Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem

By default, iwlwifi uses order-1 pages (8 KB) to store incoming frames,
but doesnt say so in skb->truesize.

This makes very possible to exhaust kernel memory since these skb evade
normal socket memory accounting.

As struct ieee80211_hdr is going to be pulled before calling IP stack,
there is no need to use dev_alloc_skb() to reserve NET_SKB_PAD bytes.
alloc_skb() is ok in this driver, allowing more tailroom.

Pull beginning of frame in skb header, in the hope we can reuse order-1
pages in the driver immediately for small frames and reduce their
truesize to the minimum (linear skbs)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Neal Cardwell <ncardwell@google.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

WakeOnLan was broken in this driver because gp->asleep_wol is a 1-bit
bitfield and it was being assigned WAKE_MAGIC, which is (1 << 5).
gp->asleep_wol remains 0 and the machine never wakes up.  Fixed by casting
gp->wake_on_lan to bool.  Tested on an iBook G4.
Signed-off-by: Gerard Lledo <gerard.lledo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp_adv_win_scale default value is 2, meaning we expect a good citizen
skb to have skb->len / skb->truesize ratio of 75% (3/4)

In 2.6 kernels we (mis)accounted for typical MSS=1460 frame :
1536 + 64 + 256 = 1856 'estimated truesize', and 1856 * 3/4 = 1392.
So these skbs were considered as not bloated.

With recent truesize fixes, a typical MSS=1460 frame truesize is now the
more precise :
2048 + 256 = 2304. But 2304 * 3/4 = 1728.
So these skb are not good citizen anymore, because 1460 < 1728

(GRO can escape this problem because it build skbs with a too low
truesize.)

This also means tcp advertises a too optimistic window for a given
allocated rcvspace : When receiving frames, sk_rmem_alloc can hit
sk_rcvbuf limit and we call tcp_prune_queue()/tcp_collapse() too often,
especially when application is slow to drain its receive queue or in
case of losses (netperf is fast, scp is slow). This is a major latency
source.

We should adjust the len/truesize ratio to 50% instead of 75%

This patch :

1) changes tcp_adv_win_scale default to 1 instead of 2

2) increase tcp_rmem[2] limit from 4MB to 6MB to take into account
better truesize tracking and to allow autotuning tcp receive window to
reach same value than before. Note that same amount of kernel memory is
consumed compared to 2.6 kernels.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

l2tp_ip_sendmsg could return without releasing socket lock, making it all the
way to userspace, and generating the following warning:

[  130.891594] ================================================
[  130.894569] [ BUG: lock held when returning to user space! ]
[  130.897257] 3.4.0-rc5-next-20120501-sasha #104 Tainted: G        W
[  130.900336] ------------------------------------------------
[  130.902996] trinity/8384 is leaving the kernel with locks still held!
[  130.906106] 1 lock held by trinity/8384:
[  130.907924]  #0:  (sk_lock-AF_INET){+.+.+.}, at: [<ffffffff82b9503f>] l2tp_ip_sendmsg+0x2f/0x550

Introduced by commit 2f16270f ("l2tp: Fix locking in l2tp_ip.c").
Signed-off-by: Sasha Levin <levinsasha928@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

I just noticed after some recent updates, that the init path for the drop
monitor protocol has a minor error.  drop monitor maintains a per cpu structure,
that gets initalized from a single cpu.  Normally this is fine, as the protocol
isn't in use yet, but I recently made a change that causes a failed skb
allocation to reschedule itself .  Given the current code, the implication is
that this workqueue reschedule will take place on the wrong cpu.  If drop
monitor is used early during the boot process, its possible that two cpus will
access a single per-cpu structure in parallel, possibly leading to data
corruption.

