* use irq_chip
* use handle_level_irq
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The patch adds ifdefs around per cpu definitions. Otherwise, if
not all cpu types are selected, the kernel does not link.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

On ixp23xx, it was thought to be necessary to disable coherency to work
around certain silicon errata.  This turns out not to be the case --
none of the documented errata workarounds require disabling coherency,
and disabling coherency does not work around any existing errata.

Furthermore, all ixp23xx models do support coherency, so we should just
unconditionally enable coherency for all ixp23xx.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The struct resource 'end' field is inclusive, the iop13xx flash
setup code got this wrong.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The phys_io/io_pg_offst machine record variables were being set
to bogus values, causing problems when enabling DEBUG_LL.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Add HWCAP_CRUNCH so that the dynamic linker knows whether it can
use Crunch-optimised libraries or not.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Fix up the CONFIG_PM mixups in arch/arm/mach-s3c2410/Kconfig
causing CONFIG_S3C2410_PM and CONFIG_PM_H1940 to get enabled
permanently.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Move adjust_cr() into arch/arm/mm/mmu.c, and move irqflags.h to
a more appropriate place in the header file.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Clean the includes in arch/arm/mach-s3c2410/s3c2440.c
and arch/arm/mach-s3c2410/s3c2442.c which should have
been pruned when these where split and updated.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Remove old changelog entries in arch/arm/mach-s3c2410
which should be available from the version control
system.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Change the include/asm-arm/arch-s3c2410/regs-serial.h
platform data to use the prorper type (upf_t) for the
uart_flags.

Fix all the other parts of arch/arm/mach-s3c2410 to
include <linux/serial_core.h> and all other uses of
the include file.

mach-rx3715.c:101:18: warning: incorrect type in initializer (different base types)
mach-rx3715.c:101:18:    expected unsigned long [unsigned] uart_flags
mach-rx3715.c:101:18:    got restricted unsigned int [usertype] [force] <noident>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Remove warning from s3c2410_pm_resume() not being
declared by making it static.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Fix the following sparse errors in arch/arm/mach-s3c2410
by fixing the include paths and making un-exported items
static.

s3c2410-clock.c:206:12: warning: symbol 's3c2410_baseclk_add' was not declared. Should it be static?
s3c2412-clock.c:559:17: warning: symbol 'clks_src' was not declared. Should it be static?
s3c2412-clock.c:622:12: warning: symbol 'clks' was not declared. Should it be static?
s3c2412-clock.c:630:12: warning: symbol 's3c2412_baseclk_add' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Remove old (and non-shared) VA addresses from the mappings
in arch/arm/mach-s3c2410/map.h and anywhere they are being
mapped in arch/arm/mach-s3c2410
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Fix sparse errors in arch/arm/mach-s3c2410/s3c2442-clock.c

warning: symbol 'clk_h' shadows an earlier one
warning: symbol 'clk_p' shadows an earlier one
warning: symbol 'clk_upll' shadows an earlier one
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Fix the sparse errors in arch/arm/mach-s3c2410/s3c2440-clock.c

warning: symbol 'clk_h' shadows an earlier one
warning: symbol 'clk_p' shadows an earlier one
warning: symbol 'clk_upll' shadows an earlier one
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Fix address-space conversion errors from passing addresses
generated from include/asm-arm/arch-s3c2410/map.h by adding
an __force argument to the `void __iomem *` for all the
virtual addresses.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Fix address-space conversion errors from passing addresses
generated from include/asm-arm/arch-s3c2410/map.h by adding
an __force argument to the `void __iomem *` for all the
virtual addresses.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Fix the copyright messages in arch/arm/mach-s3c2410
to actually have `Copyright` in the line.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Fix copyright notices in include/asm-arm/arch-s3c2410
to actually have `Copyright` in the line. This patch
deals with all the core files.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Fix copyright notices in include/asm-arm/arch-s3c2410
to actually have `Copyright` in the line. This patch
deals with all the core files.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Thanks to Al Viro, here's fix to 2.6.20-rc1-git, so that collie
compiles, again. It was broken by INIT_WORK changes.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Fix pxafb compile failures when CONFIG_FB_PXA_PARAMETERS is enabled
after recent structure changes.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

We need to ensure that the area size is page aligned so that
remap_area_pte() doesn't increment the address past the end of
the desired area.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Add:
  sys_unshare
  sys_set_robust_list
  sys_get_robust_list
  sys_splice
  sys_arm_sync_file_range
  sys_tee
  sys_vmsplice
  sys_move_pages
  sys_getcpu

Special note about sys_arm_sync_file_range(), which is implemented as:

asmlinkage long sys_arm_sync_file_range(int fd, unsigned int flags,
                                        loff_t offset, loff_t nbytes)
{
        return sys_sync_file_range(fd, offset, nbytes, flags);
}

We can't export sys_sync_file_range() directly on ARM because the
argument list someone picked does not fit in the available registers.
Would be nice if... there was an arch maintainer review mechanism for
new syscalls before they hit the kernel.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  [PATCH] pata_via: Cable detect error
  [PATCH] Fix help text for CONFIG_ATA_PIIX
  [PATCH] initializer entry defined twice in pata_rz1000
  [PATCH] ata: fix platform_device_register_simple() error check
  [PATCH] ahci: do not mangle saved HOST_CAP while resetting controller
  [PATCH] libata: don't initialize sg in ata_exec_internal() if DMA_NONE (take #2)
  [libata] sata_svw: Disable ATAPI DMA on current boards (errata workaround)
  [libata] use kmap_atomic(KM_IRQ0) in SCSI simulator
  [PATCH] ata_piix: use piix_host_stop() in ich_pata_ops
  [PATCH] ata_piix: IDE mode SATA patch for Intel ICH9

On architectures where the atomicity of the bit operations is handled by
external means (ie a separate spinlock to protect concurrent accesses),
just doing a direct assignment on the workqueue data field (as done by
commit 4594bf15) can cause the
assignment to be lost due to lack of serialization with the bitops on
the same word.

