reworked to avoid usage of magic numbers
   to refer to data position inside tables

 - vcodec driver has gained support for MT8186 and for vp8 and vp9
   stateless codecs

 - hantro has gained support for Hantro G1 on RK366x

 - Added more h264 levels on coda960

 - ccs gained support for MIPI CSI-2 28 bits per pixel raw data type

 - venus driver gained support for Qualcomm custom compressed pixel
   formats

 - lots of driver fixes and updates

* tag 'media/v5.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (308 commits)
  media: hantro: Enable HOLD_CAPTURE_BUF for H.264
  media: hantro: Add H.264 field decoding support
  media: hantro: h264: Make dpb entry management more robust
  media: hantro: Stop using H.264 parameter pic_num
  media: rkvdec: Enable capture buffer holding for H264
  media: rkvdec-h264: Add field decoding support
  media: rkvdec: Ensure decoded resolution fit coded resolution
  media: rkvdec: h264: Fix reference frame_num wrap for second field
  media: rkvdec: h264: Validate and use pic width and height in mbs
  media: rkvdec: Move H264 SPS validation in rkvdec-h264
  media: rkvdec: h264: Fix bit depth wrap in pps packet
  media: rkvdec: h264: Fix dpb_valid implementation
  media: rkvdec: Stop overclocking the decoder
  media: v4l2: Reorder field reflist
  media: h264: Sort p/b reflist using frame_num
  media: v4l2: Trace calculated p/b0/b1 initial reflist
  media: h264: Store all fields into the unordered list
  media: h264: Store current picture fields
  media: h264: Increase reference lists size to 32
  media: h264: Use v4l2_h264_reference for reflist
  ...

Pull device properties framework updates from Rafael Wysocki:
 "These mostly extend the device property API and make it easier to use
  in some cases.

  Specifics:

   - Allow error pointer to be passed to fwnode APIs (Andy Shevchenko).

   - Introduce fwnode_for_each_parent_node() (Andy Shevchenko, Douglas
     Anderson).

   - Advertise fwnode and device property count API calls (Andy
     Shevchenko).

   - Clean up fwnode_is_ancestor_of() (Andy Shevchenko).

   - Convert device_{dma_supported,get_dma_attr} to fwnode (Sakari
     Ailus).

   - Release subnode properties with data nodes (Sakari Ailus).

   - Add ->iomap() and ->irq_get() to fwnode operations (Sakari Ailus)"

* tag 'devprop-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  device property: Advertise fwnode and device property count API calls
  device property: Fix recent breakage of fwnode_get_next_parent_dev()
  device property: Drop 'test' prefix in parameters of fwnode_is_ancestor_of()
  device property: Introduce fwnode_for_each_parent_node()
  device property: Allow error pointer to be passed to fwnode APIs
  ACPI: property: Release subnode properties with data nodes
  device property: Add irq_get to fwnode operation
  device property: Add iomap to fwnode operations
  ACPI: property: Move acpi_fwnode_device_get_match_data() up
  device property: Convert device_{dma_supported,get_dma_attr} to fwnode

Pull thermal control updates from Rafael Wysocki:
 "These add a thermal library and thermal tools to wrap the netlink
  interface into event-based callbacks, improve overheat condition
  handling during suspend-to-idle on Intel SoCs, add some new hardware
  support, fix bugs and clean up code.

  Specifics:

   - Add thermal library and thermal tools to encapsulate the netlink
     into event based callbacks (Daniel Lezcano, Jiapeng Chong).

   - Improve overheat condition handling during suspend-to-idle in the
     Intel PCH thermal driver (Zhang Rui).

   - Use local ops instead of global ops in devfreq_cooling (Kant Fan).

   - Clean up _OSC handling in int340x (Davidlohr Bueso).

   - Switch hisi_termal from CONFIG_PM_SLEEP guards to pm_sleep_ptr()
     (Hesham Almatary).

   - Add new k3 j72xx bangdap driver and the corresponding bindings
     (Keerthy).

   - Fix missing of_node_put() in the SC iMX driver at probe time
     (Miaoqian Lin).

   - Fix memory leak in __thermal_cooling_device_register()
     when device_register() fails by calling
     thermal_cooling_device_destroy_sysfs() (Yang Yingliang).

   - Add sc8180x and sc8280xp compatible string in the DT bindings and
     lMH support for QCom tsens driver (Bjorn Andersson).

   - Fix OTP Calibration Register values conforming to the documentation
     on RZ/G2L and bindings documentation for RZ/G2UL (Biju Das).

   - Fix type in kerneldoc description for __thermal_bind_params
     (Corentin Labbe).

   - Fix potential NULL dereference in sr_thermal_probe() on Broadcom
     platform (Zheng Yongjun).

   - Add change mode ops to the thermal-of sensor (Manaf Meethalavalappu
     Pallikunhi).

   - Fix non-negative value support by preventing the value to be clamp
     to zero (Stefan Wahren).

   - Add compatible string and DT bindings for MSM8960 tsens driver
     (Dmitry Baryshkov).

   - Add hwmon support for K3 driver (Massimiliano Minella).

   - Refactor and add multiple generations support for QCom ADC driver
     (Jishnu Prakash).

   - Use platform_get_irq_optional() to get the interrupt on RCar driver
     and document Document RZ/V2L bindings (Lad Prabhakar).

   - Remove NULL check after container_of() call from the Intel HFI
     thermal driver (Haowen Bai)"

* tag 'thermal-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (38 commits)
  thermal: intel: pch: improve the cooling delay log
  thermal: intel: pch: enhance overheat handling
  thermal: intel: pch: move cooling delay to suspend_noirq phase
  PM: wakeup: expose pm_wakeup_pending to modules
  thermal: k3_j72xx_bandgap: Add the bandgap driver support
  dt-bindings: thermal: k3-j72xx: Add VTM bindings documentation
  thermal/drivers/imx_sc_thermal: Fix refcount leak in imx_sc_thermal_probe
  thermal/core: Fix memory leak in __thermal_cooling_device_register()
  dt-bindings: thermal: tsens: Add sc8280xp compatible
  dt-bindings: thermal: lmh: Add Qualcomm sc8180x compatible
  thermal/drivers/qcom/lmh: Add sc8180x compatible
  thermal/drivers/rz2gl: Fix OTP Calibration Register values
  dt-bindings: thermal: rzg2l-thermal: Document RZ/G2UL bindings
  thermal: thermal_of: fix typo on __thermal_bind_params
  tools/thermal: remove unneeded semicolon
  tools/lib/thermal: remove unneeded semicolon
  thermal/drivers/broadcom: Fix potential NULL dereference in sr_thermal_probe
  tools/thermal: Add thermal daemon skeleton
  tools/thermal: Add a temperature capture tool
  tools/thermal: Add util library
  ...

Pull power management updates from Rafael Wysocki:
 "These add support for 'artificial' Energy Models in which power
  numbers for different entities may be in different scales, add support
  for some new hardware, fix bugs and clean up code in multiple places.

  Specifics:

   - Update the Energy Model support code to allow the Energy Model to
     be artificial, which means that the power values may not be on a
     uniform scale with other devices providing power information, and
     update the cpufreq_cooling and devfreq_cooling thermal drivers to
     support artificial Energy Models (Lukasz Luba).

   - Make DTPM check the Energy Model type (Lukasz Luba).

   - Fix policy counter decrementation in cpufreq if Energy Model is in
     use (Pierre Gondois).

   - Add CPU-based scaling support to passive devfreq governor (Saravana
     Kannan, Chanwoo Choi).

   - Update the rk3399_dmc devfreq driver (Brian Norris).

   - Export dev_pm_ops instead of suspend() and resume() in the IIO
     chemical scd30 driver (Jonathan Cameron).

