imx6ul-14x14-evk does not have a GPIO dedicated for reading the card
detect pin on the eSDHC2 micro-SD port.

Pass the "broken-cd" property to describe the absence of the card detect
GPIO so that polling must be used.

According to Documentation/devicetree/bindings/mmc/mmc-controller.yaml:

  broken-cd:
    $ref: /schemas/types.yaml#/definitions/flag
    description:
      There is no card detection available; polling must be used.

Even though no error is oberved in the kernel, the lack of the
'broken-cd' property caused the micro-SD to not be detected in U-Boot,
so let's improve the device tree description to make it more accurate.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The vdd3p0 LDO's input should be from external USB VBUS directly, NOT
PMIC's power supply, the vdd3p0 LDO's target output voltage can be
controlled by SW, and it requires input voltage to be high enough, with
incorrect power supply assigned, if the power supply's voltage is lower
than the LDO target output voltage, it will return fail and skip the LDO
voltage adjustment, so remove the power supply assignment for vdd3p0 to
avoid such scenario.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add support for the VXT VL050-8048NT-C01 panel connected through
the 24 bit parallel LCDIF interface.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

LAN8720 needs a reset of every clock enable. The reset needs
to be done at device level, due the flag PHY_RST_AFTER_CLK_EN.

So, add phy-handle by creating mdio child node inside fec.
This will eventually move the phy-reset-gpio which is defined
in fec node.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Engicam i.CoreM6 1.5 Quad/Dual MIPI dtsi is reusing fec node
from Engicam i.CoreM6 dtsi but have sampe copy of phy-reset-gpio
and phy-mode properties.

So, drop this phy reset methods from imx6qdl-icore-1.5 dsti file.

Cc: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The following warning is seen when building with W=1:

arch/arm/boot/dts/imx7s.dtsi:551.39-553.7: Warning (unique_unit_address): /soc/aips-bus@30000000/ocotp-ctrl@30350000/temp-grade@10: duplicate unit-address (also used in node /soc/aips-bus@30000000/ocotp-ctrl@30350000/speed-grade@10)

Since temp-grade and speed-grade point to the same node, replace them by
a single one to avoid the duplicate unit-address warning.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Without the onkey device it isn't possible to power off the system using
the X_PMIC_nONKEY signal which is routed to the SoM pin header.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

imx51-babbage has a TFP410 chip that receives 24-bit RGB parallel
input and convert it to DVI.

Fix the device tree description to reflect the real hardware.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Mux the HDMI CEC pin to make HDMI CEC working. With this change HDMI CEC
seems to work fine on a Apalis iMX6 on Ixora using cec-ctl.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

While the EPDC is optional, both consumer and industrial editions
have the PXP module, so adding it to the corresponding .dtsi
Information taken from freescale kernel, compared with the
reference manual and tested by a separate program.

Since it does not depend on external wiring, the
status = "disabled" is left out here.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Some pinmuxings are obviously wrong, originating from a copy/paste
error. This patch corrects that with the following strategy:

- Set all reserved bits to zero
- Leave drive strength and slew rate as is
- Add sensible pull and hysteresis depending on the function of the pin
- Not used pins are muxed to their reset-value defined by the SoC
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add I2C child node for switch watchdog present on SCU4.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The devicetree specification recommends using generic node names.

Some ZII dts files already follow such recommendation, but some don't,
so use generic node names for consistency among the ZII dts files.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

ZII VF610 Board Rev. B is supposed to have exactly the same I2C config
as Rev. C, including I2C bus recovery settings. Drop redundant I2C
properties that are already specified in vf610-zii-dev.dtsi
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This patch sets initial buck regulator modes explicitly to a state this
hardware needs. So a wrong initial mode set by bootloader or pmic itself
does not interfere anymore.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Cabling used to connect devices to USBH1 on RDU2 does not meet USB
spec cable quality and cable length requirements to operate at High
Speed, so limit the port to Full Speed only.
Reported-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

RDU2 production units come with resistor connecting WP pin to
correpsonding GPIO DNPed for both SD card slots. Drop any WP related
configuration and mark both slots with "disable-wp".
Reported-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add node for UCS1002 USB charger chip connected to front panel USB and
replace "regulator-fixed" previously used to control VBUS.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Otherwise, the system will hang if USB driver try to access
portsc register.

