[This will be used by the ad193x driver to fix the fact that the
original author of the driver put a bodge for their particular chip into
a the generic ASoC register I/O abstraction layer which looked like an
obvious bug which ended up getting fixed in 3.0.  Sadly there were no
comments documenting what was going on.  A minimally invasive correction
to the driver is to remove the register cache support and go direct to
the hardware all the time so we're adding a new feature -- broonie]
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

system clock is 24.576MHz instead of 12.288MHz
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

dac word len value should left shift before setting
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Acked-by: Barry Song <21cnbao@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

fix dac word len mask and adc tdm fmt shift value
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

request_any_context_irq() returns a negative value on failure.
On success, it returns either IRQC_IS_HARDIRQ or IRQC_IS_NESTED.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.orG

Add linux/types.h to fix this compilation error:

In file included from arch/arm/mach-s3c2410/include/mach/gpio-fns.h:27:0,
                 from arch/arm/mach-s3c2410/include/mach/gpio.h:27,
                 from /home/anarsoul/work/pda-linux/linux-next/arch/arm/include/asm/gpio.h:5,
                 from include/linux/gpio.h:18,
                 from sound/soc/samsung/rx1950_uda1380.c:20:
arch/arm/plat-samsung/include/plat/gpio-cfg.h:29:34: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘s3c_gpio_pull_t’
arch/arm/plat-samsung/include/plat/gpio-cfg.h:30:34: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘s5p_gpio_drvstr_t’
arch/arm/plat-samsung/include/plat/gpio-cfg.h:57:2: error: expected specifier-qualifier-list before ‘s3c_gpio_pull_t’
arch/arm/plat-samsung/include/plat/gpio-cfg.h:148:47: error: expected declaration specifiers or ‘...’ before ‘s3c_gpio_pull_t’
arch/arm/plat-samsung/include/plat/gpio-cfg.h:156:24: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘s3c_gpio_getpull’
arch/arm/plat-samsung/include/plat/gpio-cfg.h:175:24: error: expected declaration specifiers or ‘...’ before ‘s3c_gpio_pull_t’
arch/arm/plat-samsung/include/plat/gpio-cfg.h: In function ‘s3c_gpio_cfgrange_nopull’:
arch/arm/plat-samsung/include/plat/gpio-cfg.h:180:47: error: ‘s3c_gpio_pull_t’ undeclared (first use in this function)
arch/arm/plat-samsung/include/plat/gpio-cfg.h:180:47: note: each undeclared identifier is reported only once for each function it appears in
arch/arm/plat-samsung/include/plat/gpio-cfg.h:180:47: error: expected ‘)’ before numeric constant
arch/arm/plat-samsung/include/plat/gpio-cfg.h:180:47: error: too many arguments to function ‘s3c_gpio_cfgall_range’
arch/arm/plat-samsung/include/plat/gpio-cfg.h:174:12: note: declared here
arch/arm/plat-samsung/include/plat/gpio-cfg.h: At top level:
arch/arm/plat-samsung/include/plat/gpio-cfg.h:199:26: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘s5p_gpio_get_drvstr’
arch/arm/plat-samsung/include/plat/gpio-cfg.h:210:50: error: expected declaration specifiers or ‘...’ before ‘s5p_gpio_drvstr_t’
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Add linux/types.h to fix this compilation error:

In file included from arch/arm/mach-s3c2410/include/mach/gpio-fns.h:27:0,
                 from arch/arm/mach-s3c2410/include/mach/gpio.h:27,
                 from /home/anarsoul/work/pda-linux/linux-next/arch/arm/include/asm/gpio.h:5,
                 from include/linux/gpio.h:18,
                 from sound/soc/samsung/rx1950_uda1380.c:20:
arch/arm/plat-samsung/include/plat/gpio-cfg.h:29:34: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘s3c_gpio_pull_t’
arch/arm/plat-samsung/include/plat/gpio-cfg.h:30:34: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘s5p_gpio_drvstr_t’
arch/arm/plat-samsung/include/plat/gpio-cfg.h:57:2: error: expected specifier-qualifier-list before ‘s3c_gpio_pull_t’
arch/arm/plat-samsung/include/plat/gpio-cfg.h:148:47: error: expected declaration specifiers or ‘...’ before ‘s3c_gpio_pull_t’
arch/arm/plat-samsung/include/plat/gpio-cfg.h:156:24: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘s3c_gpio_getpull’
arch/arm/plat-samsung/include/plat/gpio-cfg.h:175:24: error: expected declaration specifiers or ‘...’ before ‘s3c_gpio_pull_t’
arch/arm/plat-samsung/include/plat/gpio-cfg.h: In function ‘s3c_gpio_cfgrange_nopull’:
arch/arm/plat-samsung/include/plat/gpio-cfg.h:180:47: error: ‘s3c_gpio_pull_t’ undeclared (first use in this function)
arch/arm/plat-samsung/include/plat/gpio-cfg.h:180:47: note: each undeclared identifier is reported only once for each function it appears in
arch/arm/plat-samsung/include/plat/gpio-cfg.h:180:47: error: expected ‘)’ before numeric constant
arch/arm/plat-samsung/include/plat/gpio-cfg.h:180:47: error: too many arguments to function ‘s3c_gpio_cfgall_range’
arch/arm/plat-samsung/include/plat/gpio-cfg.h:174:12: note: declared here
arch/arm/plat-samsung/include/plat/gpio-cfg.h: At top level:
arch/arm/plat-samsung/include/plat/gpio-cfg.h:199:26: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘s5p_gpio_get_drvstr’
arch/arm/plat-samsung/include/plat/gpio-cfg.h:210:50: error: expected declaration specifiers or ‘...’ before ‘s5p_gpio_drvstr_t’
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

When the clocking registers are not overriden some of the registers are
not writable.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Cc: stable@kernel.org

sound/soc/codecs/wm8750.c:784:2: warning: missing braces around initializer
sound/soc/codecs/wm8750.c:784:2: warning: (near initialization for ‘wm8750_spi_ids[2].name’)

It's because struct spi_device_id.name is a char array, not a pointer,
while the driver initializes explicitly with 0.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

My gmail account got disabled and I'm not going to reopen it.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

I2S in Exynos4 and S5PC110(S5PV210) has a internal dma.
It can be used low power audio mode and 2nd channel transfer.
This patch can support idma.

[Reapplied after dependencies propagated through in 3.1-rc1. --broonie]
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>

This error would have no effect on current silicon revisions, the fall
through case has the same behaviour.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

As we had no id_table only the driver name would be matched against
meaning that WM8987 devices wouldn't be bound.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

The I2C address is misformatted and would never match.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Cc: stable@kernel.org

Without this, request_irq on subsequent device initialization fails, and
the codec cannot be used.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Two issues were preventing module snd-soc-tegra-wm8903.ko from being
removed and re-inserted:

a) The speaker-enable GPIO is hosted by the WM8903 chip. This GPIO must
   be freed before snd_soc_unregister_card() is called, because that
   triggers wm8903.c:wm8903_remove(), which calls gpiochip_remove(), which
   then fails if any of the GPIOs are in use. To solve this, free all GPIOs
   first, so the code doesn't care where they come from.

b) We need to call snd_soc_jack_free_gpios() to match the call to
   snd_soc_jack_add_gpios() during initialization. Without this, the
   call to snd_soc_jack_add_gpios() fails during any subsequent modprobe
   and initialization, since the GPIO and IRQ are already registered. In
   turn, this causes the headphone state not to be monitored, so the
   headphone is assumed not to be plugged in, and the audio path to it is
   never enabled.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Cc: stable@kernel.org
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Not all PCM devices have all sub-streams. Specifically, the SPDIF driver
only supports playback and hence has no capture substream. Check whether
a substream exists before dereferencing it, when de-allocating DMA
buffers in tegra_pcm_deallocate_dma_buffer.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

Merge branch 'fix/asoc' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6 into for-3.1

Merge branch 'wm8996-rename' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound-2.6 into fix/asoc

Merge branch 'for-3.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound-2.6.git into for-3.1

This closes the small race between a status being read in response to an
interrupt and clearing the interrupt, meaning that if the status changes
between those periods we might not get a reassertion of the interrupt.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

For marketing reasons the part will be called WM8996. In order to avoid
user confusion rename the driver to reflect this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Liam Girdwood <lrg@ti.com>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  sparc: Fix build with DEBUG_PAGEALLOC enabled.

Commit d006199e72a9 ("serial: sh-sci: Regtype probing doesn't need to be
fatal.") made sci_init_single() return when sci_probe_regmap() succeeds,
although it should return when sci_probe_regmap() fails.  This causes
systems using the serial sh-sci driver to crash during boot.

