Add driver providing access to EEPROMs connected to RAVE SP devices

Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: linux-kernel@vger.kernel.org
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add Device Tree bindings for RAVE SP EEPROM driver - an MFD cell of
parent RAVE SP driver (documented in
Documentation/devicetree/bindings/mfd/zii,rave-sp.txt).

Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: linux-kernel@vger.kernel.org
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Aleksander Morgado <aleksander@aleksander.es>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Not all platforms use device tree. It is useful to be able to add
cells to a NVMEM device from code. Export nvmem_add_cells() so making
this possible.

This required changing the parameters a bit, so that just the cells
and the number of cells are passed, not the whole nvmem config
structure.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The driver prints pcsr twice: the first time it uses specifier %px to
print hexadecimal pcsr value and the second time uses specifier %pS for
output kernel symbols.

As suggested by Kees, using %pS should be sufficient and %px isn't
necessary; the reason is if the pcsr is a kernel space address, we can
easily get to know the code line from %pS format, on the other hand, if
the pcsr value doesn't fall into kernel space range (e.g. if the CPU is
stuck in firmware), %pS also gives out pcsr hexadecimal value.

So this commit removes useless %px and update section "Output format"
in the document for alignment between the code and document.
Suggested-by: Kees Cook <keescook@chromium.org>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The simple removal of an extra newline, no change in functionality.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Variable 'paddr' can't be used if uninitialised but is nonetheless
confusing to some static checker.  As such simply initialise it to zero.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

While operating from sysFS the TMC-ETR driver needs to make sure it has
memory to work with but doesn't allocate memory uselessly either.  Since
the main memory handle for this driver is drvdata::vaddr, use it throughout
function tmc_enable_etr_sink_sysfs() so that things are consistent.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Moving all kernel side CoreSight framework and drivers to SPDX identifier.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Never directly free @dev after calling device_register(), even
if it returned an error. Always use put_device() to give up the
reference initialized.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Prevent destruction of a uio_device while user space apps hold open
file descriptors to that device. Further, access to the 'info' member
of the struct uio_device is protected by spinlock. This is to ensure
stale pointers to data not under control of the UIO subsystem are not
dereferenced.
Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Drive all return paths for uio_write() through a single block at the
end of the function.
Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In 4.9 kernel, the sysfs files for Hyper-V VMBus changed name but
the documentation files were not updated. The current sysfs file
names are /sys/bus/vmbus/devices/<UUID>/...

See commit 9a56e5d6a0ba ("Drivers: hv: make VMBus bus ids persistent")
and commit f6b2db08 ("vmbus: make sysfs names consistent with PCI")
Reported-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Cc: stable@vger.kernel.org
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

With VMBus protocol 5.0, we're able to better support new features, e.g.
running two or more VMBus drivers simultaneously in a single VM -- note:
we can't simply load the current VMBus driver twice, instead, a secondary
VMBus driver must be implemented.

This patch adds the support for the new VMBus protocol, which is available
on new Windows hosts, by:

1) We still use SINT2 for compatibility;
2) We must use Connection ID 4 for the Initiate Contact Message, and for
subsequent messages, we must use the Message Connection ID field in
the host-returned VersionResponse Message.

Notes for developers of the secondary VMBus driver:
1) Must use VMBus protocol 5.0 as well;
2) Must use a different SINT number that is not in use.
3) Must use Connection ID 4 for the Initiate Contact Message, and for
subsequent messages, must use the Message Connection ID field in
the host-returned VersionResponse Message.
4) It's possible that the primary VMBus driver using protocol version 4.0
can work with a secondary VMBus driver using protocol version 5.0, but it's
recommended that both should use 5.0 for new Hyper-V features in the future.
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Cc: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use new return type vm_fault_t for fault handler in
struct vm_operations_struct. For now, this is just
documenting that the function returns a VM_FAULT
value rather than an errno.  Once all instances are
converted, vm_fault_t will become a distinct type.

Reference id -> 1c8f4220 ("mm: change return type
to vm_fault_t")
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

binder_update_page_range needs down_write of mmap_sem because
vm_insert_page need to change vma->vm_flags to VM_MIXEDMAP unless
it is set. However, when I profile binder working, it seems
every binder buffers should be mapped in advance by binder_mmap.
It means we could set VM_MIXEDMAP in binder_mmap time which is
already hold a mmap_sem as down_write so binder_update_page_range
doesn't need to hold a mmap_sem as down_write.
Please use proper API down_read. It would help mmap_sem contention
problem as well as fixing down_write abuse.

Ganesh Mahendran tested app launching and binder throughput test
and he said he couldn't find any problem and I did binder latency
test per Greg KH request(Thanks Martijn to teach me how I can do)
I cannot find any problem, too.