Cc: André Draszik <git@andred.net>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The Embedded Artists COM board is based on NXP i.MX7ULP.

It has a BD70528 PMIC from Rohm with discrete DCDC powering option and
improved current observability (compared to the existing NXP i.MX7ULP EVK).

Add the initial support for the board.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

On the LS1021A-TSN board, the 2 Atheros AR8031 PHYs for eth0 and eth1
have interrupt lines connected to the shared IRQ2_B LS1021A pin.

Switching to interrupts offloads the PHY library from the task of
polling the MDIO status and AN registers (1, 4, 5) every second.

Unfortunately, the BCM5464R quad PHY connected to the switch does not
appear to have an interrupt line routed to the SoC.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This adds a node describing the six external interrupt lines IRQ0-IRQ5
with configurable polarity.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The internal usbphy of usbhost port1 is only full-speed capable.
We set this limitation in the dtsi.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The usb port represented by &usbhost1 uses an USB phy internal to the
SoC. We add the phy_type to the base dtsi so the board dts only have to
overwrite it if they use a different configuration. While at it we also
pin the usbhost port to host mode.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The following build warning is seen with W=1:

  DTC     arch/arm/boot/dts/imx6sll-kobo-clarahd.dtb
arch/arm/boot/dts/e60k02.dtsi:51.9-53.4: Warning (unit_address_vs_reg): /memory: node has a reg or ranges property, but no unit name

Pass the memory unit address to fix the problem.

While at it, also pass 'device_type = "memory"', which is recommended
for memory nodes.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The device is almost identical to the Kobo Clara HD. The only
spotted difference is the SoC. It contains an imx6sl
instead of an imx6sll.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Tested-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

i.MX7D SDB Rev-A board should use its own board compatible
string instead of default i.MX7D SDB board.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

i.MX6SX SDB Rev-A board should use its own board compatible
string instead of default i.MX6SX SDB board.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The LCD used with the imx6q-logicpd board has an integrated
ili2117a touch controller connected to i2c1.

This patch adds the node to enable this feature.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Pull networking fixes from David Miller:

 1) More jumbo frame fixes in r8169, from Heiner Kallweit.

 2) Fix bpf build in minimal configuration, from Alexei Starovoitov.

 3) Use after free in slcan driver, from Jouni Hogander.

 4) Flower classifier port ranges don't work properly in the HW offload
    case, from Yoshiki Komachi.

 5) Use after free in hns3_nic_maybe_stop_tx(), from Yunsheng Lin.

 6) Out of bounds access in mqprio_dump(), from Vladyslav Tarasiuk.

 7) Fix flow dissection in dsa TX path, from Alexander Lobakin.

 8) Stale syncookie timestampe fixes from Guillaume Nault.

[ Did an evil merge to silence a warning introduced by this pull - Linus ]

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (84 commits)
  r8169: fix rtl_hw_jumbo_disable for RTL8168evl
  net_sched: validate TCA_KIND attribute in tc_chain_tmplt_add()
  r8169: add missing RX enabling for WoL on RTL8125
  vhost/vsock: accept only packets with the right dst_cid
  net: phy: dp83867: fix hfs boot in rgmii mode
  net: ethernet: ti: cpsw: fix extra rx interrupt
  inet: protect against too small mtu values.
  gre: refetch erspan header from skb->data after pskb_may_pull()
  pppoe: remove redundant BUG_ON() check in pppoe_pernet
  tcp: Protect accesses to .ts_recent_stamp with {READ,WRITE}_ONCE()
  tcp: tighten acceptance of ACKs not matching a child socket
  tcp: fix rejected syncookies due to stale timestamps
  lpc_eth: kernel BUG on remove
  tcp: md5: fix potential overestimation of TCP option space
  net: sched: allow indirect blocks to bind to clsact in TC
  net: core: rename indirect block ingress cb function
  net-sysfs: Call dev_hold always in netdev_queue_add_kobject
  net: dsa: fix flow dissection on Tx path
  net/tls: Fix return values to avoid ENOTSUPP
  net: avoid an indirect call in ____sys_recvmsg()
  ...

