Live patches are activated by using the 'limit no_reset' option when
performing a devlink dev reload fw_activate operation. These packages
must first be installed on the device in the usual way. For example,
via devlink dev flash or ethtool -f.

The devlink device info has also been enhanced to render stored and
running live patch versions.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The main changes are firmware live patch support and 2 additional FEC
standard counters.

Add the matching FEC counters to ethtool counter array.  Firmware older
than 220 does not return the proper size of the extended RX counters so
we need to cap it at the smaller legacy size.  Otherwise the new FEC
counters may show up with garbage values.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Populate the dump with firmware 'live' coredump data. This includes
the information stored in NVRAM by the firmware exception handler
prior to recovery. Thus, the live dump includes the desired crash
context.

Firmware does not support HWRM calls after RESET_NOTIFY, so there is
no supported way to capture a coredump during the auto dump phase.
Detect this and abort when called from devlink_health_report().
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tools other than 'ethtool -w' may be used to produce a coredump. For
devlink health, such dumps could even be driver initiated in response
to a health event. In these cases, the kernel thread information will
be placed in the coredump record instead.

v2: use min_t() instead of min() to fix the mismatched type warning
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Recent firmware provides coredump and crashdump size info via
DBG_QCFG command. Read the dump sizes from firmware, instead of
computing in the driver. This patch reduces the time taken
to collect the dump via ethtool.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Firmware sets compression flags for each segment, add this information
while filling segment header.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change bnxt_get_coredump() and bnxt_get_coredump_length() to non-static
functions.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The coredump functionality will be used by devlink health. Refactor
these functions that get coredump and coredump length. There is no
functional change, but the following checkpatch warnings were
addressed:

  - strscpy is preferred over strlcpy.
  - sscanf results should be checked, with an additional warning.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add firmware event counters as well as health state severity. In
the unhealthy state, recommend a remedy and inform the user as to
its impact.

Readability of the devlink tool's output is negatively impacted by
adding these fields to the diagnosis. The single line of text, as
rendered by devlink health diagnose, benefits from more terse
descriptions, which can be substituted without loss of clarity, even
in pretty printed JSON mode.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge 'fw' and 'fw_fatal' health reporters.  There is no longer a need
to distinguish between firmware reporters. Only bonafide errors are
reported now and no reports were being generated for the 'fw' reporter.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Firmware resets initiated by the user are not errors and should not
be reported via devlink. Once only unsolicited resets remain, it is no
longer sensible to maintain a separate fw_reset reporter.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The recovery election messages are often mistaken for errors. Improve
the wording to clarify the meaning of these frequent and expected
events. Also, take the first step towards more inclusive language.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The reported parameter value should not take into account the state
of remote drivers. Firmware will reject remote resets as appropriate,
thus it is not strictly necessary to check HOT_RESET_ALLOWED before
attempting to initiate a reset. But we add the check so that we can
provide more intuitive messages when reset is not permitted.

This firmware setting needs to be restored from all functions after
a firmware reset.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Similar to reload driver_reinit, the RTNL lock is held across reload
down and up to prevent interleaving state changes.  But we need to
subsequently release the RTNL lock while waiting for firmware reset
to complete.

Also keep a statistic on fw_activate resets initiated remotely from
other functions.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The RTNL lock must be held between down and up to prevent interleaving
state changes, especially since external state changes might release
and allocate different driver resource subsets that would otherwise
need to be tracked and carefully handled. If the down function fails,
then devlink will not call the corresponding up function, thus the
lock is released in the down error paths.

v2: Don't use devlink_reload_disable() and devlink_reload_enable().
Instead, check that the netdev is not in unregistered state before
proceeding with reload.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-Off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Resource reservations will also need to be reset after FUNC_DRV_UNRGTR
in the following devlink driver_reinit patch. Extract this logic into a
reusable function.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The device info logged during probe will be reused by the devlink
driver_reinit code in a following patch. Extract this logic into
the new bnxt_print_device_info() function. The board index needs
to be saved in the driver context so that the board information
can be retrieved at a later time, outside of the probe function.
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vladimir Oltean says:

====================
Code movement to br_switchdev.c

This is one more refactoring patch set for the Linux bridge, where more
logic that is specific to switchdev is moved into br_switchdev.c, which
is compiled out when CONFIG_NET_SWITCHDEV is disabled.
====================

Link: https://lore.kernel.org/r/20211027162119.2496321-1-vladimir.oltean@nxp.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Rename all recently imported functions in br_switchdev.c to start with a
br_switchdev_* prefix.

