Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Just do it once.

Pointed out by Al Viro.
Signed-off-by: David S. Miller <davem@davemloft.net>

This is complicated a little because compat_audit.c wants to see only
the 32bit syscall numbers, but is being built in a 64bit compile.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

We use clock cycle counter, adjusted to HZ.

This can be extended to sun4v based processors as well, as they
also have a proper overflow interrupt facility for the performance
counters.
Signed-off-by: David S. Miller <davem@davemloft.net>

It writes the %pic register, keeping mind of processor bugs.

Implement reset_pic() in terms of it.
Signed-off-by: David S. Miller <davem@davemloft.net>

In these instructions we load the new thread register, switch
the register window, and setup the new frame pointer.

All of these must appear atomic, and things will explode if
we take a PIL=15 NMI interrupt in the middle of this sequence.
Signed-off-by: David S. Miller <davem@davemloft.net>

We don't want the rtrap path to try and run softirqs or
anything like that when returning from a PIL==15 NMI.
Signed-off-by: David S. Miller <davem@davemloft.net>

So that we can profile code even in a local_irq_disable() section,
only write 14 (instead of 15) into the %pil register to disable IRQs.

This allows PIL level 15 to serve as a pseudo NMI.
Signed-off-by: David S. Miller <davem@davemloft.net>

Stephen Rothwell pointed out that pcmcia can't be enabled on sparc64.

There is an empty non-prompt PCMCIA explicit entry in
arch/sparc/Kconfig but that doesn't do anything.

32-bit sparc needs a small hack to make this work, since it doesn't
use the generic IRQ layer yes.  We have to provide a dummy definition
of probe_irq_mask(), since this is used by the yenta socket driver.
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: David S. Miller <davem@davemloft.net>

Add a sysctl to tweak the RSS limit used to decide when to grow
the TSB for an address space.

In order to avoid expensive divides and multiplies only simply
positive and negative powers of two are supported.

The function computed takes the number of TSB translations that will
fit at one time in the TSB of a given size, and either adds or
subtracts a percentage of entries.  This final value is the
RSS limit.

See tsb_size_to_rss_limit().
Signed-off-by: David S. Miller <davem@davemloft.net>

- move all sparc64/mm/ files to arch/sparc/mm/
- commonly named files are named _64.c
- add files to sparc/mm/Makefile preserving link order
- delete now unused sparc64/mm/Makefile
- sparc64 now finds mm/ in sparc
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

- rename files where sparc64 has similar files to _32.c
- Restructure Makefile
- Sneak in -Werror as we have for sparc64
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

A simple:

   diff arch/sparc64/oprofile/init.c arch/sparc/oprofile/init.c
   diff arch/sparc64/oprofile/Makefile arch/sparc/oprofile/Makefile

revealed that the directories were equal.
So let sparc64 point to the sparc version and drop the sparc64 oprofile dir
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move relavent files to sparc/math-emu and
adjust path/include accordingly.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add _32 to filenames to make them 32 bit unique
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

- Drop unused assignment from Makefile
- Replace EXTRA_CFLAGS with ccflags-y
- Delete unused file
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

BITS will be used to simplify unified Makefiles
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge all of sparc64 Kconfig to sparc Kconfig.
The merge was checked by:
- visual inspection in menuconfig
- result of allnoconfig, allmodconfig, allyesconfig was checked before and after
- result of a number of randconfig was checked before and after

scripts/diffconfig was used to check if the config differed before and after

The validity of the test was checked by on purpose introducing
a few bugs - and they were all caught by first run.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

To align with sparc64 add a "Bus options" menu
This has the additiona advantage that all
bus options are kept together
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is what we use in sparc64 - make sparc equal
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

We already has the proper definition in place in param.h.
So use the common Kconfig.hz file
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

We have it in drivers/char/Kconfig
There is no need to ask twice
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

moved a few config entries inside a menu so we
do not clutter the first screen up with a lot of detailed
config options.
The structure now remotely resemble the structure for i386
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Mode declaration of SPARC up in the top
to match the structure of sparc64 Kconfig
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Let sparc and sparc64 use the same Kconfig.debug
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The kernel always executes in the TSO memory model now,
so none of this stuff is necessary any more.

With helpful feedback from Nick Piggin.
Signed-off-by: David S. Miller <davem@davemloft.net>

The fact of the matter is, all UltraSPARC-III and later chips only
implement TSO.  They don't implement PSO and RMO memory models at all.

Only the Ultra-I and Ultra-II family chips implement RMO and they are
only helped marginally by using this setting when executing kernel
code.

The big plus to doing this is that we can eliminate all of the non-Sync
memory barriers in the kernel except for the ones used in the optimized
memcpy/memset code (these use block load and store operations which
have their own memory ordering rules).
Signed-off-by: David S. Miller <davem@davemloft.net>

It only uses of_platform_bus_type.
Signed-off-by: David S. Miller <davem@davemloft.net>

Use common functions instead of inlining and duplicating logic
over and over to handle the SBUS vs. EBUS cases.

