__bpf_redirect() and act_mirred checks this boolean
to determine whether to prefix an ethernet header.
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ax88772_bind() should return error code immediately when the PHY
was not reset properly through ax88772a_hw_reset().
Otherwise, The asix_get_phyid() will block when get the PHY
Identifier from the PHYSID1 MII registers through asix_mdio_read()
due to the PHY isn't ready. Furthermore, it will produce a lot of
error message cause system crash.As follows:
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to write
 reg index 0x0000: -71
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to send
 software reset: ffffffb9
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to write
 reg index 0x0000: -71
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to enable
 software MII access
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to read
 reg index 0x0000: -71
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to write
 reg index 0x0000: -71
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to enable
 software MII access
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to read
 reg index 0x0000: -71
...
Signed-off-by: Zhang Run <zhang.run@zte.com.cn>
Reviewed-by: Yang Wei <yang.wei9@zte.com.cn>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Following Marvell's acquisition of Cavium, we need to update all the
Cavium drivers maintainer's entries to point to our new e-mail addresses.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ameen Rahman <Ameen.Rahman@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sasha Levin says:

====================
Hyper-V hv_netvsc commits for 5.0

Three patches from Haiyang Zhang to fix settings hash key using ethtool,
and Adrian Vladu's first patch fixing a few spelling mistakes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'linux-can-fixes-for-5.0-20190122' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can

Marc Kleine-Budde says:

====================
pull-request: can 2019-01-22

this is a pull request of 4 patches for net/master.

The first patch by is by Manfred Schlaegl and reverts a patch that caused wrong
warning messages in certain use cases. The next patch is by Oliver Hartkopp for
the bcm that adds sanity checks for the timer value before using it to detect
potential interger overflows. The last two patches are for the flexcan driver,
YueHaibing's patch fixes the the return value in the error path of the
flexcan_setup_stop_mode() function. The second patch is by Uwe Kleine-König and
fixes a NULL pointer deref on older flexcan cores in flexcan_chip_start().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Tariq Toukan says:

====================
mlx4_core fixes for 5.0-rc

This patchset includes two fixes for the mlx4_core driver.

First patch by Aya fixes inaccurate parsing of some FW fields, mistakenly
including additional (mostly reserved) bits.

Second patch by Jack fixes a wrong (yet harmless) error handling of
calls to copy_to_user() during the CQs init stage.

Series generated against net commit:
49a57857 Linux 5.0-rc3
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Procedure mlx4_init_user_cqes() handles returns by copy_to_user
incorrectly. copy_to_user() returns the number of bytes not copied.
Thus, a non-zero return should be treated as a -EFAULT error
(as is done elsewhere in the kernel). However, mlx4_init_user_cqes()
error handling simply returns the number of bytes not copied
(instead of -EFAULT).

Note, though, that this is a harmless bug: procedure mlx4_alloc_cq()
(which is the only caller of mlx4_init_user_cqes()) treats any
non-zero return as an error, but that returned error value is processed
internally, and not passed further up the call stack.

In addition, fixes the following sparse warning:
warning: incorrect type in argument 1 (different address spaces)
   expected void [noderef] <asn:1>*to
   got void *buf

Fixes: e4567897 ("{net, IB}/mlx4: Initialize CQ buffers in the driver when possible")
Reported by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Driver reads the query HCA capabilities without the corresponding masks.
Without the correct masks, the base addresses of the queues are
unaligned.  In addition some reserved bits were wrongly read.  Using the
correct masks, ensures alignment of the base addresses and allows future
firmware versions safe use of the reserved bits.

Fixes: ab9c17a0 ("mlx4_core: Modify driver initialization flow to accommodate SRIOV for Ethernet")
Fixes: 0ff1fb65 ("{NET, IB}/mlx4: Add device managed flow steering firmware API")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now sctp_transport_pmtu() passes transport->saddr into .get_dst() to set
flow sport from 'saddr'. However, transport->saddr is set only when
transport->dst exists in sctp_transport_route().

If sctp_transport_pmtu() is called without transport->saddr set, like
when transport->dst doesn't exists, the flow sport will be set to 0
from transport->saddr, which will cause a wrong route to be got.

