Ensure that we either see that the buffer has write space
in tcp_poll() or that we perform a wakeup from the input
side. Did not run into any actual problem here, but thought
that we should make things explicit.
Signed-off-by: Jason Baron <jbaron@akamai.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Error-Bit on the avalon streaming interface of the
tx-dma-channel was always set. In SGMII configurations
this leads to error-symbols on the PCS and packet-rejection
on the receiver side (e.g. SGMII/1000Base-X connected switch).

This only applies to the tse-configuration with MSGDMA.

This issue was detected and fixed on a custom board with
a direct connection to a Marvell switch in SGMII-PHY-Mode.
(incl. custom patches for SGMII-PCS).

According to the datasheet if ff_tx_err (avalon-streaming)
is set it is forwarded to gm_tx_err. As a result the PCS
is forwarding the error by sending a "/V/"-caracter.
Signed-off-by: Andreas Oetken <ennoerlangen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Minor, use the explicit PORT_DEFAULT_VLAN define instead of 0x07.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

mv88e6xxx_setup_port_common was writing to PORT_DEFAULT_VLAN (port
offset 0x07) instead of PORT_CONTROL_1 (port offset 0x05).

Fixes: cca8b133 ("net: dsa: Use mnemonics rather than register numbers")
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tom Herbert says:

====================
net: Fix "hw csum failure" message flood for ppp tunnel

This patch set addresses bug "Bug 95171 - "hw csum failure" message
flood for ppp tunnel since upgrade to 3.16". The problem is that pppoe
is being used over UDP with UDP checksusm enabled. On receive
checksum conversion turns checksum-unnecessary in checksum-
complete. The PPP receive functions do not properly pull
the checksum over its headers, so that when an encapsulated
checksums is considered the checksum-complete value is incorrect.

This patch adds skb_checksum_complete_unset which can be called
in the receive path in lieu of pulling checksum complete in
layer. This is useful when the packet is being modified (e.g.
decompressed) and the checksum-complete value is no longer
relevant.

In the ppp_receive_frame we call skb_checksum_complete_unset to toss
out checksum-complete. This should eliminate the reported messages.
Alternatively, we could add skb_postpull_rcsum and probably
special case handling for VJ compression if maintaining the
checksum-complete is needed (not clear to me this is worth the
effort).

I haven't tested this since setting up the failure scenario doesn't
seem trivial to configure.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Call checksum_complete_unset in PPP receive to discard checksum-complete
value. PPP does not pull checksum for headers and also modifies packet
as in VJ compression.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This function changes ip_summed to CHECKSUM_NONE if CHECKSUM_COMPLETE
is set. This is called to discard checksum-complete when packet
is being modified and checksum is not pulled for headers in a layer.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A pppoe session is identified by its session ID and MAC address.
Currently pppoe does not check if the received pkg has the correct
MAC address. This is a problem when the eth I/F is in promisc mode
as then any DST MAC address is accepted.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@transmode.se>
Signed-off-by: David S. Miller <davem@davemloft.net>

Initial discussion was:
[FYI] xfrm: Don't lookup sk_policy for timewait sockets

Forwarded frames should not have a socket attached. Especially
tw sockets will lead to panics later-on in the stack.

This was observed with TPROXY assigning a tw socket and broken
policy routing (misconfigured). As a result frame enters
forwarding path instead of input. We cannot solve this in
TPROXY as it cannot know that policy routing is broken.

v2:
Remove useless comment
Signed-off-by: Sebastian Poehn <sebastian.poehn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull IDE update from David Miller:
 "Just one change, getting rid of usage of the deprecated PCI DMA
  interfaces in the IDE drivers"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide:
  ide: remove deprecated use of pci api

Pull networking fixes from David Miller:

 1) Fix verifier memory corruption and other bugs in BPF layer, from
    Alexei Starovoitov.

 2) Add a conservative fix for doing BPF properly in the BPF classifier
    of the packet scheduler on ingress.  Also from Alexei.