Before:

   text	   data	    bss	    dec	    hex	filename
    715	    568	     16	   1299	    513	arch/sparc64/kernel/auxio.o

After:

   text	   data	    bss	    dec	    hex	filename
    631	    568	     16	   1215	    4bf	arch/sparc64/kernel/auxio.o
Signed-off-by: David S. Miller <davem@davemloft.net>

Copy the FPU state to the task's thread_info->fpregs for the VIS emulation
functions to access.
Signed-off-by: Hong H. Pham <hong.pham@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes some bugs in VIS emulation that cause the GCC test
failure

FAIL: gcc.target/sparc/pdist-3.c execution test

for both 32-bit and 64-bit testing on hardware lacking these
instructions.  The emulation code for the pdist instruction uses
RS1(insn) for both source registers rs1 and rs2, which is obviously
wrong and leads to the instruction doing nothing (the observed
problem), and further inspection of the code shows that RS1 uses a
shift of 24 and RD a shift of 25, which clearly cannot both be right;
examining SPARC documentation indicates the correct shift for RS1 is
14.

This patch fixes the bug if single-stepping over the affected
instruction in the debugger, but not if the testcase is run
standalone.  For that, Wind River has another patch I hope they will
send as a followup to this patch submission.
Signed-off-by: Joseph Myers <joseph@codesourcery.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
  block: fix setting of max_segment_size and seg_boundary mask
  block: internal dequeue shouldn't start timer
  block: set disk->node_id before it's being used
  When block layer fails to map iov, it calls bio_unmap_user to undo

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
  powerpc/83xx: Fix MCU support merge issue in mpc8349emitx.dts
  powerpc: Fix dma_map_sg() cache flushing on non coherent platforms

* 'for-2.6.28' of git://linux-nfs.org/~bfields/linux:
  NLM: client-side nlm_lookup_host() should avoid matching on srcaddr
  nfsd: use of unitialized list head on error exit in nfs4recover.c
  Add a reference to sunrpc in svc_addsock
  nfsd: clean up grace period on early exit

The code used '&= 0x00002000' when it tried to set the TCO_EN bit, which
obviously didn't set that bit at all, but instead just reset all the
other bits in the SMI_EN register.

This bug seemingly caused various random behavior, with Frans Pop
reporting that X.org just silently hung at startup and Rafael Wysocki
reports the fan spinning with full speed.

See
	http://lkml.org/lkml/2008/12/3/178
	http://bugzilla.kernel.org/show_bug.cgi?id=12162

The problem seems to have been triggered by "[WATCHDOG] iTCO_wdt :
problem with rebooting on new ICH9 based motherboards" (commit
7cd5b08b), but the bogus code existed
before that too (in the "supermicro_old_pre_stop()" function), it just
apparently never showed up due to different logic.

In that commit the broken code got moved around and now gets executed
much more.
Reported-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Frans Pop <elendil@planet.nl>
Cc: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

bitops_64.h includes the generic one; pretty sure 32 should too.

(Found by using __fls in generic code and breaking sparc defconfig build:
 thanks Stephen and linux-next!)
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Just found the merge issue in 44274698
("powerpc/83xx: Add support for MCU microcontroller in .dts files"):
the commit adds the MCU controller node into the DMA node, which is
wrong because the MCU sits on the I2C bus. Fix this by moving the MCU
node into the I2C controller node.

The original patch[1] was OK though. ;-)
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Fix setting of max_segment_size and seg_boundary mask for stacked md/dm
devices.

When stacking devices (LVM over MD over SCSI) some of the request queue
parameters are not set up correctly in some cases by default, namely
max_segment_size and and seg_boundary mask.

If you create MD device over SCSI, these attributes are zeroed.

Problem become when there is over this mapping next device-mapper mapping
- queue attributes are set in DM this way:

request_queue   max_segment_size  seg_boundary_mask
SCSI                65536             0xffffffff
MD RAID1                0                      0
LVM                 65536                 -1 (64bit)

Unfortunately bio_add_page (resp.  bio_phys_segments) calculates number of
physical segments according to these parameters.

During the generic_make_request() is segment cout recalculated and can
increase bio->bi_phys_segments count over the allowed limit.  (After
bio_clone() in stack operation.)

Thi is specially problem in CCISS driver, where it produce OOPS here

    BUG_ON(creq->nr_phys_segments > MAXSGENTRIES);

(MAXSEGENTRIES is 31 by default.)

Sometimes even this command is enough to cause oops:

  dd iflag=direct if=/dev/<vg>/<lv> of=/dev/null bs=128000 count=10

This command generates bios with 250 sectors, allocated in 32 4k-pages
(last page uses only 1024 bytes).

For LVM layer, it allocates bio with 31 segments (still OK for CCISS),
unfortunatelly on lower layer it is recalculated to 32 segments and this
violates CCISS restriction and triggers BUG_ON().

The patch tries to fix it by:

 * initializing attributes above in queue request constructor
   blk_queue_make_request()

 * make sure that blk_queue_stack_limits() inherits setting

 (DM uses its own function to set the limits because it
 blk_queue_stack_limits() was introduced later.  It should probably switch
 to use generic stack limit function too.)

 * sets the default seg_boundary value in one place (blkdev.h)

 * use this mask as default in DM (instead of -1, which differs in 64bit)

Bugs related to this:
https://bugzilla.redhat.com/show_bug.cgi?id=471639
http://bugzilla.kernel.org/show_bug.cgi?id=8672Signed-off-by: Milan Broz <mbroz@redhat.com>
Reviewed-by: Alasdair G Kergon <agk@redhat.com>
Cc: Neil Brown <neilb@suse.de>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>