The Atom DPCM driver only allowed for the SSP2 interface, add
definitions for modem/SSP0.

These definitions might be used to route audio to a codec
connected to SSP0 (instead of a modem in traditional usages),
but there is a restriction to 2ch I2S. SSP2 is capable of
handling up to 4 slot TDM.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

BYT-CR needs special handling to deal with BIOS issues.
For some reason the IPC interrupt index is also modified from
the Baytrail-T reference.

Use PUNIT BIOS config bits to infer platform details.
Assume regular Baytrail configs if status is incorrect or
CONFIG_IOSF_MBI is not enabled.

SSP0 routing issues are solved without dedicated firmware
in following patches

Tested on Asus T100TA and T100TAF.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Some Baytrail-CR devices rely on analog mics connected with
differential pairs and not the single-ended default
Add quirk and enable it for T00TAF
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Some Baytrail devices only have a mono speaker, add quirk and enable
it for T100TAF.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add quirk based on DMI string matching
Also fix matching to use DMI_EXACT_MATCH otherwise T100TA and T100TAF
will be using same quirk
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Merge branch 'topic/rt5640' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into asoc-intel

Adding missing definitions and flags to select internal
clock source as system clock, needed for jack detection.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Now that we have balanced loading of the topology file and split of init
and fw_init and fill module data during asoc probe.

So remove it from runtime, but keep error check in case things fall apart.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Once topology and firmware are loaded, we can parse the manifest. Use driver
pipe and widget list to get list of all modules and populate the data.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

snd_skl_get_module_info() takes skl_dfw_module as an argument. The users
then updates the topology data, so instead pass skl_module_cfg and let
snd_skl_get_module_info() fill that up.
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Merge branch 'topic/hda-link-time' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound into asoc-intel

The HDA controller from SKL onwards support additional timestamp
reporting of the link time. The link time is read from HW
registers and converted to audio values.
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Signed-off-by: Hardik T Shah <hardik.t.shah@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Skylake onwards HDA controller supports new capabilities like
Global Time Stamping (GTS) capability. So add support to parse
these new capabilities.
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Signed-off-by: Hardik T Shah <hardik.t.shah@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Remove the unused one as we have moved it up to hdac core.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Now that we have the bus parse capabilities moved to core, we need to
convert users.

The SKL driver and HDA extended lib needs to converted in single patch,
otherwise we regress on the functionality.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

HDA capability introduced recently are move to hdac core so that it can
be used by legacy driver as well. Also move the capability pointers up
to hdac_bus object.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

A module can be scheduled in deferent processing domains in DSP. Topology
specifies the module domain.
Signed-off-by: Senthilnathan Veppur <senthilnathanx.veppur@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

While changing code notice bad comment style, so fix it up.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The library load is added as one of the ops in skl_dsp_fw_ops().

The manifest load gives the files to be loaded which are loaded during
the fw_init()
Signed-off-by: Ramesh Babu <ramesh.babu@intel.com>
Signed-off-by: Kranthi G <gudishax.kranthikumar@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

sound/soc/intel/skylake/skl-topology.c:480:24-30: ERROR: application of sizeof to pointer

 sizeof when applied to a pointer typed expression gives the size of
 the pointer

Generated by: scripts/coccinelle/misc/noderef.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

DSP fw can have additional firmwares as libs. These libs can be
loaded using message IPC_GLB_LOAD_LIBRARY.
Signed-off-by: Ramesh Babu <ramesh.babu@intel.com>
Signed-off-by: Kranthi G <gudishax.kranthikumar@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The firmware manifest contains UUIDs which needs to be passed only once.

So use the newly introduced is_first_boot flag to distinguish and parse
these only once on bxt platform as well.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The firmware manifest contains UUIDs which needs to be passed only once.

So use the newly introduced is_first_boot flag to distinguish and parse
these only once.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

For additional library parsing, we need to pass firmware to be
loaded and not use the pointer in context. Also, Library module
IDs are combination of library index and module ID in manifest.

So add the additional arguments of firmware and library offset to
snd_skl_parse_uuids().
Signed-off-by: Senthilnathan Veppur <senthilnathanx.veppur@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Topology manifest gives information about the libraries to be
loaded. Implement the topology manifest load callback to get
this.
Signed-off-by: Kranthi G <gudishax.kranthikumar@intel.com>
Signed-off-by: Senthilnathan Veppur <senthilnathanx.veppur@intel.com>
Signed-off-by: Ramesh Babu <ramesh.babu@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The DSP instance creation also loads the firmware on DSPs. For library load
the firmware names come from topology so can't be loaded at object creation.