This patch fixes the situation, by storing the cpu number that a given instance
of this per-cpu data should be accessed from.  In the case of a need for a
reschedule, the cpu stored in the struct is assigned the rescheule, rather than
the currently executing cpu

Tested successfully by myself.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: David Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

If register_netdev returns failure, the dev->interrupt and
its transfer buffer should be released, so just fix it.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The transfer buffer of dev->interrupt is allocated in .probe path,
but not freed in .disconnet path, so mark the interrupt URB as
URB_FREE_BUFFER to free the buffer when the URB is destroyed.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Creating a VLAN interface on top of ucc_geth adds 4 bytes
to the frame and the HW controller is not prepared to
TX a frame bigger than 1518 bytes which is 4 bytes too
small for a full VLAN frame. Add 16 bytes which will handle
the a simple VLAN and leaves 12 bytes for future expansion.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: David S. Miller <davem@davemloft.net>

In a busy network we see ucc_geth is dropping RX pkgs every now
and then. Increase the RX queues HW descriptors from
16 to 32 to deal with this.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit a844adfd.
The commit a844adfd is degrading rx sensitivity of lower rate in
HT40 mode and it is confirmed that reverting the change is
improving rx sensitivity.

spur_freq_sd (for self-corr in AGC) is defined with respect to the
center of each 20MHz channel while spur_phase_delta (for self-corr
in Rx and spur data filter) is defined with respect to the center
of current RF channel.

So in short, we need to subtract spur_freq_sd (for self-corr in AGC)
by the offset between the center of primary20 and the center of RF
channel in SW. This offset could be +/10 MHz for dynamic 40.

Cc: Madhan Jaganathan <madhanj@qca.qualcomm.com>
Signed-off-by: Kai Shi <kaishi@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

dpc_tl_lock is not acquired in the error handle code for bus down.
But it's unlocked using spin_unlock_irqrestore after finishing task
list walk down. Grab the lock before breaking the loop to avoid a
double unlock.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem

skb_checksum_help(skb) can return an error, we must free skb in this
case. qdisc_drop(skb, sch) can also be feeded with a NULL skb (if
skb_unshare() failed), so lets use this generic helper.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Bug: The VLAN bit of the MAC RX Status Word is unreliable in several older
supported chips. Sometimes the VLAN bit is not set for valid VLAN packets
and also sometimes the VLAN bit is set for non-VLAN packets that came after
a VLAN packet. This results in a receive length error when VLAN hardware
tagging is enabled.

Fix: Variation on original fix proposed by Mirko.
The VLAN information is decoded in the status loop, and can be
applied to the received SKB there. This eliminates the need for the
separate tag field in the interface data structure. The tag has to
be copied and cleared if packet is copied. This version checked out
with vlan and normal traffic.

Note: vlan_tx_tag_present should be renamed vlan_tag_present, but that
is outside scope of this.
Reported-by: Mirko Lindner <mlindner@marvell.com>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a small packet is received, the driver copies it to a new skb to allow
reusing the full size Rx buffer. The copy was propogating the checksum offload
but not the receive hash information. The bug is impact was mostly harmless
and therefore not observed until reviewing this area of code.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

fix kernel doc typos in function names
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver calls cxgb_vlan_mode() from init_one().  This calls into
synchronize_rx(), which locks all the q locks, but the q locks are not
initialized until cxgb_up() -> setup_sge_qsets().  So move the call to
cxgb_vlan_mode() into cxgb_up(), after the call to setup_sge_qsets().
We also move the body of these functions up higher to avoid having to
a forward declaration.

This was found because of the lockdep warning:

    INFO: trying to register non-static key.
    the code is fine but needs lockdep annotation.
    turning off the locking correctness validator.
    Pid: 323, comm: work_for_cpu Not tainted 3.4.0-rc5 #28
    Call Trace:
     [<ffffffff8106e767>] register_lock_class+0x108/0x2d0
     [<ffffffff8106ff42>] __lock_acquire+0xd3/0xd06
     [<ffffffff81070fd0>] lock_acquire+0xbf/0xfe
     [<ffffffff813862a6>] _raw_spin_lock_irq+0x36/0x45
     [<ffffffffa01e71aa>] cxgb_vlan_mode+0x96/0xcb [cxgb3]
     [<ffffffffa01f90eb>] init_one+0x8c4/0x980 [cxgb3]
     [<ffffffff811fcbf0>] local_pci_probe+0x3f/0x70
     [<ffffffff81042206>] do_work_for_cpu+0x10/0x22
     [<ffffffff810482de>] kthread+0xa1/0xa9
     [<ffffffff8138e234>] kernel_thread_helper+0x4/0x10