   - Add namespace variants of EXPORT[_GPL]_SIMPLE_DEV_PM_OPS and
     PM-runtime counterparts (Jonathan Cameron).

   - Move symbol exports in the IIO chemical scd30 driver into the
     IIO_SCD30 namespace (Jonathan Cameron).

   - Avoid device PM-runtime usage count underflows (Rafael Wysocki).

   - Allow dynamic debug to control printing of PM messages (David
     Cohen).

   - Fix some kernel-doc comments in hibernation code (Yang Li, Haowen
     Bai).

   - Preserve ACPI-table override during hibernation (Amadeusz
     Sławiński).

   - Improve support for suspend-to-RAM for PSCI OSI mode (Ulf Hansson).

   - Make Intel RAPL power capping driver support the RaptorLake and
     AlderLake N processors (Zhang Rui, Sumeet Pawnikar).

   - Remove redundant store to value after multiply in the RAPL power
     capping driver (Colin Ian King).

   - Add AlderLake processor support to the intel_idle driver (Zhang
     Rui).

   - Fix regression leading to no genpd governor in the PSCI cpuidle
     driver and fix the riscv-sbi cpuidle driver to allow a genpd
     governor to be used (Ulf Hansson).

   - Fix cpufreq governor clean up code to avoid using kfree() directly
     to free kobject-based items (Kevin Hao).

   - Prepare cpufreq for powerpc's asm/prom.h cleanup (Christophe
     Leroy).

   - Make intel_pstate notify frequency invariance code when no_turbo is
     turned on and off (Chen Yu).

   - Add Sapphire Rapids OOB mode support to intel_pstate (Srinivas
     Pandruvada).

   - Make cpufreq avoid unnecessary frequency updates due to mismatch
     between hardware and the frequency table (Viresh Kumar).

   - Make remove_cpu_dev_symlink() clear the real_cpus mask to simplify
     code (Viresh Kumar).

   - Rearrange cpufreq_offline() and cpufreq_remove_dev() to make the
     calling convention for some driver callbacks consistent (Rafael
     Wysocki).

   - Avoid accessing half-initialized cpufreq policies from the show()
     and store() sysfs functions (Schspa Shi).

   - Rearrange cpufreq_offline() to make the calling convention for some
     driver callbacks consistent (Schspa Shi).

   - Update CPPC handling in cpufreq (Pierre Gondois).

   - Extend dev_pm_domain_detach() doc (Krzysztof Kozlowski).

   - Move genpd's time-accounting to ktime_get_mono_fast_ns() (Ulf
     Hansson).

   - Improve the way genpd deals with its governors (Ulf Hansson).

   - Update the turbostat utility to version 2022.04.16 (Len Brown, Dan
     Merillat, Sumeet Pawnikar, Zephaniah E. Loss-Cutler-Hull, Chen Yu)"

* tag 'pm-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (94 commits)
  PM: domains: Trust domain-idle-states from DT to be correct by genpd
  PM: domains: Measure power-on/off latencies in genpd based on a governor
  PM: domains: Allocate governor data dynamically based on a genpd governor
  PM: domains: Clean up some code in pm_genpd_init() and genpd_remove()
  PM: domains: Fix initialization of genpd's next_wakeup
  PM: domains: Fixup QoS latency measurements for IRQ safe devices in genpd
  PM: domains: Measure suspend/resume latencies in genpd based on governor
  PM: domains: Move the next_wakeup variable into the struct gpd_timing_data
  PM: domains: Allocate gpd_timing_data dynamically based on governor
  PM: domains: Skip another warning in irq_safe_dev_in_sleep_domain()
  PM: domains: Rename irq_safe_dev_in_no_sleep_domain() in genpd
  PM: domains: Don't check PM_QOS_FLAG_NO_POWER_OFF in genpd
  PM: domains: Drop redundant code for genpd always-on governor
  PM: domains: Add GENPD_FLAG_RPM_ALWAYS_ON for the always-on governor
  powercap: intel_rapl: remove redundant store to value after multiply
  cpufreq: CPPC: Enable dvfs_possible_from_any_cpu
  cpufreq: CPPC: Enable fast_switch
  ACPI: CPPC: Assume no transition latency if no PCCT
  ACPI: bus: Set CPPC _OSC bits for all and when CPPC_LIB is supported
  ACPI: CPPC: Check _OSC for flexible address space
  ...

Pull ACPI updates from Rafael Wysocki:
 "These update the ACPICA kernel code to upstream revision 20220331,
  improve handling of PCI devices that are in D3cold during system
  initialization, add support for a few features, fix bugs and clean up
  code.

  Specifics:

   - Update ACPICA code in the kernel to upstream revision 20220331
     including the following changes:
       - Add support for the Windows 11 _OSI string (Mario Limonciello)
       - Add the CFMWS subtable to the CEDT table (Lawrence Hileman).
       - iASL: NHLT: Treat Terminator as specific_config (Piotr
         Maziarz).
       - iASL: NHLT: Fix parsing undocumented bytes at the end of
         Endpoint Descriptor (Piotr Maziarz).
       - iASL: NHLT: Rename linux specific strucures to device_info
         (Piotr Maziarz).
       - Add new ACPI 6.4 semantics to Load() and LoadTable() (Bob
         Moore).
       - Clean up double word in comment (Tom Rix).
       - Update copyright notices to the year 2022 (Bob Moore).
       - Remove some tabs and // comments - automated cleanup (Bob
         Moore).
       - Replace zero-length array with flexible-array member (Gustavo
         A. R. Silva).
       - Interpreter: Add units to time variable names (Paul Menzel).
       - Add support for ARM Performance Monitoring Unit Table (Besar
         Wicaksono).
       - Inform users about ACPI spec violation related to sleep length
         (Paul Menzel).
       - iASL/MADT: Add OEM-defined subtable (Bob Moore).
       - Interpreter: Fix some typo mistakes (Selvarasu Ganesan).
       - Updates for revision E.d of IORT (Shameer Kolothum).
       - Use ACPI_FORMAT_UINT64 for 64-bit output (Bob Moore).

   - Improve debug messages in the ACPI device PM code (Rafael Wysocki).

   - Block ASUS B1400CEAE from suspend to idle by default (Mario
     Limonciello).

   - Improve handling of PCI devices that are in D3cold during system
     initialization (Rafael Wysocki).

   - Fix BERT error region memory mapping (Lorenzo Pieralisi).

   - Add support for NVIDIA 16550-compatible port subtype to the SPCR
     parsing code (Jeff Brasen).

   - Use static for BGRT_SHOW kobj_attribute defines (Tom Rix).

   - Fix missing prototype warning for acpi_agdi_init() (Ilkka
     Koskinen).

   - Fix missing ERST record ID in the APEI code (Liu Xinpeng).

   - Make APEI error injection to refuse to inject into the zero page
     (Tony Luck).

   - Correct description of INT3407 / INT3532 DPTF attributes in sysfs
     (Sumeet Pawnikar).

   - Add support for high frequency impedance notification to the DPTF
     driver (Sumeet Pawnikar).

   - Make mp_config_acpi_gsi() a void function (Li kunyu).

   - Unify Package () representation for properties in the ACPI device
     properties documentation (Andy Shevchenko).

