Merge tag 'renesas-boards-for-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/boards

From Simon Horman:
Renesas ARM-based SoC board updates for v3.11

Highlights:
bockw: add SDHI0 support
bockw: add dummy regulators for SMSC
bockw: Document CN9 SCIF/RCAN dipswitch selection
lager: support GPIO switches and LEDs
kzm9g: add AS3711 PMIC platform data
marzen: Use INTC External IRQ pin driver for SMSC
ape6evm: Update MP clock parent become EXTAL2 in line with changes
         to r8a73a4 SoC code

* tag 'renesas-boards-for-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  ARM: shmobile: marzen: keep local function as static
  ARM: shmobile: bockw: add SDHI0 support
  ARM: shmobile: marzen: Use INTC External IRQ pin driver for SMSC
  ARM: shmobile: lager: support GPIO switches
  ARM: shmobile: lager: Add GPIO LEDs
  ARM: shmobile: bockw: add dummy regulators for SMSC
  ARM: shmobile: bockw: add CN9 SCIF/RCAN selection dipswitch explanation
  ARM: shmobile: kzm9g: add AS3711 PMIC platform data
  ARM: shmobile: kzm9d: resigser smsc911x platform device with id -1
  ARM: shmobile: bockw: define FPGA address and rename iomem variable
  ARM: shmobile: ape6evm: MP clock parent become EXTAL2

Signed-off-by: Olof Johansson <olof@lixom.net>

Conflicts:
	arch/arm/mach-shmobile/Kconfig
	arch/arm/mach-shmobile/include/mach/r8a7778.h
	arch/arm/mach-shmobile/setup-r8a7778.c

Merge tag 'renesas-defconfig-for-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/boards

From Simon Horman:
Renesas ARM based SoC defconfig updates for v3.11

kzm9g: Enable AS3711 PMIC
bockw: Enable, USB, PM_RUNTIME, I2C and SDHI
armadillo800eva: Correct SERIAL_SH_SCI_NR_UARTS

* tag 'renesas-defconfig-for-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  ARM: shmobile: kzm9g: enable AS3711 PMIC in defconfig
  ARM: shmobile: bockw: enable USB in defconfig
  ARM: shmobile: bockw: enable CONFIG_PM_RUNTIME in defconfig
  ARM: shmobile: bockw: enable I2C in defconfig
  ARM: shmobile: bockw: enable SDHI on defconfig
  ARM: shmobile: armadillo800eva: Fix maximum number of SCIF
Signed-off-by: Olof Johansson <olof@lixom.net>

marzen_init_late() should be static
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This patch is directly accessing to PUPR4 register which can
control SDHI0 CD/WP pin pull-up setting.
It should be replaced in the future.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Update the marzen board to use the INTC External IRQ pin driver for SMSC.

This code was originally posted by Magnus Damm as part of
"ARM: shmobile: INTC External IRQ pin driver on r8a7779"
but somehow omitted when I applied that patch.

Cc: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The lager board has pins 1 - 4 of SW2 wired up to GPIO pins.
This patch allows access to those pins as KEYS 1 - 4 using
gpio-keys.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The board has 3 LEDs connected to GPIOs. Add a led-gpio device to
support them.

Based on "ARM: shmobile: marzen: Add GPIO LEDs" by Laurent Pinchart.

Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

SMSC driver will try to get regulator if .config had CONFIG_REGULATOR,
and, shmobile_defconfig has it.
SMSC driver on Bock-W board will be failed if it doens't have
dummy regulator settings.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Debug serial (= SCIF0) is connected to CN9 upper side,
and it is shared by RCAN.
This patch adds SCIF/RCAN dipswitch explanation on
comment area for developers.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

KZM9G uses an AS3711 PMIC to supply power to the CPU and the LCD backlight.
The PMIC on the board is pre-programmed to supply correct voltages to the
CPU, power supply to the backlight has to be turned on at run-time. The
latter is currently performed by a hard-coded I2C command sequence in the
board file. This patch removes the backlight hack and instead adds an I2C
device to instantiate the AS3711 MFD driver, which will add a regulator
device to dynamically adjust CPU voltages and a backlight device.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

As the kzm9d only has one smsc911x device it
may be registered as a platform device with id -1.

