The sharp-ls panel driver now manages the gpios required to configure the panel.
This was previously done in omap_dss_device's platform_enable/disable callbacks
defined in board files using this panel.

All the board files using this panel now pass the gpio information as platform
data via the panel_sharp_ls037v7dw01_data struct, which is needed by the panel
driver to configure the gpios connected to the panel. Hence, the
platform_enable/disable ops can be safely removed now.
Signed-off-by: Archit Taneja <archit@ti.com>

Move the GPIO handling from board file's platform callbacks to the panel
driver, which gets the gpios via platform data.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

The generic dpi panel driver now sets the gpios required to configure the panel.
This was previously done in platform_enable/disable callbacks in board files.

All the board files using generic dpi panel now correctly pass the gpio related
information as platform data, which is needed by the panel driver to configure
the panel. Hence, the platform_enable/disable ops can be safely removed now.
Signed-off-by: Archit Taneja <archit@ti.com>

The lgphilips panel driver now manages the gpios required to configure the
panel. This was previously done in omap_dss_device's platform_enable/disable
callbacks defined in board files using this panel.

All the board files using this panel now pass the gpio information as platform
data via the panel_generic_dpi_data struct, which is needed by the panel driver
to configure the gpios connected to the panel. Hence, the
platform_enable/disable ops can be safely removed now.
Signed-off-by: Archit Taneja <archit@ti.com>

The lgphilips panel driver leaves gpio configurations to the platform_enable
and disable calls in the platform's board file. These should happen in the
panel driver itself.

Use the platform data as defined for generic dpi panels to pass gpio information
to the lgphilips driver.

This will help in removing the need for the panel drivers to have platform
related callbacks.
Signed-off-by: Archit Taneja <archit@ti.com>

The generic dpi panel driver leaves gpio configurations to the platform_enable
and disable calls in the platform's board file. These should happen in the
panel driver itself.

Add a generic way of passing gpio information to the generic dpi panel driver
via it's platform_data. This information includes the number of gpios used by
the panel, the gpio number and logic level (active high/low) for each gpio. This
gpio data will be used by the driver to request and configure the gpios required
by the panel.

This will help in removing the need for the panel drivers to have platform
related callbacks.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>

The omap_dss_device structs's max_backlight_level is used to pass maximum
backlight level for the platform. However, no board file using this panel
populates this field. Therefore, we remove it's usage from the panel driver.
Signed-off-by: Archit Taneja <archit@ti.com>

Use devm_kzalloc instead of kzalloc to allocate driver data for the picodlp
panel driver. This simplifies the driver's probe and remove functions.
Signed-off-by: Archit Taneja <archit@ti.com>

Use devm_kzalloc instead of kzalloc to allocate driver data for the lg phillips
panel driver. This simplifies the driver's probe and remove functions.

Cc: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Archit Taneja <archit@ti.com>

Use devm_kzalloc instead of kzalloc to allocate driver data for the generic dpi
panel driver. This simplifies the driver's probe and remove functions.
Signed-off-by: Archit Taneja <archit@ti.com>

The n8x0 panel contains support to call platform backlight functions.
These are not used by any board, and can be removed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>

NEC-nl8048hl11 driver contains support to call platform backlight
functions. These are not used by any board, and can be removed.
Signed-off-by: Archit Taneja <archit@ti.com>

Sharp ls037v7dw01 driver contains support to call platform backlight
functions. These are not used by any board, and can be removed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>

acx565akm has support to call set_backlight/get_backlight in platform
code. They are not used by any board, and thus can be removed from the
driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>

Forthcoming panel patches will change the panel drivers to use platform
data to pass panel's gpios to the panel driver. This patch adds the
required fields and platform data structs to the omap-panel-data.h file,
so that the board files can be changed independently of the panel driver
changes.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>

Structs for platform data of omapdss panels are found in headers in the
'include/video/' path. Board files populate these structs with platform
specific values, and the panel driver uses these to configure the panel.

Currently, each panel has it's own header in the above path. Move all the
omapdss panel platform data structs to a single header omap-panel-data.h.
This is useful because:

- All other omapdss panel drivers will be modified to use platform data. This
  would lead to a lot of panel headers usable only by omapdss. A lot of these
  platform data structs are trivial, and don't really need a separate header.
- Platform data would be eventually removed, and platform information would be
  passed via device tree. Therefore, omapdss panel platform data structs are
  temporary, and will be easier to remove if they are all in the same header.
- All board files will have to include the same header to configure a panel's
  platform data, that makes the board files more consistent.
Signed-off-by: Archit Taneja <archit@ti.com>

Pull slave-dmaengine fixes from Vinod Koul:
 "Two fixes for slave-dmaengine.

