This patch adds RXQ flow control configurations.
Flow control disabled by default.
Minimum ring size limited to 1024 descriptors.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch enables global flow control in FW and in the phylink validate mask.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The firmware needs to monitor the RX Non-occupied descriptor
bits for flow control to move to XOFF mode.
These bits need to be unmasked to be functional, but they will
not raise interrupts as we leave the RX exception summary
bit in MVPP2_ISR_RX_TX_MASK_REG clear.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Flow Control periodic timer would be used if port in
XOFF to transmit periodic XOFF frames.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

BM pool and RXQ size increased to support Firmware Flow Control.
Minimum depletion thresholds to support FC are 1024 buffers.
BM pool size increased to 2048 to have some 1024 buffers
space between depletion thresholds and BM pool size.

Jumbo frames require a 9888B buffer, so memory requirements
for data buffers increased from 7MB to 24MB.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch add PPv23 version definition.
PPv23 is new packet processor in CP115.
Everything that supported by PPv22, also supported by PPv23.
No functional changes in this stage.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently we have PP2v1 and PP2v2 hw-versions, with some different
handlers depending upon condition hw_version = MVPP21/MVPP22.
In a future there will be also PP2v3. Let's use now the generic
"if equal/notEqual MVPP21" for all cases instead of "if MVPP22".

This patch does not change any functionality.
It is not intended to introduce PP2v3.
It just modifies MVPP21/MVPP22 check-condition
bringing it to generic and unified form correct for new-code
introducing and PP2v3 net-next generation.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds CM3 memory map.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

CM3 SRAM address space will be used for Flow Control configuration.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Patch adds CM3 address space and PPv2.3 description.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In order to support the possibility of per-device event channel
settings (e.g. lateeoi spurious event thresholds) add a xenbus device
pointer to struct irq_info() and modify the related event channel
binding interfaces to take the pointer to the xenbus device as a
parameter instead of the domain id of the other side.

While at it remove the stale prototype of bind_evtchn_to_irq_lateeoi().
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Wei Liu <wei.liu@kernel.org>
Reviewed-by: Paul Durrant <paul@xen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

In case of a common event for rx and tx queue the event should be
regarded to be spurious if no rx and no tx requests are pending.

Unfortunately the condition for testing that is wrong causing to
decide a event being spurious if no rx OR no tx requests are
pending.

Fix that plus using local variables for rx/tx pending indicators in
order to split function calls and if condition.

Fixes: 23025393 ("xen/netback: use lateeoi irq binding")
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Reviewed-by: Wei Liu <wl@xen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The function fib6_walk_continue() cannot return a positive value when
called from register_fib_notifier(), but ignoring causes static analyzer to
generate warnings in users of register_fib_notifier() that try to convert
returned error code to pointer with ERR_PTR(). Handle such case by
explicitly checking for positive error values and converting them to
-EINVAL in fib6_tables_dump().
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Suggested-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'mlx5-for-upstream-2021-02-10' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux

Saeed Mahameed says:

====================
mlx5-for-upstream-2021-02-10

Misc cleanups and trivial fixes for net-next

1) spelling mistakes
2) error path checks fixes
3) unused includes and struct fields cleanup
4) build error when MLX5_ESWITCH=no
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Due to the fact that ic_dev->dev is kept open in ic_close_dev, I had
thought that ic_dev will not be freed either. But that is not the case,
but instead "everybody dies" when ipconfig cleans up, and just the
net_device behind ic_dev->dev remains allocated but not ic_dev itself.

This is a problem because in ic_close_devs, for every net device that
we're about to close, we compare it against the list of lower interfaces
of ic_dev, to figure out whether we should close it or not. But since
ic_dev itself is subject to freeing, this means that at some point in
the middle of the list of ipconfig interfaces, ic_dev will have been
freed, and we would be still attempting to iterate through its list of
lower interfaces while checking whether to bring down the remaining
ipconfig interfaces.