Commit 6e91b578 ("sctp: re-use sctp_transport_pmtu in
sctp_transport_route") made the issue be triggered more easily
since sctp_transport_pmtu() would be called in sctp_transport_route()
after that.

In gerneral, fl4->fl4_sport should always be set to
htons(asoc->base.bind_addr.port), unless transport->asoc doesn't exist
in sctp_v4/6_get_dst(), which is the case:

  sctp_ootb_pkt_new() ->
    sctp_transport_route()

For that, we can simply handle it by setting flow sport from saddr only
when it's 0 in sctp_v4/6_get_dst().

Fixes: 6e91b578 ("sctp: re-use sctp_transport_pmtu in sctp_transport_route")
Reported-by: Ying Xu <yinxu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the paths:

  sctp_sf_do_unexpected_init() ->
    sctp_make_init_ack()
  sctp_sf_do_dupcook_a/b()() ->
    sctp_sf_do_5_1D_ce()

The new chunk 'retval' transport is set from the incoming chunk 'chunk'
transport. However, 'retval' transport belong to the new asoc, which
is a different one from 'chunk' transport's asoc.

It will cause that the 'retval' chunk gets set with a wrong transport.
Later when sending it and because of Commit b9fd6839 ("sctp: add
sctp_packet_singleton"), sctp_packet_singleton() will set some fields,
like vtag to 'retval' chunk from that wrong transport's asoc.

This patch is to fix it by setting 'retval' transport correctly which
belongs to the right asoc in sctp_make_init_ack() and
sctp_sf_do_5_1D_ce().

Fixes: b9fd6839 ("sctp: add sctp_packet_singleton")
Reported-by: Ying Xu <yinxu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is to improve sctp stream adding events in 2 places:

  1. In sctp_process_strreset_addstrm_out(), move up SCTP_MAX_STREAM
     and in stream allocation failure checks, as the adding has to
     succeed after reconf_timer stops for the in stream adding
     request retransmission.

  3. In sctp_process_strreset_addstrm_in(), no event should be sent,
     as no in or out stream is added here.

Fixes: 50a41591 ("sctp: implement receiver-side procedures for the Add Outgoing Streams Request Parameter")
Fixes: c5c4ebb3 ("sctp: implement receiver-side procedures for the Add Incoming Streams Request Parameter")
Reported-by: Ying Xu <yinxu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is to improve sctp stream reset events in 4 places:

  1. In sctp_process_strreset_outreq(), the flag should always be set with
     SCTP_STREAM_RESET_INCOMING_SSN instead of OUTGOING, as receiver's in
     stream is reset here.
  2. In sctp_process_strreset_outreq(), move up SCTP_STRRESET_ERR_WRONG_SSN
     check, as the reset has to succeed after reconf_timer stops for the
     in stream reset request retransmission.
  3. In sctp_process_strreset_inreq(), no event should be sent, as no in
     or out stream is reset here.
  4. In sctp_process_strreset_resp(), SCTP_STREAM_RESET_INCOMING_SSN or
     OUTGOING event should always be sent for stream reset requests, no
     matter it fails or succeeds to process the request.

Fixes: 81054476 ("sctp: implement receiver-side procedures for the Outgoing SSN Reset Request Parameter")
Fixes: 16e1a919 ("sctp: implement receiver-side procedures for the Incoming SSN Reset Request Parameter")
Fixes: 11ae76e6 ("sctp: implement receiver-side procedures for the Reconf Response Parameter")
Reported-by: Ying Xu <yinxu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ip l add dev tun type gretap key 1000
ip a a dev tun 10.0.0.1/24

Packets with tun-id 1000 can be recived by tun dev. But packet can't
be sent through dev tun for non-tunnel-dst

With this patch: tunnel-dst can be get through lwtunnel like beflow:
ip r a 10.0.0.7 encap ip dst 172.168.0.11 dev tun
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

syzbot found that ax25 routes where not properly protected
against concurrent use [1].

In this particular report the bug happened while
copying ax25->digipeat.

Fix this problem by making sure we call ax25_get_route()
while ax25_route_lock is held, so that no modification
could happen while using the route.