 3) The SKB scrubber should not clear out the packet MARK and security
    label, from Herbert Xu.

 4) Fix oops on rmmod in stmmac driver, from Bryan O'Donoghue.

 5) Pause handling is not correct in the stmmac driver because it
    doesn't take into consideration the RX and TX fifo sizes.  From
    Vince Bridgers.

 6) Failure path missing unlock in FOU driver, from Wang Cong.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (44 commits)
  net: dsa: use DEVICE_ATTR_RW to declare temp1_max
  netns: remove BUG_ONs from net_generic()
  IB/ipoib: Fix ndo_get_iflink
  sfc: Fix memcpy() with const destination compiler warning.
  altera tse: Fix network-delays and -retransmissions after high throughput.
  net: remove unused 'dev' argument from netif_needs_gso()
  act_mirred: Fix bogus header when redirecting from VLAN
  inet_diag: fix access to tcp cc information
  tcp: tcp_get_info() should fetch socket fields once
  net: dsa: mv88e6xxx: Add missing initialization in mv88e6xxx_set_port_state()
  skbuff: Do not scrub skb mark within the same name space
  Revert "net: Reset secmark when scrubbing packet"
  bpf: fix two bugs in verification logic when accessing 'ctx' pointer
  bpf: fix bpf helpers to use skb->mac_header relative offsets
  stmmac: Configure Flow Control to work correctly based on rxfifo size
  stmmac: Enable unicast pause frame detect in GMAC Register 6
  stmmac: Read tx-fifo-depth and rx-fifo-depth from the devicetree
  stmmac: Add defines and documentation for enabling flow control
  stmmac: Add properties for transmit and receive fifo sizes
  stmmac: fix oops on rmmod after assigning ip addr
  ...

Pull sparc updates from David Miller:
 "The PowerPC folks have a really nice scalable IOMMU pool allocator
  that we wanted to make use of for sparc.  So here we have a series
  that abstracts out their code into a common layer that anyone can make
  use of.

  Sparc is converted, and the PowerPC folks have reviewed and ACK'd this
  series and plan to convert PowerPC over as well"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  iommu-common: Fix PARISC compile-time warnings
  sparc: Make LDC use common iommu poll management functions
  sparc: Make sparc64 use scalable lib/iommu-common.c functions
  sparc: Break up monolithic iommu table/lock into finer graularity pools and lock

Pull arch/tile updates from Chris Metcalf:
 "These are mostly nohz_full changes, plus a smattering of minor fixes
  (notably a couple for ftrace)"

* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
  tile: nohz: warn if nohz_full uses hypervisor shared cores
  tile: ftrace: fix function_graph tracer issues
  tile: map data region shadow of kernel as R/W
  tile: support CONTEXT_TRACKING and thus NOHZ_FULL
  tile: support arch_irq_work_raise
  arch: tile: fix null pointer dereference on pt_regs pointer
  tile/elf: reorganize notify_exec()
  tile: use si_int instead of si_ptr for compat_siginfo

Since commit da4759c7 (sysfs: Use only return value from is_visible for
the file mode), it is possible to reduce the permissions of a file.

So declare temp1_max with the DEVICE_ATTR_RW macro and remove the write
permission in dsa_hwmon_attrs_visible if set_temp_limit isn't provided.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull MIPS updates from Ralf Baechle:
 "This is the main pull request for MIPS for Linux 4.1.  Most
  noteworthy:

   - Add more Octeon-optimized crypto functions
   - Octeon crypto preemption and locking fixes
   - Little endian support for Octeon
   - Use correct CSR to soft reset Octeons
   - Support LEDs on the Octeon-based DSR-1000N
   - Fix PCI interrupt mapping for the Octeon-based DSR-1000N
   - Mark prom_free_prom_memory() as __init for a number of systems
   - Support for Imagination's Pistachio SOC.  This includes arch and
     CLK bits.  I'd like to merge pinctrl bits later
   - Improve parallelism of csum_partial for certain pipelines
   - Organize DTB files in subdirs like other architectures
   - Implement read_sched_clock for all MIPS platforms other than
     Octeon
   - Massive series of 38 fixes and cleanups for the FPU emulator /
     kernel
   - Further FPU remulator work to support new features.  This sits on a
     separate branch which also has been pulled into the 4.1 KVM branch
   - Clean up and fixes for the SEAD3 eval board; remove unused file
   - Various updates for Netlogic platforms
   - A number of small updates for Loongson 3 platforms
   - Increase the memory limit for ATH79 platforms to 256MB
   - A fair number of fixes and updates for BCM47xx platforms
   - Finish the implementation of XPA support
   - MIPS FDC support.  No, not floppy controller but Fast Debug Channel :)
   - Detect the R16000 used in SGI legacy platforms
   - Fix Kconfig dependencies for the SSB bus support"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (265 commits)
  MIPS: Makefile: Fix MIPS ASE detection code
  MIPS: asm: elf: Set O32 default FPU flags
  MIPS: BCM47XX: Fix detecting Microsoft MN-700 & Asus WL500G
  MIPS: Kconfig: Disable SMP/CPS for 64-bit
  MIPS: Hibernate: flush TLB entries earlier
  MIPS: smp-cps: cpu_set FPU mask if FPU present
  MIPS: lose_fpu(): Disable FPU when MSA enabled
  MIPS: ralink: add missing symbol for RALINK_ILL_ACC
  MIPS: ralink: Fix bad config symbol in PCI makefile.
  SSB: fix Kconfig dependencies
  MIPS: Malta: Detect and fix bad memsize values
  Revert "MIPS: Avoid pipeline stalls on some MIPS32R2 cores."
  MIPS: Octeon: Delete override of cpu_has_mips_r2_exec_hazard.
  MIPS: Fix cpu_has_mips_r2_exec_hazard.
  MIPS: kernel: entry.S: Set correct ISA level for mips_ihb
  MIPS: asm: spinlock: Fix addiu instruction for R10000_LLSC_WAR case
  MIPS: r4kcache: Use correct base register for MIPS R6 cache flushes
  MIPS: Kconfig: Fix typo for the r2-to-r6 emulator kernel parameter
  MIPS: unaligned: Fix regular load/store instruction emulation for EVA
  MIPS: unaligned: Surround load/store macros in do {} while statements
  ...

Pull Xtensa updates from Chris Zankel:

 - fix linker script transformation for .text / .text.fixup

 - wire bpf and execveat syscalls

 - provide __NR_sync_file_range2 instead of __NR_sync_file_range, as
   that's what xtensa uses.

 - make xtfpgs LCD driver functional and configurable.  This fixes
   hardware lockup on KC705/ML605 boot

 - add audio subsystem bits to xtfpga DTS and provide sample KC705
   config with audio features enabled

 - add CY7C67300 USB controller support to XTFPGA

 - fix locking issues in ISS network driver

 - document PIC and MX interrupt distributor device tree bindings

* tag 'xtensa-20150416' of git://github.com/czankel/xtensa-linux:
  xtensa: xtfpga: add CY7C67300 USB controller support
  irqchip: xtensa-pic: xtensa-mx: document DT bindings
  xtensa: ISS: fix locking in TAP network adapter
  xtensa: Fix fix linker script transformation for .text / .text.fixup
  xtensa: provide __NR_sync_file_range2 instead of __NR_sync_file_range
  xtensa: wire bpf and execveat syscalls
  xtensa: xtfpga: fix hardware lockup caused by LCD driver
  xtensa: xtfpga: provide defconfig with audio subsystem
  xtensa: xtfpga: add audio card to xtfpga DTS

Replace occurences of the pci api by appropriate call to the dma api.