br_fdb_replay_one() -> br_switchdev_fdb_replay_one()
br_fdb_replay() -> br_switchdev_fdb_replay()
br_vlan_replay_one() -> br_switchdev_vlan_replay_one()
br_vlan_replay() -> br_switchdev_vlan_replay()
struct br_mdb_complete_info -> struct br_switchdev_mdb_complete_info
br_mdb_complete() -> br_switchdev_mdb_complete()
br_mdb_switchdev_host_port() -> br_switchdev_host_mdb_one()
br_mdb_switchdev_host() -> br_switchdev_host_mdb()
br_mdb_replay_one() -> br_switchdev_mdb_replay_one()
br_mdb_replay() -> br_switchdev_mdb_replay()
br_mdb_queue_one() -> br_switchdev_mdb_queue_one()
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The following functions:

br_mdb_complete
br_switchdev_mdb_populate
br_mdb_replay_one
br_mdb_queue_one
br_mdb_replay
br_mdb_switchdev_host_port
br_mdb_switchdev_host
br_switchdev_mdb_notify

are only accessible from code paths where CONFIG_NET_SWITCHDEV is
enabled. So move them to br_switchdev.c, in order for that code to be
compiled out if that config option is disabled.

Note that br_switchdev.c gets build regardless of whether
CONFIG_BRIDGE_IGMP_SNOOPING is enabled or not, whereas br_mdb.c only got
built when CONFIG_BRIDGE_IGMP_SNOOPING was enabled. So to preserve
correct compilation with CONFIG_BRIDGE_IGMP_SNOOPING being disabled, we
must now place an #ifdef around these functions in br_switchdev.c.
The offending bridge data structures that need this are
br->multicast_lock and br->mdb_list, these are also compiled out of
struct net_bridge when CONFIG_BRIDGE_IGMP_SNOOPING is turned off.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Similar to fdb_notify() and br_switchdev_fdb_notify(), split the
switchdev specific logic from br_mdb_notify() into a different function.
This will be moved later in br_switchdev.c.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

br_vlan_replay() is relevant only if CONFIG_NET_SWITCHDEV is enabled, so
move it to br_switchdev.c.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

br_vlan_replay() needs this, and we're preparing to move it to
br_switchdev.c, which will be compiled regardless of whether or not
CONFIG_BRIDGE_VLAN_FILTERING is enabled.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Ido Schimmel says:

====================
mlxsw: Offload root TBF as port shaper

Petr says:

Egress configuration in an mlxsw deployment would generally have an ETS
qdisc at root, with a number of bands and a priority dispatch between them.
Some of those bands could then have a RED and/or TBF qdiscs attached.

When TBF is used like this, mlxsw configures shaper on a subgroup, which is
the pair of traffic classes (UC + BUM) corresponding to the band where TBF
is installed. This way it is possible to limit traffic on several bands
(subgroups) independently by configuring several TBF qdiscs, each on a
different band.

It is however not possible to limit traffic flowing through the port as
such. The ASIC supports this through port shapers (as opposed to the
abovementioned subgroup shapers). An obvious way to express this as a user
would be to configure a root TBF qdisc, and then add the whole ETS
hierarchy as its child.

TBF (and RED) can currently be used as a root qdisc. This usage has always
been accepted as a special case, when only one subgroup is configured, and
that is the subgroup that root TBF and RED configure. However it was never
possible to install ETS under that TBF.

In this patchset, this limitation is relaxed. TBF qdisc in root position is
now always offloaded as a port shaper. Such TBF qdisc does not limit
offload of further children. It is thus possible to configure the usual
priority classification through ETS, with RED and/or TBF on individual
bands, all that below a port-level TBF. For example:

    (1) # tc qdisc replace dev swp1 root handle 1: tbf rate 800mbit burst 16kb limit 1M
    (2) # tc qdisc replace dev swp1 parent 1:1 handle 11: ets strict 8 priomap 7 6 5 4 3 2 1 0
    (3) # tc qdisc replace dev swp1 parent 11:1 handle 111: tbf rate 600mbit burst 16kb limit 1M
    (4) # tc qdisc replace dev swp1 parent 11:2 handle 112: tbf rate 600mbit burst 16kb limit 1M

Here, (1) configures a 800-Mbps port shaper, (2) adds an ETS element with 8
strictly-prioritized bands, and (3) and (4) configure two more shapers,
each 600 Mbps, one under 11:1 (band 0, TCs 7 and 15), one under 11:2 (band
1, TCs 6 and 14). This way, traffic on bands 0 and 1 are each independently
capped at 600 Mbps, and at the same time, traffic through the port as a
whole is capped at 800 Mbps.

In patch #1, TBF is permitted as root qdisc, under which the usual qdisc
tree can be installed.

In patch #2, the qdisc offloadability selftest is extended to cover the
root TBF as well.