So split the firmware load and object creation. FW load is now called after
topology init in platform probe.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

To query the ops used for a platform, we use skl_get_dsp_ops() which return
index and then we load the ops.

Rather than this return the ops, this way it cna be used later to query the
ops in rest of the driver.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Since we are moving DSP init to later, at the topology load the
module info is not available.

So set the module id to -1 at init and query at first module
initialization.
Signed-off-by: Senthilnathan Veppur <senthilnathanx.veppur@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Pull more block fixes from Jens Axboe:
 "As mentioned in the pull the other day, a few more fixes for this
  round, all related to the bio op changes in this series.

  Two fixes, and then a cleanup, renaming bio->bi_rw to bio->bi_opf.  I
  wanted to do that change right after or right before -rc1, so that
  risk of conflict was reduced.  I just rebased the series on top of
  current master, and no new ->bi_rw usage has snuck in"

* 'for-linus' of git://git.kernel.dk/linux-block:
  block: rename bio bi_rw to bi_opf
  target: iblock_execute_sync_cache() should use bio_set_op_attrs()
  mm: make __swap_writepage() use bio_set_op_attrs()
  block/mm: make bdev_ops->rw_page() take a bool for read/write

Pull drm zpos property support from Dave Airlie:
 "This tree was waiting on some media stuff I hadn't had time to get a
  stable branchpoint off, so I just waited until it was all in your tree
  first.

  It's been around a bit on the list and shouldn't affect anything
  outside adding the generic API and moving some ARM drivers to using
  it"

* tag 'drm-for-v4.8-zpos' of git://people.freedesktop.org/~airlied/linux:
  drm: rcar: use generic code for managing zpos plane property
  drm/exynos: use generic code for managing zpos plane property
  drm: sti: use generic zpos for plane
  drm: add generic zpos property

Since commit 63a4cc24, bio->bi_rw contains flags in the lower
portion and the op code in the higher portions. This means that
old code that relies on manually setting bi_rw is most likely
going to be broken. Instead of letting that brokeness linger,
rename the member, to force old and out-of-tree code to break
at compile time instead of at runtime.

No intended functional changes in this commit.
Signed-off-by: Jens Axboe <axboe@fb.com>

The original commit missed this function, it needs to mark it a
write flush.

Cc: Mike Christie <mchristi@redhat.com>
Fixes: e742fc32 ("target: use bio op accessors")
Signed-off-by: Jens Axboe <axboe@fb.com>

Cleaner than manipulating bio->bi_rw flags directly.
Signed-off-by: Jens Axboe <axboe@fb.com>

Commit abf54548 changed it from an 'rw' flags type to the
newer ops based interface, but now we're effectively leaking
some bdev internals to the rest of the kernel. Since we only
care about whether it's a read or a write at that level, just
pass in a bool 'is_write' parameter instead.

Then we can also move op_is_write() and friends back under
CONFIG_BLOCK protection.
Reviewed-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>

Pull documentation fixes from Jonathan Corbet:
 "Three fixes for the docs build, including removing an annoying warning
  on 'make help' if sphinx isn't present"

* tag 'doc-4.8-fixes' of git://git.lwn.net/linux:
  DocBook: use DOCBOOKS="" to ignore DocBooks instead of IGNORE_DOCBOOKS=1
  Documenation: update cgroup's document path
  Documentation/sphinx: do not warn about missing tools in 'make help'

Pull binfmt_misc update from James Bottomley:
 "This update is to allow architecture emulation containers to function
  such that the emulation binary can be housed outside the container
  itself.  The container and fs parts both have acks from relevant
  experts.

  To use the new feature you have to add an F option to your binfmt_misc
  configuration"

From the docs:
 "The usual behaviour of binfmt_misc is to spawn the binary lazily when
  the misc format file is invoked.  However, this doesn't work very well
  in the face of mount namespaces and changeroots, so the F mode opens
  the binary as soon as the emulation is installed and uses the opened
  image to spawn the emulator, meaning it is always available once
  installed, regardless of how the environment changes"

* tag 'binfmt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/binfmt_misc:
  binfmt_misc: add F option description to documentation
  binfmt_misc: add persistent opened binary handler for containers
  fs: add filp_clone_open API

In most cases, EPERM is returned on immutable inode, and there're only a
few places returning EACCES. I noticed this when running LTP on
overlayfs, setxattr03 failed due to unexpected EACCES on immutable
inode.

