- 16 Aug, 2024 17 commits
-
-
Jakub Kicinski authored
Jason Wang says: ==================== virtio-net: synchronize op/admin state This series tries to synchronize the operstate with the admin state which allows the lower virtio-net to propagate the link status to the upper devices like macvlan. This is done by toggling carrier during ndo_open/stop while doing other necessary serialization about the carrier settings during probe. While at it, also fix a race between probe and ndo_set_features as we didn't initalize the guest offload setting under rtnl lock. ==================== Link: https://patch.msgid.link/20240814052228.4654-1-jasowang@redhat.comSigned-off-by:
Jakub Kicinski <kuba@kernel.org>
-
Jason Wang authored
We calculate guest offloads during probe without the protection of rtnl_lock. This lead to race between probe and ndo_set_features. Fix this by moving the calculation under the rtnl_lock. Fixes: 3f93522f ("virtio-net: switch off offloads on demand if possible on XDP set") Acked-by:
Michael S. Tsirkin <mst@redhat.com> Signed-off-by:
Jason Wang <jasowang@redhat.com> Link: https://patch.msgid.link/20240814052228.4654-5-jasowang@redhat.comSigned-off-by:
-
Jason Wang authored
This patch synchronizes operstate with admin state per RFC2863. This is done by trying to toggle the carrier upon open/close and synchronize with the config change work. This allows to propagate status correctly to stacked devices like: ip link add link enp0s3 macvlan0 type macvlan ip link set link enp0s3 down ip link show Before this patch: 3: enp0s3: <BROADCAST,MULTICAST> mtu 1500 qdisc pfifo_fast state DOWN mode DEFAULT group default qlen 1000 link/ether 00:00:05:00:00:09 brd ff:ff:ff:ff:ff:ff ...... 5: macvlan0@enp0s3: <BROADCAST,MULTICAST,UP,LOWER_UP,M-DOWN> mtu 1500 qdisc noqueue state UP mode DEFAULT group default qlen 1000 link/ether b2:a9:c5:04:da:53 brd ff:ff:ff:ff:ff:ff After this patch: 3: enp0s3: <BROADCAST,MULTICAST> mtu 1500 qdisc pfifo_fast state DOWN mode DEFAULT group default qlen 1000 link/ether 00:00:05:00:00:09 brd ff:ff:ff:ff:ff:ff ... 5: macvlan0@enp0s3: <NO-CARRIER,BROADCAST,MULTICAST,UP,M-DOWN> mtu 1500 qdisc noqueue state LOWERLAYERDOWN mode DEFAULT group default qlen 1000 link/ether b2:a9:c5:04:da:53 brd ff:ff:ff:ff:ff:ff Cc: Venkat Venkatsubra <venkat.x.venkatsubra@oracle.com> Cc: Gia-Khanh Nguyen <gia-khanh.nguyen@oracle.com> Acked-by: -
Jason Wang authored
Sometime, it would be useful to disable the configure change notification from the driver. So this patch allows this by introducing a variable config_change_driver_disabled and only allow the configure change notification callback to be triggered when it is allowed by both the virtio core and the driver. It is set to false by default to hold the current semantic so we don't need to change any drivers. The first user for this would be virtio-net. Cc: Venkat Venkatsubra <venkat.x.venkatsubra@oracle.com> Cc: Gia-Khanh Nguyen <gia-khanh.nguyen@oracle.com> Acked-by:
-
Jason Wang authored
Following patch will allow the config interrupt to be disabled by a specific driver via another boolean. So this patch renames virtio_config_enabled and relevant helpers to virtio_config_core_enabled. Cc: Venkat Venkatsubra <venkat.x.venkatsubra@oracle.com> Cc: Gia-Khanh Nguyen <gia-khanh.nguyen@oracle.com> Acked-by:
-
Uros Bizjak authored
Add missing __percpu qualifier to a (void *) cast to fix dev.c:10863:45: warning: cast removes address space '__percpu' of expression sparse warning. Also remove now unneeded __force sparse directives. Found by GCC's named address space checks. There were no changes in the resulting object file. Signed-off-by:
Uros Bizjak <ubizjak@gmail.com> Link: https://patch.msgid.link/20240814070748.943671-1-ubizjak@gmail.comSigned-off-by:
-
Xin Long authored