Contrary to what lockdep says, the code is not fine: we are locking an
uninitialized spinlock.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With the support to bounce buffer added, the skb is coming as nonlinear in the
case of non-DDPed data frames for FCoE, which is mostly ok as the FCoE stack
would take care of that. However, for target mode, we have to set the FC CRC
and FC EOF field to allow the protocol stack to not drop the frame for the last
data frame of that sequence. So fix this by linearizing the skb first before
doing skb_put().
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Marcus Dennis <marcusx.e.dennis@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The driver was freeing memory in shutdown instead of remove.  As a result
we were leaking memory if IEEE DCB was enabled and we loaded/unloaded the
driver.  This change moves the freeing of the memory into the remove
routine where it belongs.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Maybe it's a typo, but it cause that igbvf can't be initialized successfully.
Set perm_addr value using valid dev_addr, although which is equal to hw.mac.addr.
Signed-off-by: Samuel Liao <samuelliao@tencent.com>
Signed-off-by: Shan Wei <davidshan@tencent.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch sets the automatic speed and duplex detection bits
in MAC_CR to enable the mac to determine its speed automatically
from the phy.

Note this must be done BEFORE the receiver or transmitter is
enabled.
Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

also explicitly set the phy to advertise 1000 speeds
Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

smsc75xx phy interrupt acknowledge needs an mdio_write to clear
PHY_INT_SRC instead of just a read like in smsc95xx.
Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

fix bug in phy_init loop that was ignoring BMCR reset bit, akin to smsc95xx's d9460920Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

smsc75xx needs MII_ACCESS_BUSY to be set to correctly trigger mdio I/O.  Note smsc75xx is different from smsc95xx in this regard.
Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes the same issue as reported on smsc95xx, where the
usb device is connected with no ethernet cable plugged-in.

Without this patch sysfs reports the cable as present

flag@flag-desktop:~$ cat /sys/class/net/eth0/carrier
1

while it's not:

flag@flag-desktop:~$ sudo mii-tool eth0
eth0: no link
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

EAP frames for stations in an AP VLAN are sent on the main AP interface
to avoid race conditions wrt. moving stations.
For that to work properly, sta_info_get_bss must be used instead of
sta_info_get when sending EAP packets.
Previously this was only done for cooked monitor injected packets, so
this patch adds a check for tx->skb->protocol to the same place.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When the cwnd reduction is done, ssthresh may be infinite
if TCP enters CWR via ECN or F-RTO. If cwnd is not undone, i.e.,
undo_marker is set, tcp_complete_cwr() falsely set cwnd to the
infinite ssthresh value. The correct operation is to keep cwnd
intact because it has been updated in ECN or F-RTO.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now the helper function from filter.c for negative offsets is exported,
it can be used it in the jit to handle negative offsets.

First modify the asm load helper functions to handle:
- know positive offsets
- know negative offsets
- any offset

then the compiler can be modified to explicitly use these helper
when appropriate.

This fixes the case of a negative X register and allows to lift
the restriction that bpf programs with negative offsets can't
be jited.
Tested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jan Seiffert <kaffeemonster@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Denys Fedoryshchenko reported frequent crashes on a proxy server and kindly
provided a lockdep report that explains it all :