Pull more SCSI updates from James Bottomley:
 "Eleven patches, all in drivers (no core changes) that are either minor
  cleanups or small fixes.

  They were late arriving, but still safe for -rc1"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: MAINTAINERS: Add the linux-scsi mailing list to the ISCSI entry
  scsi: megaraid_sas: Make poll_aen_lock static
  scsi: sd_zbc: Improve report zones error printout
  scsi: qla2xxx: Fix qla2x00_request_irqs() for MSI
  scsi: qla2xxx: unregister ports after GPN_FT failure
  scsi: qla2xxx: fix rports not being mark as lost in sync fabric scan
  scsi: pm80xx: Remove unused include of linux/version.h
  scsi: pm80xx: fix logic to break out of loop when register value is 2 or 3
  scsi: scsi_transport_sas: Fix memory leak when removing devices
  scsi: lpfc: size cpu map by last cpu id set
  scsi: ibmvscsi_tgt: Remove unneeded variable rc

Pull cifs fixes from Steve French:
 "Nine cifs/smb3 fixes:

   - one fix for stable (oops during oplock break)

   - two timestamp fixes including important one for updating mtime at
     close to avoid stale metadata caching issue on dirty files (also
     improves perf by using SMB2_CLOSE_FLAG_POSTQUERY_ATTRIB over the
     wire)

   - two fixes for "modefromsid" mount option for file create (now
     allows mode bits to be set more atomically and accurately on create
     by adding "sd_context" on create when modefromsid specified on
     mount)

   - two fixes for multichannel found in testing this week against
     different servers

   - two small cleanup patches"

* tag '5.5-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
  smb3: improve check for when we send the security descriptor context on create
  smb3: fix mode passed in on create for modetosid mount option
  cifs: fix possible uninitialized access and race on iface_list
  cifs: Fix lookup of SMB connections on multichannel
  smb3: query attributes on file close
  smb3: remove unused flag passed into close functions
  cifs: remove redundant assignment to pointer pneg_ctxt
  fs: cifs: Fix atime update check vs mtime
  CIFS: Fix NULL-pointer dereference in smb2_push_mandatory_locks

Pull misc vfs cleanups from Al Viro:
 "No common topic, just three cleanups".

* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  make __d_alloc() static
  fs/namespace: add __user to open_tree and move_mount syscalls
  fs/fnctl: fix missing __user in fcntl_rw_hint()

Pull NTB update from Jon Mason:
 "Just a simple patch to add a new Hygon Device ID to the AMD NTB device
  driver"

* tag 'ntb-5.5' of git://github.com/jonmason/ntb:
  NTB: Add Hygon Device ID

Pull more input updates from Dmitry Torokhov:

 - fixups for Synaptics RMI4 driver

 - a quirk for Goodinx touchscreen on Teclast tablet

 - a new keycode definition for activating privacy screen feature found
   on a few "enterprise" laptops

 - updates to snvs_pwrkey driver

 - polling uinput device for writing (which is always allowed) now works

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: synaptics-rmi4 - don't increment rmiaddr for SMBus transfers
  Input: synaptics-rmi4 - re-enable IRQs in f34v7_do_reflash
  Input: goodix - add upside-down quirk for Teclast X89 tablet
  Input: add privacy screen toggle keycode
  Input: uinput - fix returning EPOLLOUT from uinput_poll
  Input: snvs_pwrkey - remove gratuitous NULL initializers
  Input: snvs_pwrkey - send key events for i.MX6 S, DL and Q