Similar to commit 70f06c11 ("sched: act_ct: switch to per-action label counting"), we should also switch to per-action label counting in openvswitch conntrack, as Florian suggested. The difference is that nf_connlabels_get() is called unconditionally when creating an ct action in ovs_ct_copy_action(). As with these flows: table=0,ip,actions=ct(commit,table=1) table=1,ip,actions=ct(commit,exec(set_field:0xac->ct_label),table=2) it needs to make sure the label ext is created in the 1st flow before the ct is committed in ovs_ct_commit(). Otherwise, the warning in nf_ct_ext_add() when creating the label ext in the 2nd flow will be triggered: WARN_ON(nf_ct_is_confirmed(ct)); Signed-off-by:
Xin Long <lucien.xin@gmail.com> Reviewed-by:
Aaron Conole <aconole@redhat.com> Acked-by:
Florian Westphal <fw@strlen.de> Link: https://patch.msgid.link/6b9347d5c1a0b364e88d900b29a616c3f8e5b1ca.1723483073.git.lucien.xin@gmail.comSigned-off-by:
-
Erwan Velu authored
Commit 2acda577 ("net/mlx5e: Improve remote NUMA preferences used for the IRQ affinity hints") removed the usage of cpumask_local_spread(). The issue explained in this commit was fixed by commit 406d394a ("cpumask: improve on cpumask_local_spread() locality"). Since this commit, mlx5_cpumask_default_spread() is having the same behavior as cpumask_local_spread(). This commit is about : - removing the specific logic and use cpumask_local_spread() instead - passing mlx5_core_dev as argument to more flexibility mlx5_cpumask_default_spread() is kept as it could be useful for some future specific quirks. Signed-off-by:
Erwan Velu <e.velu@criteo.com> Acked-by:
Yury Norov <yury.norov@gmail.com> Reviewed-by:
Tariq Toukan <tariqt@nvidia.com> Link: https://patch.msgid.link/20240812082244.22810-1-e.velu@criteo.comSigned-off-by:
-
Jakub Kicinski authored
Kuniyuki Iwashima says: ==================== ip: Random cleanup for devinet.c patch 1 ~ 3 remove defensive !ifa->ifa_dev tests. patch 4 & 5 deduplicate common code. ==================== Link: https://patch.msgid.link/20240809235406.50187-1-kuniyu@amazon.comSigned-off-by:
-
Kuniyuki Iwashima authored
INFINITY_LIFE_TIME is the common value used in IPv4 and IPv6 but defined in both .c files. Also, 0xffffffff used in addrconf_timeout_fixup() is INFINITY_LIFE_TIME. Let's move INFINITY_LIFE_TIME's definition to addrconf.h Signed-off-by:
Kuniyuki Iwashima <kuniyu@amazon.com> Link: https://patch.msgid.link/20240809235406.50187-6-kuniyu@amazon.comSigned-off-by:
-
Kuniyuki Iwashima authored
Whenever ifa is allocated, we call INIT_HLIST_NODE(&ifa->hash). Let's move it to inet_alloc_ifa(). Signed-off-by:
-
Kuniyuki Iwashima authored
Now, ifa_dev is only set in inet_alloc_ifa() and never NULL after ifa gets visible. Let's remove the unneeded NULL check for ifa->ifa_dev. Signed-off-by:
-
Kuniyuki Iwashima authored
When a new IPv4 address is assigned via ioctl(SIOCSIFADDR), inet_set_ifa() sets ifa->ifa_dev if it's different from in_dev passed as an argument. In this case, ifa is always a newly allocated object, and ifa->ifa_dev is NULL. inet_set_ifa() can be called for an existing reused ifa, then, this check is always false. Let's set ifa_dev in inet_alloc_ifa() and remove the check in inet_set_ifa(). Now, inet_alloc_ifa() is symmetric with inet_rcu_free_ifa(). Signed-off-by:
-
Kuniyuki Iwashima authored
dev->ip_ptr could be NULL if we set an invalid MTU. Even then, if we issue ioctl(SIOCSIFADDR) for a new IPv4 address, devinet_ioctl() allocates struct in_ifaddr and fails later in inet_set_ifa() because in_dev is NULL. Let's move the check earlier. Signed-off-by:
-
Pieter Van Trappen authored
Increase max_mtu from 1500 to 1518 bytes when not configured for jumbo frames. Use 1536 as a starting point as documented in macb.h for oversized (big) frames, which is the configuration applied in case jumbo frames capability is not configured; ref. macb_main.c. Signed-off-by:
Pieter Van Trappen <pieter.van.trappen@cern.ch> Link: https://patch.msgid.link/20240812090657.583821-1-vtpieter@gmail.comSigned-off-by:
-
Abhash Jha authored
The word 'expected' was spelled as 'exepcted'. Fixed the typo in this patch. Signed-off-by:
Abhash Jha <abhashkumarjha123@gmail.com> Reviewed-by:
Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20240814173121.33590-1-abhashkumarjha123@gmail.comSigned-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski authored