   - Include UUID in _DSM evaluation warning (Michael Niewöhner)"

* tag 'acpi-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (41 commits)
  Revert "ACPICA: executer/exsystem: Warn about sleeps greater than 10 ms"
  ACPI: utils: include UUID in _DSM evaluation warning
  ACPI: PM: Block ASUS B1400CEAE from suspend to idle by default
  x86: ACPI: Make mp_config_acpi_gsi() a void function
  ACPI: DPTF: Add support for high frequency impedance notification
  ACPI: AGDI: Fix missing prototype warning for acpi_agdi_init()
  ACPI: bus: Avoid non-ACPI device objects in walks over children
  ACPI: DPTF: Correct description of INT3407 / INT3532 attributes
  ACPI: BGRT: use static for BGRT_SHOW kobj_attribute defines
  ACPI, APEI, EINJ: Refuse to inject into the zero page
  ACPI: PM: Always print final debug message in acpi_device_set_power()
  ACPI: SPCR: Add support for NVIDIA 16550-compatible port subtype
  ACPI: docs: enumeration: Unify Package () for properties (part 2)
  ACPI: APEI: Fix missing ERST record id
  ACPICA: Update version to 20220331
  ACPICA: exsystem.c: Use ACPI_FORMAT_UINT64 for 64-bit output
  ACPICA: IORT: Updates for revision E.d
  ACPICA: executer/exsystem: Fix some typo mistakes
  ACPICA: iASL/MADT: Add OEM-defined subtable
  ACPICA: executer/exsystem: Warn about sleeps greater than 10 ms
  ...

Pull HID updates from Jiri Kosina:

 - support for pens with 3 buttons with Wacom driver (Joshua Dickens)

 - support for HID_DG_SCANTIME to report the timestamp for pen and touch
   events in Wacom driver (Joshua Dickens)

 - support for sensor discovery in amd-sfh driver (Basavaraj Natikar)

 - support for wider variety of Huion tablets ported from DIGImend
   project (José Expósito, Nikolai Kondrashov)

 - new device IDs and other assorted small code cleanups

* tag 'for-linus-2022052401' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid: (44 commits)
  HID: apple: Properly handle function keys on Keychron keyboards
  HID: uclogic: Switch to Digitizer usage for styluses
  HID: uclogic: Add pen support for XP-PEN Star 06
  HID: uclogic: Differentiate touch ring and touch strip
  HID: uclogic: Always shift touch reports to zero
  HID: uclogic: Do not focus on touch ring only
  HID: uclogic: Return raw parameters from v2 pen init
  HID: uclogic: Move param printing to a function
  HID: core: Display "SENSOR HUB" for sensor hub bus string in hid_info
  HID: amd_sfh: Move bus declaration outside of amd-sfh
  HID: amd_sfh: Add physical location to HID device
  HID: amd_sfh: Modify the hid name
  HID: amd_sfh: Modify the bus name
  HID: amd_sfh: Add sensor name by index for debug info
  HID: amd_sfh: Add support for sensor discovery
  HID: bigben: fix slab-out-of-bounds Write in bigben_probe
  Hid: wacom: Fix kernel test robot warning
  HID: uclogic: Disable pen usage for Huion keyboard interfaces
  HID: uclogic: Support disabling pen usage
  HID: uclogic: Pass keyboard reports as is
  ...

Pull spi updates from Mark Brown:
 "This is quite a quiet release but some new drivers mean that the
  diffstat is fairly large. The new drivers include the aspeed driver
  which is migrated from MTD as part of the ongoing move of controllers
  with specialised support for SPI flashes into the SPI subsystem.

   - Support for devices which flip CPHA during recieve only transfers
     (eg, if MOSI and MISO have inverted polarity).

   - Overhaul of the i.MX driver, including the addition of PIO support
     for better performance on small transfers.

   - Migration of the Aspeed driver from MTD.

   - Support for Aspeed AST2400, Ingenic JZ4775 and X1/2000 and MediaTek
     IPM and SFI"

* tag 'spi-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (84 commits)
  spi: spi-au1550: replace ternary operator with min()
  mtd: spi-nor: aspeed: set the decoding size to at least 2MB for AST2600
  spi: aspeed: Calibrate read timings
  spi: aspeed: Add support for the AST2400 SPI controller
  spi: aspeed: Workaround AST2500 limitations
  spi: aspeed: Adjust direct mapping to device size
  spi: aspeed: Add support for direct mapping
  spi: spi-mem: Convert Aspeed SMC driver to spi-mem
  spi: Convert the Aspeed SMC controllers device tree binding
  spi: spi-cadence: Update ISR status variable type to irqreturn_t
  spi: Doc fix - Describe add_lock and dma_map_dev in spi_controller
  spi: cadence-quadspi: Handle spi_unregister_master() in remove()
  spi: stm32-qspi: Remove SR_BUSY bit check before sending command
  spi: stm32-qspi: Always check SR_TCF flags in stm32_qspi_wait_cmd()
  spi: stm32-qspi: Fix wait_cmd timeout in APM mode
  spi: cadence-quadspi: remove unnecessary (void *) casts
  spi: cadence-quadspi: Add missing blank line in cqspi_request_mmap_dma()
  spi: spi-imx: mx51_ecspi_prepare_message(): skip writing MX51_ECSPI_CONFIG register if unchanged
  spi: spi-imx: add PIO polling support
  spi: spi-imx: replace struct spi_imx_data::bitbang by pointer to struct spi_controller
  ...

Pull regulator updates from Mark Brown:
 "This is mostly a drivers update including a couple of new drivers but
  we do have some fixes and improvements to the core as well.

   - Make sure we don't log spuriously about uncontrollable regulators.

   - Don't use delays when we should use sleeps for regulators with
     larger ramp times.

   - Support for MediaTek MT6358 and MT6366, Richtek RT5759 and Silicon
     Mitus SM5703"

* tag 'regulator-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (36 commits)
  regulator: scmi: Fix refcount leak in scmi_regulator_probe
  regulator: pfuze100: Fix refcount leak in pfuze_parse_regulators_dt
  regulator: qcom_smd: Fix up PM8950 regulator configuration
  regulator: core: Fix enable_count imbalance with EXCLUSIVE_GET
  regulator: core: Add error flags to sysfs attributes
  regulator: dt-bindings: qcom,rpmh: document vdd-l7-bob-supply on PMR735A
  regulator: dt-bindings: qcom,rpmh: document supplies per variant
  regulator: dt-bindings: qcom,rpmh: update maintainers
  regulator: mt6315: Enforce regulator-compatible, not name
  regulator: pca9450: Enable DVS control via PMIC_STBY_REQ
  regulator: pca9450: Make warm reset on WDOG_B assertion
  regulator: Add property for WDOG_B warm reset
  regulator: pca9450: Make I2C Level Translator configurable
  regulator: Add property for I2C level shifter
  regulator: sm5703: Correct reference to the common regulator schema
  regulator: sm5703-regulator: Add regulators support for SM5703 MFD
  dt-bindings: regulator: Add bindings for Silicon Mitus SM5703 regulators
  regulator: richtek,rt4801: parse GPIOs per regulator
  regulator: dt-bindings: richtek,rt4801: use existing ena_gpiod feature
  regulator: core: Sleep (not delay) in set_voltage()
  ...

Pull regmap updates from Mark Brown:
 "The main change here is Marek's addition of bulk read/write callbacks
  for individual regmaps, we've supported single register operations for
  a while but there's enough hardware out there which can use bulk
  equivalents to make it worthwhile"

* tag 'regmap-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
  regmap: Add missing map->bus check
  regmap: Add bulk read/write callbacks into regmap_config
  regmap: cache: set max_register with reg_stride
  regmap: Constify static regmap_bus structs

Pull MMC updates from Ulf Hansson:
 "MMC core:

   - Support zero-out using TRIM for eMMC

   - Allow to override the busy-timeout for the ioctl-cmds

  MMC host:

   - Continued the conversion of DT bindings into the JSON schema

   - jz4740: Apply DMA engine limits to maximum segment size

   - mmci_stm32: Use a buffer for unaligned DMA requests

   - mmc_spi: Enabled high-speed modes via parsing of DT

   - omap: Make clock management to be compliant with CCF

   - renesas_sdhi:
      - Support eMMC HS400 mode for R-Car V3H ES2.0
      - Don't allow support for eMMC HS400 for R-Car V3M/D3