So converting all EACCES to EPERM on immutable inode.
Acked-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Eryu Guan <guaneryu@gmail.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull more vfs updates from Al Viro:
 "Assorted cleanups and fixes.

  In the "trivial API change" department - ->d_compare() losing 'parent'
  argument"

* 'for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  cachefiles: Fix race between inactivating and culling a cache object
  9p: use clone_fid()
  9p: fix braino introduced in "9p: new helper - v9fs_parent_fid()"
  vfs: make dentry_needs_remove_privs() internal
  vfs: remove file_needs_remove_privs()
  vfs: fix deadlock in file_remove_privs() on overlayfs
  get rid of 'parent' argument of ->d_compare()
  cifs, msdos, vfat, hfs+: don't bother with parent in ->d_compare()
  affs ->d_compare(): don't bother with ->d_inode
  fold _d_rehash() and __d_rehash() together
  fold dentry_rcuwalk_invalidate() into its only remaining caller

Merge tag 'xfs-rmap-for-linus-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs

Pull more xfs updates from Dave Chinner:
 "This is the second part of the XFS updates for this merge cycle, and
  contains the new reverse block mapping feature for XFS.

  Reverse mapping allows us to track the owner of a specific block on
  disk precisely.  It is implemented as a set of btrees (one per
  allocation group) that track the owners of allocated extents.
  Effectively it is a "used space tree" that is updated when we allocate
  or free extents.  i.e. it is coherent with the free space btrees we
  already maintain and never overlaps with them.

  This reverse mapping infrastructure is the building block of several
  upcoming features - reflink, copy-on-write data, dedupe, online
  metadata and data scrubbing, highly accurate bad sector/data loss
  reporting to users, and significantly improved reconstruction of
  damaged and corrupted filesystems.  There's a lot of new stuff coming
  along in the next couple of cycles,a nd it all builds in the rmap
  infrastructure.

  As such, it's a huge chunk of new code with new on-disk format
  features and internal infrastructure.  It warns at mount time as an
  experimental feature and that it may eat data (as we do with all new
  on-disk features until they stabilise).  We have not released
  userspace suport for it yet - userspace support currently requires
  download from Darrick's xfsprogs repo and build from source, so the
  access to this feature is really developer/tester only at this point.
  Initial userspace support will be released at the same time kernel
  with this code in it is released.

  The new rmap enabled code regresses 3 xfstests - all are ENOSPC
  related corner cases, one of which Darrick posted a fix for a few
  hours ago.  The other two are fixed by infrastructure that is part of
  the upcoming reflink patchset.  This new ENOSPC infrastructure
  requires a on-disk format tweak required to keep mount times in
  check - we need to keep an on-disk count of allocated rmapbt blocks so
  we don't have to scan the entire btrees at mount time to count them.

  This is currently being tested and will be part of the fixes sent in
  the next week or two so users will not be exposed to this change"

* tag 'xfs-rmap-for-linus-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs: (52 commits)
  xfs: move (and rename) the deferred bmap-free tracepoints
  xfs: collapse single use static functions
  xfs: remove unnecessary parentheses from log redo item recovery functions
  xfs: remove the extents array from the rmap update done log item
  xfs: in btree_lshift, only allocate temporary cursor when needed
  xfs: remove unnecesary lshift/rshift key initialization
  xfs: remove the get*keys and update_keys btree ops pointers
  xfs: enable the rmap btree functionality
  xfs: don't update rmapbt when fixing agfl
  xfs: disable XFS_IOC_SWAPEXT when rmap btree is enabled
  xfs: add rmap btree block detection to log recovery
  xfs: add rmap btree geometry feature flag
  xfs: propagate bmap updates to rmapbt
  xfs: enable the xfs_defer mechanism to process rmaps to update
  xfs: log rmap intent items
  xfs: create rmap update intent log items
  xfs: add rmap btree insert and delete helpers
  xfs: convert unwritten status of reverse mappings
  xfs: remove an extent from the rmap btree
  xfs: add an extent to the rmap btree
  ...