Cross-merge networking fixes after downstream PR. Conflicts: Documentation/devicetree/bindings/net/fsl,qoriq-mc-dpmac.yaml c25504a0 ("dt-bindings: net: fsl,qoriq-mc-dpmac: add missed property phys") be034ee6 ("dt-bindings: net: fsl,qoriq-mc-dpmac: using unevaluatedProperties") https://lore.kernel.org/20240815110934.56ae623a@canb.auug.org.au drivers/net/dsa/vitesse-vsc73xx-core.c 5b9eebc2 ("net: dsa: vsc73xx: pass value in phy_write operation") fa63c643 ("net: dsa: vsc73xx: check busy flag in MDIO operations") 2524d6c2 ("net: dsa: vsc73xx: use defined values in phy operations") https://lore.kernel.org/20240813104039.429b9fe6@canb.auug.org.au Resolve by using FIELD_PREP(), Stephen's resolution is simpler. Adjacent changes: net/vmw_vsock/af_vsock.c 69139d29 ("vsock: fix recursive ->recvmsg calls") 744500d8 ("vsock: add support for SIOCOUTQ ioctl") Link: https://patch.msgid.link/20240815141149.33862-1-pabeni@redhat.comSigned-off-by:
-
- 15 Aug, 2024 23 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netLinus Torvalds authored
Pull networking fixes from Paolo Abeni: "Including fixes from wireless and netfilter Current release - regressions: - udp: fall back to software USO if IPv6 extension headers are present - wifi: iwlwifi: correctly lookup DMA address in SG table Current release - new code bugs: - eth: mlx5e: fix queue stats access to non-existing channels splat Previous releases - regressions: - eth: mlx5e: take state lock during tx timeout reporter - eth: mlxbf_gige: disable RX filters until RX path initialized - eth: igc: fix reset adapter logics when tx mode change Previous releases - always broken: - tcp: update window clamping condition - netfilter: - nf_queue: drop packets with cloned unconfirmed conntracks - nf_tables: Add locking for NFT_MSG_GETOBJ_RESET requests - vsock: fix recursive ->recvmsg calls - dsa: vsc73xx: fix MDIO bus access and PHY opera - eth: gtp: pull network headers in gtp_dev_xmit() - eth: igc: fix packet still tx after gate close by reducing i226 MAC retry buffer - eth: mana: fix RX buf alloc_size alignment and atomic op panic - eth: hns3: fix a deadlock problem when config TC during resetting" * tag 'net-6.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (58 commits) net: hns3: use correct release function during uninitialization net: hns3: void array out of bound when loop tnl_num net: hns3: fix a deadlock problem when config TC during resetting net: hns3: use the user's cfg after reset net: hns3: fix wrong use of semaphore up selftests: net: lib: kill PIDs before del netns pse-core: Conditionally set current limit during PI regulator registration net: thunder_bgx: Fix netdev structure allocation net: ethtool: Allow write mechanism of LPL and both LPL and EPL vsock: fix recursive ->recvmsg calls selftest: af_unix: Fix kselftest compilation warnings netfilter: nf_tables: Add locking for NFT_MSG_GETOBJ_RESET requests netfilter: nf_tables: Introduce nf_tables_getobj_single netfilter: nf_tables: Audit log dump reset after the fact selftests: netfilter: add test for br_netfilter+conntrack+queue combination netfilter: nf_queue: drop packets with cloned unconfirmed conntracks netfilter: flowtable: initialise extack before use netfilter: nfnetlink: Initialise extack before use in ACKs netfilter: allow ipv6 fragments to arrive on different devices tcp: Update window clamping condition ... -
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-mediaLinus Torvalds authored
Pull media fixes from Mauro Carvalho Chehab: "Two regression fixes: - fix atomisp support for ISP2400 - fix dvb-usb regression for TeVii s480 dual DVB-S2 S660 board" * tag 'media/v6.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: media: atomisp: Fix streaming no longer working on BYT / ISP2400 devices media: Revert "media: dvb-usb: Fix unexpected infinite loop in dvb_usb_read_remote_control()"
-
git://git.kernel.org/pub/scm/linux/kernel/git/libata/linuxLinus Torvalds authored