  The first one is for making slave_id value correct for dw_dmac and
  the other one fixes the endieness in DT parsing"

* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
  dw_dmac: adjust slave_id accordingly to request line base
  dmaengine: dw_dma: fix endianess for DT xlate function

Pull media fixes from Mauro Carvalho Chehab:
 "For a some fixes for Kernel 3.9:
   - subsystem build fix when VIDEO_DEV=y, VIDEO_V4L2=m and I2C=m
   - compilation fix for arm multiarch preventing IR_RX51 to be selected
   - regression fix at bttv crop logic
   - s5p-mfc/m5mols/exynos: a few fixes for cameras on exynos hardware"

* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
  [media] [REGRESSION] bt8xx: Fix too large height in cropcap
  [media] fix compilation with both V4L2 and I2C as 'm'
  [media] m5mols: Fix bug in stream on handler
  [media] s5p-fimc: Do not attempt to disable not enabled media pipeline
  [media] s5p-mfc: Fix encoder control 15 issue
  [media] s5p-mfc: Fix frame skip bug
  [media] s5p-fimc: send valid m2m ctx to fimc_m2m_job_finish
  [media] exynos-gsc: send valid m2m ctx to gsc_m2m_job_finish
  [media] fimc-lite: Fix the variable type to avoid possible crash
  [media] fimc-lite: Initialize 'step' field in fimc_lite_ctrl structure
  [media] ir: IR_RX51 only works on OMAP2

Pull block fixes from Jens Axboe:
 "Alright, this time from 10K up in the air.

  Collection of fixes that have been queued up since the merge window
  opened, hence postponed until later in the cycle.  The pull request
  contains:

   - A bunch of fixes for the xen blk front/back driver.

   - A round of fixes for the new IBM RamSan driver, fixing various
     nasty issues.

   - Fixes for multiple drives from Wei Yongjun, bad handling of return
     values and wrong pointer math.

   - A fix for loop properly killing partitions when being detached."

* tag 'for-linus-20130331' of git://git.kernel.dk/linux-block: (25 commits)
  mg_disk: fix error return code in mg_probe()
  rsxx: remove unused variable
  rsxx: enable error return of rsxx_eeh_save_issued_dmas()
  block: removes dynamic allocation on stack
  Block: blk-flush: Fixed indent code style
  cciss: fix invalid use of sizeof in cciss_find_cfgtables()
  loop: cleanup partitions when detaching loop device
  loop: fix error return code in loop_add()
  mtip32xx: fix error return code in mtip_pci_probe()
  xen-blkfront: remove frame list from blk_shadow
  xen-blkfront: pre-allocate pages for requests
  xen-blkback: don't store dev_bus_addr
  xen-blkfront: switch from llist to list
  xen-blkback: fix foreach_grant_safe to handle empty lists
  xen-blkfront: replace kmalloc and then memcpy with kmemdup
  xen-blkback: fix dispatch_rw_block_io() error path
  rsxx: fix missing unlock on error return in rsxx_eeh_remap_dmas()
  Adding in EEH support to the IBM FlashSystem 70/80 device driver
  block: IBM RamSan 70/80 error message bug fix.
  block: IBM RamSan 70/80 branding changes.
  ...

This reverts commit 6aa97070.

Commit 6aa97070 ("lockdep: check that no locks held at freeze time")
causes problems with NFS root filesystems.  The failures were noticed on
OMAP2 and 3 boards during kernel init:

  [ BUG: swapper/0/1 still has locks held! ]
  3.9.0-rc3-00344-ga937536b #1 Not tainted
  -------------------------------------
  1 lock held by swapper/0/1:
   #0:  (&type->s_umount_key#13/1){+.+.+.}, at: [<c011e84c>] sget+0x248/0x574

  stack backtrace:
    rpc_wait_bit_killable
    __wait_on_bit
    out_of_line_wait_on_bit
    __rpc_execute
    rpc_run_task
    rpc_call_sync
    nfs_proc_get_root
    nfs_get_root
    nfs_fs_mount_common
    nfs_try_mount
    nfs_fs_mount
    mount_fs
    vfs_kern_mount
    do_mount
    sys_mount
    do_mount_root
    mount_root
    prepare_namespace
    kernel_init_freeable
    kernel_init