Cc: Ganesh Mahendran <opensource.ganesh@gmail.com>
Cc: Joe Perches <joe@perches.com>
Cc: Arve Hjønnevåg <arve@android.com>
Cc: Todd Kjos <tkjos@google.com>
Reviewed-by: Martijn Coenen <maco@android.com>
Signed-off-by: Minchan Kim <minchan@kernel.org>
Reviewed-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When to execute binder_stat_br the e->cmd has been modifying as BR_OK
instead of the original return error cmd, in fact we want to know the
original return error, such as BR_DEAD_REPLY or BR_FAILED_REPLY, etc.
instead of always BR_OK, in order to avoid the value of the e->cmd is
always BR_OK, so we need assign the value of the e->cmd to cmd before
e->cmd = BR_OK.
Signed-off-by: songjinshi <songjinshi@xiaomi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

New devices launching with Android P need to use the 64-bit
binder interface, even on 32-bit SoCs [0].

This change removes the Kconfig option to select the 32-bit
binder interface. We don't think this will affect existing
userspace for the following reasons:
1) The latest Android common tree is 4.14, so we don't
   believe any Android devices are on kernels >4.14.
2) Android devices launch on an LTS release and stick with
   it, so we wouldn't expect devices running on <= 4.14 now
   to upgrade to 4.17 or later. But even if they did, they'd
   rebuild the world (kernel + userspace) anyway.
3) Other userspaces like 'anbox' are already using the
   64-bit interface.

Note that this change doesn't remove the 32-bit UAPI
itself; the reason for that is that Android userspace
always uses the latest UAPI headers from upstream, and
userspace retains 32-bit support for devices that are
upgrading. This will be removed as well in 2-3 years,
at which point we can remove the code from the UAPI
as well.

Finally, this change introduces build errors on archs where
64-bit get_user/put_user is not supported, so make binder
unavailable on m68k (which wouldn't want it anyway).

[0]: https://android-review.googlesource.com/c/platform/build/+/595193Signed-off-by: Martijn Coenen <maco@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'soundwire-streaming' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire into char-misc-next

Vinod writes:

soundwire streaming

This contains:
 - Support for SoundWire Streaming
 - Documentation updates for streaming
 - Cadence and Intel driver updates for streaming
 - ASoC API for programming soundwire stream

Add DAI registration and DAI ops for the Intel driver along with
callback for topology configuration.
Signed-off-by: Sanyog Kale <sanyog.r.kale@intel.com>
Signed-off-by: Shreyas NC <shreyas.nc@intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>

Add Intel stream init routines which initialize the Physical
Data Interface (PDI), Audio Link Hub (ALH) and Audio shim.
Also add bank switch routines.
Signed-off-by: Hardik T Shah <hardik.t.shah@intel.com>
Signed-off-by: Sanyog Kale <sanyog.r.kale@intel.com>
Signed-off-by: Shreyas NC <shreyas.nc@intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>

Add support for Cadence stream initialization and implement
stream APIs.
Signed-off-by: Sanyog Kale <sanyog.r.kale@intel.com>
Signed-off-by: Shreyas NC <shreyas.nc@intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>

Add support for Cadence port management and implement
master port ops.
Signed-off-by: Sanyog Kale <sanyog.r.kale@intel.com>
Signed-off-by: Shreyas NC <shreyas.nc@intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>

There can be instances where drivers using Cadence IP might want
to set sdw_master_ops differently per instance of it's use, so
remove the cdns_master_ops and export the APIs.
Signed-off-by: Shreyas NC <shreyas.nc@intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>

SoundWire stream needs to be propagated to all the DAIs(cpu, codec).
So, add a snd_soc_dai_set_sdw_stream() API for the same.
Signed-off-by: Shreyas NC <shreyas.nc@intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>

Add APIs for prepare, enable, disable and de-prepare stream.
Signed-off-by: Sanyog Kale <sanyog.r.kale@intel.com>
Signed-off-by: Shreyas NC <shreyas.nc@intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>

SoundWire supports two registers banks. So, program the alternate bank
with new configuration and then performs bank switch.
Signed-off-by: Sanyog Kale <sanyog.r.kale@intel.com>
Signed-off-by: Shreyas NC <shreyas.nc@intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>

Add helpers to configure, prepare, enable, disable and
de-prepare ports.
Signed-off-by: Sanyog Kale <sanyog.r.kale@intel.com>
Signed-off-by: Shreyas NC <shreyas.nc@intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>