So we need to serialize the assignment with the locks on those
architectures (notably older ARM chips, PA-RISC and sparc32).

So rather than using an "unsigned long", let's use "atomic_long_t",
which already has a safe assignment operation (atomic_long_set()) on
such architectures.

This requires that the atomic operations use the same atomicity locks as
the bit operations do, but that is largely the case anyway.  Sparc32
will probably need fixing.

Architectures (including modern ARM with LL/SC) that implement sane
atomic operations for SMP won't see any of this matter.

Cc: Russell King <rmk+lkml@arm.linux.org.uk>
Cc: David Howells <dhowells@redhat.com>
Cc: David Miller <davem@davemloft.com>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Linux Arch Maintainers <linux-arch@vger.kernel.org>
Cc: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Doug Chapman noticed that mincore() will doa "copy_to_user()" of the
result while holding the mmap semaphore for reading, which is a big
no-no.  While a recursive read-lock on a semaphore in the case of a page
fault happens to work, we don't actually allow them due to deadlock
schenarios with writers due to fairness issues.

Doug and Marcel sent in a patch to fix it, but I decided to just rewrite
the mess instead - not just fixing the locking problem, but making the
code smaller and (imho) much easier to understand.

Cc: Doug Chapman <dchapman@redhat.com>
Cc: Marcel Holtmann <holtmann@redhat.com>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

The UDMA66 VIA hardware has no controller side cable detect bits we can
use. This patch minimally fixes the problem by reporting unknown in this
case and using drive side detection.

The old drivers/ide code does some additional tricks but those aren't
appropriate now we are in -rc.

Without this update UDMA66 via controllers run slowly. They don't fail so
it's a borderline call whether this is -rc material or not.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

> Thanks for clarifying Bill, and sorry Alan. ata_piix does indeed work
> correctly. The help text is a bit confusing:
>
> config ATA_PIIX
>         tristate "Intel PIIX/ICH SATA support"
>         depends on PCI
>         help
>           This option enables support for ICH5/6/7/8 Serial ATA.
>           If PATA support was enabled previously, this enables
>           support for select Intel PIIX/ICH PATA host controllers.

New help text
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

This removes the extra definition of the .error_handler member
in the pata_rz1000 driver.
Signed-off-by: Ira W. Snyder <kernel@irasnyder.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

The return value of platform_device_register_simple() should be checked
by IS_ERR().

Cc: Jeff Garzik <jgarzik@pobox.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Do not mangle with HOST_CAP while resetting controller.  The code is
there for a historical reason.  The mangling breaks controller feature
detection and 0 PORTS_IMPL workaround code.

This problem was spotted by Manoj Kasichainula.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Manoj Kasichainula <manoj@io.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Calling sg_init_one() with NULL buf causes oops on certain
configurations.  Don't initialize sg in ata_exec_internal() if
DMA_NONE and make the function complain if @buf is NULL when dma_dir
isn't DMA_NONE.  While at it, fix comment.

The problem is discovered and initial patch was submitted by Arnd
Bergmann.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Current Broadcom/Serverworks SATA boards (including Apple K2 SATA)
have problems with ATAPI DMA, so it is disabled.  ATAPI PIO, ATA PIO,
and ATA DMA continue to work just fine.
Acked-by: Anantha Subramanyam <ananth@broadcom.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

We are inside spin_lock_irqsave().  quoth akpm's debug facility:

 [  231.948000] SCSI device sda: 195371568 512-byte hdwr sectors (100030 MB)
 [  232.232000] ata1.00: configured for UDMA/33
 [  232.404000] WARNING (1) at arch/i386/mm/highmem.c:47 kmap_atomic()
 [  232.404000]  [<c01162e6>] kmap_atomic+0xa9/0x1ab
 [  232.404000]  [<c0242c81>] ata_scsi_rbuf_get+0x1c/0x30
 [  232.404000]  [<c0242caf>] ata_scsi_rbuf_fill+0x1a/0x87
 [  232.404000]  [<c0243ab2>] ata_scsiop_mode_sense+0x0/0x309
 [  232.404000]  [<c01729d5>] end_bio_bh_io_sync+0x0/0x37
 [  232.404000]  [<c02311c6>] scsi_done+0x0/0x16
 [  232.404000]  [<c02311c6>] scsi_done+0x0/0x16
 [  232.404000]  [<c0242dcc>] ata_scsi_simulate+0xb0/0x13f
[...]
Signed-off-by: Jeff Garzik <jeff@garzik.org>

piix_init_one() allocates host private data which should be freed by
piix_host_stop().  ich_pata_ops wasn't converted to piix_host_stop()
while merging, leaking 4 bytes on driver detach.  Fix it.

This was spotted using Kmemleak by Catalin Marinas.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Catalin Marinas <catalin.marinas@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

This updated patch adds the Intel ICH9 IDE mode SATA controller DID's.
Signed-off-by: Jason Gaston <jason.d.gaston@intel.com>
Acked-by: Tejun Heo <htejun@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Nobody uses it, but it was still wrong.  Using the macro argument name
'work' meant that when we used 'work' as a member name, that would also
get replaced by the macro argument.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
  [S390] cio: css_register_subchannel race.
  [S390] Save prefix register for dump on panic
  [S390] Fix reboot hang
  [S390] Fix reboot hang on LPARs
  [S390] sclp_cpi module license.
  [S390] zcrypt: module unload fixes.
  [S390] Hipersocket multicast queue: make sure outbound handler is called
  [S390] hypfs fixes
  [S390] update default configuration