The current two ax25_get_route() callers do not sleep,
so this change should be fine.

Once we do that, ax25_get_route() no longer needs to
grab a reference on the found route.

[1]
ax25_connect(): syz-executor0 uses autobind, please contact jreuter@yaina.de
BUG: KASAN: use-after-free in memcpy include/linux/string.h:352 [inline]
BUG: KASAN: use-after-free in kmemdup+0x42/0x60 mm/util.c:113
Read of size 66 at addr ffff888066641a80 by task syz-executor2/531

ax25_connect(): syz-executor0 uses autobind, please contact jreuter@yaina.de
CPU: 1 PID: 531 Comm: syz-executor2 Not tainted 5.0.0-rc2+ #10
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0x1db/0x2d0 lib/dump_stack.c:113
 print_address_description.cold+0x7c/0x20d mm/kasan/report.c:187
 kasan_report.cold+0x1b/0x40 mm/kasan/report.c:317
 check_memory_region_inline mm/kasan/generic.c:185 [inline]
 check_memory_region+0x123/0x190 mm/kasan/generic.c:191
 memcpy+0x24/0x50 mm/kasan/common.c:130
 memcpy include/linux/string.h:352 [inline]
 kmemdup+0x42/0x60 mm/util.c:113
 kmemdup include/linux/string.h:425 [inline]
 ax25_rt_autobind+0x25d/0x750 net/ax25/ax25_route.c:424
 ax25_connect.cold+0x30/0xa4 net/ax25/af_ax25.c:1224
 __sys_connect+0x357/0x490 net/socket.c:1664
 __do_sys_connect net/socket.c:1675 [inline]
 __se_sys_connect net/socket.c:1672 [inline]
 __x64_sys_connect+0x73/0xb0 net/socket.c:1672
 do_syscall_64+0x1a3/0x800 arch/x86/entry/common.c:290
 entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x458099
Code: 6d b7 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 3b b7 fb ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007f870ee22c78 EFLAGS: 00000246 ORIG_RAX: 000000000000002a
RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 0000000000458099
RDX: 0000000000000048 RSI: 0000000020000080 RDI: 0000000000000005
RBP: 000000000073bf00 R08: 0000000000000000 R09: 0000000000000000
ax25_connect(): syz-executor4 uses autobind, please contact jreuter@yaina.de
R10: 0000000000000000 R11: 0000000000000246 R12: 00007f870ee236d4
R13: 00000000004be48e R14: 00000000004ce9a8 R15: 00000000ffffffff

Allocated by task 526:
 save_stack+0x45/0xd0 mm/kasan/common.c:73
 set_track mm/kasan/common.c:85 [inline]
 __kasan_kmalloc mm/kasan/common.c:496 [inline]
 __kasan_kmalloc.constprop.0+0xcf/0xe0 mm/kasan/common.c:469
 kasan_kmalloc+0x9/0x10 mm/kasan/common.c:504
ax25_connect(): syz-executor5 uses autobind, please contact jreuter@yaina.de
 kmem_cache_alloc_trace+0x151/0x760 mm/slab.c:3609
 kmalloc include/linux/slab.h:545 [inline]
 ax25_rt_add net/ax25/ax25_route.c:95 [inline]
 ax25_rt_ioctl+0x3b9/0x1270 net/ax25/ax25_route.c:233
 ax25_ioctl+0x322/0x10b0 net/ax25/af_ax25.c:1763
 sock_do_ioctl+0xe2/0x400 net/socket.c:950
 sock_ioctl+0x32f/0x6c0 net/socket.c:1074
 vfs_ioctl fs/ioctl.c:46 [inline]
 file_ioctl fs/ioctl.c:509 [inline]
 do_vfs_ioctl+0x107b/0x17d0 fs/ioctl.c:696
 ksys_ioctl+0xab/0xd0 fs/ioctl.c:713
 __do_sys_ioctl fs/ioctl.c:720 [inline]
 __se_sys_ioctl fs/ioctl.c:718 [inline]
 __x64_sys_ioctl+0x73/0xb0 fs/ioctl.c:718
 do_syscall_64+0x1a3/0x800 arch/x86/entry/common.c:290
 entry_SYSCALL_64_after_hwframe+0x49/0xbe

