Use gpiod_set_value_cansleep() to support gpiochips which can
sleep like, e.g. I2C GPIO expanders.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240409190910.4707-1-francesco@dolcini.itSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Newer Qualcomm platforms (sm8450+) successfully handle busy state and
send the Command Completion after sending the Busy state. Older devices
have firmware bug and can not continue after sending the CCI_BUSY state,
but the command that leads to CCI_BUSY is already forbidden by the
NO_PARTNER_PDOS quirk.

Follow other UCSI glue drivers and drop special handling for CCI_BUSY
event. Let the UCSI core properly handle this state.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240408-qcom-ucsi-fixes-bis-v1-3-716c145ca4b1@linaro.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The Qualcomm SM8550 (and via a fallback compat SM8650) firmware properly
handles the GET_PDOS command, it sends the CCI_BUSY notification,
and then follows with the CCI_COMMAND_COMPLETE event. Stop using the quirk
for those two platforms.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240408-qcom-ucsi-fixes-bis-v1-2-716c145ca4b1@linaro.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Enable the UCSI_DELAY_DEVICE_PDOS quirk on Qualcomm QCM6490. This
platform also doesn't correctly handle reading PD capabilities until PD
partner is connected.

Fixes: 5da727f7 ("usb: typec: ucsi_glink: enable the UCSI_DELAY_DEVICE_PDOS quirk")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240408-qcom-ucsi-fixes-bis-v1-1-716c145ca4b1@linaro.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The PPM might take time to process a reset. Allow 20ms for the reset to
be processed before reading the CCI.

This should not slow down existing implementations because they would
not set any bits in the CCI after a reset, and would take a 20ms delay
to read the CCI anyway. This change makes the delay explicit, and
reduces a CCI read. Based on the spec, the PPM has 10ms to set busy, so,
20ms seems like a reasonable delay before we read the CCI.
Signed-off-by: Pavan Holla <pholla@chromium.org>
Reviewed-by: Prashant Malani <pmalani@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240409-ucsi-reset-delay-v3-1-8440710b012b@chromium.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The Lenovo Yoga Tablet 2 Pro 1380 model is the exception to the rule that
devices which use the Crystal Cove PMIC without using ACPI for battery and
AC power_supply class support use the USB-phy for charger detection.

Unlike the Lenovo Yoga Tablet 2 830 / 1050 models this model has an extra
LC824206XA Micro USB switch which does the charger detection.

Add a DMI quirk to not set the "linux,phy_charger_detect" property on
the 1380 model. This quirk matches on the BIOS version to differentiate
the 1380 model from the 830 and 1050 models which otherwise have
the same DMI strings.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240406140127.17885-1-hdegoede@redhat.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The function ci_usb_phy_init is already handling the
hw_phymode_configure path which is also only possible after we have
a valid phy. So we move the ci_ulpi_init after the phy initialization
to be really sure to be able to communicate with the ulpi phy.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20240328-chipidea-phy-misc-v1-1-907d9de5d4df@pengutronix.deSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

It is expected that the USB controller works in host mode
to have the USB hub operational.

Remove such unneeded property from the devicetree example.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Link: https://lore.kernel.org/r/20240405195051.945474-1-festevam@gmail.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Document the Microchip USB2412, USB2417, and USB2514 USB hubs.

The existing usb251xb.yaml describes Microchip USB251x hubs that are
connected under I2C bus. Here, the hub is under the USB bus and use
the on-board-hub interface instead.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20240405120147.880933-1-festevam@gmail.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

After pulling the reset pin some phys are not immediately ready. We add
a short delay of at least 10 ms to ensure that the phy can be properly
used.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20240402-phy-misc-v1-1-de5c17f93f17@pengutronix.deSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The incompatible device in my possession has a sticker that says
"F5U002 Rev 2" and "P80453-B", and lsusb identifies it as
"050d:0002 Belkin Components IEEE-1284 Controller". There is a bug
report from 2007 from Michael Trausch who was seeing the exact same
errors that I saw in 2024 trying to use this cable.

Link: https://lore.kernel.org/all/46DE5830.9060401@trausch.us/Signed-off-by: Alex Henrie <alexhenrie24@gmail.com>
Link: https://lore.kernel.org/r/20240326150723.99939-5-alexhenrie24@gmail.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This device is a gray USB parallel port adapter with "F5U002" imprinted
on the plastic and a sticker that says both "F5U002" and "P80453-A".
It's identified in lsusb as "05ab:1001 In-System Design BAYI Printer
Class Support". It's subtly different from the other gray cable I have
that has "F5U002 Rev 2" and "P80453-B" on its sticker and device ID
050d:0002.