Pull ata fix from Niklas Cassel: - Revert a recent change to sense data generation. Sense data can be in either fixed format or descriptor format. The D_SENSE bit in the Control mode page controls which format to generate. All places but one respected the D_SENSE bit. The recent change fixed the one place that didn't respect the D_SENSE bit. However, it turns out that hdparm, hddtemp and udisks (incorrectly) assumes sense data in descriptor format. Therefore, even while the change was technically correct, revert it, since even if these user space programs are fixed to (correctly) look at the format type before parsing the data, older versions of these tools will be around roughly forever. * tag 'ata-6.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/libata/linux: Revert "ata: libata-scsi: Honor the D_SENSE bit for CK_COND=1 and no error"
-
git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nfPaolo Abeni authored
Pablo Neira Ayuso says: ==================== Netfilter fixes for net The following patchset contains Netfilter fixes for net: 1) Ignores ifindex for types other than mcast/linklocal in ipv6 frag reasm, from Tom Hughes. 2) Initialize extack for begin/end netlink message marker in batch, from Donald Hunter. 3) Initialize extack for flowtable offload support, also from Donald. 4) Dropped packets with cloned unconfirmed conntracks in nfqueue, later it should be possible to explore lookup after reinject but Florian prefers this approach at this stage. From Florian Westphal. 5) Add selftest for cloned unconfirmed conntracks in nfqueue for previous update. 6) Audit after filling netlink header successfully in object dump, from Phil Sutter. 7-8) Fix concurrent dump and reset which could result in underflow counter / quota objects. netfilter pull request 24-08-15 * tag 'nf-24-08-15' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf: netfilter: nf_tables: Add locking for NFT_MSG_GETOBJ_RESET requests netfilter: nf_tables: Introduce nf_tables_getobj_single netfilter: nf_tables: Audit log dump reset after the fact selftests: netfilter: add test for br_netfilter+conntrack+queue combination netfilter: nf_queue: drop packets with cloned unconfirmed conntracks netfilter: flowtable: initialise extack before use netfilter: nfnetlink: Initialise extack before use in ACKs netfilter: allow ipv6 fragments to arrive on different devices ==================== Link: https://patch.msgid.link/20240814222042.150590-1-pablo@netfilter.orgSigned-off-by:Paolo Abeni <pabeni@redhat.com>
-
Paolo Abeni authored
Jijie Shao says: ==================== There are some bugfix for the HNS3 ethernet driver ==================== Link: https://patch.msgid.link/20240813141024.1707252-1-shaojijie@huawei.comSigned-off-by:
-
Peiyang Wang authored
pci_request_regions is called to apply for PCI I/O and memory resources when the driver is initialized, Therefore, when the driver is uninstalled, pci_release_regions should be used to release PCI I/O and memory resources instead of pci_release_mem_regions is used to release memory reasouces only. Signed-off-by:
Peiyang Wang <wangpeiyang1@huawei.com> Signed-off-by:
Jijie Shao <shaojijie@huawei.com> Signed-off-by:
-
Peiyang Wang authored
When query reg inf of SSU, it loops tnl_num times. However, tnl_num comes from hardware and the length of array is a fixed value. To void array out of bound, make sure the loop time is not greater than the length of array Signed-off-by:
-
Jie Wang authored
When config TC during the reset process, may cause a deadlock, the flow is as below: pf reset start │ ▼ ...... setup tc │ │ ▼ ▼ DOWN: napi_disable() napi_disable()(skip) │ │ │ ▼ ▼ ...... ...... │ │ ▼ │ napi_enable() │ ▼ UINIT: netif_napi_del() │ ▼ ...... │ ▼ INIT: netif_napi_add() │ ▼ ...... global reset start │ │ ▼ ▼ UP: napi_enable()(skip) ...... │ │ ▼ ▼ ...... napi_disable() In reset process, the driver will DOWN the port and then UINIT, in this case, the setup tc process will UP the port before UINIT, so cause the problem. Adds a DOWN process in UINIT to fix it. Fixes: bb6b94a8 ("net: hns3: Add reset interface implementation in client") Signed-off-by:Jie Wang <wangjie125@huawei.com> Signed-off-by:
-