Although the rootfs mounts, the system is unstable.  Here's a transcript
from a PM test:

  http://www.pwsan.com/omap/testlogs/test_v3.9-rc3/20130317194234/pm/37xxevm/37xxevm_log.txt

Here's what the test log should look like:

  http://www.pwsan.com/omap/testlogs/test_v3.8/20130218214403/pm/37xxevm/37xxevm_log.txt

Mailing list discussion is here:

  http://lkml.org/lkml/2013/3/4/221

Deal with this for v3.9 by reverting the problem commit, until folks can
figure out the right long-term course of action.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Mandeep Singh Baines <msb@chromium.org>
Cc: Jeff Layton <jlayton@redhat.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: <maciej.rutecki@gmail.com>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ben Chan <benchan@chromium.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull SCSI target fixes from Nicholas Bellinger:
 "This includes the bug-fix for a >= v3.8-rc1 regression specific to
  iscsi-target persistent reservation conflict handling (CC'ed to
  stable), and a tcm_vhost patch to drop VIRTIO_RING_F_EVENT_IDX usage
  so that in-flight qemu vhost-scsi-pci device code can detect the
  proper vhost feature bits.

  Also, there are two more tcm_vhost patches still being discussed by
  MST and Asias for v3.9 that will be required for the in-flight qemu
  vhost-scsi-pci device patch to function properly, and that should
  (hopefully) be the last target fixes for this round."

* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
  target: Fix RESERVATION_CONFLICT status regression for iscsi-target special case
  tcm_vhost: Avoid VIRTIO_RING_F_EVENT_IDX feature bit

On some hardware configurations we have got the request line with the offset.
The patch introduces convert_slave_id() helper for that cases. The request line
base is came from the driver data provided by the platform_device_id table.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

As reported by Wu Fengguang's build robot tracking sparse warnings, the
dma_spec arguments in the dw_dma_xlate are already byte swapped on
little-endian platforms and must not get swapped again. This code is
currently not used anywhere, but will be used in Linux 3.10 when the
ARM SPEAr platform starts using the generic DMA DT binding.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

The Adam Belay's e-mail address in MAINTAINERS under PNP SUPPORT
is not valid any more and I started to maintain that code in the
meantime as a matter of fact, so list myself as a maintainer of it
along with Bjorn and remove the Adam's entry from it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull ceph fix from Sage Weil:
 "This fixes a regression introduced during the last merge window when
  mapping non-existent images."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
  rbd: don't zero-fill non-image object requests

A result of ENOENT from a read request for an object that's part of
an rbd image indicates that there is a hole in that portion of the
image.  Similarly, a short read for such an object indicates that
the remainder of the read should be interpreted a full read with
zeros filling out the end of the request.

This behavior is not correct for objects that are not backing rbd
image data.  Currently rbd_img_obj_request_callback() assumes it
should be done for all objects.

Change rbd_img_obj_request_callback() so it only does this zeroing
for image objects.  Encapsulate that special handling in its own
function.  Add an assertion that the image object request is a bio
request, since we assume that (and we currently don't support any
other types).

This resolves a problem identified here:
    http://tracker.ceph.com/issues/4559

The regression was introduced by bf0d5f50.
Reported-by: Dan van der Ster <dan@vanderster.com>
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-off-by: Sage Weil <sage@inktank.com>

Pull btrfs fixes from Chris Mason:
 "We've had a busy two weeks of bug fixing.  The biggest patches in here
  are some long standing early-enospc problems (Josef) and a very old
  race where compression and mmap combine forces to lose writes (me).
  I'm fairly sure the mmap bug goes all the way back to the introduction
  of the compression code, which is proof that fsx doesn't trigger every
  possible mmap corner after all.