  [  762.903868]
  [  762.903880] =================================
  [  762.903890] [ INFO: inconsistent lock state ]
  [  762.903903] 3.3.4-build-0061 #8 Not tainted
  [  762.904133] ---------------------------------
  [  762.904344] inconsistent {IN-SOFTIRQ-W} -> {SOFTIRQ-ON-W} usage.
  [  762.904542] squid/1603 [HC0[0]:SC0[0]:HE1:SE1] takes:
  [  762.904542]  (key#3){+.?...}, at: [<c0232cc4>]
__percpu_counter_sum+0xd/0x58
  [  762.904542] {IN-SOFTIRQ-W} state was registered at:
  [  762.904542]   [<c0158b84>] __lock_acquire+0x284/0xc26
  [  762.904542]   [<c01598e8>] lock_acquire+0x71/0x85
  [  762.904542]   [<c0349765>] _raw_spin_lock+0x33/0x40
  [  762.904542]   [<c0232c93>] __percpu_counter_add+0x58/0x7c
  [  762.904542]   [<c02cfde1>] sk_clone_lock+0x1e5/0x200
  [  762.904542]   [<c0303ee4>] inet_csk_clone_lock+0xe/0x78
  [  762.904542]   [<c0315778>] tcp_create_openreq_child+0x1b/0x404
  [  762.904542]   [<c031339c>] tcp_v4_syn_recv_sock+0x32/0x1c1
  [  762.904542]   [<c031615a>] tcp_check_req+0x1fd/0x2d7
  [  762.904542]   [<c0313f77>] tcp_v4_do_rcv+0xab/0x194
  [  762.904542]   [<c03153bb>] tcp_v4_rcv+0x3b3/0x5cc
  [  762.904542]   [<c02fc0c4>] ip_local_deliver_finish+0x13a/0x1e9
  [  762.904542]   [<c02fc539>] NF_HOOK.clone.11+0x46/0x4d
  [  762.904542]   [<c02fc652>] ip_local_deliver+0x41/0x45
  [  762.904542]   [<c02fc4d1>] ip_rcv_finish+0x31a/0x33c
  [  762.904542]   [<c02fc539>] NF_HOOK.clone.11+0x46/0x4d
  [  762.904542]   [<c02fc857>] ip_rcv+0x201/0x23e
  [  762.904542]   [<c02daa3a>] __netif_receive_skb+0x319/0x368
  [  762.904542]   [<c02dac07>] netif_receive_skb+0x4e/0x7d
  [  762.904542]   [<c02dacf6>] napi_skb_finish+0x1e/0x34
  [  762.904542]   [<c02db122>] napi_gro_receive+0x20/0x24
  [  762.904542]   [<f85d1743>] e1000_receive_skb+0x3f/0x45 [e1000e]
  [  762.904542]   [<f85d3464>] e1000_clean_rx_irq+0x1f9/0x284 [e1000e]
  [  762.904542]   [<f85d3926>] e1000_clean+0x62/0x1f4 [e1000e]
  [  762.904542]   [<c02db228>] net_rx_action+0x90/0x160
  [  762.904542]   [<c012a445>] __do_softirq+0x7b/0x118
  [  762.904542] irq event stamp: 156915469
  [  762.904542] hardirqs last  enabled at (156915469): [<c019b4f4>]
__slab_alloc.clone.58.clone.63+0xc4/0x2de
  [  762.904542] hardirqs last disabled at (156915468): [<c019b452>]
__slab_alloc.clone.58.clone.63+0x22/0x2de
  [  762.904542] softirqs last  enabled at (156915466): [<c02ce677>]
lock_sock_nested+0x64/0x6c