A simplified version of the semantic patch that finds this problem is as
follows: (http://coccinelle.lip6.fr)

@deprecated@
idexpression id;
position p;
@@

(
  pci_dma_supported@p ( id, ...)
|
  pci_alloc_consistent@p ( id, ...)
)

@bad1@
idexpression id;
position deprecated.p;
@@
...when != &id->dev
   when != pci_get_drvdata ( id )
   when != pci_enable_device ( id )
(
  pci_dma_supported@p ( id, ...)
|
  pci_alloc_consistent@p ( id, ...)
)

@depends on !bad1@
idexpression id;
expression direction;
position deprecated.p;
@@

(
- pci_dma_supported@p ( id,
+ dma_supported ( &id->dev,
...
+ , GFP_ATOMIC
  )
|
- pci_alloc_consistent@p ( id,
+ dma_alloc_coherent ( &id->dev,
...
+ , GFP_ATOMIC
  )
)
Signed-off-by: Quentin Lambert <lambert.quentin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes warnings due to
- no DMA_ERROR_CODE on PARISC,
- sizeof (unsigned long) == 4 bytes on PARISC.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This inline has ~500 callsites.

On 04/14/2015 08:37 PM, David Miller wrote:
> That BUG_ON() was added 7 years ago, and I don't remember it ever
> triggering or helping us diagnose something, so just remove it and
> keep the function inlined.

On x86 allyesconfig build:

    text     data      bss       dec     hex filename
82447071 22255384 20627456 125329911 77861f7 vmlinux4
82441375 22255384 20627456 125324215 7784bb7 vmlinux5prime
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
CC: Eric W. Biederman <ebiederm@xmission.com>
CC: David S. Miller <davem@davemloft.net>
CC: Jan Engelhardt <jengelh@medozas.de>
CC: Jiri Pirko <jpirko@redhat.com>
CC: linux-kernel@vger.kernel.org
CC: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, iflink of the parent interface was always accessed, even
when interface didn't have a parent and hence we crashed there.

Handle the interface types properly: for a child interface, return
the ifindex of the parent, for parent interface, return its ifindex.

For child devices, make sure to set the parent pointer prior to
invoking register_netdevice(), this allows the new ndo to be called
by the stack immediately after the child device is registered.

Fixes: 5aa7add8 ('infiniband/ipoib: implement ndo_get_iflink')
Reported-by: Honggang Li <honli@redhat.com>
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Honggang Li <honli@redhat.com>
Reviewed-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>+
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/ethernet/sfc/selftest.c: In function ‘efx_iterate_state’:
drivers/net/ethernet/sfc/selftest.c:388:9: warning: passing argument 1 of ‘memcpy’ discards ‘const’ qualifier from pointer target type [-Wdiscarded-array-qualifiers]

This is because the msg[] member of struct efx_loopback_payload
is marked as 'const'.  Remove that.
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix bug which occurs when more than <limit> packets are available during
napi-poll, leading to "delays" and retransmissions on the network.

Check for (count < limit) before checking the get_rx_status in tse_rx-function.
Function get_rx_status is reading from the response-fifo.
If there is currently a response in the fifo,
reading the last byte of the response pops the value from the fifo.
If the limit is checked as second condition
and the limit is reached the fifo is popped but the packet is not processed.
Signed-off-by: Andreas Oetken <ennoerlangen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull block core fix from Jens Axboe:
 "A commit in the previous pull request introduce a regression.  So far
  only observed on qemu-sparc64, but it's a general bug.  Please pull
  this single fix to rectify that, thanks"

[ And it turns out that it's been seen outside of that qemu-sparc64
  case, and is easy to trigger with small number of CPUs and blk-mq
  enabled by default - Linus ]

* 'for-linus' of git://git.kernel.dk/linux-block:
  blk-mq: fix iteration of busy bitmap

Pull ACPICA updates from Rafael Wysocki:
 "This updates the kernel's ACPICA code to upstream revision 20150410
  and adds a fix for a GPE handling regression introduced during the
  3.19 cycle on top of that.