ax25_connect(): syz-executor5 uses autobind, please contact jreuter@yaina.de
Freed by task 550:
 save_stack+0x45/0xd0 mm/kasan/common.c:73
 set_track mm/kasan/common.c:85 [inline]
 __kasan_slab_free+0x102/0x150 mm/kasan/common.c:458
 kasan_slab_free+0xe/0x10 mm/kasan/common.c:466
 __cache_free mm/slab.c:3487 [inline]
 kfree+0xcf/0x230 mm/slab.c:3806
 ax25_rt_add net/ax25/ax25_route.c:92 [inline]
 ax25_rt_ioctl+0x304/0x1270 net/ax25/ax25_route.c:233
 ax25_ioctl+0x322/0x10b0 net/ax25/af_ax25.c:1763
 sock_do_ioctl+0xe2/0x400 net/socket.c:950
 sock_ioctl+0x32f/0x6c0 net/socket.c:1074
 vfs_ioctl fs/ioctl.c:46 [inline]
 file_ioctl fs/ioctl.c:509 [inline]
 do_vfs_ioctl+0x107b/0x17d0 fs/ioctl.c:696
 ksys_ioctl+0xab/0xd0 fs/ioctl.c:713
 __do_sys_ioctl fs/ioctl.c:720 [inline]
 __se_sys_ioctl fs/ioctl.c:718 [inline]
 __x64_sys_ioctl+0x73/0xb0 fs/ioctl.c:718
 do_syscall_64+0x1a3/0x800 arch/x86/entry/common.c:290
 entry_SYSCALL_64_after_hwframe+0x49/0xbe

The buggy address belongs to the object at ffff888066641a80
 which belongs to the cache kmalloc-96 of size 96
The buggy address is located 0 bytes inside of
 96-byte region [ffff888066641a80, ffff888066641ae0)
The buggy address belongs to the page:
page:ffffea0001999040 count:1 mapcount:0 mapping:ffff88812c3f04c0 index:0x0
flags: 0x1fffc0000000200(slab)
ax25_connect(): syz-executor4 uses autobind, please contact jreuter@yaina.de
raw: 01fffc0000000200 ffffea0001817948 ffffea0002341dc8 ffff88812c3f04c0
raw: 0000000000000000 ffff888066641000 0000000100000020 0000000000000000
page dumped because: kasan: bad access detected

Memory state around the buggy address:
 ffff888066641980: fb fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc
 ffff888066641a00: 00 00 00 00 00 00 00 00 02 fc fc fc fc fc fc fc
>ffff888066641a80: fb fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc
                   ^
 ffff888066641b00: fb fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc
 ffff888066641b80: 00 00 00 00 00 00 00 00 00 00 00 00 fc fc fc fc
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use a bitmap to keep track of which partition types we've already seen;
 for duplicates, return -EEXIST from efx_ef10_mtd_probe_partition() and
 thus skip adding that partition.
Duplicate partitions occur because of the A/B backup scheme used by newer
 sfc NICs.  Prior to this patch they cause sysfs_warn_dup errors because
 they have the same name, causing us not to expose any MTDs at all.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix all typos from hyperv netvsc code comments.
Signed-off-by: Adrian Vladu <avladu@cloudbasesolutions.com>

Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Sasha Levin <sashal@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "Alessandro Pilotti" <apilotti@cloudbasesolutions.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

Changing mtu, channels, or buffer sizes ops call to netvsc_attach(),
rndis_set_subchannel(), which always reset the hash key to default
value. That will override hash key changed previously. This patch
fixes the problem by save the hash key, then restore it when we re-
add the netvsc device.

Fixes: ff4a4419 ("netvsc: allow get/set of RSS indirection table")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
[sl: fix up subject line]
Signed-off-by: Sasha Levin <sashal@kernel.org>

These assignments occur in multiple places. The patch refactor them
to a function for simplicity. It also puts the struct to heap area
for future expension.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
[sl: fix up subject line]
Signed-off-by: Sasha Levin <sashal@kernel.org>

Hyper-V hosts require us to disable RSS before changing RSS key,
otherwise the changing request will fail. This patch fixes the
coding error.