  I'm sure you'll notice one of these is from this morning, it's a small
  and isolated use-after-free fix in our scrub error reporting.  I
  double checked it here."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Btrfs: don't drop path when printing out tree errors in scrub
  Btrfs: fix wrong return value of btrfs_lookup_csum()
  Btrfs: fix wrong reservation of csums
  Btrfs: fix double free in the btrfs_qgroup_account_ref()
  Btrfs: limit the global reserve to 512mb
  Btrfs: hold the ordered operations mutex when waiting on ordered extents
  Btrfs: fix space accounting for unlink and rename
  Btrfs: fix space leak when we fail to reserve metadata space
  Btrfs: fix EIO from btrfs send in is_extent_unchanged for punched holes
  Btrfs: fix race between mmap writes and compression
  Btrfs: fix memory leak in btrfs_create_tree()
  Btrfs: fix locking on ROOT_REPLACE operations in tree mod log
  Btrfs: fix missing qgroup reservation before fallocating
  Btrfs: handle a bogus chunk tree nicely
  Btrfs: update to use fs_state bit

Commit 3e7fc708 ("ia64 idle: delete pm_idle") in 3.9-rc1 didn't
finish the job, leaving an un-initialized reference to (*idle)().

[ Haven't seen a crash from this - but seems like we are just being
  lucky that "idle" is zero so it does get initialized before we jump to
  randomland  - Len ]
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull arc architecture fixes from Vineet Gupta:
 "This includes fix for a serious bug in DMA mapping API, make
  allyesconfig wreckage, removal of bogus email-list placeholder in
  MAINTAINERS, a typo in ptrace helper code and last remaining changes
  for syscall ABI v3 which we are finally starting to transition-to
  internally.

  The request is late than I intended to - but I was held up with
  debugging a timer link list corruption, for which a proposed fix to
  generic timer code was sent out to lkml/tglx earlier today."

* 'for-curr' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
  ARC: Fix the typo in event identifier flags used by ptrace
  arc: fix dma_address assignment during dma_map_sg()
  ARC: Remove SET_PERSONALITY (tracks cross-arch change)
  ARC: ABIv3: fork/vfork wrappers not needed in "no-legacy-syscall" ABI
  ARC: ABIv3: Print the correct ABI ver
  ARC: make allyesconfig build breakages
  ARC: MAINTAINERS update for ARC

A user reported a panic where we were panicing somewhere in
tree_backref_for_extent from scrub_print_warning.  He only captured the trace
but looking at scrub_print_warning we drop the path right before we mess with
the extent buffer to print out a bunch of stuff, which isn't right.  So fix this
by dropping the path after we use the eb if we need to.  Thanks,

Cc: stable@vger.kernel.org
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>

This patch fixes a regression introduced in v3.8-rc1 code where a failed
target_check_reservation() check in target_setup_cmd_from_cdb() was causing
an incorrect SAM_STAT_GOOD status to be returned during a WRITE operation
performed by an unregistered / unreserved iscsi initiator port.

This regression is only effecting iscsi-target due to a special case check
for TCM_RESERVATION_CONFLICT within iscsi_target_erl1.c:iscsit_execute_cmd(),
and was still correctly disallowing WRITE commands from backend submission
for unregistered / unreserved initiator ports, while returning the incorrect
SAM_STAT_GOOD status due to the missing SAM_STAT_RESERVATION_CONFLICT
assignment.

This regression was first introduced with:

commit de103c93
Author: Christoph Hellwig <hch@lst.de>
Date:   Tue Nov 6 12:24:09 2012 -0800

    target: pass sense_reason as a return value

Go ahead and re-add the missing SAM_STAT_RESERVATION_CONFLICT assignment
during a target_check_reservation() failure, so that iscsi-target code
sends the correct SCSI status.

All other fabrics using target_submit_cmd_*() with a RESERVATION_CONFLICT
call to transport_generic_request_failure() are not effected by this bug.
Reported-by: Jeff Leung <jleung@curriegrad2004.ca>
Cc: Christoph Hellwig <hch@lst.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

This patch adds a VHOST_SCSI_FEATURES mask minus VIRTIO_RING_F_EVENT_IDX
so that vhost-scsi-pci userspace will strip this feature bit once
GET_FEATURES reports it as being unsupported on the host.

This is to avoid a bug where ->handle_kicks() are missed when EVENT_IDX
is enabled by default in userspace code.

(mst: Rename to VHOST_SCSI_FEATURES + add comment)
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Asias He <asias@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>

This reverts commit 18693050 ("mm: introduce VM_POPULATE flag to
better deal with racy userspace programs").

VM_POPULATE only has any effect when userspace plays racy games with
vmas by trying to unmap and remap memory regions that mmap or mlock are
operating on.

Also, the only effect of VM_POPULATE when userspace plays such games is
that it avoids populating new memory regions that get remapped into the
address range that was being operated on by the original mmap or mlock
calls.