   - sdhci_am654: Fix problem when SD card slot lacks the card detect
     line

   - sdhci-esdhc-imx: Add support for the imx8dxl variant

   - sdhci-brcmstb: Enable support for clock gating to save power

   - sdhci-msm:
      - Add support for the sdx65 variant
      - Add support for the sm8150 variant

   - sdhci-of-dwcmshc: Add support for the Rockchip rk3588 variant

   - sdhci-pci-gli: Add workaround to allow GL9755 to enter ASPM L1.2"

* tag 'mmc-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (52 commits)
  mmc: sdhci-of-arasan: Add NULL check for data field
  mmc: core: Support zeroout using TRIM for eMMC
  mmc: sdhci-brcmstb: Fix compiler warning
  mmc: sdhci-msm: Add compatible string check for sdx65
  dt-bindings: mmc: sdhci-msm: Document the SDX65 compatible
  mmc: sdhci-msm: Add compatible string check for sm8150
  dt-bindings: mmc: sdhci-msm: Add compatible string for sm8150
  mmc: sdhci-msm: Add SoC specific compatibles
  dt-bindings: mmc: sdhci-msm: Convert bindings to yaml
  dt-bindings: mmc: brcm,sdhci-brcmstb: cleanup example
  dt-bindings: mmc: brcm,sdhci-brcmstb: correct number of reg entries
  mmc: sdhci-brcmstb: Enable Clock Gating to save power
  mmc: sdhci-brcmstb: Re-organize flags
  mmc: mmci: Remove custom ios handler
  mmc: atmel-mci: Simplify if(chan) and if(!chan)
  mmc: core: use kobj_to_dev()
  dt-bindings: mmc: sdhci-of-dwcmhsc: Add rk3588
  mmc: core: Add CIDs for cards to the entropy pool
  mmc: core: Allows to override the timeout value for ioctl() path
  mmc: sdhci-omap: Use of_device_get_match_data() helper
  ...

Pull IPMI update from Corey Minyard:
 "Add limits on the number of users and messages, plus sysfs interfaces
  to control those limits.

  Other than that, little cleanups, use dev_xxx() insted of pr_xxx(),
  create initializers for structures, fix a refcount leak, etc"

* tag 'for-linus-4.19-1' of https://github.com/cminyard/linux-ipmi:
  ipmi:ipmb: Fix refcount leak in ipmi_ipmb_probe
  ipmi: remove unnecessary type castings
  ipmi: Make two logs unique
  ipmi:si: Convert pr_debug() to dev_dbg()
  ipmi: Convert pr_debug() to dev_dbg()
  ipmi: Fix pr_fmt to avoid compilation issues
  ipmi: Add an intializer for ipmi_recv_msg struct
  ipmi: Add an intializer for ipmi_smi_msg struct
  ipmi:ssif: Check for NULL msg when handling events and messages
  ipmi: use simple i2c probe function
  ipmi: Add a sysfs count of total outstanding messages for an interface
  ipmi: Add a sysfs interface to view the number of users
  ipmi: Limit the number of message a user may have outstanding
  ipmi: Add a limit on the number of users that may use IPMI

Pull mtd updates from Miquel Raynal:
 "MTD core changes:
   - Call of_platform_populate() for MTD partitions
   - Check devicetree alias for index
   - mtdoops:
      - Add a timestamp to the mtdoops header.
      - Create a header structure for the saved mtdoops.
      - Fix the size of the header read buffer.
   - mtdblock: Warn if opened on NAND
   - Bindings:
      - reserved-memory: Support MTD/block device
      - jedec,spi-nor: remove unneeded properties
      - Extend fixed-partitions binding
      - Add Sercomm (Suzhou) Corporation vendor prefix

  MTD driver changes:
   - st_spi_fsm: add missing clk_disable_unprepare() in stfsm_remove()
   - phram:
      - Allow cached mappings
      - Allow probing via reserved-memory
   - maps: ixp4xx: Drop driver
   - bcm47xxpart: Print correct offset on read error

  CFI driver changes:
   - Rename chip_ready variables
   - Add S29GL064N ID definition
   - Use chip_ready() for write on S29GL064N
   - Move and rename chip_check/chip_ready/chip_good_for_write

  NAND core changes:
   - Print offset instead of page number for bad blocks

  Raw NAND controller drivers:
   - Cadence: Fix possible null-ptr-deref in cadence_nand_dt_probe()
   - CS553X: simplify the return expression of cs553x_write_ctrl_byte()
   - Davinci: Remove redundant unsigned comparison to zero
   - Denali: Use managed device resources
   - GPMI:
      - Add large oob bch setting support
      - Rename the variable ecc_chunk_size
      - Uninline the gpmi_check_ecc function
      - Add strict ecc strength check
      - Refactor BCH geometry settings function
   - Intel: Fix possible null-ptr-deref in ebu_nand_probe()
   - MPC5121: Check before clk_disable_unprepare() not needed
   - Mtk:
      - MTD_NAND_ECC_MEDIATEK should depend on ARCH_MEDIATEK
      - Also parse the default nand-ecc-engine property if available
      - Make mtk_ecc.c a separated module
   - OMAP ELM:
      - Convert the bindings to yaml
      - Describe the bindings for AM64 ELM
      - Add support for its compatible
   - Renesas: Use runtime PM instead of the raw clock API and update the
     bindings accordingly
   - Rockchip: Check before clk_disable_unprepare() not needed
   - TMIO: Check return value after calling platform_get_resource()

  Raw NAND chip driver:
   - Kioxia: Add support for TH58NVG3S0HBAI4 and TC58NVG0S3HTA00

  SPI-NAND chip drivers:
   - Gigadevice:
      - Add support for:
         - GD5FxGM7xExxG
         - GD5F{2,4}GQ5xExxG
         - GD5F1GQ5RExxG
         - GD5FxGQ4xExxG
      - Fix Quad IO for GD5F1GQ5UExxG
   - XTX: Add support for XT26G0xA

  SPI NOR core changes:
   - Read back written SR value to make sure the write was done
     correctly.
   - Introduce a common function for Read ID that manufacturer drivers
     can use to verify the Octal DTR switch worked correctly.
   - Add helpers for read/write any register commands so manufacturer
     drivers don't open code it every time.
   - Clarify rdsr dummy cycles documentation.
   - Add debugfs entry to expose internal flash parameters and state.

  SPI NOR manufacturer drivers changes:
   - Add support for Winbond W25Q512NW-IM, and Eon EN25QH256A.
   - Move spi_nor_write_ear() to Winbond module since only Winbond
     flashes use it.
   - Rework Micron and Cypress Octal DTR enable methods to improve
     readability.
   - Use the common Read ID function to verify switch to Octal DTR mode
     for Micron and Cypress flashes.
   - Skip polling status on volatile register writes for Micron and
     Cypress flashes since the operation is instant"

* tag 'mtd/for-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (68 commits)
  mtd: st_spi_fsm: add missing clk_disable_unprepare() in stfsm_remove()
  dt-bindings: mtd: partitions: Extend fixed-partitions binding
  dt-bindings: Add Sercomm (Suzhou) Corporation vendor prefix
  mtd: phram: Allow cached mappings
  mtd: call of_platform_populate() for MTD partitions
  mtd: rawnand: renesas: Use runtime PM instead of the raw clock API
  dt-bindings: mtd: renesas: Fix the NAND controller description
  mtd: rawnand: mpc5121: Check before clk_disable_unprepare() not needed
  mtd: rawnand: rockchip: Check before clk_disable_unprepare() not needed
  mtd: nand: MTD_NAND_ECC_MEDIATEK should depend on ARCH_MEDIATEK
  mtd: rawnand: cs553x: simplify the return expression of cs553x_write_ctrl_byte()
  mtd: rawnand: kioxia: Add support for TH58NVG3S0HBAI4
  mtd: spi-nor: debugfs: fix format specifier
  mtd: spi-nor: support eon en25qh256a variant
  mtd: spi-nor: winbond: add support for W25Q512NW-IM
  mtd: spi-nor: expose internal parameters via debugfs
  mtd: spi-nor: export spi_nor_hwcaps_pp2cmd()
  mtd: spi-nor: move spi_nor_write_ear() to winbond module
  mtd: spi-nor: amend the rdsr dummy cycles documentation
  mtd: cfi_cmdset_0002: Rename chip_ready variables
  ...