  Included are two stable-candidate bug fixes (one of them fixing a 3.16
  regression), multiple other fixes and a bunch of cleanups.

  Specifics:

   - Fix for a GPE handling regression on Dell Latitude D600 that caused
     GPE signaling to stop working on that machine, which appears to be
     due to a hardware glitch, but it used to work and it can be made
     work again in a relativly straightforward way (Rafael J Wysocki).

   - Fix for a mutex unlock regression related to the handling of ACPI
     tables introduced during the 3.16 development cycle (Octavian
     Purdila).

   - _REV modification to always return 2 which has been done by all
     versions of Windows since NT and the firmware people started to use
     it to distinguish between OSes in their AML and do some silly and
     wrong things on that basis (Bob Moore).

   - Fixes and cleanups related to the acpi_physicall_address data type
     including one stable-candidate fix for an issue occasionally
     occuring on 64-bit machines running 32-bit kernels where using
     offsets provided by the firmware may lead to address overflows (Lv
     Zheng).

   - External() opcode support infrastructure needed for recompiling
     disassembled ACPI tables in some cases including interpreter
     modification to ignore that opcode (Bob Moore).

   - Support for the "Windows 2015" string in _OSI (Bob Moore).

   - GPE debug interface change to return values read from hardware
     registers (Lv Zheng).

   - Removal of the __DATE__ macro usage in tools (Rasmus Villemoes).

   - Assorted minor fixes and cleanups (Lv Zheng, Rickard Strandqvist,
     Bob Moore)"

* tag 'acpica-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
  ACPICA: Store GPE register enable masks upfront
  ACPICA: Update version to 20150410.
  ACPICA: Fix a couple issues with the local printf module.
  ACPICA: Disassembler: Some cleanup of the table dump module.
  ACPICA: iASL: Add support for MSDM ACPI table.
  ACPICA: Update for SLIC ACPI table.
  ACPICA: Add "//" before ascii output of buffers.
  ACPICA: Remove unused internal AML opcode.
  ACPICA: Permanently set _REV to the value '2'.
  ACPICA: Add "Windows 2015" string to _OSI support.
  ACPICA: Add infrastructure for External() opcode.
  ACPICA: iASL: Enhancement for constant folding.
  ACPICA: iASL/Disassembler: Add option to assume table contains valid AML.
  ACPICA: Update AML Debugger global variables.
  ACPICA: Update Resource descriptor dump module.
  ACPICA: Fix a sscanf format string.
  ACPICA: Casting changes around acpi_physical_address/acpi_size.
  ACPICA: Resources: Correct conditional compilation definitions.
  ACPICA: Utilities: Correct conditional compilation definitions.
  ACPICA: Tables: Move an iasl specific table function to iasl source file.
  ...

The "hypervisor shared" cores are ones that the Tilera hypervisor
uses to receive interrupts to manage hypervisor-owned devices.
It's a bad idea to try to use those cores with nohz_full, since
they will get interrupted unpredictably -- and invisibly to Linux
tracing tools, since the interrupts are delivered at a higher
privilege level to the Tilera hypervisor.

Generate a clear warning at boot up that this doesn't end well
for the nohz_full cores in question.
Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com>

- Add support for ARCH_SUPPORTS_FTRACE_OPS
- Replace the instruction in ftrace_call with the bundle {move r10, lr;
jal ftrace_stub}, so that the lr contains the right value after returning
from ftrace_stub.  An alternative fix might be to leave the instruction
in ftrace_call alone when it is being updated with ftrace_stub.
Signed-off-by: Tony Lu <zlu@ezchip.com>
Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com>

This is necessary for things like reading /proc/kcore, doing ftrace,
etc.  It happens by default when using huge pages to map the kernel
data, but not when using small pages.
Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com>

Add the TIF_NOHZ flag appropriately.