Patch #3 then tests that the offloaded TBF shapes as expected.
====================

Link: https://lore.kernel.org/r/20211027152001.1320496-1-idosch@idosch.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

TBF can be used as a root qdisc, in which case it is supposed to configure
port shaper. Add a test that verifies that this is so by installing a root
TBF with a ETS or PRIO below it, and then expecting individual bands to all
be shaped according to the root TBF configuration.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

TBF can be used as a root qdisc, with the usual ETS/RED/TBF hierarchy below
it. This use should now be offloaded. Add a test that verifies that it is.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The Spectrum ASIC allows configuration of maximum shaper on all levels of
the scheduling hierarchy: TCs, subgroups, groups and also ports. Currently,
TBF always configures a subgroup. But a user could reasonably express the
intent to configure port shaper by putting TBF to a root position, around
ETS / PRIO. Accept this usage and offload appropriately.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

include/net/sock.h
  7b50ecfc ("net: Rename ->stream_memory_read to ->sock_is_readable")
  4c1e34c0 ("vsock: Enable y2038 safe timeval for timeout")

drivers/net/ethernet/marvell/octeontx2/af/rvu_debugfs.c
  0daa55d0 ("octeontx2-af: cn10k: debugfs for dumping LMTST map table")
  e77bcdd1 ("octeontx2-af: Display all enabled PF VF rsrc_alloc entries.")

Adjacent code addition in both cases, keep both.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Pull networking fixes from Jakub Kicinski:
 "Including fixes from WiFi (mac80211), and BPF.

  Current release - regressions:

   - skb_expand_head: adjust skb->truesize to fix socket memory
     accounting

   - mptcp: fix corrupt receiver key in MPC + data + checksum

  Previous releases - regressions:

   - multicast: calculate csum of looped-back and forwarded packets

   - cgroup: fix memory leak caused by missing cgroup_bpf_offline

   - cfg80211: fix management registrations locking, prevent list
     corruption

   - cfg80211: correct false positive in bridge/4addr mode check

   - tcp_bpf: fix race in the tcp_bpf_send_verdict resulting in reusing
     previous verdict

  Previous releases - always broken:

   - sctp: enhancements for the verification tag, prevent attackers from
     killing SCTP sessions

   - tipc: fix size validations for the MSG_CRYPTO type

   - mac80211: mesh: fix HE operation element length check, prevent out
     of bound access

   - tls: fix sign of socket errors, prevent positive error codes being
     reported from read()/write()

   - cfg80211: scan: extend RCU protection in
     cfg80211_add_nontrans_list()

   - implement ->sock_is_readable() for UDP and AF_UNIX, fix poll() for
     sockets in a BPF sockmap

   - bpf: fix potential race in tail call compatibility check resulting
     in two operations which would make the map incompatible succeeding

   - bpf: prevent increasing bpf_jit_limit above max

   - bpf: fix error usage of map_fd and fdget() in generic batch update

   - phy: ethtool: lock the phy for consistency of results

   - prevent infinite while loop in skb_tx_hash() when Tx races with
     driver reconfiguring the queue <> traffic class mapping

   - usbnet: fixes for bad HW conjured by syzbot

   - xen: stop tx queues during live migration, prevent UAF

   - net-sysfs: initialize uid and gid before calling
     net_ns_get_ownership

   - mlxsw: prevent Rx stalls under memory pressure"

* tag 'net-5.15-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (67 commits)
  Revert "net: hns3: fix pause config problem after autoneg disabled"
  mptcp: fix corrupt receiver key in MPC + data + checksum
  riscv, bpf: Fix potential NULL dereference
  octeontx2-af: Fix possible null pointer dereference.
  octeontx2-af: Display all enabled PF VF rsrc_alloc entries.
  octeontx2-af: Check whether ipolicers exists
  net: ethernet: microchip: lan743x: Fix skb allocation failure
  net/tls: Fix flipped sign in async_wait.err assignment
  net/tls: Fix flipped sign in tls_err_abort() calls
  net/smc: Correct spelling mistake to TCPF_SYN_RECV
  net/smc: Fix smc_link->llc_testlink_time overflow
  nfp: bpf: relax prog rejection for mtu check through max_pkt_offset
  vmxnet3: do not stop tx queues after netif_device_detach()
  r8169: Add device 10ec:8162 to driver r8169
  ptp: Document the PTP_CLK_MAGIC ioctl number
  usbnet: fix error return code in usbnet_probe()
  net: hns3: adjust string spaces of some parameters of tx bd info in debugfs
  net: hns3: expand buffer len for some debugfs command
  net: hns3: add more string spaces for dumping packets number of queue info in debugfs
  net: hns3: fix data endian problem of some functions of debugfs
  ...