There are multiple ways to avoid the use-after-free: we could delay
freeing ic_dev until the very end (outside the while loop). Or an even
simpler one: we can observe that we don't need ic_dev when iterating
through its lowers, only ic_dev->dev, structure which isn't ever freed.
So, by keeping ic_dev->dev in a variable assigned prior to freeing
ic_dev, we can avoid all use-after-free issues.

Fixes: 46acf7bd ("Revert "net: ipv4: handle DSA enabled master network devices"")
Reported-by: kernel test robot <oliver.sang@intel.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Several years ago these two entries have been added, but it's not clear
why. There's no trace that there has ever been such a chip version, and
not even the r8101 vendor driver knows these id's. So let's disable
detection, and if nobody complains remove them completely later.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Nikolay Aleksandrov says:

====================
bonding: 3ad: support for 200G/400G ports and more verbose warning
xk
We'd like to have proper 200G and 400G support with 3ad bond mode, so we
need to add new definitions for them in order to have separate oper keys,
aggregated bandwidth and proper operation (patches 01 and 02). In
patch 03 Ido changes the code to use pr_err_once instead of
pr_warn_once which would help future detection of unsupported speeds.

v2: patch 03: use pr_err_once instead of WARN_ONCE
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The bond driver needs to be patched to support new ethtool speeds.
Currently it emits a single warning [1] when it encounters an unknown
speed. As evident by the two previous patches, this is not explicit
enough. Instead, promote it to an error.

[1]
bond10: (slave swp1): unknown ethtool speed (200000) for port 1 (set it to 0)

v2:
* Use pr_err_once() instead of WARN_ONCE()
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In order to be able to use 3ad mode with 400G devices we need to extend
the supported speeds.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In order to be able to use 3ad mode with 200G devices we need to extend
the supported speeds.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Bhaskar Upadhaya says:

====================
qede: add netpoll and per-queue coalesce support

This is a followup implementation after series

https://patchwork.kernel.org/project/netdevbpf/cover/1610701570-29496-1-git-send-email-bupadhaya@marvell.com/

Patch 1: Add net poll controller support to transmit kernel printks
         over UDP
Patch 2: QLogic card support multiple queues and each queue can be
         configured with respective coalescing parameters, this patch
         add per queue rx-usecs, tx-usecs coalescing parameters
Patch 3: set default per queue rx-usecs, tx-usecs coalescing parameters and
         preserve coalesce parameters across interface up and down

v3: fixed warnings reported by Dan Carpenter
v2: comments from jakub
 - p1: remove poll_controller ndo and add budget 0 support in qede_poll
 - p3: preserve coalesce parameters across interface up and down
===================
Signed-off-by: David S. Miller <davem@davemloft.net>

Here we do the initialization of coalescing values on load.
per queue coalesce values are also restored across up/down of
ethernet interface.
Signed-off-by: Bhaskar Upadhaya <bupadhaya@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

per queue coalescing allows better and more finegrained control
over interrupt rates.
Signed-off-by: Bhaskar Upadhaya <bupadhaya@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

handle netpoll case when qede_poll is called by
netpoll layer with budget 0
Signed-off-by: Bhaskar Upadhaya <bupadhaya@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, a random stack value is being returned because variable
_ret_ is not properly initialized. This variable is actually not
used anymore and it should be removed.

Fix this by removing all instances of variable ret and return 0.

Fixes: 64749c9c ("net: hns3: remove redundant return value of hns3_uninit_all_ring()")
Addresses-Coverity-ID: 1501700 ("Uninitialized scalar variable")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

plat_dat is initialized by stmmac_probe_config_dt().
So, initialization is not required by priv->plat.
This removes unnecessary initialization and variables.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

It is simpler to make net->net_cookie a plain u64
written once in setup_net() instead of looping
and using atomic64 helpers.

Lorenz Bauer wants to add SO_NETNS_COOKIE socket option
and this patch would makes his patch series simpler.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Lorenz Bauer <lmb@cloudflare.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

So far we don't re-configure WOL-related register bits when waking up
from hibernation. I'm not aware of any problem reports, but better
play safe and call __rtl8169_set_wol() in the resume() path too.
To achieve this move calling __rtl8169_set_wol() to
rtl8169_net_resume() and rename the function to rtl8169_runtime_resume().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Michael Walle says:

====================
net: phy: icplus: cleanups and new features

Cleanup the PHY drivers for IPplus devices and add PHY counters and MDIX
support for the IP101A/G.