  [  762.904542] softirqs last disabled at (156915464): [<c0349914>]
_raw_spin_lock_bh+0xe/0x45
  [  762.904542]
  [  762.904542] other info that might help us debug this:
  [  762.904542]  Possible unsafe locking scenario:
  [  762.904542]
  [  762.904542]        CPU0
  [  762.904542]        ----
  [  762.904542]   lock(key#3);
  [  762.904542]   <Interrupt>
  [  762.904542]     lock(key#3);
  [  762.904542]
  [  762.904542]  *** DEADLOCK ***
  [  762.904542]
  [  762.904542] 1 lock held by squid/1603:
  [  762.904542]  #0:  (sk_lock-AF_INET){+.+.+.}, at: [<c03055c0>]
lock_sock+0xa/0xc
  [  762.904542]
  [  762.904542] stack backtrace:
  [  762.904542] Pid: 1603, comm: squid Not tainted 3.3.4-build-0061 #8
  [  762.904542] Call Trace:
  [  762.904542]  [<c0347b73>] ? printk+0x18/0x1d
  [  762.904542]  [<c015873a>] valid_state+0x1f6/0x201
  [  762.904542]  [<c0158816>] mark_lock+0xd1/0x1bb
  [  762.904542]  [<c015876b>] ? mark_lock+0x26/0x1bb
  [  762.904542]  [<c015805d>] ? check_usage_forwards+0x77/0x77
  [  762.904542]  [<c0158bf8>] __lock_acquire+0x2f8/0xc26
  [  762.904542]  [<c0159b8e>] ? mark_held_locks+0x5d/0x7b
  [  762.904542]  [<c0159cf6>] ? trace_hardirqs_on+0xb/0xd
  [  762.904542]  [<c0158dd4>] ? __lock_acquire+0x4d4/0xc26
  [  762.904542]  [<c01598e8>] lock_acquire+0x71/0x85
  [  762.904542]  [<c0232cc4>] ? __percpu_counter_sum+0xd/0x58
  [  762.904542]  [<c0349765>] _raw_spin_lock+0x33/0x40
  [  762.904542]  [<c0232cc4>] ? __percpu_counter_sum+0xd/0x58
  [  762.904542]  [<c0232cc4>] __percpu_counter_sum+0xd/0x58
  [  762.904542]  [<c02cebc4>] __sk_mem_schedule+0xdd/0x1c7
  [  762.904542]  [<c02d178d>] ? __alloc_skb+0x76/0x100
  [  762.904542]  [<c0305e8e>] sk_wmem_schedule+0x21/0x2d
  [  762.904542]  [<c0306370>] sk_stream_alloc_skb+0x42/0xaa
  [  762.904542]  [<c0306567>] tcp_sendmsg+0x18f/0x68b
  [  762.904542]  [<c031f3dc>] ? ip_fast_csum+0x30/0x30
  [  762.904542]  [<c0320193>] inet_sendmsg+0x53/0x5a
  [  762.904542]  [<c02cb633>] sock_aio_write+0xd2/0xda
  [  762.904542]  [<c015876b>] ? mark_lock+0x26/0x1bb
  [  762.904542]  [<c01a1017>] do_sync_write+0x9f/0xd9
  [  762.904542]  [<c01a2111>] ? file_free_rcu+0x2f/0x2f
  [  762.904542]  [<c01a17a1>] vfs_write+0x8f/0xab
  [  762.904542]  [<c01a284d>] ? fget_light+0x75/0x7c
  [  762.904542]  [<c01a1900>] sys_write+0x3d/0x5e
  [  762.904542]  [<c0349ec9>] syscall_call+0x7/0xb
  [  762.904542]  [<c0340000>] ? rp_sidt+0x41/0x83