Master and Slave port registers need to be programmed for each port
used in a stream. Add the helpers for port register programming.
Signed-off-by: Sanyog Kale <sanyog.r.kale@intel.com>
Signed-off-by: Shreyas NC <shreyas.nc@intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>

Add Soundwire port data structures and APIS for initialization
and release of ports.
Signed-off-by: Sanyog Kale <sanyog.r.kale@intel.com>
Signed-off-by: Shreyas NC <shreyas.nc@intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>

This patch adds APIs and relevant stream data structures
for initialization and release of stream.
Signed-off-by: Hardik T Shah <hardik.t.shah@intel.com>
Signed-off-by: Sanyog Kale <sanyog.r.kale@intel.com>
Signed-off-by: Shreyas NC <shreyas.nc@intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>

This adds documentation for error handling, locking and streams.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Sanyog Kale <sanyog.r.kale@intel.com>
Signed-off-by: Shreyas NC <shreyas.nc@intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>

Update the email address for SoundWire maintainer
Signed-off-by: Vinod Koul <vkoul@kernel.org>

We want the fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull x86 fixes from Thomas Gleixner:
 "Another set of x86 related updates:

   - Fix the long broken x32 version of the IPC user space headers which
     was noticed by Arnd Bergman in course of his ongoing y2038 work.
     GLIBC seems to have non broken private copies of these headers so
     this went unnoticed.

   - Two microcode fixlets which address some more fallout from the
     recent modifications in that area:

      - Unconditionally save the microcode patch, which was only saved
        when CPU_HOTPLUG was enabled causing failures in the late
        loading mechanism

      - Make the later loader synchronization finally work under all
        circumstances. It was exiting early and causing timeout failures
        due to a missing synchronization point.

   - Do not use mwait_play_dead() on AMD systems to prevent excessive
     power consumption as the CPU cannot go into deep power states from
     there.

   - Address an annoying sparse warning due to lost type qualifiers of
     the vmemmap and vmalloc base address constants.

   - Prevent reserving crash kernel region on Xen PV as this leads to
     the wrong perception that crash kernels actually work there which
     is not the case. Xen PV has its own crash mechanism handled by the
     hypervisor.

   - Add missing TLB cpuid values to the table to make the printout on
     certain machines correct.

   - Enumerate the new CLDEMOTE instruction

   - Fix an incorrect SPDX identifier

   - Remove stale macros"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/ipc: Fix x32 version of shmid64_ds and msqid64_ds
  x86/setup: Do not reserve a crash kernel region if booted on Xen PV
  x86/cpu/intel: Add missing TLB cpuid values
  x86/smpboot: Don't use mwait_play_dead() on AMD systems
  x86/mm: Make vmemmap and vmalloc base address constants unsigned long
  x86/vector: Remove the unused macro FPU_IRQ
  x86/vector: Remove the macro VECTOR_OFFSET_START
  x86/cpufeatures: Enumerate cldemote instruction
  x86/microcode: Do not exit early from __reload_late()
  x86/microcode/intel: Save microcode patch unconditionally
  x86/jailhouse: Fix incorrect SPDX identifier

Pull x86 pti fixes from Thomas Gleixner:
 "A set of updates for the x86/pti related code:

   - Preserve r8-r11 in int $0x80. r8-r11 need to be preserved, but the
     int$80 entry code removed that quite some time ago. Make it correct
     again.

   - A set of fixes for the Global Bit work which went into 4.17 and
     caused a bunch of interesting regressions:

      - Triggering a BUG in the page attribute code due to a missing
        check for early boot stage

      - Warnings in the page attribute code about holes in the kernel
        text mapping which are caused by the freeing of the init code.
        Handle such holes gracefully.

      - Reduce the amount of kernel memory which is set global to the
        actual text and do not incidentally overlap with data.

      - Disable the global bit when RANDSTRUCT is enabled as it
        partially defeats the hardening.

      - Make the page protection setup correct for vma->page_prot
        population again. The adjustment of the protections fell through
        the crack during the Global bit rework and triggers warnings on
        machines which do not support certain features, e.g. NX"

* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/entry/64/compat: Preserve r8-r11 in int $0x80
  x86/pti: Filter at vma->vm_page_prot population
  x86/pti: Disallow global kernel text with RANDSTRUCT
  x86/pti: Reduce amount of kernel text allowed to be Global
  x86/pti: Fix boot warning from Global-bit setting
  x86/pti: Fix boot problems from Global-bit setting

Pull timer fixes from Thomas Gleixner:
 "Two fixes from the timer departement:

   - Fix a long standing issue in the NOHZ tick code which causes RB
     tree corruption, delayed timers and other malfunctions. The cause
     for this is code which modifies the expiry time of an enqueued
     hrtimer.