Fix the problem by using the right return condition.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The generic library code already exports the generic function, this was
left-over from the ARM-specific version that just got removed.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Since commit 1eb19a12 ("lib/sha1: use the git implementation of
SHA-1"), the ARM SHA1 routines no longer work.  The reason? They
depended on the larger 320-byte workspace, and now the sha1 workspace is
just 16 words (64 bytes).  So the assembly version would overwrite the
stack randomly.

The optimized asm version is also probably slower than the new improved
C version, so there's no reason to keep it around.  At least that was
the case in git, where what appears to be the same assembly language
version was removed two years ago because the optimized C BLK_SHA1 code
was faster.
Reported-and-tested-by: Joachim Eastwood <manabian@gmail.com>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Cc: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

task->cred is declared as __rcu, and access to other tasks' ->cred is,
indeed, protected.  Access to current->cred does not need rcu_dereference()
at all, since only the task itself can change its ->cred.  sparse, of
course, has no way of knowing that...

Add force-cast in current_cred(), make current_fsuid() et.al. use it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Al points out that the do_follow_link() helper function really is
misnamed - it's about whether we should try to follow a symlink or not,
not about actually doing the following.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

After commit 3567866b: "RCUify freeing acls, let check_acl() go ahead in
RCU mode if acl is cached" posix_acl_permission is being called with an
unsupported flag and the permission check fails. This patch fixes the issue.
Signed-off-by: Ari Savolainen <ari.m.savolainen@gmail.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

* 'for-linus' of git://git.open-osd.org/linux-open-osd:
  ore: Make ore its own module
  exofs: Rename raid engine from exofs/ios.c => ore
  exofs: ios: Move to a per inode components & device-table
  exofs: Move exofs specific osd operations out of ios.c
  exofs: Add offset/length to exofs_get_io_state
  exofs: Fix truncate for the raid-groups case
  exofs: Small cleanup of exofs_fill_super
  exofs: BUG: Avoid sbi realloc
  exofs: Remove pnfs-osd private definitions
  nfs_xdr: Move nfs4_string definition out of #ifdef CONFIG_NFS_V4

The inode structure layout is largely random, and some of the vfs paths
really do care.  The path lookup in particular is already quite D$
intensive, and profiles show that accessing the 'inode->i_op->xyz'
fields is quite costly.

We already optimized the dcache to not unnecessarily load the d_op
structure for members that are often NULL using the DCACHE_OP_xyz bits
in dentry->d_flags, and this does something very similar for the inode
ops that are used during pathname lookup.

It also re-orders the fields so that the fields accessed by 'stat' are
together at the beginning of the inode structure, and roughly in the
order accessed.

The effect of this seems to be in the 1-2% range for an empty kernel
"make -j" run (which is fairly kernel-intensive, mostly in filename
lookup), so it's visible.  The numbers are fairly noisy, though, and
likely depend a lot on exact microarchitecture.  So there's more tuning
to be done.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Gcc tends to generate better code with small integers, including the
DCACHE_xyz flag tests - so move the common ones to be first in the list.
Also just remove the unused DCACHE_INOTIFY_PARENT_WATCHED and
DCACHE_AUTOFS_PENDING values, their users no longer exists in the source
tree.

And add a "unlikely()" to the DCACHE_OP_COMPARE test, since we want the
common case to be a nice straight-line fall-through.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  net: Compute protocol sequence numbers and fragment IDs using MD5.
  crypto: Move md5_transform to lib/md5.c

Export everything from ore need exporting. Change Kbuild and Kconfig
to build ore.ko as an independent module. Import ore from exofs
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>

ORE stands for "Objects Raid Engine"

This patch is a mechanical rename of everything that was in ios.c
and its API declaration to an ore.c and an osd_ore.h header. The ore
engine will later be used by the pnfs objects layout driver.

* File ios.c => ore.c

* Declaration of types and API are moved from exofs.h to a new
  osd_ore.h

* All used types are prefixed by ore_ from their exofs_ name.

* Shift includes from exofs.h to osd_ore.h so osd_ore.h is
  independent, include it from exofs.h.

Other than a pure rename there are no other changes. Next patch
will move the ore into it's own module and will export the API
to be used by exofs and later the layout driver
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>