Merge tag 'hwmon-for-v5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull hwmon updates from Guenter Roeck:
 "New drivers:

   - Driver for the Microchip LAN966x SoC

   - PMBus driver for Infineon Digital Multi-phase xdp152 family
     controllers

  Chip support added to existing drivers:

   - asus-ec-sensors:
      - Support for ROG STRIX X570-E GAMING WIFI II, PRIME X470-PRO, and
        ProArt X570 Creator WIFI
      - External temperature sensor support for ASUS WS X570-ACE

   - nct6775:
      - Support for I2C driver
      - Support for ASUS PRO H410T / PRIME H410M-R /
        ROG X570-E GAMING WIFI II

   - lm75:
      - Support for - Atmel AT30TS74

   - pmbus/max16601:
      - Support for MAX16602

   - aquacomputer_d5next:
      - Support for Aquacomputer Farbwerk
      - Support for Aquacomputer Octo

   - jc42:
      - Support for S-34TS04A

  Kernel API changes / clarifications:

   - The chip parameter of with_info API is now mandatory

   - New hwmon_device_register_for_thermal API call for use by the
     thermal subsystem

  Improvements:

   - PMBus and JC42 drivers now register with thermal subsystem

   - PMBus drivers now support get_voltage/set_voltage power operations

   - The adt7475 driver now supports pin configuration

   - The lm90 driver now supports setting extended range temperatures
     configuration with a devicetree property

   - The dell-smm driver now registers as cooling device

   - The OCC driver delays hwmon registration until requested by
     userspace

  ... and various other minor fixes and improvements"

* tag 'hwmon-for-v5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (71 commits)
  hwmon: (aquacomputer_d5next) Fix an error handling path in aqc_probe()
  hwmon: (sl28cpld) Fix typo in comment
  hwmon: (pmbus) Check PEC support before reading other registers
  hwmon: (dimmtemp) Fix bitmap handling
  hwmon: (lm90) enable extended range according to DTS node
  dt-bindings: hwmon: lm90: add ti,extended-range-enable property
  dt-bindings: hwmon: lm90: add missing ti,tmp461
  hwmon: (ibmaem) Directly use ida_alloc()/free()
  hwmon: Directly use ida_alloc()/free()
  hwmon: (asus-ec-sensors) fix Formula VIII definition
  dt-bindings: trivial-devices: Add xdp152
  hwmon: (sl28cpld-hwmon) Use HWMON_CHANNEL_INFO macro
  hwmon: (pwm-fan) Use HWMON_CHANNEL_INFO macro
  hwmon: (peci/dimmtemp) Use HWMON_CHANNEL_INFO macro
  hwmon: (peci/cputemp) Use HWMON_CHANNEL_INFO macro
  hwmon: (mr75203) Use HWMON_CHANNEL_INFO macro
  hwmon: (ltc2992) Use HWMON_CHANNEL_INFO macro
  hwmon: (as370-hwmon) Use HWMON_CHANNEL_INFO macro
  hwmon: Make chip parameter for with_info API mandatory
  thermal/drivers/thermal_hwmon: Use hwmon_device_register_for_thermal()
  ...

Pull IMA updates from Mimi Zohar:
 "New is IMA support for including fs-verity file digests and signatures
  in the IMA measurement list as well as verifying the fs-verity file
  digest based signatures, both based on policy.

  In addition, are two bug fixes:

   - avoid reading UEFI variables, which cause a page fault, on Apple
     Macs with T2 chips.

   - remove the original "ima" template Kconfig option to address a boot
     command line ordering issue.

  The rest is a mixture of code/documentation cleanup"

* tag 'integrity-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/zohar/linux-integrity:
  integrity: Fix sparse warnings in keyring_handler
  evm: Clean up some variables
  evm: Return INTEGRITY_PASS for enum integrity_status value '0'
  efi: Do not import certificates from UEFI Secure Boot for T2 Macs
  fsverity: update the documentation
  ima: support fs-verity file digest based version 3 signatures
  ima: permit fsverity's file digests in the IMA measurement list
  ima: define a new template field named 'd-ngv2' and templates
  fs-verity: define a function to return the integrity protected file digest
  ima: use IMA default hash algorithm for integrity violations
  ima: fix 'd-ng' comments and documentation
  ima: remove the IMA_TEMPLATE Kconfig option
  ima: remove redundant initialization of pointer 'file'.

Merge tag 'tpmdd-next-v5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jarkko/linux-tpmdd

Pull tpm updates from Jarkko Sakkinen:

 - Tightened validation of key hashes for SYSTEM_BLACKLIST_HASH_LIST. An
   invalid hash format causes a compilation error. Previously, they got
   included to the kernel binary but were silently ignored at run-time.

 - Allow root user to append new hashes to the blacklist keyring.

 - Trusted keys backed with Cryptographic Acceleration and Assurance
   Module (CAAM), which part of some of the new NXP's SoC's. Now there
   is total three hardware backends for trusted keys: TPM, ARM TEE and
   CAAM.

 - A scattered set of fixes and small improvements for the TPM driver.

* tag 'tpmdd-next-v5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jarkko/linux-tpmdd:
  MAINTAINERS: add KEYS-TRUSTED-CAAM
  doc: trusted-encrypted: describe new CAAM trust source
  KEYS: trusted: Introduce support for NXP CAAM-based trusted keys
  crypto: caam - add in-kernel interface for blob generator
  crypto: caam - determine whether CAAM supports blob encap/decap
  KEYS: trusted: allow use of kernel RNG for key material
  KEYS: trusted: allow use of TEE as backend without TCG_TPM support
  tpm: Add field upgrade mode support for Infineon TPM2 modules
  tpm: Fix buffer access in tpm2_get_tpm_pt()
  char: tpm: cr50_i2c: Suppress duplicated error message in .remove()
  tpm: cr50: Add new device/vendor ID 0x504a6666
  tpm: Remove read16/read32/write32 calls from tpm_tis_phy_ops
  tpm: ibmvtpm: Correct the return value in tpm_ibmvtpm_probe()
  tpm/tpm_ftpm_tee: Return true/false (not 1/0) from bool functions
  certs: Explain the rationale to call panic()
  certs: Allow root user to append signed hashes to the blacklist keyring
  certs: Check that builtin blacklist hashes are valid
  certs: Make blacklist_vet_description() more strict
  certs: Factor out the blacklist hash creation
  tools/certs: Add print-cert-tbs-hash.sh

Pull smack update from Casey Schaufler:
 "A single change to remove a pointless assignment"

* tag 'Smack-for-5.19' of https://github.com/cschaufler/smack-next:
  smack: Remove redundant assignments

Pull Landlock updates from Mickaël Salaün:

 - improve the path_rename LSM hook implementations for RENAME_EXCHANGE;

 - fix a too-restrictive filesystem control for a rare corner case;

 - set the nested sandbox limitation to 16 layers;

 - add a new LANDLOCK_ACCESS_FS_REFER access right to properly handle
   file reparenting (i.e. full rename and link support);

 - add new tests and documentation;

 - format code with clang-format to make it easier to maintain and
   contribute.