Peiyang Wang authored
Consider the followed case that the user change speed and reset the net interface. Before the hw change speed successfully, the driver get old old speed from hw by timer task. After reset, the previous speed is config to hw. As a result, the new speed is configed successfully but lost after PF reset. The followed pictured shows more dirrectly. +------+ +----+ +----+ | USER | | PF | | HW | +---+--+ +-+--+ +-+--+ | ethtool -s 100G | | +------------------>| set speed 100G | | +--------------------->| | | set successfully | | |<---------------------+---+ | |query cfg (timer task)| | | +--------------------->| | handle speed | | return 200G | | changing event | ethtool --reset |<---------------------+ | (100G) +------------------>| cfg previous speed |<--+ | | after reset (200G) | | +--------------------->| | | +---+ | |query cfg (timer task)| | | +--------------------->| | handle speed | | return 100G | | changing event | |<---------------------+ | (200G) | | |<--+ | |query cfg (timer task)| | +--------------------->| | | return 200G | | |<---------------------+ | | | v v v This patch save new speed if hw change speed successfully, which will be used after reset successfully. Fixes: 2d03eacc ("net: hns3: Only update mac configuation when necessary") Signed-off-by: -
Jie Wang authored
Currently, if hns3 PF or VF FLR reset failed after five times retry, the reset done process will directly release the semaphore which has already released in hclge_reset_prepare_general. This will cause down operation fail. So this patch fixes it by adding reset state judgement. The up operation is only called after successful PF FLR reset. Fixes: 8627bded ("net: hns3: refactor the precedure of PF FLR") Fixes: f28368bb ("net: hns3: refactor the procedure of VF FLR") Signed-off-by:
-
Matthieu Baerts (NGI0) authored
When deleting netns, it is possible to still have some tasks running, e.g. background tasks like tcpdump running in the background, not stopped because the test has been interrupted. Before deleting the netns, it is then safer to kill all attached PIDs, if any. That should reduce some noises after the end of some tests, and help with the debugging of some issues. That's why this modification is seen as a "fix". Fixes: 25ae948b ("selftests/net: add lib.sh") Acked-by:
Mat Martineau <martineau@kernel.org> Signed-off-by:
Matthieu Baerts (NGI0) <matttbe@kernel.org> Acked-by:
Hangbin Liu <liuhangbin@gmail.com> Link: https://patch.msgid.link/20240813-upstream-net-20240813-selftests-net-lib-kill-v1-1-27b689b248b8@kernel.orgSigned-off-by:
-
Oleksij Rempel authored
Fix an issue where `devm_regulator_register()` would fail for PSE controllers that do not support current limit control, such as simple GPIO-based controllers like the podl-pse-regulator. The `REGULATOR_CHANGE_CURRENT` flag and `max_uA` constraint are now conditionally set only if the `pi_set_current_limit` operation is supported. This change prevents the regulator registration routine from attempting to call `pse_pi_set_current_limit()`, which would return `-EOPNOTSUPP` and cause the registration to fail. Fixes: 4a83abce ("net: pse-pd: Add new power limit get and set c33 features") Signed-off-by:
Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by:
Kory Maincent <kory.maincent@bootlin.com> Tested-by:
Kyle Swenson <kyle.swenson@est.tech> Link: https://patch.msgid.link/20240813073719.2304633-1-o.rempel@pengutronix.deSigned-off-by:
-
Marc Zyngier authored
Commit 94833add ("net: thunderx: Unembed netdev structure") had a go at dynamically allocating the netdev structures for the thunderx_bgx driver. This change results in my ThunderX box catching fire (to be fair, it is what it does best). The issues with this change are that: - bgx_lmac_enable() is called *after* bgx_acpi_register_phy() and bgx_init_of_phy(), both expecting netdev to be a valid pointer. - bgx_init_of_phy() populates the MAC addresses for *all* LMACs attached to a given BGX instance, and thus needs netdev for each of them to have been allocated. There is a few things to be said about how the driver mixes LMAC and BGX states which leads to this sorry state, but that's beside the point. To address this, go back to a situation where all netdev structures are allocated before the driver starts relying on them, and move the freeing of these structures to driver removal. Someone brave enough can always go and restructure the driver if they want. Fixes: 94833add ("net: thunderx: Unembed netdev structure") Signed-off-by:
Marc Zyngier <maz@kernel.org> Cc: Breno Leitao <leitao@debian.org> Cc: Sunil Goutham <sgoutham@marvell.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Eric Dumazet <edumazet@google.com> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Paolo Abeni <pabeni@redhat.com> Reviewed-by:
Breno Leitao <leitao@debian.org> Link: https://patch.msgid.link/20240812141322.1742918-1-maz@kernel.orgSigned-off-by:
-
Danielle Ratson authored
CMIS 5.2 standard section 9.4.2 defines four types of firmware update supported mechanism: None, only LPL, only EPL, both LPL and EPL. Currently, only LPL (Local Payload) type of write firmware block is supported. However, if the module supports both LPL and EPL the flashing process wrongly fails for no supporting LPL. Fix that, by allowing the write mechanism to be LPL or both LPL and EPL. Fixes: c4f78134 ("ethtool: cmis_fw_update: add a layer for supporting firmware update using CDB") Reported-by:
Vladyslav Mykhaliuk <vmykhaliuk@nvidia.com> Signed-off-by:
Danielle Ratson <danieller@nvidia.com> Reviewed-by:
Petr Machata <petrm@nvidia.com> Link: https://patch.msgid.link/20240812140824.3718826-1-danieller@nvidia.comSigned-off-by:
-
Cong Wang authored
After a vsock socket has been added to a BPF sockmap, its prot->recvmsg has been replaced with vsock_bpf_recvmsg(). Thus the following recursiion could happen: vsock_bpf_recvmsg() -> __vsock_recvmsg() -> vsock_connectible_recvmsg() -> prot->recvmsg() -> vsock_bpf_recvmsg() again We need to fix it by calling the original ->recvmsg() without any BPF sockmap logic in __vsock_recvmsg(). Fixes: 634f1a71 ("vsock: support sockmap") Reported-by: syzbot+bdb4bd87b5e22058e2a4@syzkaller.appspotmail.com Tested-by: syzbot+bdb4bd87b5e22058e2a4@syzkaller.appspotmail.com Cc: Bobby Eshleman <bobby.eshleman@bytedance.com> Cc: Michael S. Tsirkin <mst@redhat.com> Cc: Stefano Garzarella <sgarzare@redhat.com> Signed-off-by:Cong Wang <cong.wang@bytedance.com> Acked-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wirelessJakub Kicinski authored
Kalle Valo says: ==================== wireless fixes for v6.11 We have few fixes to drivers. The most important here is a fix for iwlwifi which caused major slowdowns for several users. * tag 'wireless-2024-08-14' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless: wifi: iwlwifi: correctly lookup DMA address in SG table wifi: mt76: mt7921: fix NULL pointer access in mt7921_ipv6_addr_change wifi: brcmfmac: cfg80211: Handle SSID based pmksa deletion wifi: rtlwifi: rtl8192du: Initialise value32 in _rtl92du_init_queue_reserved_page wifi: ath12k: use 128 bytes aligned iova in transmit path for WCN7850 ==================== Link: https://patch.msgid.link/20240814171606.E14A0C116B1@smtp.kernel.orgSigned-off-by:
-
Abhinav Jain authored
Change expected_buf from (const void *) to (const char *) in function __recvpair(). This change fixes the below warnings during test compilation: ``` In file included from msg_oob.c:14: msg_oob.c: In function ‘__recvpair’: ../../kselftest_harness.h:106:40: warning: format ‘%s’ expects argument of type ‘char *’,but argument 6 has type ‘const void *’ [-Wformat=] ../../kselftest_harness.h:101:17: note: in expansion of macro ‘__TH_LOG’ msg_oob.c:235:17: note: in expansion of macro ‘TH_LOG’ ../../kselftest_harness.h:106:40: warning: format ‘%s’ expects argument of type ‘char *’,but argument 6 has type ‘const void *’ [-Wformat=] ../../kselftest_harness.h:101:17: note: in expansion of macro ‘__TH_LOG’ msg_oob.c:259:25: note: in expansion of macro ‘TH_LOG’ ``` Fixes: d098d772 ("selftest: af_unix: Add msg_oob.c.") Signed-off-by:
Abhinav Jain <jain.abhinav177@gmail.com> Reviewed-by:
-
Jakub Kicinski authored
Gustavo A. R. Silva says: ==================== UAPI: net/sched - cxgb4: Fix -Wflex-array-member-not-at-end warning Small patch series aimed at fixing a -Wflex-array-member-not-at-end warning by creating a new tagged struct within a flexible structure. We then use this new struct type to fix a problematic middle-flex-array declaration in a composite struct. ==================== Link: https://patch.msgid.link/cover.1723586870.git.gustavoars@kernel.orgSigned-off-by:
-
Gustavo A. R. Silva authored
-Wflex-array-member-not-at-end was introduced in GCC-14, and we are getting ready to enable it, globally. Change the type of the middle struct member currently causing trouble from `struct tc_u32_sel` to `struct tc_u32_sel_hdr`. Fix the following warning: drivers/net/ethernet/chelsio/cxgb4/cxgb4_tc_u32_parse.h:245:27: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end] Signed-off-by:
Gustavo A. R. Silva <gustavoars@kernel.org> Link: https://patch.msgid.link/97388e8a7990975aa56cf0ada211764c735c3432.1723586870.git.gustavoars@kernel.orgSigned-off-by:
-
Gustavo A. R. Silva authored
Use the `__struct_group()` helper to create a new tagged `struct tc_u32_sel_hdr`. This structure groups together all the members of the flexible `struct tc_u32_sel` except the flexible array. As a result, the array is effectively separated from the rest of the members without modifying the memory layout of the flexible structure. This new tagged struct will be used to fix problematic declarations of middle-flex-arrays in composite structs[1]. [1] https://git.kernel.org/linus/d88cabfd9abcSigned-off-by:
-
Jakub Kicinski authored
Simon Horman says: ==================== bnxt_en: address string truncation This series addresses several string truncation issues that are flagged by gcc-14. I do not have any reason to believe these are bugs, so I am targeting this at net-next and have not provided Fixes tags. v1: https://lore.kernel.org/r/20240705-bnxt-str-v1-0-bafc769ed89e@kernel.org ==================== Link: https://patch.msgid.link/20240813-bnxt-str-v2-0-872050a157e7@kernel.orgSigned-off-by:
-
Simon Horman authored
Although it seems unlikely in practice - there would need to be rx ring indexes greater than 10^10 - it is theoretically possible for the filename of per rx ring debugfs files to be truncated. This is because although a 16 byte buffer is provided, the length of the filename is restricted to 10 bytes. Remove this restriction and allow the entire buffer to be used. Also reduce the buffer to 12 bytes, which is sufficient. Given that the range of rx ring indexes likely much smaller than the maximum range of a 32-bit signed integer, a smaller buffer could be used, with some further changes. But this change seems simple, robust, and has minimal stack overhead. Flagged by gcc-14: .../bnxt_debugfs.c: In function 'bnxt_debug_dev_init': drivers/net/ethernet/broadcom/bnxt/bnxt_debugfs.c:69:30: warning: '%d' directive output may be truncated writing between 1 and 11 bytes into a region of size 10 [-Wformat-truncation=] 69 | snprintf(qname, 10, "%d", ring_idx); | ^~ In function 'debugfs_dim_ring_init', inlined from 'bnxt_debug_dev_init' at .../bnxt_debugfs.c:87:4: .../bnxt_debugfs.c:69:29: note: directive argument in the range [-2147483643, 2147483646] 69 | snprintf(qname, 10, "%d", ring_idx); | ^~~~ .../bnxt_debugfs.c:69:9: note: 'snprintf' output between 2 and 12 bytes into a destination of size 10 69 | snprintf(qname, 10, "%d", ring_idx); | ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Compile tested only Signed-off-by:Michael Chan <michael.chan@broadcom.com> Link: https://patch.msgid.link/20240813-bnxt-str-v2-2-872050a157e7@kernel.orgSigned-off-by:
-
Simon Horman authored
This corrects an out-by-one error in the maximum length of the package version string. The size argument of snprintf includes space for the trailing '\0' byte, so there is no need to allow extra space for it by reducing the value of the size argument by 1. Found by inspection. Compile tested only. Signed-off-by:
-