Add call to user_exit() on entry to do_work_pending() and on entry
to syscalls via do_syscall_trace_enter(), and also the top of
do_syscall_trace_exit() just because it's done in x86.

Add call to user_enter() at the bottom of do_work_pending() once we
have no more work to do before returning to userspace.

Wrap all the trap code in exception_enter() / exception_exit().
Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>

In commit 04ffcb25 ("net: Add ndo_gso_check") Tom originally
added the 'dev' argument to be able to call ndo_gso_check().

Then later, when generalizing this in commit 5f35227e
("net: Generalize ndo_gso_check to ndo_features_check")
Jesse removed the call to ndo_gso_check() in netif_needs_gso()
by calling the new ndo_features_check() in a different place.
This made the 'dev' argument unused.

Remove the unused argument and go back to the code as before.

Cc: Tom Herbert <therbert@google.com>
Cc: Jesse Gross <jesse@nicira.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When you redirect a VLAN device to any device, you end up with
crap in af_packet on the xmit path because hard_header_len is
not equal to skb->mac_len.  So the redirected packet contains
four extra bytes at the start which then gets interpreted as
part of the MAC address.

This patch fixes this by only pushing skb->mac_len.  We also
need to fix ifb because it tries to undo the pushing done by
act_mirred.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Two different problems are fixed here :

1) inet_sk_diag_fill() might be called without socket lock held.
   icsk->icsk_ca_ops can change under us and module be unloaded.
   -> Access to freed memory.
   Fix this using rcu_read_lock() to prevent module unload.

2) Some TCP Congestion Control modules provide information
   but again this is not safe against icsk->icsk_ca_ops
   change and nla_put() errors were ignored. Some sockets
   could not get the additional info if skb was almost full.

Fix this by returning a status from get_info() handlers and
using rcu protection as well.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp_get_info() can be called without holding socket lock,
so any socket fields can change under us.

Use READ_ONCE() to fetch sk_pacing_rate and sk_max_pacing_rate

Fixes: 977cb0ec ("tcp: add pacing_rate information into tcp_info")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tile includes a hypervisor hook to deliver messages to arbitrary
tiles, so we can use that to raise an interrupt as soon as
possible on our own core.  Unfortunately the Tilera hypervisor
disabled that support on principle in previous releases, but
it will be available in MDE 4.3.4 and later.
Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>

Cppcheck reports the following issue:
[arch/tile/kernel/stack.c:116]: (error) Possible null
  pointer dereference: p

In this case, on reporting on an odd fault, p is set to NULL
and immediately afterwords p is dereferenced iff
!kbt->profile is false.  Rather than doing this check just
return NULL rather than falling through to the potential
null pointer dereference (since the original intentional
outcome would be to return NULL anyhow) for this odd fault
case.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com> [tweaked lightly]

In the future mm->exe_file will be done without mmap_sem
serialization, thus isolate and reorganize the tile elf
code to make the transition easier. Good users will, make
use of the more standard get_mm_exe_file(), requiring only
holding the mmap_sem to read the value, and relying on reference
counting to make sure that the exe file won't dissappear
underneath us.

The visible effects of this patch are:

   o We now take and drop the mmap_sem more often. Instead of
     just in arch_setup_additional_pages(), we also do it in:

     1) get_mm_exe_file()
     2) to get the mm->vm_file and notify the simulator.