The uss720 driver appears to work flawlessly with this device, although
the device evidently does not support ECP.
Signed-off-by: Alex Henrie <alexhenrie24@gmail.com>
Link: https://lore.kernel.org/r/20240326150723.99939-4-alexhenrie24@gmail.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Information about 04b8:0002 and 05ab:0002 is from commit e3cb7bde
("USB: misc: uss720: more vendor/product ID's", 2018-03-20). The rest
are from <http://reboots.g-cipher.net/lcd/>.
Signed-off-by: Alex Henrie <alexhenrie24@gmail.com>
Link: https://lore.kernel.org/r/20240326150723.99939-3-alexhenrie24@gmail.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This avoids a "fix this legacy no-device port driver" warning from
parport_announce_port in drivers/parport/share.c. The parport driver now
requires a pointer to the device struct.
Signed-off-by: Alex Henrie <alexhenrie24@gmail.com>
Acked-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Link: https://lore.kernel.org/r/20240326150723.99939-2-alexhenrie24@gmail.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The Dell quirk from ucsi_acpi.c. The quirk is no longer
necessary as we no longer send lone connector change acks.
Signed-off-by: Christian A. Ehrhardt <lk@c--e.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240327224554.1772525-4-lk@c--e.deSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Some PPM implementation do not like UCSI_ACK_CONNECTOR_CHANGE
without UCSI_ACK_COMMAND_COMPLETE. Moreover, doing this is racy
as it requires sending two UCSI_ACK_CC_CI commands in a row and
the second one will be started with UCSI_CCI_ACK_COMPLETE already
set in CCI.

Bundle the UCSI_ACK_CONNECTOR_CHANGE with the UCSI_ACK_COMMAND_COMPLETE
for the UCSI_GET_CONNECTOR_STATUS command that is sent while
handling a connector change event.
Signed-off-by: Christian A. Ehrhardt <lk@c--e.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240327224554.1772525-3-lk@c--e.deSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In ucsi.h there are flag definitions for the ->flags field
in struct ucsi. Some implementations abuse these bits for
their private ->flags fields e.g. in struct ucsi_acpi.

Move the definitions into the backend implementations that
still need them. While there fix one instance where the flag
name was not converted in a previous change.

No semantic change intended.
Signed-off-by: Christian A. Ehrhardt <lk@c--e.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240327224554.1772525-2-lk@c--e.deSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Now as all UCSI issues have been fixed, enable UCSI subdevice on the
Qualcomm SC8180X platform.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240329-qcom-ucsi-fixes-v2-11-0f5d37ed04db@linaro.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Now as all UCSI issues have been fixed, reenable UCSI subdevice on the
Qualcomm SC8280XP platform.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240329-qcom-ucsi-fixes-v2-10-0f5d37ed04db@linaro.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Enable the UCSI_DELAY_DEVICE_PDOS quirk on anything past sc8180x /
sm8350.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240329-qcom-ucsi-fixes-v2-9-0f5d37ed04db@linaro.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In preparation to adding more quirks, extract quirks to the static
variables and reference them through match->data. Otherwise adding
more quirks will add the table really cumbersome.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240329-qcom-ucsi-fixes-v2-8-0f5d37ed04db@linaro.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Qualcomm firmware doesn't return sane information for device's PDOs
unless the partner is also using a PD mode. On SC8280XP this even
results in the Error bit being set in the UCSI response (with 0 error
status).

Add a quirk to delay reading USB PD capabilities for a device until we
detect a partner in PD mode.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240329-qcom-ucsi-fixes-v2-7-0f5d37ed04db@linaro.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Extract function to read PDOs from the port and set PD capabilities
accordingly.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240329-qcom-ucsi-fixes-v2-6-0f5d37ed04db@linaro.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In a way similar to the previous commit, move
typec_partner_set_usb_power_delivery() to be called after reading the PD
caps. This also removes calls to
usb_power_delivery_unregister_capabilities() from the error path. Keep
all capabilities registered until they are cleared by
ucsi_unregister_partner_pdos().

Fixes: b04e1747 ("usb: typec: ucsi: Register USB Power Delivery Capabilities")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240329-qcom-ucsi-fixes-v2-5-0f5d37ed04db@linaro.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

UCSI driver will attempt to set a USB PD device only if it was able to
read PDOs from the firmware. This results in suboptimal behaviour, since
the PD device will be created anyway. Move calls to
typec_port_set_usb_power_delivery() out of conditional code and call it
after reading capabilities.

Fixes: b04e1747 ("usb: typec: ucsi: Register USB Power Delivery Capabilities")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240329-qcom-ucsi-fixes-v2-4-0f5d37ed04db@linaro.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use typec_partner_usb_power_delivery_register() to register PD device
for Type-C partner so that the PD device is nested under the partner's
device in sysfs.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240329-qcom-ucsi-fixes-v2-3-0f5d37ed04db@linaro.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Reading Partner Source PDOs for the consumer Connectors appears to be
working. Permit getting PDOs in this case in order to populate
capabilities of the connected power supply in the sysfs.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240329-qcom-ucsi-fixes-v2-2-0f5d37ed04db@linaro.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The name and description of the USB_NO_PARTNER_PDOS quirk specifies that
only retrieving PDOS of the attached device is crashing. Retrieving PDOS
of the UCSI device works. Fix the condition to limit the workaround only
to is_partner cases.