Pull spi fixes from Mark Brown:
 "A couple of final driver specific fixes for v5.15, one fixing
  potential ID collisions between two instances of the Altera driver and
  one making Microwire full duplex mode actually work on pl022"

* tag 'spi-fix-v5.15-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
  spi: spl022: fix Microwire full duplex mode
  spi: altera: Change to dynamic allocation of spi id

Pull regmap fix from Mark Brown:
 "This fixes a potential double free when handling an out of memory
  error inserting a node into an rbtree regcache"

* tag 'regmap-fix-v5.15-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
  regmap: Fix possible double-free in regcache_rbtree_exit()

Pull watchdog fixes from Wim Van Sebroeck:
 "I overlooked Guenters request to sent this upstream earlier, so it's a
  bit late in the release cycle.

  This contains:

   - Revert "watchdog: iTCO_wdt: Account for rebooting on second
     timeout"

   - sbsa: only use 32-bit accessors

   - sbsa: drop unneeded MODULE_ALIAS

   - ixp4xx_wdt: Fix address space warning

   - Fix OMAP watchdog early handling"

* tag 'linux-watchdog-5.15-rc7' of git://www.linux-watchdog.org/linux-watchdog:
  watchdog: Fix OMAP watchdog early handling
  watchdog: ixp4xx_wdt: Fix address space warning
  watchdog: sbsa: drop unneeded MODULE_ALIAS
  watchdog: sbsa: only use 32-bit accessors
  Revert "watchdog: iTCO_wdt: Account for rebooting on second timeout"

Pull tracing fix from Steven Rostedt:
 "Do not WARN when attaching event probe to non-existent event

  If the user tries to attach an event probe (eprobe) to an event that
  does not exist, it will trigger a warning. There's an error check that
  only expects memory issues otherwise it is considered a bug. But
  changes in the code to move around the locking made it that it can
  error out if the user attempts to attach to an event that does not
  exist, returning an -ENODEV. As this path can be caused by user space
  putting in a bad value, do not trigger a WARN"

* tag 'trace-v5.15-rc6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  tracing: Do not warn when connecting eprobe to non existing event

This reverts commit 3bda2e5d.

According to discussion with Andrew as follow:
https://lore.kernel.org/netdev/09eda9fe-196b-006b-6f01-f54e75715961@huawei.com/

HNS3 driver needs to separate pause autoneg from general autoneg, so revert
this incorrect patch.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Link: https://lore.kernel.org/r/20211028140624.53149-1-huangguangbin2@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

using packetdrill it's possible to observe that the receiver key contains
random values when clients transmit MP_CAPABLE with data and checksum (as
specified in RFC8684 §3.1). Fix the layout of mptcp_out_options, to avoid
using the skb extension copy when writing the MP_CAPABLE sub-option.

Fixes: d7b26908 ("mptcp: shrink mptcp_out_options struct")
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/233Reported-by: Poorva Sonparote <psonparo@redhat.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Link: https://lore.kernel.org/r/20211027203855.264600-1-mathew.j.martineau@linux.intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The bpf_jit_binary_free() function requires a non-NULL argument. When
the RISC-V BPF JIT fails to converge in NR_JIT_ITERATIONS steps,
jit_data->header will be NULL, which triggers a NULL
dereference. Avoid this by checking the argument, prior calling the
function.

Fixes: ca6cb544 ("riscv, bpf: Factor common RISC-V JIT code")
Signed-off-by: Björn Töpel <bjorn@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/r/20211028125115.514587-1-bjorn@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Commit 406f42fa ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it go through appropriate helpers.

Even though the current code uses dev->addr_len the we can switch
to eth_hw_addr_set() instead of dev_addr_set(). The netdev is
always allocated by alloc_etherdev_mq() and there are at least two
places which assume Ethernet address:
 - the line below calling eth_hw_addr_random()
 - virtnet_set_mac_address() -> eth_commit_mac_addr_change()
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Link: https://lore.kernel.org/r/20211027152012.3393077-1-kuba@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Reduce extra indirection from devlink_params_*() API. Such change
makes it clear that we can drop devlink->lock from these flows, because
everything is executed when the devlink is not registered yet.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rakesh Babu Saladi says:

====================
RVU Debugfs updates.

Patch 1: Few minor changes such as spelling mistakes, deleting unwanted
characters, etc.
Patch 2: Add debugfs dump for lmtst map table
Patch 3: Add channel and channel mask in debugfs.

Changes made from v2 to v3:
1. In patch 1 moved few lines and submitted those changes as a
different patch to net branch
2. Patch 2 is left unchanged.
3. Patch 3 is left unchanged.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is to dispaly channel and channel_mask for each RX
interface of NPC MCAM rule.
Signed-off-by: Rakesh Babu <rsaladi2@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>