Previous default settings resulted in loose dynamic
range and low sound level.
New default configuration changes:
- outgain = 2
- quality mode = VLOW0
- dc remover = bypass
Signed-off-by: Irina Patru <ioana-irina.patru@nxp.com>
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1656405589-29850-1-git-send-email-shengjiu.wang@nxp.comSigned-off-by: Mark Brown <broonie@kernel.org>

In TDM mode, the BSEL register value must be set according to table 5 in the
datasheet. This patch adds a lookup function and uses it in
max98396_dai_tdm_slot().

As the first 3 entries can also be used for non-TDM setups, the code re-uses
the same table for such scenarios.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Link: https://lore.kernel.org/r/20220629050630.2848317-1-daniel@zonque.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Use dev_dbg on missing i2s->pinctrl as the pinctrl property is optional.

Fixes: 44f362c2 ("ASoC: rockchip: i2s: switch BCLK to GPIO")
Signed-off-by: Judy Hsiao <judyhsiao@chromium.org>
Link: https://lore.kernel.org/r/20220629080345.2427872-1-judyhsiao@chromium.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Add Machine driver support for audioreach solution, which uses
ADSP in SC7280 based paltforms.
Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
Link: https://lore.kernel.org/r/1656326662-14524-1-git-send-email-quic_srivasam@quicinc.comSigned-off-by: Mark Brown <broonie@kernel.org>

The documented yaml compat string for the apq8016 is
"qcom,apq8016-lpass-cpu" not "qcom,lpass-cpu-apq8016". Looking at the other
lpass compat strings the general form is "qcom,socnum-lpass-cpu".

We need to fix both the driver and dts to match.
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20220628120435.3044939-2-bryan.odonoghue@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Merge series from Shengjiu Wang <shengjiu.wang@nxp.com>:

Support PDM format and DSD format.
Add new dts property to configure dataline. The SAI has multiple
successive FIFO registers, but in some use
case the required dataline/FIFOs are not successive.

Merge series from Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>:

After a set of SOF-specific changes, this patchset correct problematic
uses of pm_runtime_get_sync() in ASoC, or simplifies the flow with no
functional changes. Two patches for Intel platforms also add a test on
resume success.

Additional changes were initially suggested to completely remove the
use of pm_runtime_get_sync(). These changes were dropped since they
are way too invasive, specifically in cases where the return values
were not tested, which would lead to duplicate pm_runtime_put(). The
remaining uses of pm_runtime_get_sync() cannot really be blindly
modified without context and knowledge of each driver.

h1940_uda1380 uses gpiod*/GPIOD* so it should include GPIO consumer
header.

Fixes: 9666e27f ("ASoC: samsung: h1940: turn into platform driver")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220627141900.470469-1-krzysztof.kozlowski@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Allow compile testing of Samsung SoC Sound drivers.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220627143412.477226-3-krzysztof.kozlowski@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

The module does not use anything from gpio.h header.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220627143412.477226-2-krzysztof.kozlowski@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

There is no particular need to restrict building of S3C I2S driver to
supported platforms within the C unit, because Kconfig does it.
Removing such restricting #ifdef from s3c-i2s-v2 allows compile testing
it on other platforms.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220627143412.477226-1-krzysztof.kozlowski@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Merge series from Daniel Mack <daniel@zonque.org>:

This is a series of some patches that I collected while using the
max98396 driver is a TDM mode setup.

They correct BSEL and PCM mode configs, add support for power supplies
and add some bits to the documentation.

The code is tested in TDM-16 and TDM-8 mode with 32 channel width.

Merge series from Samuel Holland <samuel@sholland.org>:

This series adds support for enabling the codec's internal microphone
bias, which is needed on at least some versions of the PinePhone.

Changes in v2:
 - Move register update from component probe to device probe

Arnaud Ferraris (2):
  ASoC: dt-bindings: sun50i-codec: Add binding for internal bias
  ASoC: sun50i-codec-analog: Add support for internal bias

Samuel Holland (1):
  arm64: dts: allwinner: pinephone: Enable internal HMIC bias

 .../bindings/sound/allwinner,sun50i-a64-codec-analog.yaml | 5 +++++
 .../arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.0.dts | 4 ++++
 .../arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts | 4 ++++
 sound/soc/sunxi/sun50i-codec-analog.c                     | 8 ++++++++
 4 files changed, 21 insertions(+)

--
2.35.1

The conversion of the set_fmt callback to direct clock specification
included a small typo, correct the affected code.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220627094335.3051210-1-ckeepax@opensource.cirrus.comSigned-off-by: Mark Brown <broonie@kernel.org>

Further development will need some of the fixes.

The SAI has multiple successive FIFO registers, but in some use
case the required dataline/FIFOs are not successive, so need
get such information from dts property "fsl,dataline"

fsl,dataline has 3 values for each configuration:
first one means the type: I2S(1) or DSD(2),
second one is dataline mask for 'rx',
third one is dataline mask for 'tx'.

Also set dma peripheral address and TRCE bits according to data lane.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Viorel Suman <viorel.suman@nxp.com>
Link: https://lore.kernel.org/r/1655451877-16382-8-git-send-email-shengjiu.wang@nxp.comSigned-off-by: Mark Brown <broonie@kernel.org>

"fsl,dataline" is added to configure the dataline of SAI.
It has 3 value for each configuration, first one means the type:
I2S(1) or PDM(2), second one is dataline mask for 'rx', third one is
dataline mask for 'tx'. for example:

fsl,dataline = <1 0xff 0xff 2 0xff 0x11>,

it means I2S type rx mask is 0xff, tx mask is 0xff, PDM type
rx mask is 0xff, tx mask is 0x11 (dataline 1 and 4 enabled).
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1655451877-16382-7-git-send-email-shengjiu.wang@nxp.comSigned-off-by: Mark Brown <broonie@kernel.org>

The resource info need to be accessed by hw_params()
function for multi fifo case, the start address may
be not the FIFO0. So move it to be a member of
struct fsl_sai.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1655451877-16382-6-git-send-email-shengjiu.wang@nxp.comSigned-off-by: Mark Brown <broonie@kernel.org>

With DSD format, the pinctrl is different compare with
I2S format, because one dataline only has one channel
data, and the codec always mux the LRCLK pin to DSD
data line, and on i.MX8MQ the BCLK pin can route to
codec on DSD case for the MCLK is too high.