Fixes: ff4a4419 ("netvsc: allow get/set of RSS indirection table")
Reported-by: Wei Hu <weh@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
[sl: fix up subject line]
Signed-off-by: Sasha Levin <sashal@kernel.org>

EtherAVB may provide a checksum of packet data appended to packet data. In
order to allow this checksum to be received by the host descriptor data
needs to be enlarged by 2 bytes to accommodate the checksum.

In the case of MTU-sized packets without a VLAN tag the
checksum were already accommodated by virtue of the space reserved for the
VLAN tag. However, a packet of MTU-size with a  VLAN tag consumed all
packet data space provided by a descriptor leaving no space for the
trailing checksum.

This was not detected by the driver which incorrectly used the last two
bytes of packet data as the checksum and truncate the packet by two bytes.
This resulted all such packets being dropped.

A work around is to disable RX checksum offload
 # ethtool -K eth0 rx off

This patch resolves this problem by increasing the size available for
packet data in RX descriptors by two bytes.

Tested on R-Car E3 (r8a77990) ES1.0 based Ebisu-4D board

v2
* Use sizeof(__sum16) directly rather than adding a driver-local
  #define for the size of the checksum provided by the hw (2 bytes).

Fixes: 4d86d381 ("ravb: RX checksum offload")
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A few PHY drivers have the GPLv2+ license text. They then either have
a MODULE_LICENSE() of GPLv2 only, or an SPDX tag of GPLv2 only.

Since the license text is much easier to understand than either the
SPDX tag or the MODULE_LICENSE, use it as the definitive source of the
licence, and fixup the others when there are contradictions.

Cc: David Wu <david.wu@rock-chips.com>
Cc: Dongpo Li <lidongpo@hisilicon.com>
Cc: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

According to the device tree binding the phy-supply property is
optional. Use the regulator_get_optional API accordingly. The
code already handles NULL just fine.

This gets rid of the following warning:
  fec 2188000.ethernet: 2188000.ethernet supply phy not found, using dummy regulator
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This message gets logged far too often for how interesting is it.

Most distributions nowadays configure NetworkManager to use randomly
generated MAC addresses for Wi-Fi network scans. The interfaces end up
being periodically brought down for the address change. When they're
subsequently brought back up, the message is logged, eventually flooding
the log.

Perhaps the message is not all that helpful: it seems to be more
interesting to hear when the addrconf actually start, not when it does
not. Let's lower its level.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-By: Thomas Haller <thaller@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The connect_local_phy should return NULL (not negative errno) on
error, since its caller expects it.
Signed-off-by: Atsushi Nemoto <atsushi.nemoto@sord.co.jp>
Acked-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Converted to use "imply" instead of "select" for PTP_1588_CLOCK
driver selecting. This could break the hard dependency between
the PTP clock subsystem and ethernet drivers.
This patch also set "default y" for dpaa2 ptp driver building to
provide user an available ptp clock in default.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Michal Kalderon says:

====================
qed*: Error recovery process

Parity errors might happen in the device's memories due to momentary bit
flips which are caused by radiation.
Errors that are not correctable initiate a process kill event, which blocks
the device access towards the host and the network, and a recovery process
is started in the management FW and in the driver.

This series adds the support of this process in the qed core module and in
the qede driver (patches 2 & 3).
Patch 1 in the series revises the load sequence, to avoid PCI errors that
might be observed during a recovery process.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the error recovery process in the qede driver.
The process includes a partial/customized driver unload and load, which
allows it to look like a short suspend period to the kernel while
preserving the net devices' state.
Signed-off-by: Tomer Tayar <tomer.tayar@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the detection and handling of a parity error ("process kill
event"), including the update of the protocol drivers, and the prevention
of any HW access that will lead to device access towards the host while
recovery is in progress.
It also provides the means for the protocol drivers to trigger a recovery
process on their decision.
Signed-off-by: Tomer Tayar <tomer.tayar@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Initiating final cleanup after an ungraceful driver unload can lead to bad
PCI accesses towards the host.
This patch revises the load sequence so final cleanup is sent while the
internal master enable is cleared, to prevent the host accesses, and clears
the internal error indications just before enabling the internal master
enable.
Signed-off-by: Tomer Tayar <tomer.tayar@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

in6_dump_addrs() returns a positive 1 if there was nothing to dump.
This return value can not be passed as return from inet6_dump_addr()
as is, because it will confuse rtnetlink, resulting in NLMSG_DONE
never getting set:

$ ip addr list dev lo
EOF on netlink
Dump terminated

v2: flip condition to avoid a new goto (DaveA)

Fixes: 7c1e8a38 ("netlink: fixup regression in RTM_GETADDR")
Reported-by: Brendan Galloway <brendan.galloway@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Tested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use ERSPAN key header field as tunnel key in gre_parse_header routine
since ERSPAN protocol sets the key field of the external GRE header to
0 resulting in a tunnel lookup fail in ip6gre_err.
In addition remove key field parsing and pskb_may_pull check in
erspan_rcv and ip6erspan_rcv

Fixes: 5a963eb6 ("ip6_gre: Add ERSPAN native tunnel support")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The recent addition of SPDX license identifiers to the files in
drivers/net/ethernet/sun created a licensing conflict.

The cassini driver files contain a proper license notice:

  * This program is free software; you can redistribute it and/or
  * modify it under the terms of the GNU General Public License as
  * published by the Free Software Foundation; either version 2 of the
  * License, or (at your option) any later version.

but the SPDX change added:

   SPDX-License-Identifier: GPL-2.0

So the file got tagged GPL v2 only while in fact it is licensed under GPL
v2 or later.

It's nice that people care about the SPDX tags, but they need to be more
careful about it. Not everything under (the) sun belongs to ...

Fix up the SPDX identifier and remove the boiler plate text as it is
redundant.

Fixes: c861ef83 ("sun: Add SPDX license tags to Sun network drivers")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Shannon Nelson <shannon.nelson@oracle.com>
Cc: Zhu Yanjun <yanjun.zhu@oracle.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: stable@vger.kernel.org
Acked-by: Shannon Nelson <shannon.lee.nelson@gmail.com>
Reviewed-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit cbffaf7a ("can: flexcan: Always use last mailbox for TX")
introduced a loop letting i run up to (including) ARRAY_SIZE(regs->mb)
and in the body accessed regs->mb[i] which is an out-of-bounds array
access that then resulted in an access to an reserved register area.

Later this was changed by commit 0517961c ("can: flexcan: Add
provision for variable payload size") to iterate a bit differently but
still runs one iteration too much resulting to call

	flexcan_get_mb(priv, priv->mb_count)

which results in a WARN_ON and then a NULL pointer exception. This
only affects devices compatible with "fsl,p1010-flexcan",
"fsl,imx53-flexcan", "fsl,imx35-flexcan", "fsl,imx25-flexcan",
"fsl,imx28-flexcan", so newer i.MX SoCs are not affected.

Fixes: cbffaf7a ("can: flexcan: Always use last mailbox for TX")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: linux-stable <stable@vger.kernel.org> # >= 4.20
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Fix a static code checker warning:
drivers/net/can/flexcan.c:1435 flexcan_setup_stop_mode() warn: passing zero to 'PTR_ERR'

Fixes: de3578c1 ("can: flexcan: add self wakeup support")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Kyungtae Kim detected a potential integer overflow in bcm_[rx|tx]_setup()
when the conversion into ktime multiplies the given value with NSEC_PER_USEC
(1000).