* tag 'landlock-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mic/linux: (30 commits)
  landlock: Explain how to support Landlock
  landlock: Add design choices documentation for filesystem access rights
  landlock: Document good practices about filesystem policies
  landlock: Document LANDLOCK_ACCESS_FS_REFER and ABI versioning
  samples/landlock: Add support for file reparenting
  selftests/landlock: Add 11 new test suites dedicated to file reparenting
  landlock: Add support for file reparenting with LANDLOCK_ACCESS_FS_REFER
  LSM: Remove double path_rename hook calls for RENAME_EXCHANGE
  landlock: Move filesystem helpers and add a new one
  landlock: Fix same-layer rule unions
  landlock: Create find_rule() from unmask_layers()
  landlock: Reduce the maximum number of layers to 16
  landlock: Define access_mask_t to enforce a consistent access mask size
  selftests/landlock: Test landlock_create_ruleset(2) argument check ordering
  landlock: Change landlock_restrict_self(2) check ordering
  landlock: Change landlock_add_rule(2) argument check ordering
  selftests/landlock: Add tests for O_PATH
  selftests/landlock: Fully test file rename with "remove" access
  selftests/landlock: Extend access right tests to directories
  selftests/landlock: Add tests for unknown access rights
  ...

Pull selinux updates from Paul Moore:
 "We've got twelve patches queued for v5.19, with most being fairly
  minor. The highlights are below:

   - The checkreqprot and runtime disable knobs have been deprecated for
     some time with no active users that we can find. In an effort to
     move things along we are adding a pause when the knobs are used to
     help make the deprecation more noticeable in case anyone is still
     using these hacks in the shadows.

   - We've added the anonymous inode class name to the AVC audit records
     when anonymous inodes are involved. This should make writing policy
     easier when anonymous inodes are involved.

   - More constification work. This is fairly straightforward and the
     source of most of the diffstat.

   - The usual minor cleanups: remove unnecessary assignments, assorted
     style/checkpatch fixes, kdoc fixes, macro while-loop
     encapsulations, #include tweaks, etc"

* tag 'selinux-pr-20220523' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux:
  security: declare member holding string literal const
  selinux: log anon inode class name
  selinux: declare data arrays const
  selinux: fix indentation level of mls_ops block
  selinux: include necessary headers in headers
  selinux: avoid extra semicolon
  selinux: update parameter documentation
  selinux: resolve checkpatch errors
  selinux: don't sleep when CONFIG_SECURITY_SELINUX_CHECKREQPROT_VALUE is true
  selinux: checkreqprot is deprecated, add some ssleep() discomfort
  selinux: runtime disable is deprecated, add some ssleep() discomfort
  selinux: Remove redundant assignments

Pull execve updates from Kees Cook:

 - Fix binfmt_flat GOT handling for riscv (Niklas Cassel)

 - Remove unused/broken binfmt_flat shared library and coredump code
   (Eric W. Biederman)

* tag 'execve-v5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  binfmt_flat: Remove shared library support
  binfmt_flat: Drop vestiges of coredump support
  binfmt_flat: do not stop relocating GOT entries prematurely on riscv

Pull seccomp updates from Kees Cook:

 - Rework USER_NOTIF notification ordering and kill logic (Sargun
   Dhillon)

 - Improved PTRACE_O_SUSPEND_SECCOMP selftest (Jann Horn)

 - Gracefully handle failed unshare() in selftests (Yang Guang)

 - Spelling fix (Colin Ian King)

* tag 'seccomp-v5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  selftests/seccomp: Fix spelling mistake "Coud" -> "Could"
  selftests/seccomp: Add test for wait killable notifier
  selftests/seccomp: Refactor get_proc_stat to split out file reading code
  seccomp: Add wait_killable semantic to seccomp user notifier
  selftests/seccomp: Ensure that notifications come in FIFO order
  seccomp: Use FIFO semantics to order notifications
  selftests/seccomp: Add SKIP for failed unshare()
  selftests/seccomp: Test PTRACE_O_SUSPEND_SECCOMP without CAP_SYS_ADMIN

Pull kernel hardening updates from Kees Cook:

 - usercopy hardening expanded to check other allocation types (Matthew
   Wilcox, Yuanzheng Song)

 - arm64 stackleak behavioral improvements (Mark Rutland)

 - arm64 CFI code gen improvement (Sami Tolvanen)

 - LoadPin LSM block dev API adjustment (Christoph Hellwig)

 - Clang randstruct support (Bill Wendling, Kees Cook)

* tag 'kernel-hardening-v5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (34 commits)
  loadpin: stop using bdevname
  mm: usercopy: move the virt_addr_valid() below the is_vmalloc_addr()
  gcc-plugins: randstruct: Remove cast exception handling
  af_unix: Silence randstruct GCC plugin warning
  niu: Silence randstruct warnings
  big_keys: Use struct for internal payload
  gcc-plugins: Change all version strings match kernel
  randomize_kstack: Improve docs on requirements/rationale
  lkdtm/stackleak: fix CONFIG_GCC_PLUGIN_STACKLEAK=n
  arm64: entry: use stackleak_erase_on_task_stack()
  stackleak: add on/off stack variants
  lkdtm/stackleak: check stack boundaries
  lkdtm/stackleak: prevent unexpected stack usage
  lkdtm/stackleak: rework boundary management
  lkdtm/stackleak: avoid spurious failure
  stackleak: rework poison scanning
  stackleak: rework stack high bound handling
  stackleak: clarify variable names
  stackleak: rework stack low bound handling
  stackleak: remove redundant check
  ...

Pull fsverity updates from Eric Biggers:
 "A couple small cleanups for fs/verity/"

* tag 'fsverity-for-linus' of git://git.kernel.org/pub/scm/fs/fscrypt/fscrypt:
  fs-verity: Use struct_size() helper in enable_verity()
  fs-verity: remove unused parameter desc_size in fsverity_create_info()

Pull fscrypt updates from Eric Biggers:
 "Some cleanups for fs/crypto/:

   - Split up the misleadingly-named FS_CRYPTO_BLOCK_SIZE constant.

   - Consistently report the encryption implementation that is being
     used.

   - Add helper functions for the test_dummy_encryption mount option
     that work properly with the new mount API. ext4 and f2fs will use
     these"

* tag 'fscrypt-for-linus' of git://git.kernel.org/pub/scm/fs/fscrypt/fscrypt:
  fscrypt: add new helper functions for test_dummy_encryption
  fscrypt: factor out fscrypt_policy_to_key_spec()
  fscrypt: log when starting to use inline encryption
  fscrypt: split up FS_CRYPTO_BLOCK_SIZE

Pull random number generator updates from Jason Donenfeld:
 "These updates continue to refine the work began in 5.17 and 5.18 of
  modernizing the RNG's crypto and streamlining and documenting its
  code.

  New for 5.19, the updates aim to improve entropy collection methods
  and make some initial decisions regarding the "premature next" problem
  and our threat model. The cloc utility now reports that random.c is
  931 lines of code and 466 lines of comments, not that basic metrics
  like that mean all that much, but at the very least it tells you that
  this is very much a manageable driver now.

  Here's a summary of the various updates:

   - The random_get_entropy() function now always returns something at
     least minimally useful. This is the primary entropy source in most
     collectors, which in the best case expands to something like RDTSC,
     but prior to this change, in the worst case it would just return 0,
     contributing nothing. For 5.19, additional architectures are wired
     up, and architectures that are entirely missing a cycle counter now
     have a generic fallback path, which uses the highest resolution
     clock available from the timekeeping subsystem.

     Some of those clocks can actually be quite good, despite the CPU
     not having a cycle counter of its own, and going off-core for a
     stamp is generally thought to increase jitter, something positive
     from the perspective of entropy gathering. Done very early on in
     the development cycle, this has been sitting in next getting some
     testing for a while now and has relevant acks from the archs, so it
     should be pretty well tested and fine, but is nonetheless the thing
     I'll be keeping my eye on most closely.

