No one uses these functions, and some are duplicate of existing C code.  So
just punt the whole thing.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

These hardware devices are dead and the drivers never cleaned up/merged,
so punt the useless board resource info.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Since the exception handler cannot cause exceptions, we cannot trace it
without easily causing double faults and crashing the system.
Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

The BF522 and BF523 had their real max VCO values swapped.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

We have an item to get this fixed, but in the mean time, disable selection
via Kconfig dependencies.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

The handling of updating the [DI]MEM_CONTROL MMRs does not follow proper
sync procedures as laid out in the Blackfin programming manual.  So rather
than audit/fix every call location, create helper functions that do the
right things in order to safely update these MMRs.  Then convert all call
sites to use these new helper functions.

While we're fixing the code, drop the workaround for anomaly 05000125 as
that anomaly applies to old versions of silicon that we do not support.
Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Update the ad1836 resources for the new ASoC driver.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

The board has some parallel flash hooked up to the async banks, so add
appropriate physmap resources for it.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Check whether index is within bounds before testing the element.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

I think we have to use the physical dimensions [mm] of the display for
.width and .heigth in struct bfin_bf54xfb_mach_info bf54x_lq043_data which
are copied to fbinfo->var.height/.width in bf54x-lq043fb.c.

linux/fb.h describes this values as 'height/weight of picture in mm'

Otherwise QT calcs the wrong dpi value and the displayed fonts are very
small.
Signed-off-by: Stefan Pledl <stefan.pledl@mesutronic.de>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

The dm9000 driver expects two IORESOURCE_MEM to get at the device, so make
sure we declare things properly.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Latest smc91x driver allows you to specify settings in board resources
rather than needing CONFIG_BLACKFIN in the drivers/net/smc91x.h header.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

The interrupt probe workaround doesn't work without hacks to common code,
and the add-on card only needs a simple resistor to fix the problem, so
drop the board-specific hack.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Since the hardware only provides reporting for the last exception handled,
and the values are valid only when executing the exception handler, we
need to save the context for reporting at a later point.  While we do this
for one exception, it doesn't work properly when handling a second one as
the original exception is clobbered by the double fault.  So when double
fault debugging is enabled, create a dedicated shadow of these values and
save/restore out of there.  Now the crash report properly displays the
first exception as well as the second one.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

One too many zeros means we run way faster than the codec can handle.
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

The protect_page() function was incorrectly setting up the hardware tables
based on possible access capabilities rather than the actual requested
values.  This means we would grant more access to mmap-ed pages than we
should have.  Once we fix this, we need to tweak the signal generated by
such accesses to aline ourselves with other ports.  This allows the LTP
mmap0{5,6,7} cases to run properly.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

I2C_BOARD_INFO() already sets .type, no need to set it again.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Push the device table to the board resources as data interpretation can be
changed on a per-board basis.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

The end of the stack may not be valid (and that could be OK), so do not
attempt to parse it.  If we do, we might use a bad pointer in kernel space
which makes things panic().
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Add the bf538 version of bfin_clear_PPI_STATUS() to match all other ports.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

The initial BF54x port included some defines to keep code simple across
different processors, but it just ended up causing the UART0 DMA IRQs to
be set to the UART1 channels.
Signed-off-by: Stefan Pledl <stefan.pledl@mesutronic.de>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Allow hardware errors to be caught during early portions of booting, and
leave something in the shadow console that people can use to debug their
system with (to be printed out by the bootloader on next reset).

This enables the hardare error interrupts in head.S, allowing us to find
hardware errors when they happen (well, as much as you can with a hardware
error) and prints out the trace if it is enabled.  This will catch errors
(like booting the wrong image on a 533) which previously resulted in a
infinite loop/hang, as well as random hardware errors before before
setup_arch().

To disable this debug only feature - turn off EARLY_PRINTK.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Add a memory based shadow console to keep a copy of the printk buffer in a
location which can be found externally.  This allows bootloaders to locate
and utilize the log buffer in case of silent (early/resume/etc...) crashes.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

The FDPIC arches support a standard set of ptrace requests so rather than
define our own custom API, hook up those requests for common code to
leverage.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Rather than defining the locks and initializing them all the time, only do
so when we actually need them (i.e. the SRAM regions exist).  This avoids
dead data and code bloat during runtime.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

The "TWI_KEYPAD" driver was renamed to "INPUT_PCF8574", so update the
defines in the board resources accordingly.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Remove code duplication, and only print out memory warnings when they are
an actual problem.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

The current module relocation code has spotty handling wrt different
memory regions (like L1 instruction).  Rather than try to fix each
little spot, use the new common memory functions to greatly simplify
everything and make sure it is always correct.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

The current module section handling code has a lot of verbose statements
copied and pasted throughout which makes it pretty hard to digest at a
glance.  By unifying all of these up front, it is a lot easier to quickly
get an idea of what is actually going on.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Convert all printk() statements to use the common pr_xxx() funcs and use
the new pr_fmt() function to standardize all of the output.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

All kernel modules are required to be built with -mlong-calls and thus
should not generate any of these relocations.  If they do, it means the
module has not been compiled properly, so rather than trying to handle
them (and running into random run time errors) just error out on module
load to force the module to be compiled correctly.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Now that we have a Blackfin memory function to figure out how to properly
access the different regions, drop the custom memory range checks in our
ptrace code and use that.  It makes the code nicer and fixes bugs where
the ptrace logic wasn't handling all the different regions.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Unify the address display to shrink the code, and add missing decoding of
a few special Blackfin-specific regions (L1 ROM and MMRs).
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Signed-off-by: Philippe Gerum <rpm@xenomai.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Cleanup is performed in two ways:

- remove extraneous updates of IPEND[4] w/ CONFIG_IPIPE,
  and document remaining use.

- substitute pop-reg-from-stack instructions with plain SP fixups in
  all save-RETI-then-discard patterns.
Signed-off-by: Philippe Gerum <rpm@xenomai.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>