   - Revert the CLOCK_MONOTONIC/CLOCK_BOOTTIME unification due to
     regression reports. Seems userspace _is_ relying on the documented
     behaviour despite our hope that it wont"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  Revert: Unify CLOCK_MONOTONIC and CLOCK_BOOTTIME
  tick/sched: Do not mess with an enqueued hrtimer

Pull perf fixes from Thomas Gleixner:
 "The perf update contains the following bits:

  x86:
   - Prevent setting freeze_on_smi on PerfMon V1 CPUs to avoid #GP

  perf stat:
   - Keep the '/' event modifier separator in fallback, for example when
     fallbacking from 'cpu/cpu-cycles/' to user level only, where it
     should become 'cpu/cpu-cycles/u' and not 'cpu/cpu-cycles/:u' (Jiri
     Olsa)

   - Fix PMU events parsing rule, improving error reporting for invalid
     events (Jiri Olsa)

   - Disable write_backward and other event attributes for !group events
     in a group, fixing, for instance this group: '{cycles,msr/aperf/}:S'
     that has leader sampling (:S) and where just the 'cycles', the
     leader event, should have the write_backward attribute set, in this
     case it all fails because the PMU where 'msr/aperf/' lives doesn't
     accepts write_backward style sampling (Jiri Olsa)

   - Only fall back group read for leader (Kan Liang)

   - Fix core PMU alias list for x86 platform (Kan Liang)

   - Print out hint for mixed PMU group error (Kan Liang)

   - Fix duplicate PMU name for interval print (Kan Liang)

  Core:
   - Set main kernel end address properly when reading kernel and module
     maps (Namhyung Kim)

  perf mem:
   - Fix incorrect entries and add missing man options (Sangwon Hong)

  s/390:
   - Remove s390 specific strcmp_cpuid_cmp function (Thomas Richter)

   - Adapt 'perf test' case record+probe_libc_inet_pton.sh for s390

   - Fix s390 undefined record__auxtrace_init() return value in 'perf
     record' (Thomas Richter)"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/x86/intel: Don't enable freeze-on-smi for PerfMon V1
  perf stat: Fix duplicate PMU name for interval print
  perf evsel: Only fall back group read for leader
  perf stat: Print out hint for mixed PMU group error
  perf pmu: Fix core PMU alias list for X86 platform
  perf record: Fix s390 undefined record__auxtrace_init() return value
  perf mem: Document incorrect and missing options
  perf evsel: Disable write_backward for leader sampling group events
  perf pmu: Fix pmu events parsing rule
  perf stat: Keep the / modifier separator in fallback
  perf test: Adapt test case record+probe_libc_inet_pton.sh for s390
  perf list: Remove s390 specific strcmp_cpuid_cmp function
  perf machine: Set main kernel end address properly

Pull ext4 fixes from Ted Ts'o:
 "Fix misc bugs and a regression for ext4"

* tag 'for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: add MODULE_SOFTDEP to ensure crc32c is included in the initramfs
  ext4: fix bitmap position validation
  ext4: set h_journal if there is a failure starting a reserved handle
  ext4: prevent right-shifting extents beyond EXT_MAX_BLOCKS

The comment claims that this helper will try not to loose bits, but for
64bit long it looses the high bits before hashing 64bit long into 32bit
int.  Use the helper hash_long() to do the right thing for 64bit long.
For 32bit long, there is no change.

All the callers of end_name_hash() either assign the result to
qstr->hash, which is u32 or return the result as an int value (e.g.
full_name_hash()).  Change the helper return type to int to conform to
its users.

[ It took me a while to apply this, because my initial reaction to it
  was - incorrectly - that it could make for slower code.

  After having looked more at it, I take back all my complaints about
  the patch, Amir was right and I was mis-reading things or just being
  stupid.

  I also don't worry too much about the possible performance impact of
  this on 64-bit, since most architectures that actually care about
  performance end up not using this very much (the dcache code is the
  most performance-critical, but the word-at-a-time case uses its own
  hashing anyway).

  So this ends up being mostly used for filesystems that do their own
  degraded hashing (usually because they want a case-insensitive
  comparison function).

  A _tiny_ worry remains, in that not everybody uses DCACHE_WORD_ACCESS,
  and then this potentially makes things more expensive on 64-bit
  architectures with slow or lacking multipliers even for the normal
  case.

  That said, realistically the only such architecture I can think of is
  PA-RISC. Nobody really cares about performance on that, it's more of a
  "look ma, I've got warts^W an odd machine" platform.

  So the patch is fine, and all my initial worries were just misplaced
  from not looking at this properly.   - Linus ]
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>