Pull iomap fixes from Darrick Wong:
 "Fix a race condition and a use-after-free error:

   - Fix a UAF when reporting writeback errors

   - Fix a race condition when handling page uptodate on fragmented file
     with blocksize < pagesize"

* tag 'iomap-5.5-merge-14' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  iomap: stop using ioend after it's been freed in iomap_finish_ioend()
  iomap: fix sub-page uptodate handling

Pull xfs fixes from Darrick Wong:
 "Fix a couple of resource management errors and a hang:

   - fix a crash in the log setup code when log mounting fails

   - fix a hang when allocating space on the realtime device

   - fix a block leak when freeing space on the realtime device"

* tag 'xfs-5.5-merge-17' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  xfs: fix mount failure crash on invalid iclog memory access
  xfs: don't check for AG deadlock for realtime files in bunmapi
  xfs: fix realtime file data space leak

Pull orangefs update from Mike Marshall:
 "orangefs: posix open permission checking...

  Orangefs has no open, and orangefs checks file permissions on each
  file access. Posix requires that file permissions be checked on open
  and nowhere else. Orangefs-through-the-kernel needs to seem posix
  compliant.

  The VFS opens files, even if the filesystem provides no method. We can
  see if a file was successfully opened for read and or for write by
  looking at file->f_mode.

  When writes are flowing from the page cache, file is no longer
  available. We can trust the VFS to have checked file->f_mode before
  writing to the page cache.

  The mode of a file might change between when it is opened and IO
  commences, or it might be created with an arbitrary mode.

  We'll make sure we don't hit EACCES during the IO stage by using
  UID 0"

[ This is "posixish", but not a great solution in the long run, since a
  proper secure network server shouldn't really trust the client like this.
  But proper and secure POSIX behavior requires an open method and a
  resulting cookie for IO of some kind, or similar.    - Linus ]

* tag 'for-linus-5.5-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux:
  orangefs: posix open permission checking...

Pull nfsd updates from Bruce Fields:
 "This is a relatively quiet cycle for nfsd, mainly various bugfixes.

  Possibly most interesting is Trond's fixes for some callback races
  that were due to my incomplete understanding of rpc client shutdown.
  Unfortunately at the last minute I've started noticing a new
  intermittent failure to send callbacks. As the logic seems basically
  correct, I'm leaving Trond's patches in for now, and hope to find a
  fix in the next week so I don't have to revert those patches"

* tag 'nfsd-5.5' of git://linux-nfs.org/~bfields/linux: (24 commits)
  nfsd: depend on CRYPTO_MD5 for legacy client tracking
  NFSD fixing possible null pointer derefering in copy offload
  nfsd: check for EBUSY from vfs_rmdir/vfs_unink.
  nfsd: Ensure CLONE persists data and metadata changes to the target file
  SUNRPC: Fix backchannel latency metrics
  nfsd: restore NFSv3 ACL support
  nfsd: v4 support requires CRYPTO_SHA256
  nfsd: Fix cld_net->cn_tfm initialization
  lockd: remove __KERNEL__ ifdefs
  sunrpc: remove __KERNEL__ ifdefs
  race in exportfs_decode_fh()
  nfsd: Drop LIST_HEAD where the variable it declares is never used.
  nfsd: document callback_wq serialization of callback code
  nfsd: mark cb path down on unknown errors
  nfsd: Fix races between nfsd4_cb_release() and nfsd4_shutdown_callback()
  nfsd: minor 4.1 callback cleanup
  SUNRPC: Fix svcauth_gss_proxy_init()
  SUNRPC: Trace gssproxy upcall results
  sunrpc: fix crash when cache_head become valid before update
  nfsd: remove private bin2hex implementation
  ...