This allows the kzm9d board to access the smsc911x device
when CONFIG_REGULATOR (and CONFIG_REGULATOR_FIXED_VOLTAGE)
are set. The motivation for which is twofold: using regulators
seems to be generally a good thing; it will move the kzm9d defconfig
one step closer to being able to be consolidated with other
shmobile defconfigs.

An alternate but so far untested approach would be to
update the definition of dummy_supplies in board-kzm9d.c
to use "smsc911x.0" instead of "smsc911x".
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Bock-W board will needs more board specific ioremap() method.
This patch tidyup current FPGA specific settings
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The orignal commit 3263e09d287fbaa8a9424b5e69396599a3bbd518
(ARM: shmobile: Initial r8a73a4 SoC support V3)
put MP clock parent as EXTAL2, but its code was removed
on DIV6 clock support commit.
This patch makes it consistent.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Conflicts:
	arch/arm/mach-shmobile/Kconfig
	arch/arm/mach-shmobile/include/mach/r8a7778.h
	arch/arm/mach-shmobile/setup-r8a7778.c

According to the datasheet, it is not allowed to change div4 clock rates
if an earlier rate change operation is still in progress, as indicated by
a set kick bit.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

An earlier commit "ARM: shmobile: sh73a0: add support for adjusting CPU
frequency" intended to replace some clock operations only for the Z-clock,
instead it replaced them for all div4 clocks, since all div4 clocks share
the same copy of clock operations. Fix this by using a separate clock
operations structure for Z-clock.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Break out the function sh73a0_init_delay() that now
gets called both for the C version of the code and
the DT -reference boards. This way we handle both
cases in the same way.

Allows us to boot with TWD only in the kernel configuration
for C board code. TWD is not yet enabled in the case of
DT -reference - this due to a dependency on CCF.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This patch enables the use of the generic cpufreq-cpu0 driver on sh73a0.
Providing a regulator, a list of OPPs in DT, combined with a virtual
cpufreq-cpu0 platform device and a clock, attached to it is everything,
the cpufreq-cpu0 driver needs. The first sh73a0 platform, implementing
such CPUFreq support is kzm9g-reference.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

On SH73A0 the output of PLL0 is supplied to two dividers, feeding clock to
the CPU core and SGX. Lower CPU frequencies allow the use of lower supply
voltages and thus reduce power consumption.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Both clock-r8a7740.c and clock-r8a7790.c define a div4_clks array as
non-static. Compiling support for both SoCs thus result in a symbol
redefinition. Fix it by defining the arrays as static.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

DIV6 clocks control SD*/MMC* core clocks.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

DIV4 clocks control SD* core clocks.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Almost all clock needs main clock which is basis clock on r8a7790.
This patch adds it, and, set its parent/ratio via MD pin.
It is based on v0.05 datasheet
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This patch adds SDHI register function which needs id number (= 0/1/2)
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

R-Car M1 has many clocks, and it is possible to
read/use clock ratio of these clocks from FRQMRx.
But, these ratio are fixed value and
these are decided by MD pin status.

This patch reads MD pin status,
and used fixed ratio clock for other clocks.
It was tesed on bock-w board.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

DIV6 clocks control each core clocks.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

DIV4 clocks control each core clocks.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

PLL clocks are basis clock for other clock.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Almost all clock needs main clock which is basis clock on r8a73a4.
This patch adds it, and, set parent clock via CKSCR register.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add clock association for i2c0 and i2c1 for the new DT names.
Signed-off-by: Bastian Hecht <hechtb+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

When we use the ethernet device via DT setup, we need to add it
to a lookup list until this is properly handled later in a DT-only
fashion.
Signed-off-by: Bastian Hecht <hechtb+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Ether setup code position was scattering.
This patch fixes it up
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

SH_CLK_SET_RATIO() will be trouble without this patch
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>