Bug is that sk_sockets_allocated_read_positive() calls
percpu_counter_sum_positive() without BH being disabled.

This bug was added in commit 180d8cd9
(foundations of per-cgroup memory pressure controlling.), since previous
code was using percpu_counter_read_positive() which is IRQ safe.

In __sk_mem_schedule() we dont need the precise count of allocated
sockets and can revert to previous behavior.
Reported-by: Denys Fedoryshchenko <denys@visp.net.lb>
Sined-off-by: Eric Dumazet <edumazet@google.com>
Cc: Glauber Costa <glommer@parallels.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current checking always succeeded. We have to check the first
character of the string to check that it's empty, thus, skipping
the timeout path.

This fixes the use of the CT target without the timeout option.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Change order of init so netns init is ready
when register ioctl and netlink.

Ver2
	Whitespace fixes and __init added.
Reported-by: "Ryan O'Hara" <rohara@redhat.com>
Signed-off-by: Hans Schillstrom <hans.schillstrom@ericsson.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Simon Horman <horms@verge.net.au>

ip_vs_create_timeout_table() can return NULL
All functions protocol init_netns is affected of this patch.
Signed-off-by: Hans Schillstrom <hans.schillstrom@ericsson.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>

Avoid crash when registering shedulers after
the IPVS core initialization for netns fails. Do this by
checking for present core (net->ipvs).
Signed-off-by: Hans Schillstrom <hans.schillstrom@ericsson.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>

Eric Dumazet pointed out to me that the drop_monitor protocol has some holes in
its smp protections.  Specifically, its possible to replace data->skb while its
being written.  This patch corrects that by making data->skb an rcu protected
variable.  That will prevent it from being overwritten while a tracepoint is
modifying it.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: David Miller <davem@davemloft.net>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Eric Dumazet pointed out this warning in the drop_monitor protocol to me:

[   38.352571] BUG: sleeping function called from invalid context at kernel/mutex.c:85
[   38.352576] in_atomic(): 1, irqs_disabled(): 0, pid: 4415, name: dropwatch
[   38.352580] Pid: 4415, comm: dropwatch Not tainted 3.4.0-rc2+ #71
[   38.352582] Call Trace:
[   38.352592]  [<ffffffff8153aaf0>] ? trace_napi_poll_hit+0xd0/0xd0
[   38.352599]  [<ffffffff81063f2a>] __might_sleep+0xca/0xf0
[   38.352606]  [<ffffffff81655b16>] mutex_lock+0x26/0x50
[   38.352610]  [<ffffffff8153aaf0>] ? trace_napi_poll_hit+0xd0/0xd0
[   38.352616]  [<ffffffff810b72d9>] tracepoint_probe_register+0x29/0x90
[   38.352621]  [<ffffffff8153a585>] set_all_monitor_traces+0x105/0x170
[   38.352625]  [<ffffffff8153a8ca>] net_dm_cmd_trace+0x2a/0x40
[   38.352630]  [<ffffffff8154a81a>] genl_rcv_msg+0x21a/0x2b0
[   38.352636]  [<ffffffff810f8029>] ? zone_statistics+0x99/0xc0
[   38.352640]  [<ffffffff8154a600>] ? genl_rcv+0x30/0x30
[   38.352645]  [<ffffffff8154a059>] netlink_rcv_skb+0xa9/0xd0
[   38.352649]  [<ffffffff8154a5f0>] genl_rcv+0x20/0x30
[   38.352653]  [<ffffffff81549a7e>] netlink_unicast+0x1ae/0x1f0
[   38.352658]  [<ffffffff81549d76>] netlink_sendmsg+0x2b6/0x310
[   38.352663]  [<ffffffff8150824f>] sock_sendmsg+0x10f/0x130
[   38.352668]  [<ffffffff8150abe0>] ? move_addr_to_kernel+0x60/0xb0
[   38.352673]  [<ffffffff81515f04>] ? verify_iovec+0x64/0xe0
[   38.352677]  [<ffffffff81509c46>] __sys_sendmsg+0x386/0x390
[   38.352682]  [<ffffffff810ffaf9>] ? handle_mm_fault+0x139/0x210
[   38.352687]  [<ffffffff8165b5bc>] ? do_page_fault+0x1ec/0x4f0
[   38.352693]  [<ffffffff8106ba4d>] ? set_next_entity+0x9d/0xb0
[   38.352699]  [<ffffffff81310b49>] ? tty_ldisc_deref+0x9/0x10
[   38.352703]  [<ffffffff8106d363>] ? pick_next_task_fair+0x63/0x140
[   38.352708]  [<ffffffff8150b8d4>] sys_sendmsg+0x44/0x80
[   38.352713]  [<ffffffff8165f8e2>] system_call_fastpath+0x16/0x1b

It stems from holding a spinlock (trace_state_lock) while attempting to register
or unregister tracepoint hooks, making in_atomic() true in this context, leading
to the warning when the tracepoint calls might_sleep() while its taking a mutex.
Since we only use the trace_state_lock to prevent trace protocol state races, as
well as hardware stat list updates on an rcu write side, we can just convert the
spinlock to a mutex to avoid this problem.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: David Miller <davem@davemloft.net>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>