Patch 5 adds a model detection based on the behavior of the PHY.
Unfortunately, the IP101A shares the PHY ID with the IP101G. But the latter
provides more features. Try to detect the newer model by accessing the page
selection register. If it is writeable, it is assumed, that it is a IP101G.

With this detection in place, we can now access registers >= 16 in a
correct way on the IP101G; that is by first selecting the correct page.
This might previouly worked, because no one ever set another active page
before booting linux.

The last two patches add the new features.
===================
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement the operations to set desired mode and retrieve the current
mode.

This feature was tested with an IP101G.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The IP101G provides three counters: RX packets, CRC errors and symbol
errors. The error counters can be configured to clear automatically on
read. Unfortunately, this isn't true for the RX packet counter. Because
of this and because the RX packet counter is more likely to overflow,
than the error counters implement only support for the error counters.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Registers >= 16 are paged. Be sure to set the page. It seems this was
working for now, because the default is correct for the registers used
in the driver at the moment. But this will also assume, nobody will
change the page select register before linux is started. The page select
register is _not_ reset with a soft reset of the PHY.

To ease the function reuse between the non-paged register space of the
IP101A and the IP101G, add noop read_page()/write_page() callbacks so
the IP101G functions can also be used for the IP101A.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>

This bit is reserved as 'always-write-1'. While this is not a particular
error, because we are only setting it, guard it by checking the model to
prevent errors in the future.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Unfortunately, the IP101A and IP101G share the same PHY identifier.
While most of the functions are somewhat backwards compatible, there is
for example the APS_EN bit on the IP101A but on the IP101G this bit
reserved. Also, the IP101G has many more functionalities.

Deduce the model by accessing the page select register which - according
to the datasheet - is not available on the IP101A. If this register is
writable, assume we have an IP101G.

Split the combined IP101A/G driver into two separate drivers.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>

The PHY core already resets the PHY before .config_init() if a
.soft_reset() op is registered. Drop the open-coded ip1xx_reset().
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Don't sometimes use the address operator and sometimes not. Drop it and
make the code look uniform.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

According to the datasheet of the IP101A/G there is no revision field
and MII_PHYSID2 always reads as 0x0c54. Use PHY_ID_MATCH_EXACT() then.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simpify the initializations of the structures. There is no functional
change.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

George McCollister says:

====================
add HSR offloading support for DSA switches

Add support for offloading HSR/PRP (IEC 62439-3) tag insertion, tag
removal, forwarding and duplication on DSA switches.
This series adds offloading to the xrs700x DSA driver.

Changes since RFC:
 * Split hsr and dsa patches. (Florian Fainelli)

Changes since v1:
 * Fixed some typos/wording. (Vladimir Oltean)
 * eliminate IFF_HSR and use is_hsr_master instead. (Vladimir Oltean)
 * Make hsr_handle_sup_frame handle skb_std as well (required when offloading)
 * Don't add hsr tag for HSR v0 supervisory frames.
 * Fixed tag insertion offloading for PRP.

Changes since v2:
 * Return -EOPNOTSUPP instead of 0 in dsa_switch_hsr_join and
   dsa_switch_hsr_leave. (Vladimir Oltean)
 * Only allow ports 1 and 2 to be HSR/PRP redundant ports. (Tobias Waldekranz)
 * Set and remove HSR features for both redundant ports. (Vladimir Oltean)
 * Change port_hsr_leave() to return int instead of void.
 * Remove hsr_init_skb() proto argument. (Vladimir Oltean)
===================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add offloading for HSR/PRP (IEC 62439-3) tag insertion, tag removal
forwarding and duplication supported by the xrs7000 series switches.

Only HSR v1 and PRP v1 are supported by the xrs7000 series switches (HSR
v0 is not).
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>