    [Note that 1) will disappear once we change the locking
     rules for exe_file.]

   o We avoid getting a free page and doing d_path() while
     holding the mmap_sem. This requires reordering the checks.
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com>

To be compatible with the generic get_compat_sigevent(), the
copy_siginfo_to_user32() and thus copy_siginfo_from_user32()
have to use si_int instead of si_ptr.  Using si_ptr means that
for the case of ILP32 compat code running in big-endian mode,
we would end up copying the high 32 bits of the pointer value
into si_int instead of the desired low 32 bits.
Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>

Commit 889fa31f was a bit too eager in reducing the loop count,
so we ended up missing queues in some configurations. Ensure that
our division rounds up, so that's not the case.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Fixes: 889fa31f ("blk-mq: reduce unnecessary software queue looping")
Signed-off-by: Jens Axboe <axboe@fb.com>

Merge third patchbomb from Andrew Morton:

 - various misc things

 - a couple of lib/ optimisations

 - provide DIV_ROUND_CLOSEST_ULL()

 - checkpatch updates

 - rtc tree

 - befs, nilfs2, hfs, hfsplus, fatfs, adfs, affs, bfs

 - ptrace fixes

 - fork() fixes

 - seccomp cleanups

 - more mmap_sem hold time reductions from Davidlohr

* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (138 commits)
  proc: show locks in /proc/pid/fdinfo/X
  docs: add missing and new /proc/PID/status file entries, fix typos
  drivers/rtc/rtc-at91rm9200.c: make IO endian agnostic
  Documentation/spi/spidev_test.c: fix warning
  drivers/rtc/rtc-s5m.c: allow usage on device type different than main MFD type
  .gitignore: ignore *.tar
  MAINTAINERS: add Mediatek SoC mailing list
  tomoyo: reduce mmap_sem hold for mm->exe_file
  powerpc/oprofile: reduce mmap_sem hold for exe_file
  oprofile: reduce mmap_sem hold for mm->exe_file
  mips: ip32: add platform data hooks to use DS1685 driver
  lib/Kconfig: fix up HAVE_ARCH_BITREVERSE help text
  x86: switch to using asm-generic for seccomp.h
  sparc: switch to using asm-generic for seccomp.h
  powerpc: switch to using asm-generic for seccomp.h
  parisc: switch to using asm-generic for seccomp.h
  mips: switch to using asm-generic for seccomp.h
  microblaze: use asm-generic for seccomp.h
  arm: use asm-generic for seccomp.h
  seccomp: allow COMPAT sigreturn overrides
  ...

Let's show locks which are associated with a file descriptor in
its fdinfo file.

Currently we don't have a reliable way to determine who holds a lock.  We
can find some information in /proc/locks, but PID which is reported there
can be wrong.  For example, a process takes a lock, then forks a child and
dies.  In this case /proc/locks contains the parent pid, which can be
reused by another process.

$ cat /proc/locks
...
6: FLOCK  ADVISORY  WRITE 324 00:13:13431 0 EOF
...

$ ps -C rpcbind
  PID TTY          TIME CMD
  332 ?        00:00:00 rpcbind

$ cat /proc/332/fdinfo/4
pos:	0
flags:	0100000
mnt_id:	22
lock:	1: FLOCK  ADVISORY  WRITE 324 00:13:13431 0 EOF

$ ls -l /proc/332/fd/4
lr-x------ 1 root root 64 Mar  5 14:43 /proc/332/fd/4 -> /run/rpcbind.lock

$ ls -l /proc/324/fd/
total 0
lrwx------ 1 root root 64 Feb 27 14:50 0 -> /dev/pts/0
lrwx------ 1 root root 64 Feb 27 14:50 1 -> /dev/pts/0
lrwx------ 1 root root 64 Feb 27 14:49 2 -> /dev/pts/0

You can see that the process with the 324 pid doesn't hold the lock.

This information is required for proper dumping and restoring file
locks.
Signed-off-by: Andrey Vagin <avagin@openvz.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Acked-by: Jeff Layton <jlayton@poochiereds.net>
Acked-by: "J. Bruce Fields" <bfields@fieldses.org>
Acked-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

docs: add missing and new /proc/PID/status file entries, fix typos
Signed-off-by: Nathan Scott <nathans@redhat.com>
Signed-off-by: Chen Hanxiao <chenhanxiao@cn.fujitsu.com>
Cc: Serge Hallyn <serge.hallyn@canonical.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>