Let's remove VM_POPULATE as there isn't any strong argument to mandate a
new vm_flag.
Signed-off-by: Michel Lespinasse <walken@google.com>
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull USB fixes from Greg Kroah-Hartman:
 "Here are some USB fixes to resolve issues reported recently, as well
  as a new device id for the ftdi_sio driver."

* tag 'usb-3.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  usb: ftdi_sio: Add support for Mitsubishi FX-USB-AW/-BD
  usb: Fix compile error by selecting USB_OTG_UTILS
  USB: serial: fix hang when opening port
  USB: EHCI: fix bug in iTD/siTD DMA pool allocation
  xhci: Don't warn on empty ring for suspended devices.
  usb: xhci: Fix TRB transfer length macro used for Event TRB.
  usb/acpi: binding xhci root hub usb port with ACPI
  usb: add find_raw_port_number callback to struct hc_driver()
  usb: xhci: fix build warning

Pull TTY/serial fixes from Greg Kroah-Hartman:
 "Here are some tty/serial driver fixes for 3.9.

  The big thing here is the fix for the huge mess we caused renaming the
  8250 driver accidentally in the 3.7 kernel release, without realizing
  that there were users of the module options that suddenly broke.  This
  is now resolved, and, to top the injury off, we have a backwards-
  compatible option for those users who got used to the new name since
  3.7.  Ugh, sorry about that.

  Other than that, some other minor fixes for issues that have been
  reported by users."

* tag 'tty-3.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  Xilinx: ARM: UART: clear pending irqs before enabling irqs
  TTY: 8250, deprecated 8250_core.* options
  TTY: 8250, revert module name change
  serial: 8250_pci: Add WCH CH352 quirk to avoid Xscale detection
  tty: atmel_serial_probe(): index of atmel_ports[] fix

Pull staging driver fixes from Greg Kroah-Hartman:
 "Here are two tiny staging driver fixes to resolve issues that have
  been reported."

* tag 'staging-3.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging: comedi: s626: fix continuous acquisition
  staging: zcache: fix typo "64_BIT"

Pull sysfs fixes from Greg Kroah-Hartman:
 "Here are two fixes for sysfs that resolve issues that have been found
  by the Trinity fuzz tool, causing oopses in sysfs.  They both have
  been in linux-next for a while to ensure that they do not cause any
  other problems."

* tag 'driver-core-3.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  sysfs: handle failure path correctly for readdir()
  sysfs: fix race between readdir and lseek

Pull char/misc driver fixes from Greg Kroah-Hartman:
 "Here are some small char/misc driver fixes that resolve issues
  recently reported against the 3.9-rc kernels.  All have been in
  linux-next for a while."

* tag 'char-misc-3.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  VMCI: Fix process-to-process DRGAMs.
  mei: ME hardware reset needs to be synchronized
  mei: add mei_stop function to stop mei device
  extcon: max77693: Initialize register of MUIC device to bring up it without platform data
  extcon: max77693: Fix bug of wrong pointer when platform data is not used
  extcon: max8997: Check the pointer of platform data to protect null pointer error

Pull ACPI and power management fixes from Rafael J Wysocki:

 - Fix for a recent cpufreq regression related to acpi-cpufreq and
   suspend/resume from Viresh Kumar.

 - cpufreq stats reference counting fix from Viresh Kumar.

 - intel_pstate driver fixes from Dirk Brandewie and Konrad Rzeszutek
   Wilk.

 - New ACPI suspend blacklist entry for Sony Vaio VGN-FW21M from Fabio
   Valentini.

 - ACPI Platform Error Interface (APEI) fix from Chen Gong.

 - PCI root bridge hotplug locking fix from Yinghai Lu.

* tag 'pm+acpi-3.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  PCI / ACPI: hold acpi_scan_lock during root bus hotplug
  ACPI / APEI: fix error status check condition for CPER
  ACPI / PM: fix suspend and resume on Sony Vaio VGN-FW21M
  cpufreq: acpi-cpufreq: Don't set policy->related_cpus from .init()
  cpufreq: stats: do cpufreq_cpu_put() corresponding to cpufreq_cpu_get()
  intel-pstate: Use #defines instead of hard-coded values.
  cpufreq / intel_pstate: Fix calculation of current frequency
  cpufreq / intel_pstate: Add function to check that all MSRs are valid