Reference: https://marc.info/?l=linux-can&m=154732118819828&w=2

Add a check for the given tv_usec, so that the value stays below one second.
Additionally limit the tv_sec value to a reasonable value for CAN related
use-cases of 400 days and ensure all values to be positive.
Reported-by: Kyungtae Kim <kt0755@gmail.com>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: linux-stable <stable@vger.kernel.org> # >= 2.6.26
Tested-by: Kyungtae Kim <kt0755@gmail.com>
Acked-by: Andre Naujoks <nautsch2@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch revert commit 7da11ba5
("can: dev: __can_get_echo_skb(): print error message, if trying to echo non existing skb")

After introduction of this change we encountered following new error
message on various i.MX plattforms (flexcan):

| flexcan 53fc8000.can can0: __can_get_echo_skb: BUG! Trying to echo non
| existing skb: can_priv::echo_skb[0]

The introduction of the message was a mistake because
priv->echo_skb[idx] = NULL is a perfectly valid in following case: If
CAN_RAW_LOOPBACK is disabled (setsockopt) in applications, the pkt_type
of the tx skb's given to can_put_echo_skb is set to PACKET_LOOPBACK. In
this case can_put_echo_skb will not set priv->echo_skb[idx]. It is
therefore kept NULL.

As additional argument for revert: The order of check and usage of idx
was changed. idx is used to access an array element before checking it's
boundaries.
Signed-off-by: Manfred Schlaegl <manfred.schlaegl@ginzinger.com>
Fixes: 7da11ba5 ("can: dev: __can_get_echo_skb(): print error message, if trying to echo non existing skb")
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Pull pstore fixes from Kees Cook:

 - Fix console ramoops to show the previous boot logs (Sai Prakash
   Ranjan)

 - Avoid allocation and leak of platform data

* tag 'pstore-v5.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  pstore/ram: Avoid allocation and leak of platform data
  pstore/ram: Fix console ramoops to show the previous boot logs

Pull gcc-plugins fixes from Kees Cook:
 "Fix ARM per-task stack protector plugin under GCC 9 (Ard Biesheuvel)"

* tag 'gcc-plugins-v5.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  gcc-plugins: arm_ssp_per_task_plugin: fix for GCC 9+
  gcc-plugins: arm_ssp_per_task_plugin: sign extend the SP mask

Pull networking fixes from David Miller:

 1) Fix endless loop in nf_tables, from Phil Sutter.

 2) Fix cross namespace ip6_gre tunnel hash list corruption, from
    Olivier Matz.

 3) Don't be too strict in phy_start_aneg() otherwise we might not allow
    restarting auto negotiation. From Heiner Kallweit.

 4) Fix various KMSAN uninitialized value cases in tipc, from Ying Xue.

 5) Memory leak in act_tunnel_key, from Davide Caratti.

 6) Handle chip errata of mv88e6390 PHY, from Andrew Lunn.

 7) Remove linear SKB assumption in fou/fou6, from Eric Dumazet.

 8) Missing udplite rehash callbacks, from Alexey Kodanev.

 9) Log dirty pages properly in vhost, from Jason Wang.

10) Use consume_skb() in neigh_probe() as this is a normal free not a
    drop, from Yang Wei. Likewise in macvlan_process_broadcast().

11) Missing device_del() in mdiobus_register() error paths, from Thomas
    Petazzoni.

12) Fix checksum handling of short packets in mlx5, from Cong Wang.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (96 commits)
  bpf: in __bpf_redirect_no_mac pull mac only if present
  virtio_net: bulk free tx skbs
  net: phy: phy driver features are mandatory
  isdn: avm: Fix string plus integer warning from Clang
  net/mlx5e: Fix cb_ident duplicate in indirect block register
  net/mlx5e: Fix wrong (zero) TX drop counter indication for representor
  net/mlx5e: Fix wrong error code return on FEC query failure
  net/mlx5e: Force CHECKSUM_UNNECESSARY for short ethernet frames
  tools: bpftool: Cleanup license mess
  bpf: fix inner map masking to prevent oob under speculation
  bpf: pull in pkt_sched.h header for tooling to fix bpftool build
  selftests: forwarding: Add a test case for externally learned FDB entries
  selftests: mlxsw: Test FDB offload indication
  mlxsw: spectrum_switchdev: Do not treat static FDB entries as sticky
  net: bridge: Mark FDB entries that were added by user as such
  mlxsw: spectrum_fid: Update dummy FID index
  mlxsw: pci: Return error on PCI reset timeout
  mlxsw: pci: Increase PCI SW reset timeout
  mlxsw: pci: Ring CQ's doorbell before RDQ's
  MAINTAINERS: update email addresses of liquidio driver maintainers
  ...