Fixes: 1d103d6a ("usb: typec: ucsi: fix UCSI on buggy Qualcomm devices")
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240329-qcom-ucsi-fixes-v2-1-0f5d37ed04db@linaro.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Core in typec_altmode_register_driver() already sets the .owner, so
driver does not need to.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240331091737.19836-3-krzk@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Core in typec_altmode_register_driver() already sets the .owner, so
driver does not need to.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240331091737.19836-2-krzk@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Core in platform_driver_register() already sets the .owner, so driver
does not need to.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240331091737.19836-1-krzk@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The UCSI specification defines some notifications to be optional for the
PPM to support. From these only enable the ones the PPM informs us are
actually supported.
Signed-off-by: Diogo Ivo <diogo.ivo@tecnico.ulisboa.pt>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/yhz7nq622mbg3rqsyvqz632pc756niagpfbnzayfswhzo7esho@vrdtx5c3hjgxSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The driver_desc variable is only used in some configurations:

drivers/usb/gadget/udc/omap_udc.c:113:19: error: unused variable 'driver_desc' [-Werror,-Wunused-const-variable]

Since there is only ever one user of it, just open-code the string in place
and remove the global variable and the macro behind it. This also helps
grep for the MODULE_DESCRIPTION string.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20240403080702.3509288-26-arnd@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

CONFIG_DRM_AUX_BRIDGE depends on CONFIG_OF but that dependency is not
included when CONFIG_TYPEC_MUX_PTN36502 selects it, resulting in a
Kconfig warning when CONFIG_OF is disabled:

  WARNING: unmet direct dependencies detected for DRM_AUX_BRIDGE
    Depends on [n]: HAS_IOMEM [=y] && DRM_BRIDGE [=y] && OF [=n]
    Selected by [m]:
    - TYPEC_MUX_PTN36502 [=m] && USB_SUPPORT [=y] && TYPEC [=m] && I2C [=y] && (DRM [=y] || DRM [=y]=n) && DRM_BRIDGE [=y]

Only select CONFIG_DRM_AUX_BRIDGE when CONFIG_DRM_BRIDGE and CONFIG_OF
are enabled to clear up the warning. This results in no functional
change because prior to the refactoring that introduces this warning,
ptn36502_register_bridge() returned 0 when CONFIG_OF was disabled, which
continues to occur with drm_aux_bridge_register() when
CONFIG_DRM_AUX_BRIDGE is not enabled.

Fixes: 9dc28ea2 ("usb: typec: ptn36502: switch to DRM_AUX_BRIDGE")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20240328-fix-ptn36502-drm_aux_bridge-select-v1-1-85552117e26e@kernel.org
Link: https://lore.kernel.org/r/20240404123534.2708591-1-arnd@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We need the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'kbuild-fixes-v6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild

Pull Kbuild fixes from Masahiro Yamada:

 - Deduplicate Kconfig entries for CONFIG_CXL_PMU

 - Fix unselectable choice entry in MIPS Kconfig, and forbid this
   structure

 - Remove unused include/asm-generic/export.h

 - Fix a NULL pointer dereference bug in modpost

 - Enable -Woverride-init warning consistently with W=1

 - Drop KCSAN flags from *.mod.c files

* tag 'kbuild-fixes-v6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  kconfig: Fix typo HEIGTH to HEIGHT
  Documentation/llvm: Note s390 LLVM=1 support with LLVM 18.1.0 and newer
  kbuild: Disable KCSAN for autogenerated *.mod.c intermediaries
  kbuild: make -Woverride-init warnings more consistent
  modpost: do not make find_tosym() return NULL
  export.h: remove include/asm-generic/export.h
  kconfig: do not reparent the menu inside a choice block
  MIPS: move unselectable FIT_IMAGE_FDT_EPM5 out of the "System type" choice
  cxl: remove CONFIG_CXL_PMU entry in drivers/cxl/Kconfig

Pull EDAC fixes from Borislav Petkov:

 - Fix more issues in the AMD FMPM driver

* tag 'edac_urgent_for_v6.9_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras:
  RAS: Avoid build errors when CONFIG_DEBUG_FS=n
  RAS/AMD/FMPM: Safely handle saved records of various sizes
  RAS/AMD/FMPM: Avoid NULL ptr deref in get_saved_records()

Pull irq fixes from Borislav Petkov:

 - Fix an unused function warning on irqchip/irq-armada-370-xp

 - Fix the IRQ sharing with pinctrl-amd and ACPI OSL

* tag 'irq_urgent_for_v6.9_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/armada-370-xp: Suppress unused-function warning
  genirq: Introduce IRQF_COND_ONESHOT and use it in pinctrl-amd

Pull x86 perf fixes from Borislav Petkov:

 - Define the correct set of default hw events on AMD Zen4

 - Use the correct stalled cycles PMCs on AMD Zen2 and newer

 - Fix detection of the LBR freeze feature on AMD

* tag 'perf_urgent_for_v6.9_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/x86/amd/core: Define a proper ref-cycles event for Zen 4 and later
  perf/x86/amd/core: Update and fix stalled-cycles-* events for Zen 2 and later
  perf/x86/amd/lbr: Use freeze based on availability
  x86/cpufeatures: Add new word for scattered features