Add dispc_mgr_get_vsync_irq() which returns the irq number for vsync on
the given channel.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Create separate functions for the vsync isr register/unregister code for
cleaner code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Current way of handling overlay-manager links is a bit strange: each
manager has a static array, containing pointers to all the overlays
(even those used by other managers). The overlays contain a pointer to
the manager being used.

This patch makes the system a bit saner: each manager has a linked list
of overlays, and only the overlays linked to that manager are in the
list.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Overlay managers are stored in a linked list. There's no need for this
list, as an array would do just as fine.

This patch changes the code to use an array for overlay managers.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Overlays are stored in a linked list. There's no need for this list, as
an array would do just as fine.

This patch changes the code to use an array for overlays.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

dss_mgr_start_update() has a loop, of which sole purpose is to find the
manager used for this update. The whole loop is extra, as we already
know the manager.

Remove the loop.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

There's no need to register the vsync ISR and configure the hardware if
the overlay manager is disabled, so this patch adds a check for disabled
managers to the omap_dss_mgr_apply() function.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

The mechanism to cache manager and overlay settings and configure them
into the HW registers in VSYNC is meant only for auto-update displays,
as it doesn't make sense (and doesn't work) for manual-update displays.

This patchs adds a check so that we skip the above for manual update
displays.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Add "enabled" field to struct omap_overlay_manager, which tells if the
output is enabled or not. This will be used in apply.c in the following
patches.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

omap_overlay_manager struct contains enable() and disable() functions.
However, these are only meant to be used from inside omapdss, and thus
it's bad to expose the functions.

This patch adds dss_mgr_enable() and dss_mgr_disable() functions to
apply.c, which handle enabling and disabling the output.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Create a new file, apply.c, and move code about handling the
apply-mechanism and configuration of the managers and overlays from
manager.c to apply.c.

Not all related code is moved in this patch, but only the core
apply/configure functions. The later patches move rest of the code from
overlay.c and manager.c, adding necessary locking at the same time.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

omap_dss_mgr_apply currently applies settings to all overlays and
overlay managers. The reason for this was to support cases where
configuration changes affecting multiple managers are made. However, the
current code doesn't support changing such configurations, so the
functionality is not needed.

Change the apply to affect only the manager given as an argument, and
the overlays attached to that manager.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Split omap_dss_mgr_apply() into smaller functions for clarity.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Add helper functions ovl_manual_update() and mgr_manual_update() which
return whether the overlay or manager is used with a manual update
display.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

There's an unnecessary wrapper function, dss_ovl_wait_for_go(), which
does nothing else than call dss_mgr_wait_for_go_ovl(). The
dss_ovl_wait_for_go() function can be removed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Remove unused functions:

dispc_mgr_get_default_color
dispc_mgr_get_trans_key
dispc_mgr_trans_key_enabled
dispc_mgr_alpha_fixed_zorder_enabled
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Change manager configuration to be similar to overlay configuration by
creating dispc_mgr_setup() which takes omap_overlay_manager_info as
parameter.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Overlay channel is configured with ovl_setup, with all the other overlay
attriutes. This patch separates overlay channel setup so that we can
later configure the channel only when needed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Overlay FIFO thresholds are configured with ovl_setup, with all the
other overlay attributes. This patch separates FIFO threshold setup so
that we can later configure FIFO thresholds only when needed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Move the configuration of interlace and replication from
omap_dss_mgr_apply() to configure_overlay(). This removes the need to
store the values into the cache data.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Overlay out_width/height are set to 0 when scaling is not used by the
users of omapdss. Currently ovl_setup() expects the caller of
ovl_setup() to convert those zero values to width or height.

This patch makes ovl_setup() accept zero values for out_width/height,
making calling ovl_setup() a bit simpler as the overlay_info can be
just passed to this function without modifications.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

dss_start_update() takes currently the dss device as a parameter. Change
the parameter to ovl manager, as that is what the dss_start_update()
actually needs. Change the name of the function to
dss_mgr_start_update() to reflect the change.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Partial update for manual update displays has never worked quite well:
* The HW has limitations on the update area, and the x and width need to
  be even.
* Showing a part of a scaled overlay causes artifacts.
* Makes the management of dispc very complex

Considering the above points and the fact that partial update is not
used anywhere, this and the following patches remove the partial update
support. This will greatly simplify the following re-write of the apply
mechanism to get proper locking and additional features like fifo-merge.

This patch removes the partial update from the panel-taal.c.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Partial update for manual update displays has never worked quite well:
* The HW has limitations on the update area, and the x and width need to
  be even.
* Showing a part of a scaled overlay causes artifacts.
* Makes the management of dispc very complex

Considering the above points and the fact that partial update is not
used anywhere, this and the following patches remove the partial update
support. This will greatly simplify the following re-write of the apply
mechanism to get proper locking and additional features like fifo-merge.

This patch removes the partial update from the dsi.c.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Partial update for manual update displays has never worked quite well:
* The HW has limitations on the update area, and the x and width need to
  be even.
* Showing a part of a scaled overlay causes artifacts.
* Makes the management of dispc very complex

Considering the above points and the fact that partial update is not
used anywhere, this and the following patches remove the partial update
support. This will greatly simplify the following re-write of the apply
mechanism to get proper locking and additional features like fifo-merge.

This patch removes the partial update from the manager.c.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Make dispc_ovl_set_fifo_threshold() public so that later patches can
handle overlay fifo configuration.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Make dispc_ovl_set_channel_out() public so that later patches can handle
changing overlay's manager.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Some old example code has been left lying around. Remove the example
code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Once in a time omapdss had basic support for fifomerge. Fifomerge was
removed as the implementation didn't work properly, and a proper
implementation is a complex problem.

However, some unused fifo-merge related code was left behind. This patch
removes those.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

dispc_mgr_is_enabled() was missing a prototype in dss.h
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

ULPS cannot be entered if the DDR clk is enabled. Thus disable the DDR
clk before entering ULPS.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

We sometimes get timeout when disabling the DSI interface with video
mode. It looks like the disable will stall until the current frame has
been finished, and this can take multiple milliseconds.

wait_for_bit_change() currently uses a busyloop to wait for a bit to
change. This is used in multiple places. The problem is, we don't have
clear understanding how long particular operations can take, so the
function needs to support longer waits.

Improve wait_for_bit_change() to first busy loop for 100 times to see if
the bit changes almost right away. If the bit hasn't changed, move to a
loop with a sleep of 1ms, and poll for 500ms.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

The current code always enters ULPS for 3 lanes. This is not right, as
there could be only 2 lanes used, and on OMAP4 we have 5 lanes.

Fix the code to put all used lanes into ULPS.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

There's no longer need for the dsi_get_num_lanes_used function, so it
can be removed. The lane check in dsi_init_display() can be removed as
the validity of the config will be verified when parsing it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Use the new lane config in dsi_cio_enable_lane_override(). The function
parameters are also slightly changed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Use the new lane config in dsi_cio_wait_tx_clk_esc_reset(). This also
extends the function to support 5 lanes on OMAP4, instead of 3 lanes.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Use the new lane config in dsi_get_lane_mask().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Use the new lane config in dsi_set_lane_config().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Parse the lane configuration from the device data into internal lane
config format. This will be used in the following patches to clean up
the lane handling.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

DSI driver currently counts used lanes and number of supported lanes by
using the number of data lanes (i.e. excluding clock lane). This patch
changes this to use the number of all lanes so that the following lane
config patches are cleaner.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>