   - Of particular note with the random_get_entropy() improvements is
     MIPS, which, on CPUs that lack the c0 count register, will now
     combine the high-speed but short-cycle c0 random register with the
     lower-speed but long-cycle generic fallback path.

   - With random_get_entropy() now always returning something useful,
     the interrupt handler now collects entropy in a consistent
     construction.

   - Rather than comparing two samples of random_get_entropy() for the
     jitter dance, the algorithm now tests many samples, and uses the
     amount of differing ones to determine whether or not jitter entropy
     is usable and how laborious it must be. The problem with comparing
     only two samples was that if the cycle counter was extremely slow,
     but just so happened to be on the cusp of a change, the slowness
     wouldn't be detected. Taking many samples fixes that to some
     degree.

     This, combined with the other improvements to random_get_entropy(),
     should make future unification of /dev/random and /dev/urandom
     maybe more possible. At the very least, were we to attempt it again
     today (we're not), it wouldn't break any of Guenter's test rigs
     that broke when we tried it with 5.18. So, not today, but perhaps
     down the road, that's something we can revisit.

   - We attempt to reseed the RNG immediately upon waking up from system
     suspend or hibernation, making use of the various timestamps about
     suspend time and such available, as well as the usual inputs such
     as RDRAND when available.

   - Batched randomness now falls back to ordinary randomness before the
     RNG is initialized. This provides more consistent guarantees to the
     types of random numbers being returned by the various accessors.

   - The "pre-init injection" code is now gone for good. I suspect you
     in particular will be happy to read that, as I recall you
     expressing your distaste for it a few months ago. Instead, to avoid
     a "premature first" issue, while still allowing for maximal amount
     of entropy availability during system boot, the first 128 bits of
     estimated entropy are used immediately as it arrives, with the next
     128 bits being buffered. And, as before, after the RNG has been
     fully initialized, it winds up reseeding anyway a few seconds later
     in most cases. This resulted in a pretty big simplification of the
     initialization code and let us remove various ad-hoc mechanisms
     like the ugly crng_pre_init_inject().

   - The RNG no longer pretends to handle the "premature next" security
     model, something that various academics and other RNG designs have
     tried to care about in the past. After an interesting mailing list
     thread, these issues are thought to be a) mainly academic and not
     practical at all, and b) actively harming the real security of the
     RNG by delaying new entropy additions after a potential compromise,
     making a potentially bad situation even worse. As well, in the
     first place, our RNG never even properly handled the premature next
     issue, so removing an incomplete solution to a fake problem was
     particularly nice.

     This allowed for numerous other simplifications in the code, which
     is a lot cleaner as a consequence. If you didn't see it before,
     https://lore.kernel.org/lkml/YmlMGx6+uigkGiZ0@zx2c4.com/ may be a
     thread worth skimming through.

   - While the interrupt handler received a separate code path years ago
     that avoids locks by using per-cpu data structures and a faster
     mixing algorithm, in order to reduce interrupt latency, input and
     disk events that are triggered in hardirq handlers were still
     hitting locks and more expensive algorithms. Those are now
     redirected to use the faster per-cpu data structures.

   - Rather than having the fake-crypto almost-siphash-based random32
     implementation be used right and left, and in many places where
     cryptographically secure randomness is desirable, the batched
     entropy code is now fast enough to replace that.

   - As usual, numerous code quality and documentation cleanups. For
     example, the initialization state machine now uses enum symbolic
     constants instead of just hard coding numbers everywhere.

   - Since the RNG initializes once, and then is always initialized
     thereafter, a pretty heavy amount of code used during that
     initialization is never used again. It is now completely cordoned
     off using static branches and it winds up in the .text.unlikely
     section so that it doesn't reduce cache compactness after the RNG
     is ready.

   - A variety of functions meant for waiting on the RNG to be
     initialized were only used by vsprintf, and in not a particularly
     optimal way. Replacing that usage with a more ordinary setup made
     it possible to remove those functions.

   - A cleanup of how we warn userspace about the use of uninitialized
     /dev/urandom and uninitialized get_random_bytes() usage.
     Interestingly, with the change you merged for 5.18 that attempts to
     use jitter (but does not block if it can't), the majority of users
     should never see those warnings for /dev/urandom at all now, and
     the one for in-kernel usage is mainly a debug thing.

   - The file_operations struct for /dev/[u]random now implements
     .read_iter and .write_iter instead of .read and .write, allowing it
     to also implement .splice_read and .splice_write, which makes
     splice(2) work again after it was broken here (and in many other
     places in the tree) during the set_fs() removal. This was a bit of
     a last minute arrival from Jens that hasn't had as much time to
     bake, so I'll be keeping my eye on this as well, but it seems
     fairly ordinary. Unfortunately, read_iter() is around 3% slower
     than read() in my tests, which I'm not thrilled about. But Jens and
     Al, spurred by this observation, seem to be making progress in
     removing the bottlenecks on the iter paths in the VFS layer in
     general, which should remove the performance gap for all drivers.

   - Assorted other bug fixes, cleanups, and optimizations.

   - A small SipHash cleanup"

* tag 'random-5.19-rc1-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random: (49 commits)
  random: check for signals after page of pool writes
  random: wire up fops->splice_{read,write}_iter()
  random: convert to using fops->write_iter()
  random: convert to using fops->read_iter()
  random: unify batched entropy implementations
  random: move randomize_page() into mm where it belongs
  random: remove mostly unused async readiness notifier
  random: remove get_random_bytes_arch() and add rng_has_arch_random()
  random: move initialization functions out of hot pages
  random: make consistent use of buf and len
  random: use proper return types on get_random_{int,long}_wait()
  random: remove extern from functions in header
  random: use static branch for crng_ready()
  random: credit architectural init the exact amount
  random: handle latent entropy and command line from random_init()
  random: use proper jiffies comparison macro
  random: remove ratelimiting for in-kernel unseeded randomness
  random: move initialization out of reseeding hot path
  random: avoid initializing twice in credit race
  random: use symbolic constants for crng_init states
  ...

KGDB and KDB allow read and write access to kernel memory, and thus
should be restricted during lockdown.  An attacker with access to a
serial port (for example, via a hypervisor console, which some cloud
vendors provide over the network) could trigger the debugger so it is
important that the debugger respect the lockdown mode when/if it is
triggered.

Fix this by integrating lockdown into kdb's existing permissions
mechanism.  Unfortunately kgdb does not have any permissions mechanism
(although it certainly could be added later) so, for now, kgdb is simply
and brutally disabled by immediately exiting the gdb stub without taking
any action.

For lockdowns established early in the boot (e.g. the normal case) then
this should be fine but on systems where kgdb has set breakpoints before
the lockdown is enacted than "bad things" will happen.

CVE: CVE-2022-21499
Co-developed-by: Stephen Brennan <stephen.s.brennan@oracle.com>
Signed-off-by: Stephen Brennan <stephen.s.brennan@oracle.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull scheduler updates from Ingo Molnar:

 - Updates to scheduler metrics:
     - PELT fixes & enhancements
     - PSI fixes & enhancements
     - Refactor cpu_util_without()

 - Updates to instrumentation/debugging:
     - Remove sched_trace_*() helper functions - can be done via debug
       info
     - Fix double update_rq_clock() warnings

 - Introduce & use "preemption model accessors" to simplify some of the
   Kconfig complexity.

 - Make softirq handling RT-safe.

 - Misc smaller fixes & cleanups.