Add pinctrl operation that the pinctrl can be switched
on runtime according to the I2S format or DSD format
Signed-off-by: Viorel Suman <viorel.suman@nxp.com>
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1655451877-16382-5-git-send-email-shengjiu.wang@nxp.comSigned-off-by: Mark Brown <broonie@kernel.org>

Add support for more sample rates, because PDM format
bitstream has higher sample rates. for example DSD512
format, the bit clock is 22.5792MHz, if the word width
is U8_LE, then the max sample rate is 2822400.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1655451877-16382-4-git-send-email-shengjiu.wang@nxp.comSigned-off-by: Mark Brown <broonie@kernel.org>

Support DSD_U8, DSD_U16_LE, DSD_U32_LE.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1655451877-16382-3-git-send-email-shengjiu.wang@nxp.comSigned-off-by: Mark Brown <broonie@kernel.org>

PDM format is used for 1-bit stream, so clear the FBT and SYWD,
and the each dataline only has one channel data.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1655451877-16382-2-git-send-email-shengjiu.wang@nxp.comSigned-off-by: Mark Brown <broonie@kernel.org>

In order to properly bias headset microphones, there should be a pull-up
resistor between pins HBIAS and MIC2P. This can be an external resistor,
but the codec also provides an internal 2.2K resistor which is enabled
by a register.

This patch enables or disables the internal bias resistor based on a
device tree property.
Signed-off-by: Arnaud Ferraris <arnaud.ferraris@collabora.com>
[Samuel: split binding and implementation; move to device probe]
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20220621035452.60272-3-samuel@sholland.orgSigned-off-by: Mark Brown <broonie@kernel.org>

In order to properly bias headset microphones, there should be a pull-up
resistor between pins HBIAS and MIC2P. This can be an external resistor,
but the codec also provides an internal 2.2K resistor which is enabled
by a register.

This patch adds a device-tree property to the sun50i-codec-analog driver
to take advantage of this feature.
Signed-off-by: Arnaud Ferraris <arnaud.ferraris@collabora.com>
[Samuel: split binding and implementation patches]
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20220621035452.60272-2-samuel@sholland.orgSigned-off-by: Mark Brown <broonie@kernel.org>

The use of pm_runtime_get_sync() is buggy with no use of put_noidle on
error.

Use pm_runtime_resume_and_get() instead.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20220616220427.136036-12-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

The use of pm_runtime_get_sync() is buggy with no use of put_noidle() on
error.

Use pm_runtime_resume_and_get() instead.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20220616220427.136036-11-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Simplify the flow.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20220616220427.136036-10-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Simplify the flow.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20220616220427.136036-9-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Simplify the flow.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20220616220427.136036-8-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

simplify the flow. No functionality change, except that on -EACCESS
the reference count will be decreased.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20220616220427.136036-7-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

simplify the flow. No functionality change, except that on -EACCESS
the reference count will be decreased.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20220616220427.136036-6-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

simplify the flow. No functionality change, except that on -EACCESS
the reference count will be decreased.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20220616220427.136036-5-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

The current code does not check for errors and does not release the
reference on errors.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Acked-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20220616220427.136036-3-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

The current code does not check for errors and does not release the
reference on errors.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Acked-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20220616220427.136036-2-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Allow the selection of the TDM slot that is used to send back speaker
monitor data. The DT property adi,spkfb-slot-no can be used to configure
this setting which defaults to 2.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Link: https://lore.kernel.org/r/20220624104712.1934484-8-daniel@zonque.orgSigned-off-by: Mark Brown <broonie@kernel.org>

max98396_dai_set_fmt() modifes register 2041 and touches bits in the mask
0x3a. Make sure to use the right mask for that operation.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Link: https://lore.kernel.org/r/20220624104712.1934484-7-daniel@zonque.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Let's log what actually failed and log at some more places.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Link: https://lore.kernel.org/r/20220624104712.1934484-6-daniel@zonque.orgSigned-off-by: Mark Brown <broonie@kernel.org>

The device has up to 5 potentially independent power supplies:
AVDD, DVDD, DVVDIO, VBAT and PVDD. The former 3 are mandatory for the
device to function. One of VBAT and PVDD should also be made available.

Regulators are enabled during probe time and will stay active except when in
suspend mode.

Futher, the chip needs to be informed about the presence of VBAT through a
bit in register 0x20a0.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Link: https://lore.kernel.org/r/20220624104712.1934484-5-daniel@zonque.orgSigned-off-by: Mark Brown <broonie@kernel.org>

This property allows to select the PCM data input channel that is
routed to the speaker audio processing bypass path.

The driver already implements this property.

While at it, fix the default value for adi,imon-slot-no.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Link: https://lore.kernel.org/r/20220624104712.1934484-4-daniel@zonque.orgSigned-off-by: Mark Brown <broonie@kernel.org>

The device is supplied with 3 core voltages (DVVDIO, DVDD, AVDD), and
PVDD and/or VBAT.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Link: https://lore.kernel.org/r/20220624104712.1934484-2-daniel@zonque.orgSigned-off-by: Mark Brown <broonie@kernel.org>