* tag 'sched-core-2022-05-23' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  topology: Remove unused cpu_cluster_mask()
  sched: Reverse sched_class layout
  sched/deadline: Remove superfluous rq clock update in push_dl_task()
  sched/core: Avoid obvious double update_rq_clock warning
  smp: Make softirq handling RT safe in flush_smp_call_function_queue()
  smp: Rename flush_smp_call_function_from_idle()
  sched: Fix missing prototype warnings
  sched/fair: Remove cfs_rq_tg_path()
  sched/fair: Remove sched_trace_*() helper functions
  sched/fair: Refactor cpu_util_without()
  sched/fair: Revise comment about lb decision matrix
  sched/psi: report zeroes for CPU full at the system level
  sched/fair: Delete useless condition in tg_unthrottle_up()
  sched/fair: Fix cfs_rq_clock_pelt() for throttled cfs_rq
  sched/fair: Move calculate of avg_load to a better location
  mailmap: Update my email address to @redhat.com
  MAINTAINERS: Add myself as scheduler topology reviewer
  psi: Fix trigger being fired unexpectedly at initial
  ftrace: Use preemption model accessors for trace header printout
  kcsan: Use preemption model accessors

Pull perf events updates from Ingo Molnar:
 "Platform PMU changes:

   - x86/intel:
      - Add new Intel Alder Lake and Raptor Lake support

   - x86/amd:
      - AMD Zen4 IBS extensions support
      - Add AMD PerfMonV2 support
      - Add AMD Fam19h Branch Sampling support

  Generic changes:

   - signal: Deliver SIGTRAP on perf event asynchronously if blocked

     Perf instrumentation can be driven via SIGTRAP, but this causes a
     problem when SIGTRAP is blocked by a task & terminate the task.

     Allow user-space to request these signals asynchronously (after
     they get unblocked) & also give the information to the signal
     handler when this happens:

       "To give user space the ability to clearly distinguish
        synchronous from asynchronous signals, introduce
        siginfo_t::si_perf_flags and TRAP_PERF_FLAG_ASYNC (opted for
        flags in case more binary information is required in future).

        The resolution to the problem is then to (a) no longer force the
        signal (avoiding the terminations), but (b) tell user space via
        si_perf_flags if the signal was synchronous or not, so that such
        signals can be handled differently (e.g. let user space decide
        to ignore or consider the data imprecise). "

   - Unify/standardize the /sys/devices/cpu/events/* output format.

   - Misc fixes & cleanups"

* tag 'perf-core-2022-05-23' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (32 commits)
  perf/x86/amd/core: Fix reloading events for SVM
  perf/x86/amd: Run AMD BRS code only on supported hw
  perf/x86/amd: Fix AMD BRS period adjustment
  perf/x86/amd: Remove unused variable 'hwc'
  perf/ibs: Fix comment
  perf/amd/ibs: Advertise zen4_ibs_extensions as pmu capability attribute
  perf/amd/ibs: Add support for L3 miss filtering
  perf/amd/ibs: Use ->is_visible callback for dynamic attributes
  perf/amd/ibs: Cascade pmu init functions' return value
  perf/x86/uncore: Add new Alder Lake and Raptor Lake support
  perf/x86/uncore: Clean up uncore_pci_ids[]
  perf/x86/cstate: Add new Alder Lake and Raptor Lake support
  perf/x86/msr: Add new Alder Lake and Raptor Lake support
  perf/x86: Add new Alder Lake and Raptor Lake support
  perf/amd/ibs: Use interrupt regs ip for stack unwinding
  perf/x86/amd/core: Add PerfMonV2 overflow handling
  perf/x86/amd/core: Add PerfMonV2 counter control
  perf/x86/amd/core: Detect available counters
  perf/x86/amd/core: Detect PerfMonV2 support
  x86/msr: Add PerfCntrGlobal* registers
  ...

Pull objtool updates from Ingo Molnar:

 - Comprehensive interface overhaul:
   =================================

   Objtool's interface has some issues:

     - Several features are done unconditionally, without any way to
       turn them off. Some of them might be surprising. This makes
       objtool tricky to use, and prevents porting individual features
       to other arches.

     - The config dependencies are too coarse-grained. Objtool
       enablement is tied to CONFIG_STACK_VALIDATION, but it has several
       other features independent of that.

     - The objtool subcmds ("check" and "orc") are clumsy: "check" is
       really a subset of "orc", so it has all the same options.

       The subcmd model has never really worked for objtool, as it only
       has a single purpose: "do some combination of things on an object
       file".

     - The '--lto' and '--vmlinux' options are nonsensical and have
       surprising behavior.

   Overhaul the interface:

      - get rid of subcmds

      - make all features individually selectable

      - remove and/or clarify confusing/obsolete options

      - update the documentation

      - fix some bugs found along the way

 - Fix x32 regression

 - Fix Kbuild cleanup bugs

 - Add scripts/objdump-func helper script to disassemble a single
   function from an object file.

 - Rewrite scripts/faddr2line to be section-aware, by basing it on
   'readelf', moving it away from 'nm', which doesn't handle multiple
   sections well, which can result in decoding failure.

 - Rewrite & fix symbol handling - which had a number of bugs wrt.
   object files that don't have global symbols - which is rare but
   possible. Also fix a bunch of symbol handling bugs found along the
   way.

* tag 'objtool-core-2022-05-23' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
  objtool: Fix objtool regression on x32 systems
  objtool: Fix symbol creation
  scripts/faddr2line: Fix overlapping text section failures
  scripts: Create objdump-func helper script
  objtool: Remove libsubcmd.a when make clean
  objtool: Remove inat-tables.c when make clean
  objtool: Update documentation
  objtool: Remove --lto and --vmlinux in favor of --link
  objtool: Add HAVE_NOINSTR_VALIDATION
  objtool: Rename "VMLINUX_VALIDATION" -> "NOINSTR_VALIDATION"
  objtool: Make noinstr hacks optional
  objtool: Make jump label hack optional
  objtool: Make static call annotation optional
  objtool: Make stack validation frame-pointer-specific
  objtool: Add CONFIG_OBJTOOL
  objtool: Extricate sls from stack validation
  objtool: Rework ibt and extricate from stack validation
  objtool: Make stack validation optional
  objtool: Add option to print section addresses
  objtool: Don't print parentheses in function addresses
  ...

Pull locking updates from Ingo Molnar:

 - rwsem cleanups & optimizations/fixes:
    - Conditionally wake waiters in reader/writer slowpaths
    - Always try to wake waiters in out_nolock path

 - Add try_cmpxchg64() implementation, with arch optimizations - and use
   it to micro-optimize sched_clock_{local,remote}()

 - Various force-inlining fixes to address objdump instrumentation-check
   warnings

 - Add lock contention tracepoints:

    lock:contention_begin
    lock:contention_end

 - Misc smaller fixes & cleanups

* tag 'locking-core-2022-05-23' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/clock: Use try_cmpxchg64 in sched_clock_{local,remote}
  locking/atomic/x86: Introduce arch_try_cmpxchg64
  locking/atomic: Add generic try_cmpxchg64 support
  futex: Remove a PREEMPT_RT_FULL reference.
  locking/qrwlock: Change "queue rwlock" to "queued rwlock"
  lockdep: Delete local_irq_enable_in_hardirq()
  locking/mutex: Make contention tracepoints more consistent wrt adaptive spinning
  locking: Apply contention tracepoints in the slow path
  locking: Add lock contention tracepoints
  locking/rwsem: Always try to wake waiters in out_nolock path
  locking/rwsem: Conditionally wake waiters in reader/writer slowpaths
  locking/rwsem: No need to check for handoff bit if wait queue empty
  lockdep: Fix -Wunused-parameter for _THIS_IP_
  x86/mm: Force-inline __phys_addr_nodebug()
  x86/kvm/svm: Force-inline GHCB accessors
  task_stack, x86/cea: Force-inline stack helpers

- support for pens with 3 buttons (Joshua Dickens)
- support for HID_DG_SCANTIME to report the timestamp for pen and touch events
  (Joshua Dickens)

- support for wider variety of Huion tablets ported from DIGImend
  project (José Expósito, Nikolai Kondrashov)